EA4500 FTP server remote access fails with active firewall

I tried to access my drive connected to the USB port of the EA4500 remotely and it didn't until I disabled the firewall SPI IPv4/IPv6 options. If anyone else noticed that? Surely, the firewall must not block the own FTP server on the router!

P.S. A friend with an EA3500 had the same problem.

After the reset, all you need to do is to activate the FTP and uncheck the "block Internet applications anonymous" and it will work.

Speaking from my own experience, it you start to turn things market... and offshore and on... something is finally going to get messed up in the router and ask you to do a hard reset.

Tags: Linksys Routers

Similar Questions

Remote access VPN with ASA 5510 by using the DHCP server

Hello

Can someone please share your knowledge to help me find out why I'm not able to receive an IP address on the remote access VPN connection so that I can get an IP local pool DHCP?

I'm trying to set up remote access VPN with ASA 5510. It works with dhcp local pool but does not seem to work when I tried to use an existing DHCP server. It is tested in an internal network as follows:

!

ASA Version 8.2 (5)

!

interface Ethernet0/1

nameif inside

security-level 100

IP 10.6.0.12 255.255.254.0

!

IP local pool testpool 10.6.240.150 - 10.6.240.159 a mask of 255.255.248.0. (worked with it)

!

Route inside 0.0.0.0 0.0.0.0 10.6.0.1 1

!

Crypto ipsec transform-set esp-3des esp-md5-hmac FirstSet

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

Crypto-map dynamic dyn1 1jeu transform-set FirstSet

dynamic mymap 1 dyn1 ipsec-isakmp crypto map

mymap map crypto inside interface

crypto ISAKMP allow inside

crypto ISAKMP policy 1

preshared authentication

3des encryption

sha hash

Group 2

life 43200

!

VPN-addr-assign aaa

VPN-addr-assign dhcp

!

internal group testgroup strategy

testgroup group policy attributes

DHCP-network-scope 10.6.192.1

enable IPSec-udp

IPSec-udp-port 10000

!

username testlay password * encrypted

!

tunnel-group testgroup type remote access

tunnel-group testgroup General attributes

strategy-group-by default testgroup

DHCP-server 10.6.20.3

testgroup group tunnel ipsec-attributes

pre-shared key *.

!

I got following output when I test connect to the ASA with Cisco VPN client 5.0

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: (4) SA (1) + KE + NUNCIO (10) + ID (5), HDR + VENDO

4024 bytesR copied in 3,41 0 seconds (1341 by(tes/sec) 13) of the SELLER (13) seller (13) + the SELLER (13), as well as the SELLER (13) ++ (0) NONE total length: 853

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, SA payload processing

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, processing ke payload

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ISA_KE

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, nonce payload processing

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing ID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received xauth V6 VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, DPD received VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received Fragmentation VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, IKE Peer included IKE fragmentation capability flags: Main Mode: real aggressive Mode: false

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, received NAT-Traversal worm 02 VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: IP = 10.15.200.108, the customer has received Cisco Unity VID

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, connection landed on tunnel_group testgroup

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA payload processing

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, IKE SA proposal # 1, turn # 9 entry overall IKE acceptable matches # 1

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build the payloads of ISAKMP security

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building ke payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building nonce payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, Generating keys for answering machine...

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of payload ID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of Cisco Unity VID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing payload V6 VID xauth

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, building dpd vid payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, constructing the payload of the NAT-Traversal VID ver 02

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, NAT-discovery payload construction

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, construction of Fragmentation VID + load useful functionality

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads VID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, send Altiga/Cisco VPN3000/Cisco ASA GW VID

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 0) with payloads: HDR SA (1) KE (4) NUNCIO (10) + ID (5) + HASH (8) + SELLER (13) + the SELLER (13) + the SELLER (13) + the SELLER (13) NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) total length: 440

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 0) with payloads: HDR + HASH (8) + NOTIFY (11) + NAT - D (130) + NAT - D (130) of the SELLER (13) + the seller (13) + NONE (0) overall length: 168

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing hash payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash for ISAKMP

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, processing notify payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload NAT-discovery of treatment

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, calculation of hash discovered NAT

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, useful treatment IOS/PIX Vendor ID (version: 1.0.0 capabilities: 00000408)

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, payload processing VID

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, the customer has received Cisco Unity VID

Jan 16 15:39:21 [IKEv1]: Group = testgroup, I

[OK]

KenS-mgmt-012 # P = 10.15.200.108, status of automatic NAT detection: remote end is NOT behind a NAT device this end is NOT behind a NAT device

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, empty building hash payload

Jan 16 15:39:21 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, build payloads of hash qm

Jan 16 15:39:21 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 72

Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = d4ca48e4) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 87

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, process_attr(): enter!

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, IP = 10.15.200.108, transformation MODE_CFG response attributes.

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: primary DNS = authorized

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: secondary DNS = authorized

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized primary WINS

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: = authorized secondary WINS

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Compression IP = disabled

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: Split Tunneling political = disabled

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: setting Proxy browser = no - modify

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKEGetUserAttributes: browser Local Proxy bypass = disable

Jan 16 15:39:26 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, (testlay) the authenticated user.

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm

Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 64

Jan 16 15:39:26 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 6b1b471) with payloads: HDR + HASH (8) + ATTR (14) + NONE (0) overall length: 60

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!

Jan 16 15:39:26 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cfg ACK processing attributes

Jan 16 15:39:27 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = 49ae1bb8) with payloads: HDR + HASH (8) + ATTR (14) + (0) NONE total length: 182

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, process_attr(): enter!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, treatment cfg request attributes

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 address!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the IPV4 network mask!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for DNS server address.

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the address of the WINS server.

Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, transaction mode attribute unhandled received: 5

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the banner!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting save PW!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: receipt of request for default domain name!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for Split-Tunnel list!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for split DNS!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for PFS setting!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Proxy Client browser setting!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the list of backup peer ip - sec!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for setting disconnect from the Client Smartcard Removal!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the Version of the Application.

Jan 16 15:39:27 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, Type of Client: Windows NT Client Application Version: 5.0.07.0440

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for FWTYPE!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: request received for the DHCP for DDNS hostname is: DEC20128!

Jan 16 15:39:27 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, MODE_CFG: application received for the UDP Port!

Jan 16 15:39:32 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.

Jan 16 15:39:37 [IKEv1]: IP = 10.15.200.108, IKE_DECODE RECEIPT Message (msgid = b04e830f) with payloads: HDR + HASH (8) + NOTIFY (11) + (0) NONE total length: 84

Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing hash payload

Jan 16 15:39:37 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, processing notify payload

Jan 16 15:39:37 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, in double Phase 2 detected packets. No last packet retransmit.

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE has received the response from type [] at the request of the utility of IP address

Jan 16 15:39:39 [IKEv1]: Group = testgroup, Username = testlay, IP = 10.15.200.108, cannot get an IP address for the remote peer

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE TM V6 WSF (struct & 0xd8030048) , : TM_DONE, EV_ERROR--> TM_BLD_REPLY, EV_IP_FAIL--> TM_BLD_REPLY NullEvent--> TM_BLD_REPLY, EV_GET_IP--> TM_BLD_REPLY, EV_NEED_IP--> TM_WAIT_REQ, EV_PROC_MSG--> TM_WAIT_REQ, EV_HASH_OK--> TM_WAIT_REQ, NullEvent

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, case of mistaken IKE AM Responder WSF (struct & 0xd82b6740) , : AM_DONE, EV_ERROR--> AM_TM_INIT_MODECFG_V6H, EV_TM_FAIL--> AM_TM_INIT_MODECFG_V6H NullEvent--> AM_TM_INIT_MODECFG, EV_WAIT--> AM_TM_INIT_XAUTH_V6H, EV_CHECK_QM_MSG--> AM_TM_INIT_XAUTH_V6H, EV_TM_XAUTH_OK--> AM_TM_INIT_XAUTH_V6H NullEvent--> AM_TM_INIT_XAUTH_V6H, EV_ACTIVATE_NEW_SA

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, IKE SA AM:bd3a9a4b ending: 0x0945c001, refcnt flags 0, tuncnt 0

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, sending clear/delete with the message of reason

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, empty building hash payload

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, constructing the payload to delete IKE

Jan 16 15:39:39 [IKEv1 DEBUG]: Group = testgroup, Username = testlay, IP = 10.15.200.108, build payloads of hash qm

Jan 16 15:39:39 [IKEv1]: IP = 10.15.200.108, IKE_DECODE SEND Message (msgid = 9de30522) with payloads: HDR HASH (8) + DELETE (12) + (0) NONE total length: 80

Kind regards

Lay

For the RADIUS, you need a definition of server-aaa:

Protocol AAA - NPS RADIUS server RADIUS

AAA-server RADIUS NPS (inside) host 10.10.18.12

key *.

authentication port 1812

accounting-port 1813

and tell your tunnel-group for this server:

General-attributes of VPN Tunnel-group

Group-NPS LOCAL RADIUS authentication server

--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni

Update of security for sql server sp3 KB94981 fails with error 2B 33

Each update for SQL Server 2005 on my computer Vista Home Premuim fails. The most recent example is:

Update of security for sql server sp3 KB94981 fails with error 2B 33

for SP2, it was

Security for sql server sp2 KB960089 update fails with error 6AA

Other updates have been ad are successful, although I found out recently that it is the recovery disc option to create under maintenance contract. I fdound the recdisk.exe file, but running it does nothing.

Mike

Maybe check this forum:

SQL Installation of Server & upgrade
http://social.msdn.Microsoft.com/forums/en-us/sqlsetupandupgrade/threads/

TaurArian [MVP] 2005-2010 - Update Services

I noticed that my remote access has been activated twice in a week but I did not. no way to verify when, what, who activated via the event log,...?

I noticed that my remote access has been activated twice in a week but I did not. no way to verify when, what, who activated via the event log,...?

Hi dewthisnow,

The information office for remote access must be in the security log.

For more information, see:

To disable remote desktop

To view the logs in Event Viewer, see:

Using the event viewer

Procedure to view and manage event logs in Event Viewer in Windows XP

VPN (remote access, ASA5520) with 2 clients, one with Internet and other without Internet

Hello! I make a VPN with two clients, using the ASA5520 United Nations. Now I have to do what the customer has internet and the other does not. I can do using ACL? How?

The configuration is:

interface GigabitEthernet0/0

nameif outside

security-level 0

IP 172.16.31.252 255.255.255.248

interface GigabitEthernet0/1

nameif inside

security-level 100

IP 172.16.1.237 255.255.255.240

Access extensive list ip 172.16.1.224 ACLnonat allow 255.255.255.240 host 172.16.1.230

Standard access list Split_tunnel allow 172.16.1.224 255.255.255.240

IP local pool testpool 172.16.1.230 - 172.16.1.232 mask 255.255.255.240

NAT (inside) 0-list of access ACLnonat

Route outside 0.0.0.0 0.0.0.0 172.16.31.254 1

Crypto ipsec transform-set esp-3des esp-md5-hmac hw_trans

life crypto ipsec security association seconds 28800

Crypto ipsec kilobytes of life - safety 4608000 association

Crypto dynamic-map dyn_map 1 transform-set hw_trans

Crypto dynamic-map dyn_map 1 the value reverse-road

stat_map 10000 card crypto ipsec-isakmp dynamic dyn_map

stat_map interface card crypto outside

crypto ISAKMP allow outside

crypto ISAKMP policy 10

preshared authentication

3des encryption

sha hash

Group 2

life 3600

Crypto isakmp nat-traversal 30

internal hw_policy group policy

attributes of the strategy of group hw_policy

value of server DNS 193.205.160.3

Split-tunnel-policy tunnelspecified

value of Split-tunnel-network-list Split_tunnel

Split-dns value 193.205.160.3

username User1 encrypted password privilege 0 pqA3EDHB1cfLxwWn

password username User2 FIQ1c02tX8lU1wHJ encrypted privilege 0

attributes of user User2 name

VPN-framed-ip-address 172.16.1.233 255.255.255.240

allow password-storage

type tunnel-group hwclients remote access

tunnel-group hwclients General-attributes

address testpool pool

Group Policy - by default-hw_policy

hwclients group of tunnel ipsec-attributes

pre-shared key *.

ISAKMP retry threshold 30 keepalive 5

Thanks in advance.

Hello Jose,.

I see that you use LOCAL authentication, what you can do is, you can create another political group and link this political group for the user name, example:

attributes of group PALLET policy

Split-tunnel-policy tunnelall

name of User1 user attributes

RANGE of VPN-group-policy

The other username will use hw_policy, since it is the default value for the tunnel-group hwclients.

HTH

AMatahen

View security server - remote access

We seek to deploy the view. Our security team has some concerns using the view security gateway. Hey im running a windows device and its compromises and someone has remote access to it. Launch the client discovers that someone can see what im doing in the poster session?
If we were to go down the road of SSL VPN, we could disable the split tunneling, and that should take care of the question but I'd like to be able to use PCoIP. Any input would be greatly appreciated. Thank you!

Have not heard this concern before but I think it boils down to what you hear with access remotely.

If the remote access means that someone managed to install a VNC server on your client, and then connect to the server while you are on the view Session then Yes, it would be able to see what you're doing.

If remote access means drop one level then no.

You can still use PCoIP with a VPN client, if that is your main concern.

Linjo

ASA to remote access VPN with external IP dynamic

Hi forum,

I was wondering if it was possible to set up an ASA to provide access to remote connections VPN (IPSEC or WebVPN/SSL) of the outside world, if the external IP address is dynamic (i.e. obtained through DHCP)? I understand how to use DynamicDNS to provide a host name for the VPN clients, I ask simply if the SAA can be configured to allow VPN connections from a DHCP interface addressed. I understand there are problems with the site to site VPN when both sides are addressed in a dynamic way, but it seems that the remote VPN access should work. Just hoping to confirm this before I go and I'm working on a config.

Thanks in advance...

The same configuration applies.

In my view, that the only difference is that with the external IP being dynamic:

interface e0/0

IP address dhcp setroute

crypto map

The only difference is that (the PCF file) VPN clients should have the VPN connection with a hostname (rather than an IP address) and the IP must be solved at the IPs of the SAA.

I'll try to find you an example configuration if you do not.

Federico.

Remote Access connects with shared connection, but when I connect the Ethernet to the box Belkin Wireless cable, there is no network connection

I have dial-up internet. I have to computers. A PC running XP and a laptop that is running Windows 7.
I have the connection shared, if I plug the Ethernet cable to the laptop, it will connect to the internet. I just bought a Belkin G wireless router.
I want to know how to configure it, then the router Belkin Wireless put the switched signal shared wireless. I know it's possible, I'm not sure what I'm doing wrong. It is constantly with him saying on the phone "the DNS server does not respond.

Connect the Ethernet cable from your PC to the WAN (Internet) port on the wireless router. Do not connect to one of the router's LAN ports. Boulder computer Maven
Most Microsoft Valuable Professional

5.0 VMware Server 2012 P2V fails with BSOD

Someone at - it successful Windows Server 2012 with VMware 5.0 installation? I have not tried since an ISO, but when I tried a P2V server restarts periodically and says then there is a problem and that I should look for more information on the 'system thread unhandled exception (winhv.sys)' error as it collects more information!
Thank you
Mark

Construction 623860 is ESXi 5.0 Update 1, so it's ok. You can find an overview of the large version/construction at http://vsphere-land.com/vinfo/release-build-info

Roles that are installed in the system Windows 2012 (Hyper-V,...)?

BTW. the converted virtual computer runs on a virtual IDE drive. During the conversion of a physical system, you must always set the type of appropriate ("LSI Logic SAS controller" in this case) in the Converter Wizard.

André

Cannot install the update on server 2012R2 Manager - fails with Visual Studio 2005 error.

I searched google, tried everything I can find online and you simply cannot install Update Manager on the server 2012R2.
Yes, .NET 3.5 and 4.5 are installed. Am I missing something here?

Extract you the vCenter all server, or that the file Update Manager installation image? If you check out the picture of the installation, please do and launch the installation of the update from the appropriate subdirectory Manager.

André

RV082 and Windows 7, no internet connection with active firewall

Hello

I have a 1.3.98 - tm firmware RV082 and have recently upgraded several Machines to glass & RC for testing, but they can't access the internet.

They can access all the other mahcines internal, but cannot ping the router. The first Pc I upgraded was beautiful and accessible to the internet without problem.

The second started Ok but then loses the internet connection. It can access all internal machines and if I reboot it with XP (dual boot) it works fine. He has been an operational machine without problems netowrk for 2 or 3 years. I tried a diffetrn nic card and another cable froma different wall point in case there was a problem that XP could cicumvent and Windows 7 has been more difficult.

Now the second PC has started doing the same thing and wont connect to internet.

If I disable the firewall on the RV082 Windows 7 PC connect correctly. Can I wathc the tray icon of system on the State of PC modification simply chagnign the status of the firewall on the router.

Occasioanlly a PC will continue to work for a short period before losing internet again or blocked him. I have checkled newspapers and others are no entries in the standard newspaper.

I bypassed Vista Batteux ther so a setting or something I need to change on the window smachines, but as I have Windows 7 on test in withotu the Council to clarify a problem and my two lapotps and have connected through various cafes, Internet etc. even in Spain and Brazil without problem I tend to think it's a problem with the RV082.

Any ideas would be helpful?

Thank you

Kevin

All specifications are as follows, I tried you understand all of the same information if some irrelevant1 may be:

No antivirus on the PC yet!

IBM PC with 4 GB of RAM, pnetium 3.06, 80 GB hdd 2 partitions dual boot Windows XP and Windows 7 Ip static (but tests with DHCP as well) 10.1.2.13 - 2 3com 3cT 1000 + cards internal network - REaltek 10/100 (disabled)

IP 10.1.2.13 void 255.255.255.0 Gateway 10.1.2.1 dns 222.222.222.14

Reference Dell GX520 with 1 GB of RAM 80 GB drive hard new installation Windows 7 dhcp

RV082 LAN 10.1.2.1 sub 255.255.255 DHCP issue. In theory irrelevant, but there are 3 VPN tunnels to the 10.1.3.0, 10.1.4.0 and 10.1.5.0 networks

WAN1 222.222.222.11 void 255.255.255.248 gw 222.222.222.14 dns 222.222.222.14

WAN2 disabled/empty

Loads of transfer App for phone system Avaya, RDP, HTTP, HTTPS, FTP, TFTP, SMTP, POP3, Netware etc etc etc.

IP 222.222.222.14 is a 3com office connect ADSL router

LAN 222.222.222.14 sub 255.255.255.248

WAN DHCP of BT ADSL

222.222.222 ip addresses have been changed for safety!

This set up was valid for 2 or 3 years without problems

Hey Kevin,

To clarify, we have not heard of this I didn't think (I am curious as well), did this start happening when you upgraded the computers?

Its sounds like it from what I've read, and also you can generate by activating and deactivating the FW on request, but this didn't happen until you have changed the PC SW?

If it does, then, looks like soemthing SW PC made and maybe you can endure a wireshark trace and try to sniff which continues when the PC tries to access the internet. I'm not asking to review track, only that it can help you. If you feel like it is a defect of the Cisco product, you can open a folder with the Small Business Support Center and they will watch the track with you.

Steve DiStefano

IS

Sales Channel field in the United States

remote access to manage the Firewall works not

I can't connect remotely ASDM, works very well on the management port. I can't either SSH remote for ASA.

I have a VPN IPSEC of L2L with a SonicWall working to the 192.168.1.0 subnet. It connects on the external interface.

I work SSL VPN AnyConnect. Remote users connect their browser to the external interface, click AnyConnect and are directed to their subnet by a bookmark.

I can connect to the external interface with a VPN IPSEC client and then use SSH to manage my switches in the demilitarized zone and inside.

On the spot, I can manage the firewall traversing when directly connected to the management interface. (Console works too).

But I can't remotely manage the SAA itself! My config is attached. Any help will be appreciated!

Hello

Since you have the 'management-access to inside' command configured, you will need to connect inside the IP interface when you access the device through a virtual private network, rather than the external IP address. However, you are also in the bug following in 8.4 (2):

CSCtr16184 - To-the-box traffic switches vpn hosts after upgrade to 8.4.2

To fix, you must add the keyword 'search route' at the end of the following NAT rules (anything that overlaps your inside interface subnet):
```
nat (inside,any) source static obj-172.16.0.0 obj-172.16.0.0 destination static
obj-192.168.1.0 obj-192.168.1.0 no-proxy-arp route-lookup
nat (inside,any) source static obj-172.16.0.0 obj-172.16.0.0 destination static
obj-172.16.32.0 obj-172.16.32.0 no-proxy-arp route-lookup
nat (inside,any) source static DM_INLINE_NETWORK_2 DM_INLINE_NETWORK_2 destination static obj-192.168.1.0 obj-192.168.1.0 no-proxy-arp route-lookup
```
Hope that helps.

-Mike

Windows home server 2011 - remote access error - wrong password or account to GoDaddy

My windows Home server remote access does not recognize the domain, I've implemented into Go Daddy.

The login and the password are considered bad by the wizard.

Of course I can access with login and password to godaddy.com and everything is nominal.

I noticed the problem 4 weeks ago. No solution has worked so far.

I tried even to remove the entry in the register (via REGEDIT), I found a link to that in the past. But the problem remains.

I fear that some change was introduced on the way the security part

Hello

I suggest you post your query on the TechNet forums to get help. Consult the following link:

https://social.technet.Microsoft.com/forums/WindowsServer/en-us/ba0d1c89-ad59-414a-bf00-d3085a9f25d9/Windows-Home-Server-2011?Forum

It will be useful.

Problem with remote access VPN

Hello

I installed a remote access VPN on my firewall ASA5505 via the ASDM Assistant.

I can successfully connect with the Cisco VPN client. My firewall also shows me the VPN session and shows the Rx packets. However, Tx packets remain 0, so no traffic is getting out. My ASA5505 is configured as a router on a stick with 25 different VLAN. I want to restrict traffic to one VLAN specific using a card encryption.

When I run a command to ping t on my connected Windows box, the firewall log shows me the following message:

"Unable to find political IKE initiator: outside Intf, Src: 10.7.11.18, Dst: ' 172.16.1.1

"This message indicates that the fast path IPSec processing a packet that triggered of IKE, but IKE policy research has failed. This error could be associated calendar. The ACL triggering IKE could have been deleted before IKE has processed the request for initiation. "This problem will likely correct itself."

Unfortunately, the problem is correct.

The "sh cry isa his" and "sh cry ips its ' commands show the following output:

2 IKE peers: 62.140.137.99

Type: user role: answering machine

Generate a new key: no State: AM_ACTIVE

Interface: outside

Tag crypto map: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: 85.17.xxx.xxx (outside interface IP)

local ident (addr, mask, prot, port): (0.0.0.0/0.0.0.0/0/0)

Remote ident (addr, mask, prot, port): (172.16.1.1/255.255.255.255/0/0)

current_peer: 62.140.137.99, username: eclipsevpn

dynamic allocated peer ip: 172.16.1.1

#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

#pkts decaps: 4351, #pkts decrypt: 4351, #pkts check: 4351

compressed #pkts: 0, unzipped #pkts: 0

#pkts uncompressed: 0, comp #pkts failed: 0, #pkts Dang failed: 0

success #frag before: 0, failures before #frag: 0, #fragments created: 0

Sent #PMTUs: 0, #PMTUs rcvd: 0, reassembly: 20th century / of frgs #decapsulated: 0

#send errors: 0, #recv errors: 0

local crypto endpt. : 85.17.xxx.xxx/4500, remote Start crypto. : 62.140.137.99/3698

Path mtu 1500, fresh ipsec generals 82, media, mtu 1500

current outbound SPI: B3D60F71

current inbound SPI: B89BA14A

SAS of the esp on arrival:

SPI: 0xB89BA14A (3097207114)

transform: aes - esp esp-sha-hmac no compression

running parameters = {RA, Tunnel, NAT-T program,}

slot: 0, id_conn: 196608, crypto-card: SYSTEM_DEFAULT_CRYPTO_MAP

calendar of his: service life remaining key (s): 25126

Size IV: 16 bytes

support for replay detection: Y

Anti-replay bitmap:

0xFFE1FFF8 0xFFFFFFFF

outgoing esp sas:

SPI: 0xB3D60F71 (3017150321)

transform: aes - esp esp-sha-hmac no compression

running parameters = {RA, Tunnel, NAT-T program,}

slot: 0, id_conn: 196608, crypto-card: SYSTEM_DEFAULT_CRYPTO_MAP

calendar of his: service life remaining key (s): 25126

Size IV: 16 bytes

support for replay detection: Y

Anti-replay bitmap:

0x00000000 0x00000001

I really have no idea what's going on. I installed a remote access VPN countless times, but this time it shows me the error as described above.

Hi Martijn,

just a few quick thoughts:

-is your ok NAT exemption, i.e. ensure that the return traffic is not NAT' ed.

-Make sure that there is no overlap crypto ACL

-When connected, make a package tracer to see what is happening with the return packages.

for example

packet-tracer in the interface within the icmp 10.7.11.18 0 0 172.16.1.1 detail

(where is the name of the interface on which 10.7.11.18 resides)

This will show you all the steps the rail package in-house (routing, nat, encryption etc.) so it should give you an idea of what is happening, for example when it comes to the bad interface, nat evil rule, wrong entry card crypto etc.

HTH

Herbert

System 32 error (0x00000020): "the process cannot access the file because it is being used by another process.". The operation to open the file will fail with error - 1032 (0xfffffbf8(JET_errFileAccessDenied))"

Original title: svchost (1020)

Event type: error
Event source: ESENT
Event category: general
Event ID: 490
Date: 2010-10-19
Time: 14:51:34
User: n/a
Computer: ROB
Description:
Svchost (1020) an attempt to open the file "C:\WINDOWS\system32\CatRoot2\{127D0A1D-4EF2-11D1-8608-00C04FC295EE}\catdb" for read / write access failed with the error System 32 (0x00000020): "the process cannot access the file because it is being used by another process.". The operation to open the file will fail with error - 1032 (0xfffffbf8(JET_errFileAccessDenied)).

For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

Hi Robrw,

1. when exactly you receive this error?

2. don't you make changes to the computer before this problem?

You can try to rename the catroot2 folder and check if it helps.

Step 1:

a. Click Start and in run type C:\windows\system32 and click ok

b. find the Catroot2 folder. Right-click on Catroot2 and rename it to Catroot2.old

If you are not able to do the normal mode, try to start in safe mode and rename

Check out the link for more information on starting your computer in SafeMode below:

http://support.Microsoft.com/kb/315222

Step 2:

If you are unable to access the catroot2 folder, and then try to change the permissions on the files and check if it helps.

See the following article:

How to capture a file or a folder in Windows XP

http://support.Microsoft.com/kb/308421

Step 3:

You can also try to temporarily disable third-party security software and firewalls and check what is happening.

Note: Activate the security software after the resolution of the problem.

Hope this information is useful.

Jeremy K
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.

If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

EA4500 FTP server remote access fails with active firewall

Similar Questions

Maybe you are looking for