E3000 broadcast fails

Similar Questions

• EA2700 smart wifi keeps bug broadcast even if SSID wireless disabled

  Ver.1.1.39.145204 is the firmware.

  Cutting the 2.4 Ghz and 5 Ghz wifi does not interrupt the transmission of a SSID.

  If allow wireless admin is checked the continuous SSID broadcasting on 5 GHz and 2.4 Ghz bands.

  If not checked the SSID then forwards on the 5 GHz band.

  In both cases, the SSID is transmitted are the default SSID of the factory, and he announced a nonsecure connection.  (router erases your security settings when you turn off a radio)

  On the plus side tent to connect to the wrong ssid broadcast failed, but he always seems a bad idea to advertising a connection open 24 hours a day.

  I tried to report it to the Linksys technical support.  Their response was to reload the firmware.  That I did - but it does not change the behavior of this SSID bug.  I asked them to report it as a bug and the Lady declined.

  Does anyone know how to make a break from the SSID when Wifi is disabled?

  Thanks for the reply.  After reboot, then reload the firmware and then reboot the router, five times the problem disappeared.

  I was using an IPAD with IOS 7.1 and a samsung with android phone to test.

• IOVP NIC certification broadcast test case failed due to "VM is in an invalid POWER State"

  Hi, I use workbench 3.0.2 to run VMware Esxi 5.5 U2 NIC certification.

  I spent the first 3 automated cases: Install::Driver:VIBwithTestKey, Install::Config:Driver Update, Version_Check.

  Now I'm stuck with the case of dissemination because of the error "VM is in an invalid POWER State", but it's ok for me to start the VM manunally.

  2 virtual machines are created and fully automatically started on host by workbench, and two of them are assigned the same name 'vtafVM1_192.168.49.168_4740'.

  The newspaper on the workbench is as below:

  [March 25, 2015 02:34:21: VIRTUALMAC] [0] DEBUG: end CreateVirtualNic()

  [March 25, 2015 02:34:21: TESTHASH] [0] FRAME: reuse an available in the container instance

  [March 25, 2015 02:34:21: STAFBASE] [0] FRAME: command execution STAF: staf VTAF_VM localhost connect agent 192.168.49.168 root password userid: 8:np2010nP ssl

  [March 25, 2015 02:34:21: STAFBASE] SETTING [0]: command execution STAF: staf VTAF_VM POWERON localhost anchor 192.168.49.168:root vm 'vtafVM1_192.168.49.168_4740' WAITFORTOOLS N

  [March 25, 2015 02:34:23: STAFBASE] SETTING [0]: command execution STAF: staf VTAF_VM POWERON localhost anchor 192.168.49.168:root vm 'vtafVM1_192.168.49.168_4740' WAITFORTOOLS N

  [March 25, 2015 02:34:23: STAFBASE] [0] FRAMEWORK: RC:7149

  [March 25, 2015 02:34:23: MULTITECH] [0] FRAME: called VTAF::TestLib:Sphere:Lib: STAFSDK::HostSystem: PowerOnListVMs (password = "np2010nP" user name = 'root' VMNames ='vtafVM1_192.168.49. ) 168_4740, vtafVM1_192.168.49. 168_4740 'HostName ='192.168.49.168 ') returns "RC: 7149 ErrDesc: VM is in an invalid POWER State for operation: ErrMsg: VM is in an invalid POWER State for operation: receiving Exception: com.vmware.qa.staf.common. " EOperationFailed Trace: com.vmware.qa.staf.vc.vm. STAFVirtualMachine. checkAllowedCurrentPowerState (STAFVirtualMachine.java:1774) # com.vmware.qa.staf.vc.vm. STAFVirtualMachine.powerOn (STAFVirtualMachine.java:394) # com.vmware.qa.staf.vc.vm. VMSTAFService.handlePowerOn (VMSTAFService.java:4194) # com.vmware.qa.staf.vc.vm. VMSTAFService.acceptRequest (VMSTAFService.java:470) # '

  [March 25, 2015 02:34:23: TESTHASH] [0] ERROR: cannot run processSetup for configuration: cannot run handleHostVMObj for configuration: RC: 7149 ErrDesc: VM is in an invalid POWER State for operation: ErrMsg: VM is in an invalid POWER State for operation: receiving Exception: com.vmware.qa.staf.common. EOperationFailed Trace: com.vmware.qa.staf.vc.vm. STAFVirtualMachine. checkAllowedCurrentPowerState (STAFVirtualMachine.java:1774) # com.vmware.qa.staf.vc.vm. STAFVirtualMachine.powerOn (STAFVirtualMachine.java:394) # com.vmware.qa.staf.vc.vm. VMSTAFService.handlePowerOn (VMSTAFService.java:4194) # com.vmware.qa.staf.vc.vm. VMSTAFService.acceptRequest (VMSTAFService.java:470) #

  [March 25, 2015 02:34:23: TESTHASH] WARN [0]: found objects that need to be cleaned

  [March 25, 2015 02:34:23: VIRTUALMAC] [0] INFO: cleaning of the VM: vtafVM1_192.168.49.168_4740

  [March 25, 2015 02:34:23: VIRTUALMAC] [0] DEBUG: PowerOffVM() method called

  I fixed it by name NIC different setting on the host and to the. If I put the test both network adapters on the host and the slot the same name, for example, the two vmnic4, starting the virtual computer fails; If I put one like vmnic4 and the other as vmnic5, the virtual machine starts ok.

  I think it should be a bug in the combination of test IOVP NIC.

• WiFi does not work if the SSID is not broadcast by router

  I have a new 55HX929 and tried to connect to my wifi with its built-in wireless adapter. I do not broadcast my network SSID the router for security and privacy. The searched TV network, does not, and then it asks to enter the SSID. Then, it saves the information and trying to connect but fails. If I enable SSID broadcast on the router and then the tv connects fine but I don't have to do. My tivo with its usb wireless adapter works fine with the SSID broadcasts do not when I configure the network settings. On the same stand as the TV with the power of the signal fine. I am currently using a wireless connected to the ethernet jack TV bridge to work around the problem, but it's a waste when the tv should work with a standard network configuration.

  Reading sortiesdvd.com, people have the same problem with NX720 and Sony Google Internet tv. So it seems to be a common problem with Sony games.

  I tried online support chat, and they were not able to help. Everything they told me to do was reset the router and tv which does not help. I don't think they understood that a SSID came from how they responded to my questions.

  Can we get a fix for this?

  Thank you for your messages. We have forwarded your comments to Sony engineering for future updates.

• WG102 fails with iPad / iPhone with iOS 6 and WPA2 / AES - urgent correction necessary!

  Hello *.
  *
  After upgrading my iPad to iOS 3 6 he constantly fails to connect to WiFi with WPA2 and AES - hidden or broadcast SSID - at home and at work because the device does not accept the WPA2 password. This is also the case for my iPhone 4s, but the two appliances worked with WiFi (WPA2 / AES) perfectly with previously installed iOS 5.1.1.
  *
  I tried to downgrade to iOS 5.1.1 but it seems to be is no longer possible to downgrade the two iPad 3 and iPhone 4S as certification and maybe the viewport for iOS 5.1.1 was closed by Apple.

  Strange behaviour seems to address a problem of firmware of the installed Netgear WG 102 APs that all do not allow the connection of iOS 6 devices with WPA2 / AES enabled :-(

  Does anyone know about a possible solution to connect to WiFi with WPA2 and AES with 3 iPad / iPhone 4 and iOS 6 update for Netgear WG 102 APs?
  *
  Thanks a lot for any help and advice.
  *
  Best regards from the Germany
  *
  Matthias

  The downgrade to 5.0.1 works. He fixed a connectivity with my two devices IOS 6, my wife 5 iPhone and my new retinal screen of the iPad. It does not appear to have caused problems of connectivity with other devices down to 5.0.1

• PS B110a - wireless configuration will fail if the network has multiple access points

  Photosmart B110a (CN245B) wireless AIO printer.

  I have several wireless access points using the same SSID to provide coverage over a large area. When you install the printer on the screen TouchSmart wireless installation fails. Print report reveals the following error:

  "More than one access point/router wireless was found which matches your network name (SSID). If this is not intended, your HP printer can connect to the wrong network. »

  In my case this IS planned but there seem to be no available option to answer "OK, just connect to any point of access by using my SSID.  If I turn off all but one the APs configuration complete OK. If I have to do every time I turn on the printer the printer is USELESS for me.

  Did I miss something?

  sijomi

  This should not be a problem.  I have a B110 (and another 10 or so HP wireless printers) on a network of airports with 5 access points and they just connect.

  Here are a few suggestions:

  1. don't use WEP - use WPA or WPA2 with a 13 + character password.

  2. enable the SSID broadcast on all access points

  3. do not use the MAC filtering acddress

  4. make sure "AP isolation" or "isolated wireless" is disabled.

  5. make sure that you are not on a private network, virtual, or connected to your network of comments.

  6. If different strings on access points do not work, try the same channel.

• Windows update fails error Code 800F020B Hauppauge Computer Works WinTV HVR - 950 a ATSC/QAM valve

  Device Capture of Hauppauge Compuer Works, Inc. - Streaming Media and broadcast devices - WinTV HVR - 950q ATSC/QAM

  Installation date: 01/08/2009-10:55 (on build 7100 Windows 7 RTM)

  You may have to restart your computer for this update is taken into account.  (not restarted, update optional removed, the equipment does not work)

  Installation status: failed

  Error details: Code 800F020B

  Undate type: Optional

  Release of updated software Hauppauge Computer Works, Inc. Streaming Media and Drvices released in May 2009

  More information:
  http://winqual.Microsoft.com/support/?DriverID=20283357 (content is set to null, only placeholder)

  Help and Support:
  http://support.Microsoft.com/Select/?Target=Hub (how I arrived here to connect the update failed)

  Made repeated attempts with HVR-950 a device plugged upward, not blocked, etc.  Still didn't update installation.  Finally did me not able to not try again, no uninstall process defined in the current detail informaiton failture.

  Hello GrayWin7,

  Thank you for choosing Microsoft answers forums for Windows Vista. I hope you do well.

  You may need to update the drivers here. Please check the link for more details below:

  http://windowshelp.Microsoft.com/Windows/en-us/help/b293f652-20ed-4D34-af07-f2cba6fe68f51033.mspx

  Alternatively, you can try to perform a clean boot:

  To help resolve the error and other messages, you can start Windows Vista by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  Follow the link for more information below:

  http://support.Microsoft.com/kb/929135

  Hope this information is useful.

  Thank you.

• Linksys E3000 (changed to 199.182.166.168 DNS servers) No. Playstation Network Access

  For a month I got weird pop ups on my IPAD, ANDROID phones, desktop computers AND home. I just thought that I had a bad month and I need to spend more time with my individual devices and get clean them. I then noticed recently, last week I was unable to connect to the Playstation network (NAT Type failed, the Internet connection Test failed). This was happening on my PS3 and PS4. I direct connect of PS4 and PS3 to my Modem cable from Time Warner and I have no problem. Everything works fine. But when connected to wireless or wired to my Linksys e3000... no dice.

  I connect to my router and so some research. I noticed that my DNS servers are 199.182.166.168 and 199.182.166.169. I decided the router and then restart my cable modem. Routers Gets a new address and but there are still some problems with the connection to the network Playstaiton (could be downwards). I noticed that my IP DNS address is different.2xx.xxx.xxx.xxx.  I restore the configuration on the router and DNS goes back to 199.182.166.168.  This is all the information I have at the moment. When I get home tonight I'll have more information.

  Does anyone else have this problem?

  Is the router configured for DNS custom or did you automatically detect DNS of the ISP service and ISP modem?

  What modem to ISP Mfr and model # do you have?

  You could ask the ISP service as well about it. Usually they don't change DNS very often.

  It is recommended to test for other DNS services if you want to use different DNS, you can use this:

  http://www.grc.com/DNS/benchmark.htm

  or http://code.google.com/p/namebench/

• No info from internet provider to my E3000 router from a bridged walkway to Arris T268G

  I am a customer of Comcast and had my gateway Arris T268G filled so that I could use my E3000 router for a wireless/wired network. My configuration is: on the bridge in bridge at the entrance to the internet of my E3000 then the cable coming out at my SE2500 Ethernet switch which I then cable to my PC to the cable connection. No internet. My wireless router is broadcasting because I'm picking up signal but no internet connection. Looking at the dashboard of the E3000 'Status' tab there is no information for the internet provider. I hit the button refresh and renew the IP button and still nothing.

  (1) is my correct configuration?

  (2) is there a setting I should change to communicate correctly with the T268G gateway (defined in bridged mode)?

  Peyates, it is possible that the IP address of the modem and the router's IP address are both in the same IP range. Change the IP address of the E3000 to, say, 10.10.10.1 before you connect it to the modem. In addition, if the DHCP server on the own modem is enabled, you can configure the E3000 and cascade via LAN to LAN to the modem.

  See this article.

  http://Linksys.custhelp.com/cgi-bin/Linksys.cfg/php/enduser/std_adp.php?p_faqid=3733

• E3000 can support 4 TB drive hard seagate ST4000DM000

  Hello, I got a new drive hard seagate 4 TB ST4000DM000.

  I try to use it on my Ver.1.0.04 E3000 (version 6) thanks to a hard disk USB 3.0 enclosure, but it failed.

  The router nothing posted on the webpage of storage, the pilot are not not in the table of USB storage device.

  so I formatted the drive on my laptop windows 7, of course with TPG and a single partition.

  It is OK on my laptop now, but can still be found by the router.

  Can Linksys pass the E3000, so the router firmware takes in charge the TPG and the new 4 TB harddrive?

  The HARD drive may be too advanced for the E3000. The USB function on this unit has been tested to work only with the 1.5 TB. Here is the complete list of the tested on an E3000 USB devices. An update of the firmware is not likely to be released, either to improve the function of the DEVICE.

  It would probably be best to upgrade your router. Check out EA6300. This last router is equipped with a USB 3.0 port, ideal for your HARD drive.

• How to reuse an E3000 as a wired gigabit switch?

  Hi, I am trying to configure my old e3000 as a wireframe only unmanaged gigabit switch, I disabled the wireless broadcast, is

  It is something else I have to do?.

  Should I enable NAT and RIP? Thanks in advance

  You will need to disable the DHCP server (this essentially disables NAT) and adjust its local / router IP address to fit your network. To have the E3000 function as a wired switch, you must connect to the main router via its LAN port. For more information, refer to the article below. Follow the instructions on the LAN - LAN configuration.

  In waterfall or connect a Linksys router to another router

• Failed to install an optional update due to configuration errors. Errors are now fixed, but cannot find the update to make another attempt.

  I installed Skype and I'm using a webcam Logitech C210. Sound works fine but the person that I want to connect with shows a blank computer screen. I checked the settings on my end and everything seems to work fine, including a short video of me at the bottom right of my screen.

  Microsoft sent an optional update called "Logitech-Communication, hardware device, Streaming Media and Broadcast-Webcam 210". However when I tried to install it failed.
  With the help of Microsoft Help, the problem with the update appeared to be several errors in configuration that have been set.
  However, I was not able to find the answer key updated to try to install it and hopefully the video problem knows my contact.
  My question is basically, how do I find the optional update.
  Thank you.
  
   

  Hello

  You should always get the hardware updates directly from the hardware manufacturer. in this case, Logitech.

  http://www.Logitech.com/support

  See you soon.

• Cannot connect my HP Photosmart c309g-m printer to my Linksys WRT54GC router. "No filtering = FAIL.

  I have problems connecting my HP Photosmart c309g-m to my Linksys WRT54GC router.  The diagnostics report says "no filtering = FAIL" in all my attempts.

  First I had implemented security wireless to the router with a personal WPA2 password.

  Because this does not work, I spent my WPA security, given that the diagnostic report suggests that this is what he actually uses for encryption. This no longer works.

  I double and triple checked the MAC address of the printer in my MAC filtering wireless settings. He was right. However, he didn't always connect.

  Reluctantly, I turned MAC filtering. However, the printer still wouldn't connect.

  Now, I'm out of options. All possible ideas for this problem?

  Here are a few ideas:

  1. check that the SSID is being broadcast.

  2. make sure that DHCP is active.

  3. don't use MAC filtering (it is not a security measure, in any case).

  4 change the channel from router to 11.

• E3000 and E4200 can extend wireless but when snafu disabled DHCP

  Hello

  None of the many posts on the extension of the wireless here really solve my problem (I'm not a tech superstar so I need a little handholding).

  Currently use E3000 as my router.  My House is a wonderfully old brick structure with awesome cast thick walls and cool hardwood floors (Yes, I already drilled twice to drop the Ethernet wiring and run it in my basement to the back of the House to come and connect to a switch where is my office to win 8)  Excellent results.

  Now, I'm going to die just to run the wiring to the front of the House under the said floor so that I can bring it and attach a 2nd router. My sister-in-law gave me (just gave me, you the spirit wouldn't let me pay him!) sound E4200 that she can no longer use a reason any.

  Goal: Best performance for a front of House wireless (my bedroom upstairs and the porch on the main floor, where routers are / will be.)  With the additional router in front of the House I will be finally in a smart cable TV.  I must just have better wireless at the front of the House b/c I do a lot of work here lately.* *.

  1. what router do you recommend using as the main router?

  I tried to configure the e4200 (since the 3000 is already) and following the directions on all workstations. I updated the firmware, so the two routers are underway.  My understanding is that I need to put the 4200 (Router 2 "") in Bridge Mode and

  set on the same channel current wireless router 1 (3000).

  2 should I put the 2.4 and 5 Ghz on separate SSID Router 1?  If so, what do the SSID Router 2?

  3. If Router 2 has a separate SSID or should it be identical to my current network, that is, the Router 1?

  4. I understand that Router 2, you must disable DHCP because Router 1 is that work. BUT whenever I do this, in the process configuration, I can't get connected turn it on to Router 2.  I changed the IP address.   Router 1 is 192.168.1.1 with assignments up to 192.168.1.149.   So I do 2 router 192.168.1.2.   Is this good? I do this, then it restarts, and I connect in 192.168.1.2 "page not found".

  5. the way I go about it is:

  -My Office 8 win (I call him Victor, FYI) is connected via a cable (switch) to 1 (E3000) so LAN router and I use to see what my settings are there (and here I'm typing this post).

  -My Win 7 laptop (Richard, FYI), this is where I work on Router 2 (the E4200).  I have cut all connection without wire, then PC cable to Router 2 and connect to Router 2 and from there.

  That's what I should do? ***

  6. am I correct that Router 2 must be in Bridge mode?  Whatever it is, please teach me - it means I'm setting up to repeat the signal or as a little separate LAN that is connected?  Which is better, in your view, given my objectives, above?  When I'm on 'the extension', it would be ideal to be able to go to the first/main network and send things my printer / PC is there, but I'm willing to put up with less of this in order to get the good signal in my areas of work from the home front.

  Note also that the family and I move and use several devices, so it would be fantastic if me and her husband and son and daughter (think: several tablets, phones, computers laptops, desktops, printers, scanners, blah blah blah in this House - I know, I know a lot more about networks I've always wanted to know!) can just get the signal stronger as we move.

  Thanks for any help you can give and of course I would knew what key information I can be left out. I'm really dying to get up and running.

  Position outside to clear my head, but will be back.

  Thanks again.

  Bonnie in PA

  I recommend using the E4200 as your main router.

  Cascade the E3000 with your LAN E4200 to LAN.

  Cascading 'LAN to LAN' instruction in the link below:

  In waterfall or connect a Linksys router to another router

  Thing to keep in mind when cascading a router:

  1. Change the IP address of the secondary router to something like 192.168.1.254 so its on the same network, but is not in conflict with the main router
  2. Make sure that the DHCP service is disabled on the secondary router
  3. Make sure that nothing is ever connected to the Internet port on the secondary router
  4. Have the different SSID of 2.4 Ghz and 5 GHz
  5. Duplicate configuration on routers wireless, but make them broadcast on different channels or put the chain wireless on 'Auto '.

• E3000 issues with browser utility and connect

  Don't know how I got here, but I can now connect to the E3000 using browser utility. With the help of https://10.x.x.x, shows warning of certificate, and then when the page I continue "Internet Explorer cannot display the webpage".

  It does not work as expected in all other ways.

  Parameters:

  Disabled wireless access to use browser

  Disabled SSID broadcast

  Force SSL connection for browser Utility

  Disabled DHCP (my modem/router ADSL handles DHCP) service

  IP address static 10.x.x.x

  Changed the SSID for both frequencies (not identical but)

  etc, etc.

  Has NOT changed the host hame.

  The last time I used the browser utility (weeks) was to disable the wireless to check something. Reactivated problems wireless, no apparent until today when I tried to access it via the browser utility.

  As I've never run Connect, there is no settings to change, and now it cannot detect the device.

  I guess I'll wait until I have TO change something and do a 30-30-30 reset...

  Well, well, well... I must be lucky sometimes...

  Come to see the thread 'Routers Linksys' not accessible via HTTPS on this forum.

  My problem was defintely caused by the update mentioned Microsft http://support.microsoft.com/kb/2643584

  Took the difficulty he 50824 to dsiable the security update and Lo and behold, can connect to utility browser again!

  so happy that I don't have a 30-30-reset...! \

  Still cannot connect with Firefox, thanks to...

  See you soon,.

  GH