Mode of scanning and FPGA

Similar Questions

• Mode of scanning/FPGA for a CRIO by Veristand

  Hello!

  I have a small error using my CRIO 9081 use with CAN communication, here's what I did:

  1. I use the CRIO with scan mode and customized it "Scan engine" and Ethercat for show my analog modules under VeriStand, it's ok

  2. I use the CRIO with FPGA Scan interface (together under Labview) to detect my modules CAN, also ok

  3 - then I wanted to see the CAN and analog modules, so I use this page:

  http://digital.NI.com/public.nsf/allkb/0DB7FEF37C26AF85862575C400531690

  And here's my problem:

  with this method I am able to see the two modules with the custom device 'analytical engine and ethercat", which is really nice, BUT, impossible project VeriStand, the error message asking me to turn the chassis using FPGA, but then I lost the analog module...

  So is it possible to run a project Veristand using both Scan and FPGA interface mode?

  Thank you very much

  Hi Vincent,.

  When you tried to implement, you use the procedure described in the following document in the section use of Scan Engine and EtherCAT with NI 986 x custom device modules XNET ?

  From what I remember, because you use a cRIO-9081, you will need to compile an empty bitfile for your target and place the controller in Mode FPGA hybrid mode on your chassis.

  Could you post a screenshot of the error of deployment, you see?

• Could Scan mode and FPGA mode be used in a project?

  Hi all

  I need a project that the current NI9203 with mode of analysis samples and samples of the accelerometer of the NI 9237 with FPGA mode. It could be achieved? Could Scan mode and FPGA mode be used in a project?

  I use labview2009.

  Thank you very much.

  Yes, they can. This mode is called hybrid mode. To use the Mode of LabVIEW FPGA IO modules, simply slide the module to the target FPGA in the LabVIEW project, disconnected from scan mode. Then use LabVIEW FPGA to program the modules and use I/O variables for read and write I/O on the remaining modules. When you use a LabVIEW FPGA Mode on one or more modules, the logic of the scan Mode CompactRIO on the FPGA, known as the RIO Scan Interface, is compiled in a single application of FPGA with LabVIEW FPGA VI. If no module is configured to use the scan mode, the RIO Scan Interface is not included in the compilation.

• I have win XP SP3, I ran a virus scan and I still can't open anything in the title of the standard account now the admin account does not work no more not even in safe mode what can I do?

  How can I fix the operating system of the issue I'm having with my computer I did a virus scan and now I can't even do anything under the admin account I could do before the scan I can't even do anything in safe mode the standard user account was seen maleware pop ups before I did the scan the admin account had no problem before the scan is carried out I used Mcafee and it did not work it seems to have done worse and windows defender was no use which can make?

  Hello

  • You receive an error message?
  • What exactly are you not able to access?
  "Your question contains all the required information necessary for us to help you. Please re - write your question, this time to ensure that you have included all the information required and we will try to help. »
  Refer to this link for more information on: How to ask a question
   
  In the meantime, you can try a full system scan just to be sure.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

• Document scans and prints in portrait mode, when I record it is in landscape

  HP Office Jet 8600 with a MacBook Air, when I scan a document to a page it scans and prints in portrait mode, but when I save it, it appears like landscape on portrait paper

  It's the solution I found, that it is from Robb92014:

  "Same problem here. The solution is easy - just use preview when you use the HP 8600 to analyze. Just put your documents to be scanned on the charger and the Preview/file/import to officejet pro 8600. A screen then you can only toggle switch various odds & ends, such as PDF and TIFF. Save all scans in a single document; duplex; etc.

  Works easily. »

• Why do I get an error when I try to change the mode of scanning by programming engine?

  Hello

  I have a problem with my EtherCAT system.

  The system contains:

  a RT PXI-8840

  2 position with EtherCAT sensors

  and 8 inverters with EtherCAT (with Softmotion plugin and xml file)

  I use LabVIEW 2015 with RT and FPGA Softmotion module.

  At the beginning of my code I pass the engine scan mode in configuration mode and then the active mode programmatically. It works well when I start my code with LabVIEW but I get an error when I use a startup application. The error code is-2132869095 (the deployment link has expired). I've tried also with a code containing just the screw for the switching of the mode of scan engine and nothing else. With this, I get the same error.

  The problem occurs when one or more inverters are involved in the project.

  Anyone an idea what I need to do to avoid this error?

  Thank you.

  Hello

  the two cases mentioned in my last post have solved the problem. I have to follow this exact sequence and I expect that the analysis engine is running.

  Now, my startup application runs.

• SoftMotion and FPGA OR 9514

  Hey Gang,

  I spent the day to set up a new system of cRIO and a new installation of LV2012 RT and FPGA Softmotion.

  Our system uses a CAN interface, which, we learn, requires the use of FPGA mode.  Maybe this isn't a bad thing, because we are concerned about the speed of the scan mode.  I developed an FPGA application before.

  My main concern is right now, to get the job of control of movement stuff.  Our movement is a NI - 9514.  I hope there is a way to use the SoftMotion modules with the FPGA interface. Otherwise, the movement FPGA examples look REALLY discouraging!

  All I do is homing and simple relative motions.  I enjoy all help/advice on the simple/fast way to get there.

  Thank you!

  Roger

  Hi Roger,

  You can use the 9514 without using the "formidable" examples using the cRIO in hybrid mode. There are good instructions on how to do it here. A quick summary, is to put the modules you want to use in scan mode under the chassis and modules you want to use FPGAS in the FPGA. When you compile the FPGA bitfile, RIO scan interface is compiled for modules that are under the chassis so that you can use in scan mode. A few warnings:

  • The FPGA VI must be running to use the 9514. When you are in scan mode, the FPGA runs automatically without requiring you to do so. However, in hybrid mode, the FPGA does when you run it explicitly.
  • The FPGA VI should work for deploy you the settings of the axis of the target. This can be a bit awkward during development when you make changes to the configuration of the axis. Usually, you run the FPGA VI using the open FPGA VI reference in a RT VI. However, when you run a RT VI, it checks to see if the deployed data are compatible with the project data and if not, invite you to deploy. Don't forget, however, that you cannot deploy your FPGA VI because is not yet running (since it won't work until the open FPGA VI reference runs). When you try to deploy, you will get an error (I think it's something like "E/s Module not found"). What I do usually is during development, run the FPGA VI manually (by pressing the run button). You can then run your VI RT which uses the FPGA VI reference and everything will work. You will encounter this problem only if you change the configuration of the axis of the project (and so won't be a problem for your final application when changing your aern can't axis settings). If you change the configuration of the axis programmatically, you do not experience this problem.

  As a note side for those who use the 951 x modules of movement, unless you really need to do something custom, you must use the modules of 951 x in scan mode. The performance is better in scan mode it is using FPGA (assuming you want to use the API SoftMotion high level (EXVIs, blocks of functions or properties/methods)). When you use FPGA mode, there is further delay to obtain the data of the FPGA in the SoftMotion engine. In addition, you are always coupled to the scan engine! If you get the worst performance, a more difficult experience, and you don't even remove the need for the analytical engine. There are valid reasons to use the modules of 951 x on the FPGA (for example custom control loops), but most applications I've seen use FPGA would be better served by using the module in scan mode.

  Thank you

• cRIO thanks the Module NI 9237 bridge in the Interface of scanning and Anti-Aliasing

  Hello

  I have questions about the use of a Module NI 9237 bridge with CRIO and its use in Scan Interface mode. The manual speaks the data rate of the module, and a (n) parameter that can be set to adjust (to a minimum of 1613 Hz) which in turn puts across the module built in anti-aliasing filters. It seems (but not explicitly stated) that this data rate setting is available FPGA programming mode.

  Our application is currently running in mode Scan Interface, so my question is what is 'throughput' module (and therefore anti-aliasing filters) mode Scan Interface? And, if we have the analysis period the value 10msec (100 Hz), y at - it no filtering of the anti-aliasiing of software provided automatically by scanning interface itself related to the period of scanning? Or all the anti-aliasing extra something that we must build within ourselves? I looked at the example provided with Scan Interface and there is nothing more.

  I don't understand about anti-aliasing, just need to clarify what is happening for this specific module mode Scan Interface.

  Thank you

  Andy

  Hi Andy,.

  I had to have a quick sleep on this night to get my facts right, hope that the delay was too long!

  The minimum data listed in the 1613 samples/s are due to a forumla that uses the internal time base that is fairly well explained on page 20 of the Manual. The sweep period did not affect the rate of data, or to activate the anti-aliasing filter. My previous post was wrong in that sense, apologies!

  This page helps explain mode of scanning pretty well too, but the best way to explain it is that even if the frequency of the module can be attached to 1613 samples/s or higher, the compactRIO will collect only 1,000 of these samples a second, or in your case if you are using a rate of 10ms loop, 100 of these samples of 1613. The anti-aliasing cut will be based on 1613 x 0.45 as you said and so will be 725Hz (not based on the rate of loop as I mentioned incorrectly)

  In this case with these modules it is probably a good idea not to use a period of scanning slower than 1 msec for the reason you said - if you're worried about oversampling you can always you decimate readings in the software afterwards to take each readings from 1 to 10 (this page explains how do with an eerily similar situation!)

• AVG detects viruses, C:\sccfg.sys if I scan and delete, it will appear after each reboot.

  Original title: C:\sccfg.sys

  AVG detects C:\sccfg.sys
  What is a rootkit?
  How can I get rid of it permanently?
  I ask AVG Anti-virus (free) to cope - AVV, then asks me to restart the computer
  After the re - start AVG advises me that the threat has been eliminated.
  AVG analysis finds no problem for the next (approx.) 2-3 weeks
  Then, the threat is detected again.
  I have lived this cycle several times now.
  BUT I want to get rid of the threat for good.

  Internet search suggests this threat comes from a program called "Folder Lock", (which I had installed for several years) but AVG has only been reported as a threat for maybe three months.
  Research on the Internet tells me that the problem cannot be solved by uninstalling "Folder Lock"

  How can I get rid of this threat?

  Hi Leeds,

  It seems that AVG detects C:\sccfg.sys as virus, if you scan and delete, it will appear after each reboot.

  Let's run the virus scan in safe mode with networking:

  Check out this link to start your computer in safe mode with networking:

  A description of the options to boot in Safe Mode Windows XP http://support.microsoft.com/kb/315222

  After starting in safe mode with network, virus using AVG anti-virus scanner.

  With AVG Anti-virus, perform a full scan using the Microsoft Safety Scanner.

  Refer to this link:

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  I hope this helps!

• PSC 1210 all-in-one: hp psc 1210 order copy but scan and print

  Until recently the copied PSC 1210, scanned and printed.  It copies is no longer in black & white, or rather when I press the copy button, the scanning starts and the printer prints a blank page.  Without moving anything, I can scan the document (Windows Fax and Scan) and print it using the same PSC 1210 and it prints perfectly.  A color copy prints a few characters in blue/green.  No recent change in hardware or software (other than the Microsoft updates).

  Hi @will-not-copy,.

  Maybe the problem is related to the ink, especially the black ink. If I understand your description that you can scan and print again, but you are unable to copy. Copying and scanning use the same hardware components so ideally if we work so should the other. Copy and print using the same ink system so if you can print, you should be able to copy; However, the impression of the computer may produce a composite black, which means that the colors combine to make black, when copying the printer can pull out the black cartridge to produce black. That's what I mean when I say that the problem might have something to do with the he black cartridge.

  I would like to print a self-test report to see if the printer hardware can produce black ink in stand-alone mode. To print a report, use the following steps:

  1. Load the plain, white paper into the paper tray.

• On a shared PC my side do not connect to the internet but side not affected spouse. I have run virus scan and none detected on its side but can't run on my side, because I can not connect help please.

  My husband and I share a PC. He has his desk top and I have mine, just that recently, I have not been able to connect to what anyone on my side of the PC, but its East side works well, it can connect to the internet, but I can't any idea what should I do? I ran virus scan and his side of own, cannot check the mine but cannot connect help please.

  Hello

  1. you remember to make changes to your computer, after which the issue started?
  2. do you have a cable or a wireless connection?

  I would recommend that you follow these steps.

  Step 1:

  Test the issue in safe mode with network and check if that helps.

  Step 2:

  Configure the connection to obtain an IP address automatically.
   
  a. click "Start", enter "NCPA. CPL"(without quotes) in the search bar and press"Enter. "
  b. right-click on the network connection, and then click "Properties".
  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  c. click Select 'Protocol Version 6 (TCP/IPv6) Internet' and then click 'properties '.
  d. check "obtain an IP address automatically" and "Obtain DNS server address automatically".
  e. click 'OK '.
  f. click Select 'Protocol Internet Version 4 (TCP/IPv4)' and then click 'properties '.
  g. check "obtain an IP address automatically" and "Obtain DNS server address automatically".
  h. click on 'OK '.

  Step 3:

  Follow the steps in this article and check if that helps.

  Why can't I connect to the Internet?

  Steps are also applicable for Windows Vista.

• This program called spyware protection starts a scan and it won't let me open anything

  original title: spyware

  I'm having a huge problem. I was online and all of a sudden everything closed and this program called spyware protection starts a scan and it won't let me open anything. Programs, media, games anything. The only option he buy or well it won't go away, and let not my computer does. Any ideas on how I can get around the program and just close off the coast and then delete. It also doesn't let me open the the Task Manager or msconfig :(

  I'm having a huge problem. I was online and all of a sudden everything closed and this program called spyware protection starts a scan and it won't let me open anything. Programs, media, games anything. The only option he buy or well it won't go away, and let not my computer does. Any ideas on how I can get around the program and just close off the coast and then delete. It also doesn't let me open the the Task Manager or msconfig :(

  It's Spyware Protection 2010 (uninstall Guide). Follow the step by step instructions.
  http://deletemalware.blogspot.com/2010/10/how-to-remove-spyware-protection-2010.html

  If you are not able to download, then find a friend who owns a computer even in Mode safe mode with networking, download the uninstall Guide > burn to a CD or a flash drive > home and run it on your computer. For the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.

• I get startup repair screen when I try to boot my laptop from dell inspirion windows 7, I run the scan and detects any errors. When I ran repair usb key received the error 0x400110020000100A

  I get startup repair screen when I try to boot my laptop Dell Inspiron windows 7, I run the scan and detects any errors. So, I tried to use a USB repair for a laptop Dell Latitude Windows 7 pro and I still can't the computer to start. Tried to restore to the factory settings, can not. I have no image, backups, all missing, restore points?

  After that I tried to launch the USB repair I got 0x400110020000100A error code and I received error (0x8007027E) indicating the device will not start without a reboot.

  Anyone know how to fix this?

  Any advice would be greatly appreciated. I'm not computer illiterate, but am not pro either. Just use them not program them or even understand all languages!

  ____________________________________________________________________________________________________________

  Dell Inspiron laptop about 4-5 years.

  Running windows 7 Home Edition.

  Does not start little matter what I tried.

  If I remember correctly, I looked in MS-DOS mode and noticed that it said something like "x: win...» "that seemed strange to me because I thought that it should say"c: victory... "but as I said I am not a computer wiz so if anyone can help me, I would appreciate it.

  I'm about to rip the hair off my head with my laptop. My latitude was blue planned, surprisingly I fixed it (don't ask how, you couldn't tell). Then my dell inspiron would not start right after my dell latitude fell out of my truck and landed on the sidewalk, wanted to kill the person, the screen is broken. I can use it but it is very difficult, see a mosquito net and not perfectly clear, works well. lol someone knows somewhere or that would install a new screen for a reasonable price? I live in the Boston area.

  Back to the laptop won't start not, when I ran repair USB key received the error 0x400110020000100A

  Hello

  Thank you for the update on the issue. I appreciate your time and effort in resolving this issue.

  You can try the following methods and check if it helps.

  Method 1:

  You can use the Bootrec.exe tool in the Windows recovery environment (Windows RE) to troubleshoot and repair the following items in Windows Vista or Windows 7:

  • A master boot record (MBR)
  • A boot sector
  • A Boot Configuration data (BCD) store

  Note: When you are troubleshooting startup issues by using the Windows RE, you should first try the Startup Repair option in the System Recovery Options dialog box. If the Startup Repair option does not resolve the problem, or if you must troubleshoot more steps manually, use the Bootrec.exe

  Use the Bootrec.exe tool in the Windows recovery environment to troubleshoot and repair startup issues in Windows

  http://support.Microsoft.com/kb/927392

  If the problem persists, proceed to method 2.

  Method 2:

  Please follow these steps:

  1. Tool command prompt open in the mode of the Windows recovery environment .
  2. You will see X:\Sources
  3. Type chkdsk c:\ at the flashing prompt to launch the utility Chkdsk. replace c:\ with the letter of the drive that you want to run the Chkdsk utility. If the hard drive is d:\, then type that instead.
  4. After the "chkdsk c:\. "insert \f command to fix errors on the disk volume or the \r to recover bad sectors and then press ENTER.
  5. Restart the computer once the chkdsk command has completed.

  Note: Running chkdsk on the drive if bad sectors are found on the hard drive, it attempts to repair this sector, if all available on which data may be lost.

  For more information: Please refer to the section of the additional If you can not boot into Windows at all stages in the following link.

  Resolve stop (blue screen) error in Windows 7

  http://Windows.Microsoft.com/en-in/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  Hope this information is useful. If the problem still persists, please post back for further assistance, we will be happy to help you.

• After scanning essentials security said my computer has not been scanned and it is not protected

  After that says security essentials scan my computer has not been digitized and is not protected. It is on a weekly auto scan and does not work. Why

  Hi Pat,

  Thanks for choosing Windows 8 and welcome to the Community Forums of Microsoft.

  According to the description provided, automatic scanning of Microsoft Security Essentials not happens on your computer.

  1. What is the operating system on your computer?
  2. you use security software?
  3. did you of recent changes to the computer?

  A possible reason for this problem is that you have installed entirely or partially on the PC security software conflict. Remove all other computer security software.

  Method 1:

  
  Uninstall program anti-virus and check if it helps.

  How to uninstall antivirus or antispyware programs?

  http://Windows.Microsoft.com/en-us/Windows/how-do-i-uninstall-antivirus-or-antispyware-programs

  Important: Antivirus software can help protect your computer against viruses and other security threats.

  In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2:

  1. to run, the PC must be on and connected to the internet (it cannot be stopped, "standby mode", hybrid sleep or Hibernate mode)
  2. saving settings must be such that the PC not to close or to go asleep during analysis.
  3 analyses do not begin precisely when demand - some may start earlier or later than the officially set time hour (according to Microsoft servers and charges at the time).

  You can also refer to the article mentioned below for more information.

  Microsoft Security Essentials - Installation Checklist and frequently asked Questions

  http://experts.Windows.com/w/experts_wiki/89.aspx

  If Microsoft Security Essentials problem or if you experience problems of Windows in the future, let us know and we would be happy to help you.

• Scan and repair disk stuck on 27%

  Yes I've seen questions on this subject, but it's a little different.

  I have a laptop HP Envy m6 on Windows 8. He told me before the update to 8.1, I install the updates of Windows 8 remaining. Tried to install, but I get 8000ffff error code. I went in cmd and do the chkdsk command and restarted my laptop. It gets stuck on 27% when it is scanning and repair. Skip the process works, but it just ends up being a black screen instead of take me to the login screen. I tried the Safe Mode with network and still the same problem. All the patches?

  Hello

  Thanks for posting your query on the Microsoft Community.

  According to the description, I understand that you are facing problems with your computer of Windows 8 is it stuck at 27% when scanning and the repair process.

  This could occur due to system conflicts.

  I suggest you refer to the suggestions provided by Rajesh Govind replied on 21 March 2013 and check if this is useful.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_8-performance/PC-stuck-on-boot-scanning-an-repairing-drive-c-28/57677c00-AF01-48b3-A121-c921512d25c1

  I hope this helps. Please let us know the results. We will be happy to help you further.