EDIROL fa101

Similar Questions

• Necesito UN driver para tarjeta sonido Edirol UA 25 24 bit 96 kHz para windows 7Dispositivo

  I need a driver para tarjeta sonido EDIROL UA - 25 24 bit 96 kHz para Windows 7

  Need driver for EDIROL UA - 25 24 bit 96 khz for Windows 7

  Hello

  Please select your language from the drop-down menu above to post your question in the language of your choice. The forum in which you've posted is for English only. If you can't find your language above, support for additional international sites options are by following the link below:

  http://support.Microsoft.com/common/international.aspx

• I can't install edirol ua 20 with windows 8

  I'm looking for drivers for edirol ua 20

  I'm looking for drivers for edirol ua 20

  Hello

  Here is a link to the website of Edirol UA 20.

  UA-20: Products: Roland:
  http://www.Roland.com/products/en/UA-20/

  Concerning

• Audio serious buffering of problems L350 - 20G / FA-66 / Expresscard Firewire

  Hello

  I'm after some advice about this frustrating; I used to have a Toshiba Equium A100 - 02L I used in conjunction with my Edirol FA - 66 firewire audio interface, that I used for about 3 years with no problems. The laptop took a battering to concerts and other things kicking so I decided to upgrade.

  I went for the Satellite L350 - 20G and have tried to get my work with it through the use of am ST LAB Express card double 6-pin firewire port with a TI FA-66 chipset. I tried to use this in XP / Windows 7/Vista with no good result. I have made sure I have all the latest drivers for all platforms and made sure I GL40 chipset driver installed and still the same result audio seems to be severely low resolution or buffers and chops the audio to the top.

  This t really shouldn't happen I don't know, but am pretty out of options. Another comment on the express card slot is the slot is wide like a PCMCIA slot and it does it not very well Express card. I feel a little cheated on this and had a lot of faith in my old Toshiba but now wonder what the hell to do what I bought this laptop for Audio / production.

  All the tips are greatly appreciated.

  As far as I know, and I saw him in textbooks too, while your computer you can use ExpressCard34 or ExpressCard54, both with 26 pins. You can see them HERE.

• Equium A60-152: how to change the IRQ?

  Hello!

  I have an interface audio firewire (Edirol FA-101), who is having a few problems and I think it's to with an IRQ conflict on my laptop Equium A60-152.
  When I looked in the Device Manager, I noticed that my firewire host shares IRQ 19 with several other devices (USB, Cardbus etc.).
  Is it possible that I can move my firewire host so that it runs on a separate IRQ of these other devices?

  I noticed that several numbers are not in use (18, 20, 9-11, 4-7), maybe one of them would be appropriate? Whenever I try to change the IRQ of a device in Device Manager, it is marked as "automatic settings" and I can't change that.

  Thanks for any help you can give me!

  Phil

  Hello

  Usually it s not is not necessary and not advisable to change the IRQS manually.
  The operating system controls all the settings and I guess that all the parameters of this are ok.
  Write you about some problems, but you don t say what s wrong.

  However, it is a 3rd party material and in my opinion, you will have more chance to solve the problem if you contact the manufacture of equipment support.

  Good luck.

  PS: Please also check this site with FAQ about this material:
  http://www.Roland.com/products/en/_SUPPORT/FAQ.cfm?LN=EN&PRD=FA-101&DSP=0&iCncd=491

• Request help second addition, internal hard drive [HP Pavilion Elite e9290f]

  Hello

  Quick question here. I am a music producer and you can always use a ton of extra space as some of my projects are 17 to 20 GB in size. My HP e9290f comes with a stock of 1 TB Seagate (I think) internal hard drive. I intend to add this DeckStar HGST hard 4 TB (7200 RPM)

  However, I am not sure, if this drive is compatible with my computer. I talked about the upgrade & maintenance manual but inside, he tells me only how to replace the current internal hard drive. The addition of this amount of space external hard drive is not an option since all my ports are used by external hard drive! Can anyone shed light on what tools I need exactly to connect this HD extra 4TB? I would appreciate your answers, because time is of the essence

  HP Pavilion Elite e9290f | Intel Core i7 920 2.67 GHz | Windows 7 Ultimate 64 - bit Edition. 20 GB OF DDR3 SDRAM MEMORY | 1 TB of HDD at 7200 RPM. HARD drive external 2 TB | HARD drive 1 external to | HARD drive 640 GB external | HDD external 500 GB | NVIDIA GeForce GTX 260 1.8 GB | Audio interface Edirol FA-101 | Samsung 2493 HM 24 inches. Wide screen monitor |

  Hello

  I have not tested a HDD 4 TB on the motherboard of truckee. In theory, it should work as a data reader set shaped like a GPT disk.

  Another option if you don't want to take the risk is to install two hard drives of 2 TB. The one in the location empty in the cage from the hard drive and another in the optical drive Bay (if open) second.  You will need one 3.5 "to 5.25" adapter if you use the optical Bay.

  Check on the return policy for the 4 TB harddrive and see if your can return/exchange it if it doesn't work.  Kit retail for Hitachi 4TB has an optional driver if the motherboard of your PC will not format the drive completely outside up to 4 TB.

  

• External audio device for Tecra A11 - 11H

  Although the Tecra A11 - 11 sound better than most laptops, I would definitely come back to the full sound quality.
  Without any audio output the possibilities seem very limited.
  USB speakers seem to be either very low powered or high-powered, expensive, or boom-box.

  My daughter, a Windows user, has one of those gadgets
  http://www.cclonline.com/product-info.asp?product_id=57743&TID=gsearch
  with its 5.1 speakers and the result is really good (and I already have the same set of 5.1 speakers, currently unused).
  The problem is of course that Creative do not cooperate with the world of SILK.

  Does anyone know of a similar product that works well with Linux?

  There is in alsa:
  EDIROL UA-1000 and UA - 101
  Tascam USB Audio/MIDI ?
  ? interfaces or controllers US-122, US-224 and US-428
  Native Instruments RigKontrol2 ?
  ? * Native Instruments RigKontrol3 ?
  ? * Native Instruments Kore Controller ?
  ? * Native Instruments Kore Controller 2 ?
  ? * Native Instruments Audio Kontrol 1 ?
  ? * Native Instruments Audio 2 DJ ?
  ? * Native Instruments Audio 4 DJ ?
  ? * Native Instruments Audio 8 DJ ?
  ? * Native Instruments Guitar Rig Session IO?
  ? * Native Instruments Guitar Rig mobile ?
  ? * Native Instruments Traktor Kontrol X 1
  all this must work well...

• Portege R600 - white noise problem

  My Toshiba Portege R600-102 a constant white noise (as you can hear on http://bit.ly/7HaRfn), which becomes apparent when the computer is used with headphones or connected to a speaker.

  This happens with the latest audio drivers under Windows XP and Windows 7.

  The noise does not disappear when I turn off the microphone or disable the onboard sound of the Device Manager.

  In fact, when I connect the laptop to a PA system pro (Edirol UA-101 with Yamaha MSP5) via USB, I get the same noise from Yamaha! That tells me that there is probably a fundamental problem with the motherboard.

  Someone has a similar problem? Or ideas?

  Does this happen with and without mains?

• No digital output on a Satellite P200

  I just bought a Satellite P200 and am trying to put it to the test. Today I tried recording on a digital audio recorder (Edirol R-4) connected to the output digital output jack but can get no signal. I can get a signal from the analog headphone jack.

  I have no problem with digital recording of my desktop PC which has an installed Sound Blaster card so it doesn't seem to be an incompatibility or a problem with the connecting cable.

  I tried to set the default output to digital mode in the setup of REALtek but no difference.

  Any suggestions gratefully received.

  David

  Anyone else had this problem?

  David

• Card support FireWire on Inspiron 660

  I bought your desktop Inspiron 660 with Win 8 (original version, I think) a year or two ago.  Eventually want to use devices USB Audio (sampler Edirol UA-25, helmet DAC etc.) which are not supported by base 8 Win, the cheapest solution was to upgrade to a new version of Win 7 (I got a Dell version) with a new HDD in the desktop.   This arrangement works very well with all my USB audio devices.

  Then, I want to run an audio interface box 4-Channel M-Audio Firewire and Firewire PCI express card to receive from eBay.  It's a 1394, unbranded with chip WB381.  It appears in Device Manager - no reported problems. However the menu sounds in the Panel sees as an available playback or recording device, and the M-Audio box reports also no link.  I tried all three drivers available in Windows 7 for the card, as suggested elsewhere, without success.  M-audio box works OK with Win XP on another computer with a Firewire port that is provided by an OEM, but I don't have any other PC with ports PCI express to test the card...

  This is likely to be a problem of Dell software or a hardware/driver PCI problem.  Maybe I should get a card with a different chipset.  I note, there is a lot of posts related to problems with Firewire and Dell computers.  Are there tests I can run to determine what is happening.

  Thanks in advance

  John

  Windows 8 and 8.1 firewire drivers are laminated.

  The only way to solve this problem is to use a card with Texas Instruments Chipset and copy the LEGACY drivers from a windows machine 7.

  Below are those with chips from Texas Instruments

  MASSCOOL 3 Firewire 1394 ports has 6-pin PCI Express card model PCE-F201 Newegg link link manufacturer Chipset: TI XIO2200A

  SIIG two port FireWire 400 PCI Express x 1 model NN-E20112-S2 Newegg link link manufacturer card Chipset: Texas Instruments

  SYBA PCI - Express 1394 FireWire model SD-PEX-FWB Newegg link link manufacturer Chipset card: TI TSB82AA2

• Problem of latency using MS GS Wavetable Synth

  I'm learning to play piano using a keyboard controller Midi Edirol PCR - 300 connected to my PC via a USB cable and produce sounds using the MS GS Wavetable synth. However, the delay between pushing a button on the keyboard and the sound being heard inside is so long that it is absolutely impossible to use as it is.

  1. Is it possible to decrease the latency?
  2. If not, is there a way to replace with something that is useful, and in this case wavetable synthesizer WHAT?

  As it is, using the keyboard cannot be called 'play' but rather 'musical programming.

  / StaffanB

  Hello

  The Microsoft GS Wavetable SW Synth is a software synthesizer, it adds about 1/10 of a second delay between the time it receives a MIDI note and the time, that the note can be heard through the audio output. This can create problems of synchronization with audio tracks and other MIDI tracks sent to hardware MIDI synths. If your sound card has a hardware MIDI synth, it should be preferred to the Microsoft MIDI synth.

  The desired MIDI outputs can be selected in the dialog box file/settings/preferences/MIDI/MIDI devices. The default is Midi mapper, which corresponds to the MIDI output device selected in the Start Menu/control panel configuration/sounds and audio/Audio device as the default device for 'MIDI-music playback.

  For more information, see this link:

  http://www.pgmusic.com/tutorial_bbwlatency.htm

  http://Forum.cakewalk.com/TM.aspx?m=935347&mpage=1&print=true

  It will be useful.

• The release of Windows 7 MIDI device selection

  I'm an active musician, who has recently made the switch from XP to Windows 7, Vista to jump.  I connected my Edirol UM-1 and drivers installed successfully.  The interface works very well in my DAW software, but I also like having WMP using the UM-1 as the default MIDI output device.  When I went to the control panel to make this choice, I discovered that it lacked the MIDI device section completely.

  There are several threads on this topic in the forums of Vista, but I did find many discussions on this topic in the Windows 7 forum.  The fact that this problem remains of Vista to Windows 7 doesn't give me much hope that a solution will come from Microsoft.

  My questions: is there a solution to this problem that doesn't involve registry or questionable downloads hacks? Or someone had succeeded in Windows 7 using Registry hacks or software patches.

  Hi again well Don I found where you made your mistake! You not change the registry to the right place. You must go to the directory or the DEFAULT folder of MIDI DEVICES. \Default HKEY_CURRENT_USER\Software\Microsoft\ActiveMovie\devenum\ {4EFE2452-168A-11D1-BC76-00C04FB9453B} MidiOut device

  You go to the directory in the same 4EFE2452-168A-11D1-BC76-00C04FB9453B, but you change Tascam US122mk2 and synthesizer Wavetable Microsoft DO NOT EDIT THESE FILES directories. You MUST GO IN THE DEFAULT DIRECTORY of MIDI DEVICE! You should also re edit the device two Tascam and MS WAvetable directories to zero initial for Wavetable and 1 for tascam. Can change the DEFAULT directory of MIDI to zero in the case of edge DEVICES or 1 for USB. A simple mistake that cost you a few follicles ;-)  Terry

• How to set the playback sound

  original title: Audio Question for HP Pavilion

  Hi, I own a HP Pavilion dv6-7138us notebook PC, and I have a question for her. There seems to be a really weird setting during audio playback and it's not fair on iTunes, it's on everything I play on the computer. It produces calm sounds really hard. I hate listening to songs like this because the intros will be really strong and then the rest of the song will be the same volume (which is bad because it usually makes the battery much more silent as they should be, and it's really weird). What is this setting and how can I cancel it? It is clearly in contrast to the "normal" for most computers read mode, I do not like.

  Hello

  Try to uninstall and reinstall the sound card drivers, it has helped me. Try Method 1, provided by Divya R.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/can-not-uninstall-audio-driver-Roland-EDIROL-ua1ex/ed5a9084-ca84-417f-ABEF-8896431d21b0

  All the best!

• Now that we have the support anti surface control in first Pro CC...

  Does anyone know if an older Mackie Control universal (MCU) with just not the USB and MIDI connectors work them with first Pro CC? My soundcard, an Edirol / Roland UA-25EX has a MIDI in and Midi out connectors.

  Thank you

  Mark

  Agency will work with the old model MCU, when it is connected to a midi interface.  The control Surface support will allow transport, fader and control of pepo, with a few predefined buttons.  It works on the clip and the mixer track (but not at the same time).  There is also an option to assignable function keys.  To enable support Makie, go to preferences of management control, click on the Add button and select Mackie in the context menu of device class (the button assignments are located in this window as well).  Then press the settings button, click Add, and then select your midi input and output devices, and then click ok.  Control surface must then be activated for the Mackie.

  Hope that helps,

  Todd