E2000 router

Similar Questions

• E2000 router and the NAS QNAP TS-212

  Hello

  I've been a happy user of a quite old WRT54G and a NAS QNAP TS-212 for quite awhile.

  But recently, the router is dead so I bought a new - this time, the model E2000.

  Since then, the AFP (Apple protocol) connection to the NAS Server works only for a couple of hours after reboot of the router. I tried to restart the router and the NAS - only restart the router allows, in addition he has worked with the former, so I guess the E2000 is to blame.

  The connection through the web to the NAS works all the time.

  Any ideas where to look for a potential solution? How to diagnose what the problem?

  Kind regards

  Adam

  Does this happen with wired or Wi - Fi?

  Connect the computer to the router with the Ethernet cable and check to see if you face the same problem with the wired connection.

  If it is with the wired connection too, then try the following.  In this case, you can try to reduce the speed of the LAN. Here are the steps:

  START--> right click on my network places, and then click Properties

  Right-click on the device, and then click Properties

  Click on the button set UP

  Select the ADVANCED tab and settings, you can change appear on the left.

  If the problem is with the Wi - Fi connection and then try to change some advanced on the router settings wireless.

  Open the router configuration page and go to the tab settings wireless wireless Advanced tab Change the tag to 75 interval, RTS threshold and fragmentation to 2304. Save the settings.

• Linksys E2000 router slow connection.

  OK, so I use 2 with 2 routers, for me and my father, another for my brother and sister.  We decided to get rid of the other router and make our cisco E2000 our primary router, but everything on the router configuration has been deleted, so we had to reset upward.  I remember reading a guide to advanced setting to make my wireless speed range from 13.5MBPS to 216 Mbit/s, but I forgot what the settings was in the advance settings.  Can someone help me with the settings or if you have a link that I can go?

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER...
  Let the empty user name & password use admin lowercase...

  Click on the Wireless tab > click on Advanced Wireless Settings...
  Change the tag to 75 interval, change the Fragmentation threshold to 2304, change the RTS threshold to 2304 and click on save settings... Now let's see if you can locate your wireless network and try to connect...

• Problem HP 6500 wireless has more and linksys E2000 router

  Hello

  Just bought a HP 65000 has more the printer today and want to connect it to my wireless router, which works very well for all my other devices and worked very well for my old Epson as well.

  The router configuration:

  Security: WPA/WPA2 Mixed Mode

  Channel: 6

  Band 2.4 Ghz

  Configure a static ip address 192.168.1.22 for HP based on its mac address.

  Sometimes printer says that it cannot find the network, which results in FAILURE messages on the wireless network test report. other times it connects, gets the right ip address, which translates as PASS messages on the test report, but it seems to disconnect again because he repeats to me it is not connected and I don't find it with any computer. The website of the printer is also not available.

  Any ideas?

  Thanks for your time.

  What brand/model of router and what kind of ISP?  Have you tried to channel 11?

• Cisco Connect connects to the router E2000

  I got an E2000 router, set up and works very well for years. Today, I tried to connect with Cisco Connect, I want to establish a network of separate comments (by the way, if there's a way to do this through the web management interface, please let me know!). However, the software is unable to connect to the router; the progress bar gets to 25%, and then eventually times out. I tried several computers on network, cable and wireless, with the same results. Any suggestions? Thank you!

  I solved the problem; I activated the setting "Allow users to set up" in the "Administration" tab, as well as utility access Web via HTTP. I don't know which of these settings did the trick, but I was able to connect and configure the network invited (even from a PC wireless).

• Use E2000 as ONLY - wireless access point not as a router

  I would use my E2000 router as an only Wi - Fi access point. The unit will be connected to a unit of combo modem/router Verizon FiOS Actiontek I want to leave only the first and only router on my network. Can the E2000 cause its router functions disabled without DD - WRT or other third party firmware?

  Thank you!

  Yes, but you need to connect a cable between the router to the AP, here's how

  Editing cascading (connecting) a Linksys router to another router

• Question re: Atheros AR5007 802. 11 b / g adapter and connection w/Linksys E2000 wireless router

  Help! I'm at my wit's end. I just bought a Linksys E2000 router and cannot find a way to get the router to connect wireless on my HP G60-235DX laptop (running Vista) via the WPA2 setting. I know that the Atheros AR5007 802. 11 b / g wifi adapter is the question, and I downloaded the latest driver update... and still have the same problems.

  FYI - I can connect to the computer via the internet cable from the Linksys E2000 router so I know that it is not a modem issue.

  Help... PLEASE, I BEG YOU!

  Thank you, thank you, thank you...

  Paul,

  I solved the problem! After almost return the router to Best Buy today during lunch, I decided to give it a try more tonight and again call LinkSys. After almost decided with the Linksys officer that they only solution is to put another card in my computer, we stumbled on the question.

  We have gone to 5.0 GHz to 2.4 and spent the 'auto' channel to channel 9.

  And now my computer works like a charm (thanks also to update the driver as you instructed).

  Thank you!

• Unable to connect to the wireless router. No ip address

  Recently, I plugged a Linksys E2000 router to connect two computers for internet access. Computer has access. 2nd computer cannot obtain an ip address. using windows xp sp 3. Technical support was no help.

  Hello

  As a first step put the computer near the router and start with the security off the coast.
  When it works, take it back to the final spot. If it stops then working, then you have a problem of distance.

  In general

  My wireless is not working - http://www.ezlan.net/wireless.html

  Basic wireless configuration - http://www.ezlan.net/Wireless_Config.html

  Wireless Security - http://www.ezlan.net/Wireless_Security.html

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• router

  Hello

  How can I find my ID and my password for my router my notes were lost when moving.

  E2000 router.

  Thank you.

  Empty default, leave username password "admin".   If you have changed your password to something else and don't remember you must hard reset the router and reconfigure your settings.  The information above will not work.

• Linksys E2000 to into acccess point/switch helps.

  Okay so here's the deal, we got At & T Modem/Router upstairs, and then we had a long cable ethernet connecting here in the basement. The problem is that this allows only a connection to the local network at the same time (a problem for LAN parties and others). I do have a Linksys E2000 router however and I want to be able to use it as a switch access point.
  I'm sure this is possible, but I forgot all the steps to do so.
  The att modem/router is running on 192.168.1.254 and my Linksys that is directly connected is on 192.168.1.1, so I have another address in this field.
  What I need to change my Linksys settings now, or do I have to change the settings for at & t?
  Basic steps would be appreciated, but I am familiar with the concepts of normal network, so you mustn't it level by the low that much.
  Also I will use this for Xbox Live at points so will I need to re - open all the ports on my Linksys, or at least put the DHCP to static IP Xbox to keep my NAT good?

  Thank you
  -Austin

  Two types of installation would be possible. Click on the following link to find out how the configuration.

  Editing cascading (connecting) a Linksys router to another router

• WAP54G Repeater connecting an E2000

  I just installed an E2000 router in an office on the first floor. The signal strength is very low down, so my question is:

  Can I use a wap54g as a Repeater. If so, how do the MAC address of the E2000?

  Second question. The E2000 has two bands and is running at 2.4. The range would increase if I changed the setting to 5.

  Thank you. I bought 1000 re

• E2000 low connection speeds

  I recently "upgraded" my router from a WRT54G for the E2000 and changed my computers wireless to USB - N adapters. At first, they were only 54 Mbps but found that I had to use WPA2 (I was in WPA) and after the change is made, I got from around 107Mbps to 130Mbps connections. (Even if these are dual band adapters, I can't enjoy 300Mbps because I left the Router 2.4 Ghz only because I have some only portable wireless-G and I understand that you can not on 5 GHz router because they do not connect.)  In any case, a few days later, when I checked these computers wireless n connection speed, one was at 5 Mbps, another 20 - something.  The signal strength is good at computers, as it has always been.  This router "modifies" speeds "as needed" or something?  Any help is greatly appreciated!

  I think 2.4 GHz is faster than the 5 GHz Wireless band.

  You can connect the router WRT54G of E2000 router to create a new 2.4 Ghz wireless network and allows you to broadcast the signal 5 GHz E2000 wireless router.

  Follow this link to cascading Linksys router to another router.

• FIOS/E2000 problem

  Hello

  A few weeks ago, I bought a router E2000 because I wanted the comments WiFi feature.  I ran EasyConnect, everything set up successfully and made a disc USB EasyConnect.  Everything was fine.

  It was with Verizon DSL.  Yesterday, I had Verizon FIOS (telephone, television and internet) installed. Verizon installers will not help with a LinkSys Router, so he has set up the network using the Verizon router.  Now, I'm trying to configure the E2000, so I can use the WiFi from comments.  All I need is the WiFi guest: I'm happy to let the router Verizon DHCP and nothing else. FIOS requires their router is used because it is necessary to provide information of cable for the TV guide.  In addition, the output of the internet in the area of FIOS (NTA) is coax. So, I need to use the Verizon router and the E2000.  I started by connecting a PC cable to the E2000 and running the USB EasyConnect.  Which failed, because the EasyConnect connection could not find an internet connection.  So I added a cable since the E2000 router Verizon (both outlets numbered, not the internet), the power to bike on the E2000 and tried again.  This time he has not once again and was told that the computer is not connected to the router.  Apparently, EasyConnect requires a direct connection to an internet modem to work.  And the E2000 has the unpleasant feature configuration pages to browser to 192.168.1.1, that works well, is not able to set up the WiFi comments function: single EasyConnect can do.  Since EasyConnect will not work and the browser interface will not install the WiFi client, it seems that I'm dead in the water.

  I tried the Linksys Online Chat.  They could not help, but he referred me to the helpline.  They took care of "set expectations" telling me that FIOS is such an obscure and rare technology that the router can not work at all with it.  They could not help with the problem, but rather, I rise to yet a higher support level.  They could not help, but said that someone at a higher level (so high that I could not get the phone number).   Needless to say that they do not have.

  I don't know what else to do.  Does anyone know how do my guest E2000 work feature WiFi with FIOS?

  Thank you

  Mike

  Linksys support called.  The lady was very knowledgeable and helpful, and did a great job.   Because I wrote it for myself in case I need it again, I thought I'd share.

  To do this, each router must have its own subnet, with its own DHCP, so the Internet of the E2000 port must be connected to a numbered Verizon Actiontec router port.  The other approach, where there is only a single subnet and a regular port of the E2000 is used, won't work because CiscoConnect will not work if there is no internet connection available in its WAN port.  Unfortunately, that means MS printer and file sharing does not work between two subnets. That could be fixed by using the static if necessary routes, but I didn't do that.  The WiFi to a router can be used.  Since I wanted the comments E2000 WiFi feature, I'll use the E2000 WiFi.  The steps are:

  1. Connect the PC to the Actiontec router that needs access to the internet.
  2. Launch IE and access the Actiontec router at 192.168.1.1.  Log in, probably with credentials of (admin, admin) or (admin, password1) and turn off the WiFi.
  3. Download the most recent update of firmware and software of CiscoConnect.  Visit www.linksys.com, click support, enter router model E2000, click on download, select worm. 1 and download CiscoConnect for Windows and the latest firmware of the router.
  4. Connect the PC to the E2000 numbered ports and connect the Internet of the E2000 port to the Actiontec router ports numbered.
  5. Launch IE and the E2000 access 192.168.1.1.  Click on the Administration tab, then click on Firmware Upgrade, then browse to locate the firmware file (* .bin) downloaded previously, and then click upgrade.  Once the upgrade is complete, wait for the router power light stop flashing and go solid.
  6. If necessary to log in on the E2000 once again, or otherwise just refresh the page.  Click the Administration tab, and then click Factory Defaults, then restore to factory defaults, then restore all settings.
  7. Click the Configuration tab.  Change the IP Address of the router Network Setup of 192.168.1.1 to 192.168.2.1 and save the settings.  From now on, use this IP address to configure the E2000.
  8. Open a command window (from the command menu, type 'cmd' and press ENTER, click Run) & then run "ipconfig/release" then "ipconfig / renew".  The displayed gateway should be 192.168.2.1.
  9. Launch the previously downloaded CiscoConnect software.  Now, it should work.

  10. now, you can configure your E2000.  The router configuration to set the name of the router and the password for WiFi LAN connections, who is also the password for the configuration of the router.  Guest network allows to change the password for the guest network.  Click Add a computer to the parental control for wireless clients.

  That's all.  Enjoy.

  Mike

  (Mod Note: deleted non-public information.) (Thank you.)

• E2000 Firmware download 0 bytes

  I'm trying to update my E2000 router to the latest firmware, but when I upload the .bin file is empty (0 byte).  I tried to disable the anti-virus and also tried two different browsers, IE and Firefox.  Anyone else have similar problems?  I'm trying to get the firmware from the following URL (Download tab):

  http://homesupport.Cisco.com/en-us/Wireless/Linksys/E2000

  The name of the firmware file is:

  FW_E2000_1.0.03.002_US_20100907_code.bin

  Any help or corroboration would be appreciated.

  tried to download the file. It worked, size ~5.2MB

  You can try to download from another computer?

• Web site filtering by keywords only at certain times of the day - E3000

  I want to enable members of the family who have access to the internet via my E3000 router (including me) to the only access some Web sites the night to improve our productivity.  I want to filter the keyword 'facebook' and set it so access to the URLs/images with that keyword will only be allowed to 17:00 to 23:00, or denied from 23:00 to 17:00.  I can't find anything to make it work with the interface, denying by keyword only during certain hours.  Can someone who KNOWS tell me what must be completed to make this work, you?  Thank you!

  It comes to my admin screen for what I believe:

  

  E3000E3000E3000

  Hi HughK,

  I guess that's how the Linksys has designed. I tried with my sister E2000 router and I can only "Refuse" to specific time and day, but not the "key words".