EA7500 Setup with SingTel fiber moden
I just bought a new EA7500 to replace the existing AP router. After installing the internet connection successfully, I noticed that the speed of internet connection wifi to this new router is slower than my old router. What are the configuration settings that I could set to increase speed?
Hi, TK16. You can go into the settings of prioritization of media on your router SmartWifi page, click settings, then set him Off in the WMM support.
Hope the above helps.
Liezl-10104
Linksys technical support
Tags: Linksys Routers
Similar Questions
-
HP 255 G3: I can not enter Setup with administrator password
I can't get into Setup with administrator password
When I go into Setup it gives to enter the administrator password. (I forget)
HP 255 g3
System disabled: 67365449
When asked for the password enter 78043489
REO
-
Problems with connecting fiber and new router AirPort
I installed the fiber optic connection to replace my cable modem connection... I have a network of airport for a long time. When I bridge router ISP in my airport network that there are multiple problems. The major is that when you plug the ethernet cable from the modem ISP Ethernet port on the WAN of Timecapsule port all the TC LAN ports go dead. (the ISP's modem has already a cable ethernet in the WAN port or the first port that comes from the optical network Terminal that the fiber optic cable to connect from the outside). I talked to the ISP and they say just use any ethernet port to connect to the WAN port on the TC. On their end, they say everything is connected and works... then it's the Apple... I bought a new TC and changed my ethernet cables, but all I can establish is a wireless network. My network is itinerant and all of my extremes are connected with cables, but all on my main TC LAN ports are dead. I rebuilt my network and the same problem... And I think that the culprit is ports LAN TC is off
Unfortunately, Apple has designed their routers airport to work with a standard cable and DSL type connections. The fiber is a whole new game ball, and Apple has not yet learned the rules of the game, so you may or may not have a really hard question.
When you plug the ethernet cable from the modem ISP Ethernet port on the WAN of Timecapsule port all the TC LAN ports go dead.
Before you connected to the fiber "modem" Time Capsule, did first reset you back to default settings... and then... set up again I hope to work with the fiber optic router?
If this isn't the case, you need to do whenever you change providers or the modem that the Time Capsule connects to.
All other devices that might be connected to the time Capsule should be turned off and unplugged.
Then, if the time Capsule can be configured to work with the "modem" fiber, you can connect devices to the time Capsule one at a time to ensure that each of them is working before connect you to the other. It may be necessary to reconfigure some or all devices that are connected to the time Capsule so that everything works again.
Bottom line here... get the time Capsule working first with the "to modem" fibers. Then start to add other devices to time Capsule one at a time.
-
Original title: trying to access Wireless Utility Setup with a printer LexMark impact S305 on windows 7, can nybody help me?
lxeapss: error loading DLL communication, I get this pop-up box several times trying to access Wireless Utility Setup with printer. I have tried, defrag, virus scan (vipre), stop, went to the Lexmark Web site to get the latest software downlaod for printer?
Hello
Click on the link below.
http://support.Lexmark.com/index?page=content&ID=so4452&locale=en&UserLocale=en_US
Hope this information helps.
-
DR Setup with ebs 11i &; databases under windows 11.2.0.3
Hello
We have requirements of DR Setup with ebs 11i & 11.2.0.3 database under windows 2003 server 32-bit.
We follow the metalink document
Business continuity for Oracle E-Business Release 11i using Oracle 11 g Release 2 and versions later
Physical Standby Database - Single Instance and Oracle RAC (Doc ID 1068913.1()
But for many windows of missing steps in this document.
If someone made the related activity in windows.
Good to want to share documents through my mail ID: [email protected]
Thanks and greetings
Villi Kumar
Hello
We created the recovery after disaster for 11i ebs in a windows environment.
Now, we are conducting an application and a database shall also.
Once we transition from the primary to the standby, day before the application runs with the new URL.
Therefore, inform our users about the new URL of the application.
Thank you & best regards
Villi Kumar
-
With Photoshop CS6 on my iMac, I got an error message on the Setup with error # 1. He suggested deleting PS CS6 and then re - install. Idid, reinstall using Time Machine. Then, I got the same error message. I recently changed my OS to El Capitan.
Migration of Mac with Time Machine WILL NOT WORK with the Adobe program activations due to hidden registration files
Sign out of your account... Uninstall... to run vacuuming...
-http://helpx.adobe.com/creative-cloud/help/install-apps.html (and uninstall)
-using the vacuuming after uninstalling and prior to the relocation is necessary
-https://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.html
-Restart your computer... Sign in to your account... Reinstall
-
Create Setup with source files
Hello
I have a word search game, and I have a dictionary and the VI create a single file with 'latest scores. " I want to creat installer which indclude these files when im to install in another computer without labview.
Thank you!
First, you must use a project. The project should include all source files and any other files you want to include in your Setup program.
Then, you create a build for an executable specification. Once which is built, make a build for the installer specification. The Setup program must include all components of, OR you may need to run your program (such as the execution engine). You can also specify where to install the files...
-
Wi - Fi protected setup with WRT160Nv2 WAP610N
Hello
What I want to do is extend my network wireless wireless using this access point. I should be able to press the "Wi - Fi Protected Setup" button on both devices to do this, but this doesn't seem to work...
Also, I want to connect my router and wireless n access point but the point of access to customers to be G and N.
# It is not possible. As I mentioned WAP610N isn't a function that connects to a wireless router or connection.
Dual band access point means that any computer with the adapter Wireless 2.4 Ghz or 5 GHz will be able to connect to it. You need a router or access with Repeater function point or an Expander to expand your wireless network.
-
Very slow Windows Vista desktop with optical fiber connection.
Since we moved and got a fiber optic connection, my computer is very slow. We have laptops in the House on windows xp and wireless connections that are not having problems with speed. My computer is directly connected to the modem.
Go to the website of the manufacturer of your Modem > make sure you have the latest Firmware in Vista for it.
Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > look for it last network adapters Vista drivers > download/install the.
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems
Troubleshoot network adapter problems to Microsoft link above.
Try without commitment TCP/IPv6:
If you still have internet connection probs, one thing to try is the separation of the TCP/IPv6 (which is done by going to network connection > right click > properties > it uncheck > OK.)
http://digitalmediaphile.WordPress.com/IPv6-how-to-unbind-from-a-NIC-in-Windows-Vista/
See you soon.
Mick Murphy - Microsoft partner
-
Tips on Setup with 2 blades of Sun and San
Hi all
Can you give me some advice with a new configuration: we lack a POC of VMware view, and we have 2 blades of Sun X 6250. The two are running ESX 3.5U3, but only one is connected to a San.
The first blade runs vCenter and VMware View and virtual machines. The other (connected to the San) runs the virtual desktop (XP)
This configuration is chosen only for budget reasons. We intend to connect to the second blade in the SAN, but it requires a switch of fiber optics and a HBA. But there is no budget for the time ;-(
Each blade has 2 NETWORK interface card and the two are connected. We have created a vSwitch; service console, the computer network, virtual and vmkernel. The two NIC is added to this vSwitch as active to spread the load.
Is it still a requirement for VMotion have a private NETWORK map, or can it be shared?
I thought it was possible to make a VMotion, while a virtual machine is running without shared storage? It is also possible with the vCenter running under VM? It would be nice for the correction.
Any other tips or advice?
Thanks in advance. We appreciate it.
Wouter
Hello
But there is no budget for the time ;-(
We all know that this situation :-D
Each blade has 2 NETWORK interface card and the two are connected. We have created a vSwitch; service console, the computer network, virtual and vmkernel. > Is it still a requirement for VMotion have a private NETWORK card or can it be shared?
It may be shared, but the speed should be 1 GB
I thought it was possible to make a VMotion, while a virtual machine is running without shared storage?
vMotion requires shared storage
It is also possible with the vCenter running under VM? It would be nice for the correction.
Yes vCenter can function as a virtual machine
> Other tips or advice?
Add network cards if you can
You can change the order within the PortGroup when you access EPS
PGs | COS | VMnet | vKernel + vMotion
-
-
HomeKit Setup with OLD Apple ID
I have installed just a few lights Phillips Hue with HomeKit (No Apple TV). Just my iPhone, an echo of the Amazon and the hue of Phillips and Home Apple app.
When I went to share access with Apple ID of my wife, he showed him there was a request from an old account of mine iCloud.com which has not been used over the years and is not in use now. Why it does not recognize my Gmail iCloud account, which is what I am connected to my phone.
Is the iCloud iCloud.com older account in the backend = Gmail account?
Sounds like when you have joined an Apple ID, you did back in the day with a Gmail address, which isn't a big deal. I'm in the same boat and many other institutions.
It can show the Gmail email address as you may be signed in somewhere with him.
To be sure, go here https://appleid.apple.com
-
NAT Setup with a bridged interface possible?
Hello, I have someone ask me if it is possible to configure a Cisco with NAT router for the wireless interface, but no NAT configuration on the fastethernet interfaces.
So when I connect to the radio I get 192.168.1.10 for example 255.255.255.0.
And when I connect to a fastethernet port I will get something like 92.16.235.141 255.255.255.248
Is this possible? Or do I need a sepperate Access Point for that?
I never said that it's a Linksys router. I was talking to a router Cisco (800 series)
But thanks for your help, I've tried it in a test enviremont and it works.
If I set up with a public IP address Vlan1 and Vlan2 with a privat IP this works, but only with one of the latest Cisco IOS images, because a second VLAN cannot do otherwise. I can then add vlan access fastethernet ports.
-
Headset Setup with Windows 7.
Recently, I bought windows 7 and installed it on my PC (before I had XP). My PC is able to run (3.4 GHz, 6 GB 6, ATI 5770). However, I can't get my headphones to work with windows 7. The headset has an orange and a Jack rose. I plugged these sockets on the back of my computer into the corresponding sockets several times but nothing has ever detected by windows. I tried the "Add a device" function and windows came with nothing. Also on audio device manager it says that speakers, headsets and microphones are all not connected, even though they were. Someone knows how to set up with Windows 7?
Also I plugged my old speakers (who has worked with XP) and the same problem occurs. None of these devices have a driver.Hello
Welcome to the microsoft answers site.(A). try to connect a microphone to your computer this way.
After connecting a microphone to a microphone to your computer and turned on Jack (if the microphone has a button), perform the following steps.
1. open Sound by clicking on the Start button, then Control Panel. In the search box, type sound, and then click sound.
2. click on the recording tab, click Microphone, and then click Properties.
3. click the levels tab and make sure that the mute button looks like this. If the button looks like this, click it to turn on sound for this connection, and then click on apply.
4. (optional) to listen to the sounds of the microphone through your speakers or headset, click the listen tab, click on listen this devices check box, and then click OK."Connect one microphone, music player or other audio device to your computer.
http://Windows.Microsoft.com/en-us/Windows7/connect-a-microphone-music-player-or-other-audio-device-to-your-computerB. check the LEDs if it lights when the speakers are plugged.
C. try to connect the headphones to the other location (front) or to a different computer and check.
D. it may be a problem with the slot itself where in the unit is not to be recognized because of the hardware failure.It may be useful
Thanks and greetings
Support Microsoft-dieng
Visit our Microsoft answers feedback Forum and let us know what you think
http://social.answers.Microsoft.com/forums/en-us/answersfeedback/threads/ -
Easy VPN setup with interface to multiples with the same level of security
Hello
I want to configure an ASA 5505 with 7.2 (4) software and dual license ISP and when I configure two interfaces with the level 0 on two security interfaces and enable vpnclient the trace message appear:
ERROR: Cannot determine the internal and external interfaces Easy VPN remote: multiple interfaces with the same levels of security.
vpnlclient of configuration above:
vpnclient Server x.x.x.x where x.x.x.x
vpnclient mode network-extension-mode
vpnclient nem-st-autoconnect
vpnclient TUNNEL_EZVPN_TUNNELSPEC vpngroup password *.
vpnclient username usr_ezvpn_tunnelspec password *.
vpnclient enableinterfaces:
interface Vlan200
nameif outside1
security-level 0
IP x.x.x.x 255.255.255.252
!
interface Vlan300
nameif outside2
security-level 1
IP x.x.x.x 255.255.255.128
!monitor the SLA to the routing:
monitor SLA 100
type echo protocol ipIcmpEcho 200.221.2.45 interface outside1
NUM-package of 5
frequency 30
monitor als 100 calendar life never start-time now
ALS 200 monitor
type echo protocol ipIcmpEcho 200.154.56.80 interface outside2
NUM-package of 5
frequency 30
Annex monitor SLA 200 life never start-time now
ALS 300 monitor
type echo protocol ipIcmpEcho 4.2.2.1 interface outside1
NUM-package of 5
frequency 30
Annex monitor SLA 300 life never start-time now
ALS 400 monitor
type echo protocol ipIcmpEcho 200.244.168.149 interface outside1
NUM-package of 5
Timeout 3000
threshold of 3000
frequency 30
Annex monitor SLA 400 life never start-time nowFollow-up:
!
track 1 rtr 400 accessibility
!
Track 2 rtr 200 accessibility
!routes:
Route 0.0.0.0 outside1 0.0.0.0 x.x.x.x 100 track 1
Route 0.0.0.0 outside2 0.0.0.0 x.x.x.x 200 track 2The track works normal.
Kind regards!
Try using the command "backup interface" on the secondary ISP interface.
http://www.Cisco.com/en/us/docs/security/ASA/asa72/command/reference/b_72.html#wp1338585
You need to increase the level of security to 1 for this interface.
By default, EasyVPN uses the highest level of safety inside and the lowest outside. Anything between the two must be set manually. I assume you have an interior vlan defined but not added to the posted config.
-
vCell Setup with two IP addresses and routing
Hello
My networking team suggested the following configuration:
VLAN-Public: first card network load balancing
VLAN-squatting: second nic load balancer
VLAN-front: first and second nic vCloud Cell01 and even for vCloud Cell02
VLAN-Back: vCenter / ESXi / vShieldMgr / SQL / etc.
Traffic / routing between VLAN-front and back - VLANS are possible.
Now, I installed vCell01 with two network cards, each one IP address: 192.168.1.1 and 192.168.1.11.
vCell02 with two network cards, each one IP address: 192.168.1.2 and 192.168.1.12.
Installation was no problem, connect to SQL went smooth.
But then I noticed that I could not reach 192.168.1.11 since the vCenter Server. Which makes sense, now that I think of it, given that traffic from the vCenter for 192.168.1.11 lights eth1, but due to the default gateway will leave on eth0. And vCenter probably won't like that.
My questions:
-Can I solve this through routing changes to the routing of the vCells table?
-Should I do a complete change in my configuration / network design?
-Should I continue and do not worry vCenter being unable to reach 192.168.1.11.
Advice welcome
PS: Using CentOS 6.5
Concerning
Gabrié
I ran into a similar problem with asymmetric routing when I first set up my vCloud multi-homed cells. In my case, the IP address for each interface was on a different subnet, but the approach is the same for your scenario. You must add that some policy based routing using iproute2 commands rules.
Here's a great article that describes the problem and the solution: http://www.linuxjournal.com/article/7291
For your question, you probably want something like this:
Cell01:
/ sbin/IP flush table 1 road
/ sbin/IP flush table 2 road
/ sbin/IP route add default via
dev eth0 table 1 / sbin/IP route add default via
dev eth1 table 2 / sbin/IP rule add from 192.168.1.1/32 table priority 1 500
/ sbin/IP rule add the priority of 192.168.1.11/32 table 2 600
Cell02:
/ sbin/IP flush table 1 road
/ sbin/IP flush table 2 road
/ sbin/IP route add default via
dev eth0 table 1 / sbin/IP route add default via
dev eth1 table 2 / sbin/IP rule add from 192.168.1.2/32 table priority 1 500
/ sbin/IP rule add the priority of 192.168.1.12/32 table 2 600
Good luck!
Maybe you are looking for
-
Successful HotSync but no information from Palm Desktop.
Wireless Hotsync "completed", but there is no information in my Palm Desktop, no contact, no notes, no tasks, etc., although this information is in the Palm Pilot. I have Windows 7, 64 bit computer laptop. HotSync wireless worked well in the past.
-
I have SD card removed in a way unexpected error on my phone for the last days. Using a Sandisk 16 GB Class 10 UHS1 . Initially, it happened when I opened the game Beach Boom. But later it happened more often and randomly. Because I tried a different
-
T420-best SSD for use in housing Ultrabay caddy?
What is the best SSD for use in the Ultrabay caddy in a Thinkpad T420?
-
Hello, I can't install SP1 on my Toshiba Satellite P205. I tried in vain for two years and decided this week to branch out to help. I have Vista Home Premium and I reset my story was updated following the steps described on by Microsoft support, so
-
Evry time i tryto install adobe flashplayer I get this message: cannot install flash player because winhttp.dll was not found?