EliteBook 8560w workstation: laptop Freeze at startup

Similar Questions

• laptop freezes on startup

  Hi, I m having hp Pavilion dv5-1110em laptop computer with windows 7 ultimate version 64 bit... in the last week he stop from and freezes at the windows logo but working safe mode, but today the safe mode also freezes at startup when loading the drivers... now I get no option to boot up my laptop I didn't not recovery also disks... Please help

  Yes, I've tried everything...

• HP G62 laptop computer: laptop freezes after startup

  After starting my laptop freezes.  How long after starting varies.  Sometimes it will freeze after only a few minutes. Sometimes it can be operational for an hour or two.  Want to know how to fix this.

  Tested hard drive and the Long DST failed.  Has given an ID of the failure of QAGCHR-5GH847-XDOO3A-61AKO3.  Product ID is XHO66UA #ABA.

  Hello

  Error code 24 characters is a failure of the entire test (DST) disk Self and would indicate that hard is defective and must be replaced.  This is also consistent with the freezing issues you describe.

  If you want a guide on replacing the hard drive yourself, let me know.

  Kind regards

  DP - K

• EliteBook 85602: Howto activate Intel HD Graphics on Elitebook 8560w workstation

  Hello

  I got a 8560w Elitebook which has an Intel Core i7 processor that supports Intel Wireless Display technology. Now, I want to use Intel WiDi for stream to my smart TV via miracast.

  But I can't do it, because only NVidia graphic card is usable. The Intel HD 3000 seems to be disabled. So my question is, is it possible to activate to use it? There is no option in the BIOS.

  Thank you very much

  Kind regards.

  Conclusion: It is not possible.

• EliteBook 8560w: startup stops at the HP logo

  EliteBook 8560w, 8 MB ram, Intel i5 - 2540M to 2.6 Ghz, AMD over-pants M5950

  Computer was working fine without any problems. Windows Update, now stuck on startup with HP logo on the screen and the text "press the ESC key for startup menu '.

  • ESC key does nothing.
  • Removed the battery, held on substantive residual load lost power button
  • Holding F9 or F11 at startup does nothing.
  • Win7 32 disk turns but will not start.

  Which exhausts my troubleshooting led by Google, any ideas out there?

  Thank you

  Ken

  Try to get the hard drive to see if you can get into the BIOS with F10. If that gets you more far, he can point to hdd bad start to stop.

• HP elitebook 2540p - failed to get on the front office of the laptop freezes?

  
  I am trying to reset the Bios, HARD drive check, using the Windows startup options, but the laptop freezes as change personal settings. I spent C A D (just) before it slows down and then completely freezes. Clues please? OS is XP Pro.

  Hello

  Try to start the system in safe mode (press F8 at the HP logo and use the arrows to select Safe mode and enter)

  If you are able to start in their.

  Start - Run - type msconfig and enter.

  In the Startup tab, disable all programs and restart.

  

• EliteBook 8540w randomly freezes at startup

  Hello

  Since I activated the encryption of the hard drive in HP ProtectTools and invalidate it later, I experience random freezes at startup of Windows 7 Professional 64 bit. The gel has also occur when booting from the Windows 7 DVD and a reinstallation of the operating system Windows 7 also has not fixed the problem.

  Help, please.

  Thanks in advance,

  Donenzone

  You might want to try a complete reformat of the hard drive and reinstall W7.  Ugly process, but then you will have a better palce to start with future debugging if necessary. However, before you do a reformat, try the following two procedures.

  Try this procedure:

  Disconnect the PC and open it. Clean all the dust. Carefully, remove and replace all the cables towards the mother board one at a time. Do the same for memory DIMM and the video and the sound of cards if you have a. Plug your PC give a TI a go.

  Here is another list of things to try:

  1. Download cookienator (it's a gift) and clean the House.
  2. Open my computer and right mouse click the hard drive--> properties--> disk cleanup
  3. Start Internet Exployer--> tools--> Option Internet--> delete browsing history
  4. Open my computer and right mouse click on the hard drive-->-->--> Defrag tools properties now
  5. Open my computer and right mouse click the hard drive--> properties--> tools--> Check now
  6. Open the RUN and enter the following commands:

  cmd

  sfc / scannow---> it will check your critical system files and try to fix

  output

  7. open the window RUN and enter the following command: chkdsk

  8 restart and see how things are going.

• BSOD Atikmpag.sys Elitebook 8560w ati m5950

  Hi all

  I have problems with my Elitebook 8560w. I get the BSOD on startup all the time, when the login screen appears in windows 7. (atikmpag.sys)

  I have tried several things but I can't solve it, the laptop cannot start up if I use the standard vga driver.

  Things I've tried:

  Fresh install Windows 7 x 64, Windows 7 x 86, Windows XP x 64, Windows XP x 86

  Tried all versions of BIOS

  Tried all versions of drivers for video card, both HP and Ati with fres installs Windows.

  It's getting boring, please help me.

  Where can I get the latest version of the video Bios for my m5950? Who can solve my problem.

  Hello hlaca20. I understand that you have a problem with the blue screens that often occur during startup. Is this correct?

  You've tried quite a few steps to solve the problem. I think that the combination of the BIOS update, fresh install multiple operating systems and fresh drivers excluded the majority of software problems. Have you tried to test your equipment?

  If you have not deleted the partition of HP_Tools you can use the built-in tools that provides HP. You should test your memory and the hard disk to determine whether there are problems.

  This document describes how to run the hard drive test. Simply repeat the steps in selection of memory the second time to test the RAM.

  I'm waiting for your answer; have a great day!

• Qosmio G30 freezes at startup of Norton Internet Security 2008

  Norton Internet Security 2008 will freeze my computer because soon, it attempts to load and the only way to do is to restart the system by pressing the on/off key.

  My laptop is a Toshiba Qosmio G30-177 (model No. PQG32E-02G022GR) with Vista Ultimate and pre-installed NIS2007. I have no problem with this NIS2008 version on my other laptop (Qosmio F10 - PQF10E-02300JGR, WinXP MCE).
  NIS2007 works well on my G30 and I have no problems at all, but more recent versions of NIS seem to be in conflict with my system:

  1. I am able to install and run the new version, download all updates and adjusting the settings. Maybe, a couple days later my computer freezes after start in exactly when the NIS tray icon appears. For a few seconds there is simply no response of the system at all and the LED of my laptop show that any HD activity has ceased. After having been inactive during those seconds, the cooling fan will start to operate at maximum power, creating a huge noise that I never experienced before, not even while the CPU was operating at 100% for a while due to other programs. Force a reboot, that's all I can do.

  2. now, this time, I rebooted my laptop successfully even once (took a few attempts) and it all of a sudden not freeze. Then I disabled the firewall and auto-protect at all times, so there was no freezing at startup and I just had to enable both the firewall and auto-protect after start manually. In order to avoid the gel again after the reboot, I always disabled NIS before shutdown. For one or two days of workaround has been quite successful.

  3. all of a sudden, after one or two days, this work around will become useless, because the system begins to freeze again at the time of the icon is displayed. In this case, restart has no effect at all, and NIS will continue to freeze at startup. I also tried to prevent form from NIS to ccApp.exe run automatically at startup (administrative tools > system configuration > "Startup" tab). It's successful and my laptop is able to start normally, but if later I try to start NIS manually, it will freeze again.

  I had this problem since NIS2008 just came out, so I thought that at the same time an update Windows or Norton may have solved the problem, but this weekend I gave another NIS2008 trying without success. I'm pretty sure that the problem is not caused by other software than Windows or Norton, because I also tried to install NIS after a full system recovery, so I've only preinstalled NIS2007 and Vista on my laptop. I use Norton removal tool and follow the instructions to uninstall before attempting to install the new version of course.
  My last hope was that the version of NIS2009beta somehow would not freeze my system, but it does. It does not matter if I try to start 2008 or version 2009beta, the problem is exactly the same.

  What really motivates me almost crazy is the fact that NIS works perfectly for a while, then needs enough small workaround, and then after some time completely refuses to work. In these two days I do not change system settings, install or uninstall programs or doing whatever it is that I felt might conflict with NIS...
  So far, I have no idea of the solution and have again use NIS2007.

  Someone knows how to fix this?

  Hello

  To be honest I don t use the Norton internet security because it slows down the performance of the laptop and he needs too many resources.
  I used the NIS06 and after several months of use I removed it from my system for the reasons mentioned above.

  I put really know what might be a problem with your Norton Internet Security but I guess its associated software question maybe there are a few compatibility issues with vista and NIS08. Who knows...

  In my opinion, you should first check the Symantec Web site for more details.
  Maybe these questions are mentioned somewhere in the FAQ section and maybe some updates or patches are available.

  Good bye

• Where can I find a set of RAM for my Elitebook 8560w 2x16GB?

  The Elitebook 8560w is said to have 32 GB memory maximum capacity in two slots of RAM SO-DIMM 204 pins.  Unfortunately, I did not have chance to find a set of RAM 2x16GB with the correct specifications (1333 MHz or 1600 MHz). Can someone point me in the right direction?

  Hello
  I've yet to see a single 16GB sodimm module. The chipset can support 32 GB of RAM, but in case that the laptop has only 2 slots you are limited to 16 GB only. I've seen laptops with 4 memory locations, but they have been adapted...

• Problem updating Windows on Hp EliteBook 8560w - HP ProtectTools Security Manager 8.1

  When I ' try to update Windows 8 Preview of Windows 8.1 on a laptop HP EliteBook 8560w, I ' am getting this error message: "before upgrade you to Windows 8.1 Preview, uninstall these apps: HP ProtectTools Security manager, HP WebCam.

  Hp ProtectTools 8.0.2.1341 Security Manager is installed with the password manager and Credential Manager.

  Someone had this problem and fixed it yet?

  Thank ' s!

  Hello!
  Thanks for posting in the HP support forum!

  8.1 Microsoft Windows (although very good and big update ) is still in BETA (testing) phase and is not officially supported.

  Windows has features upgrade analysis and that it has detected that HP ProtectTools are not (yet) compatible with the new operating system (new update) - still in test.

  Note that this OS is still in beta and may contain bugs. In addition, he brings a few changes that any other 3rd party suppliers must take into account and it will take a while until the program is compatible.

  I recommend - if you want to test the new operating system, install fresh on another computer to test (processing Edition), not a production machine. Otherwise, for your laptops of business - use only the final versions of the software (such as Windows 7 SP1 or Windows 8).

  Let me know if I can help you further!

  IT_WinSec

  Please, take into consideration my location (Europe) and time zones. I'll try to give the answer as soon as possible.

• HP EliteBook 8560w Win8.1 does not fingerprint IE11

  CZE: Hi,

  Vlastnim for laptop HP EliteBook 8560w u Saada jsem provedl update na CZE Win 8.1 Pro x 64. Bohužel in. installation nastroje HP Password Manager 8.0.1.1328 a jeho současti v IE11 přihlašovani nefunguje mi. Přihlašeni počitače funguje v pořadku, ale v IE11 to sice objevi ikóna tohoto nastroje, ikóna problikne, že byl načten, ale do formulaře learn otisk is nic nevyplni.

  I chyba mě, nebo s neni IE11 kompatibilni nastroj u?

  ----------------------------------------------------------------

  Google translation to ENG: Hello,.
  I have a laptop computer Watt HP EliteBook 8560 with whom I made the update 8.1 for Win x 64 in English unfortunately, after installing the HP Password Manager 8.0.1.1328 and part of me does not connect in IE11. Connect you to the computer works fine, but in IE11, well as the icon flashes of this tool icon, fingerprint was loaded, but the form page does not do anything.
  It is a mistake for me or tool is not compatible with IE11?

  Ignore the box below this one. This site won't let me edit or input text from my smart phone without using the code box. I got my fingerprint reader to work in Windows 8.1 (both windows login and in an internet browser) using the blog that I mention in my post at this link: http://h30434.www3.hp.com/t5/Notebook-Operating-Systems-and-Software/HP-J070CA-Windows-8-1-Validity-Fingerprint-Reader/td-p/3025495/highlight/true/page/3 . It's, I believe, the sixth (6th) post by Melissa_01 (me) on the page in the link.
  

  Hey, I got it to work for me. Read what I posted in another thread (page 3) and see if it works for you too. http://h30434.www3.hp.com/t5/Notebook-Operating-Sy stems-and-Software/HP-J070CA-Windows-8-1-Validity-...
  

• 8570w HP EliteBook mobile workstation. Starting stalls.

  My company uses HP laptops, and that the warranty is up, we change our laptops. My last two phones were EliteBook mobile workstations. Both have the same problem. My current EliteBook is a 8570w. Two laptops at home and at work, the appropriate docking station dock. Here's the question. If I have a USB device, as a recorder Sony handheld, connected to any of the USB ports, the boot stops at the 'stage of HP logo' and will not proceed until I disconnect the USB device. After starting, I can reconnect the USB device. It's annoying to have cross the disconnection - connect the process, I decided to find the source of the problem and fix it. The problem is that neither I nor anyone else seems to have the answer, but probably the Hang Up is in the BIOS. Is there a a way to solve this problem by making a correction in the BIOS. It seems strange that the boot sequence can not handle a 'active USB device' temporarily ignoring it. Is there a solution to this problem?

  Hello again hot_joc,

  It is good to hear from you again!

  As my knowledge and resources are only oriented towards consumer product, I recommend you contact our technical support at the 1-800-474-6836. If you do not live in the United States / Canada region please click the link below to get help from your region number.

  http://www.HP.com/cgi-bin/hpsupport/index.pl

  I hope this helps!

  Concerning

• EliteBook 8560w: 8560w w / external projector does not not under Linux or Windows 8.1

  I recently bought an Elitebook 8560w opportunity and installed 8.1 for WIndows and Linux in a dual-boot configuration.  Using the laptop for weeks caused no problems at all.

  I used the display port on the screen on a TV 720 p to Samsung to mirror, so the kids can play games and it works perfectly, but when I try to connect to a home theater receiver as a passage to a projector 1080 p, the projected screen turn black for a few seconds, and then correctly show the desktop. This trend will continue indefinitely.

  I hooked it goes back to the 720 p TV and it works perfectly.  The problem exists in Linux and Windows.  I uninstalled the drivers and reinstalled a different version in each operating system.

  Ideas?

  The Elitebook works and no hardware or software problem.

  You may need to have an active DisplayPort to HDMI adapter since signal must pass the home theater receiver.

• My Toshiba laptop freezes!

  Whenever I connect and the office charge my laptop freezes and the only way it works is when I boot in safe mode! Can anyone help? I have a Toshiba Satellite L300-1BW on Windows Vista! Thaks in advance to anyone who can help!

  Hello

  You could try a more ancient date from the system restore - system restore can also be made with the Startup Repair tool
  If there is available Restore Points. Your Toshiba drives allow a startup repair. Just put in the DVD and
  then set the Boot Options on the DVD that you start or adjust the CMOS/BIOS to use the DVD as 1st boot device.
  (Usually F12 for device startup and F2 for the BIOS/CMOS settings options (for Toshiba).)

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  Try the above and if no help do the following:

  Try Startup Repair - you should have a Vista disc, otherwise you can try this mode safe mode if you can get there.

  This tells you how to access the System Recovery Options
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  Try runnng Chkdsk of Recovery Options
  (it of a more efficient way to manage to restart the computer and might work)

  -----------------------------------------------------------

  How to perform a repair for Vista Installation
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

  This tells you how to access the System Recovery Options
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  --------------------------------------------------------------------------

  If you are running follow these steps:

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log.  You can paste portions of error here, note that some Articles
  could repeat so only paste each only once in sections. A section is usually 10 lines or more.
  http://support.Microsoft.com/kb/928228
  Rob - bicycle - Mark Twain said it is good.