Elm 9.1 to 11.5 plm

Similar Questions

• Upgrade CUCM 9 to 10

  While I intend to improve CUCM from 9 to 10, understand that I need to generate the v9 ELM licence application and send to Cisco to generate the v10 license key.

  Would like to confirm the license generate demand can be performed on CUCM v9 ELM before moving on to v10 PLM.

  Your inputs are appreciated!

  Roy

  Hi Roy,

  It is not so with CUCM9.

  After u upgrade to CUCM 9, you must share the generated CUCM9 file so that you can obtain the permanent license file.

  You need to share the file LCU before migrating to CUCM9. This file contacted PUB CUCM 7/8 to get the number of users of BASIC/Essential/CUWL Std.

  regds,

  Aman

• Rehost licenses of ELM of connection of the unit to the server CUCM PLM

  Hi all

  I just finished a CUCM migration / MCS 8.0.3 upgrade to UCS 10.5.1 using PCD. I will now upgrade my 9.1.2 Server stand-alone connection of the unit to the 10.5.1 version tomorrow night. My question is about licensing. When I upgraded version 9.1.2 connection unit I decided to re co ELM since my CUCM cluster was still on version 8.0. Now that I have improved my CUCM cluster, I have two license servers - PLM for Call Manager and ELM for the connection of the unit. I was advised to move the licenses of connection of the unit to PLM, but I don't know how to do it. I have already contacted Cisco licenses and they tell me that everything is ready to go, but they have not told me HOW to do it (I know they are probably deluged with requests).

  Can someone point me to a link or describe briefly the process please?

  Thanks in advance!

  Lisa

  You probably didn't clearly explain what you wanted to do, he will be re - host licenses of a PLM to one another as before PLM with the MAC addresses of license.

• understand the ELM with the cluster of CUCM 10.5.2

  Hi all

  I have 2 Server CUCM (Published + subscribers) on different BE6K 2.  With each installed CUCM there is a (non-self) ELM.   ELM published CUCM server is active and I can load licenses and all is well.  For the ELM server with subscriber he declares to be in demo mode.

  I read somewhere that we can have only one ELM server per cluster.  Is this correct?  Is there a possibility of ELM cluster?

  What happern for licenses if the first server is done and ELM + CUCM PUB are down?

  I suppose any document/URL that explain all this.

  Thanks in advance.

  Hello

  With CUCM 10.5 ELM has actually changed PLM (first License Manager). PLM is unable to operate as a cluster. The info is attached below taken from the Guide of SRND Collab;

  Redundancy

  First LM is deployed as a non redundant application. In the case where the application of the first LM become unavailable (for example, if the first LM VM problems of operating system and it will not start), the customer has 60 days to restore the first LM application prior to the application of the licence. Applications run for a period of 60 days without communication with the first LM.

  For the restoration of demand for premium LM, another application installed first LM (such as an instance resident Co) can be created by add the product inventory to the new application of first LM. Since the MAC address of the virtual machine running the new PLM application would be different, the transfer of the registration of the license to this new first LM file would be necessary. Otherwise, first LM can be restored from a backup recovery system (DRS) disaster. In this case, configure the MAC address on the first LM new and original VMS, otherwise the recording of license should be transferred to the new virtual machine. If license additions or changes have been made since the backup of the DRS, a new license file must be requested. A resident first co LM backup can be restored only to a request first LM resident, and a standalone backup can be restored only on a standalone first LM.

  Of;

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/CUCM/srnd/collab10/collab10/callpros.html#pgfId-1347951

  See you soon!

  Rob

• Can not copy the content of my Cybershot C901 of SE to my new Elm SE

  I need help.

  I managed to download Media Go on my PC and did a synchronization of the content (especially for media files) to Media Go environment.

  I then cut. At the time wherever I am, my old phone records WILL disappear. And when I connect the USB to my new Elm, I can not of course copy the 'old' files above.

  Its not obvious (to me) what I'm doing wrong.

  Can someone please help? Its my wife's phone and I'm getting an attitude

  Thank you

  Yes try what I said above.

• Sony PC companion - Elm: no Outlook synchronization more?

  Hello!

  Since the last automatic update, Sony PC Companion do more synchronize with my outlook.

  I use an elm, my PC has Win7/32 and I get the error message is:

  

  (Translation: the application could not start.) Some components that are needed to start this application are missing. Try again later).

  I tried later and once again and once again after the start and after reinstalling and so on, without change.

  Can someone tell me what I need to do? I really need the sync.

  Many greetings!

  Volker

  Second attempt to get the image appears.

  Ah, I see. This is probably the reason then since PC Companion sometimes gets blocked by security programs.

  Try asking your TI if it is possible to add PCCompanion.exe to the 'green list', so it will not be blocked. Could help.

  Offline Installer is something of a transfer as a suggestion for the future value.

• Missing menus of ELM Web Interface

  I just installed my first try ELM (9.1.2.10000 - 28)

  I can access the application from the elm admin. But once logged in, I see no menus. I have the title bar, but nothing else.

  I tried this on the two Chrome & Firefox.

  Anyone seen this before?

  Thank you

  GTG

  Hey Ross,

  This could be the problem.

  ELM GUI displaying only not on 29 + Chrome and Firefox 25

  CSCul30396

  Description

  Symptom:
  ELM GUI does not appear correctly, only the page header is visible.
  Conditions:
  The user tries to access ELM using the latest version of Chrome or Firefox.
  Workaround solution:
  The ELM GUI displays correctly on Internet Explorer 9 and 10, as Safari (Mac and Windows).

• Change of address IP autonomous 9.1 ELM

  Hi all

  I have a client who is the movement of data centers, and they are required to change the IP address of the stand-alone Server 9.1 ELM.

  2 questions:

  (1) what is the procedure to change the IP address of a stand-alone server ELM 9.1?  The procedure of CUCM 9.1?  I can't find a specific ELM document/procedure.

  (2) the ELM server IP address change will require the re-hosting of licenses?

  Thank you all!

  Joe

  Hey Joe,

  I guess the procedure to change the IP address of the ELM would be identical to CUCM using the command

  set eth0 ip network

  http://www.Cisco.com/c/en/us/TD/docs/voice_ip_comm/CUCM/install/9_0_1/IP...

  the IP address change will not re-hosting licenses require.

  regds,

  Aman

• On 10.5 PLM after DRS licensing issues

  Shortly after upgrading to 10.5 CUCM, we made a DRS Recovery, after doing the recovery that no licenses work. I see the .bin file which shows yet all the licenses, but they don't show up as installed under license use.

  Tips or advice would be great, please note, we run a system offline.

  When you have restored, also rebuild the virtual machine ON THAT PLM is hosted? If so, was the old address MAC defined as static, as recommended, if yes, then make sure that the new virtual machine uses the same MAC, if not the old VM is removed and you can not see what MAC has been that you need Cisco rehost the license for you.

• 9.1 Produst ELM in

  I'm under stand-alone ELM server. The IP address if the CUCM has changed and now I get the Instance of product to the hostname/IP address is already configured on this Enterprise License Manager. When I try to add the new server.

  There is no evidence of emissions in case of product,

  Someone had this problem and a solution?

  It will run on a UCS 9.1

  Hello

  Please check the following post, it should respond to your request

  https://supportforums.Cisco.com/discussion/11716476/problem-create-new-i...

  HTH

  Manish

• problem to create a new ip and host name on ELM

  Hello.

  I am a model with CUCM, UNITY and IM/PRESENCE in V9 in my lab.

  By the link to ELM I download the txt file and generate a license demo on www.cisco.com/go/licence.

  I create an account with the ip address 10.101.1.10, hostname SV000150 and login password to synchronize the license. Everything was ok.

  I need to change the IP address of cucm but not the host name.

  I'm connect to ELM and I remove my account first CUCM but now I can not create a new account CUCM with ip adresss 10.11.0.1and the same host name.

  There is a message saying: this IP address /Hostname is already create!

  I have to insert genuine license in my CUCM and I don't know what I can do.

  Thanks for your reply.

  Excuse my English is not perfect, I'm french...

  If a restart of the node running ELM doesn't let you overcome this problem, it's time to call TAC that the record did not get erased from the database.

• ELM 9.1 and recording conflict 9.1 CUCM

  Hello

  Have a stand-alone ELM server and a bunch of 9.1.1a CUCM recording to him who works very well for a few months.

  A few days ago the CPU was pegging the server of the ELM (process hostagt) and I couldn't restart this process individually and I did a graceful reboot of the ELM (utils rebooting the system) server and she came back to the top and everything was fine.

  Now, a few days later, I get alert of CUCM that synchronization of the ELM has failed for the last seven days and 53 remaining days ago.

  On the server of the ELM, under product Instancxes the CUCM there is a recording conflict error and says it is run by another ELM server. There is only a single ELM server. The license page CUCM says that it is managed by the ELM server who complains.

  I have restarrted the ELM server without change, and I tried to restart the Client of the ELM on the CUCM server without change.

  I have to delete the instance of the ELM Server CUCM product and it add?

  Y at - it something hung up the CUCM server and I need to restart other services on this subject?  I don't see much in the logs on a server.

  ELM and are all two CUCM version 9.1.1a.

  Thank you

  Hello

  It might;

  Symptom: Instance of product registration fails with an error that the product instance is already managed by ELM.

  Resolution: Log in to the CLI of the product you want to add, and then run client license registration reset which will erase its previous register with ELM.

  Of;

  https://supportforums.Cisco.com/docs/doc-34910

  See you soon!

  Rob

  "Why don't the best things always go away."

  -The band

• How to disable the features of PLM 6.2 features

  Hello

  We use PLM 6.2 and you need to disable the function of the business segment.

  However, we have already added configuration code to "CustomerSettings" as follows,

  < FeatureConfig configChildKey = 'key' > < / FeatureConfig >

  < add key = "Common.Segment.Enabled" value ="false" / > ""

  < add key = "Common.SegmentSecurity.Enabled" value ="false" / > ""

  When configuration is successful, and then restart iis and agile service and run configurations rollup

  and value found on the configuration to always show the 'real' and still have also woking.

  

  Can someone please hint us to turn this feature off.

  Thank you

  Your format is not correct.

• Cannot download photo on specification via PLM 6.2

  Hello

  We use PLM 6.2 and found error appear on GSM module step upload picture scenarios.

  Can someone we refer please to upload photo to this function. Please screen error like below,

  

  

  Thank you

  Jaturawit U.

  Hi Jaturawit,

  Please make sure that remote access container is running. And SetupAssistant to check the DRL setting. WebServices.Login and running lights. WebServices.Password.

  In addition, in order to collect the error message from the client, you can press F12 in the browser to open the debugging tool. Try again your workflow to click again to see if the error message appears on the tab of the Console for debugging tool.

• How to validate duplicate values in application PLM GTIN

  I'm new to PLM application. Please let me know mentioned below these questions.

  1. I need to validate GTIN number dupilcate value of Oracle database.

  2. once save the GTIN number in the summary of trade specification.while insertion of the value tab, it must validate only single value if not display the error message.

  3. where do I need to write the code and the file that is to write the code? If there is no example

  Thank you

  Floquet

  Ron Awesom...

  Its working fine... Thanks much for your support very much and I'm new to this PLM Oracle agile. This is the first time enter and I learned a lot of things. Because of you...

  Thanks again for your support...