Encryption basis for Aironet 1100
Have an 1100 AP and use the GUI to configure.
I know I want to use mac authentication, but I also want to use some type of encryption. I've been playing with it for the last 3 days now and peut t can't find a solution as to what I can do.
Can someone please send a config that would give me a basic 128 encryption, which could be used by the majority of my clients? I d also like this config to require the use of it.
These instructions assume that you start from the default values.
STEP 1: select the required WEP encryption and set a key of 128 bits encryption key 1. Your customers will need match this information. They will need a 128-bit key in the same dwelling.
Security > Encryption Manager
-Section of Modes of encryption
-Choose "WEP encryption" and select "mandatory."
-Section of encryption keys
-Set transmit the key 1 encryption key
-Encryption 1:12345678901234567890123456 key
-Encryption Key 1 key size: 128-bit
-Click on apply
STEP 2: Configure an SSID.
Security > SSID Manager
-List SSID (delete the default SSID and create your own)
-SSID list:
-SSID: my ssid
-The authentication settings:
-Select «Open authentication»
-NOTE: you can come back later and activate the MAC authentication. Keep things simple the first time through and did not use MAC authentication.
-NOTE: all the other settings on this page should be to the factory default.
-Click on apply
The following is the equivalent CLI instructions:
==========
interface Dot11Radio0
key size 128 bit 12345678901234567890123456 1 transmit encryption keys
mandatory encryption wep mode
!
My SSID ssid
open authentication
!
==========
Here is the complete configuration of my interface Dot11Radio0 from my living room to run:
==========
!
interface Dot11Radio0
no ip address
no ip route cache
!
encryption key 1 size 7 1823F25A0AB8494E9154647CF72C transmit key of 128 bits
mandatory encryption wep mode
!
My SSID ssid
open authentication
!
short-time slot
base speed - 1.0 2.0 basic basic-5, 5 6.0 9.0 basic-11, 0 12.0 18.0 24.0 36.0 48.0 54.0
root of station-role
No cdp enable
Bridge-Group 1
Bridge-group subscriber-loop-control 1
Bridge-Group 1 block-unknown-source
No source of bridge-Group 1-learning
unicast bridge-Group 1-floods
Bridge-Group 1 covering-disabled people
!
==========
I hope this helps.
Kent.
Tags: Cisco Wireless
Similar Questions
-
Aironet 1100/1200 series and Windows
Is it possible to use the Windows IAS Radius with Aironet 1100/1200 Series light? If yes are there problems you may need to pay attention to?
Respectfully
You can use the server Radius IAS for LWAPP. I'm not aware of any questions.
Someone else can add to this.
-> Sushil
-
Hello
I have a cisco aironet 1100 Series wireless access point.
by mistake I delete the IOS of the router and now I need to copy the IOS image again on it.
I need your help please.
For now, he has the Ethernet led RED, Green State, Rdio RED. T no Cisco IOS image file the spirits).
I downloaded the file c100-k9w7 - mx.123 - 8.jed
and I download the tftp (tftpd32) servers
I have the router connected directly to a pc with the static ip address of 10.0.0.2
but the problem is actually that I don't need the 1100 router ip address right now, I can't access it through a web browser.
and by a tftpd32 I try but no function.
I don't know what I'm doing wrong.
other things, it's that I did not find a clear manual on how to use a tftpd32 to transfer the file to the cisco router 1100 series.
Thank you.
I'll wait your hepls.
Convert a standalone Lightweight Access Point
http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html#wp161272 -
Where can I find the download of the base for a HP Deskjet D4260 printer driver?
Where can I find the download of the base for a HP deskjet D4260 printer driver? I have a new Windows 8 tablet running, and the only thing I can find is downloadable for the complete software suite. References from the HP website they have a base driver download but you don't tell where. Search all of lead them to the download of the complete suite.
Hello eworth3,
I followed on the specific page for this driver and found the same thing - my apologies that there is not a link on this page for basic training. I did a search on the site hp.com for this text and it took me to a page that has the base driver... I have included the link below. This is the basic feature software solution and is a driver software intended only to users who want a basic print and driver scanning for use with their device from HP all-in-one.
Thank you for that bring to our attention: I would ask to add the link to the specific page.
-
Base for OfficeJet 6830 and 6700 driver
I have a new printer Officejet 6830 I need diver Win7 database for.
I don't want the driver for 42 Mo 'basic' which is available on the Web site. I would just like to add a local printer... Standard IP port... have disk... and be able to use the driver file. I don't want to run the exe from the Web site that installs much more. It comes to load locally on a workstation T610
I also need the base for the 6700 drriver too
Your printer models are compatible with HPs universal printer drivers? If so a UPD is a quick and easy solution to your problem.
If what you see on the site of HP, it's what you get.
You can always try to recover the print of a model similar to printer driver if you manage to find one that is supported on your operating system. Printer drivers are generally flexible enough, unless they are specially designed for this model, like many old printers were. Browse the list of print drivers pre-installed in your OS to see if one is compatible with or not. You won't have access to all the features, but the basic printing features should work. Mix and match until you find one that works.
-
I am trying to download IE High Encryption Pack for a Web site.
original title: 128-bitIAM trying to Download THE High Encryption Pack for a web site that requires a 128-bit security. I am running ie8.
IAM trying to Download THE High Encryption Pack for a web site that requires a 128-bit security. I am running ie8.
In IE 8, click Help > a way Internet Explorer. It should say "strength of encryption: 128-bit." In other words, you already have 128-bit security. These high encryption Packs were for older versions of IE.
Windows XP does not include the necessary cryptographic providers for the 256-bit encryption level. Windows Vista and Windows 7 are supported 256-bit encryption level.
-
I have problems connecting an Aironet 1100. I was able to connect to the Web to do a software update on it. Now, I am unable to connect to access now. I have flashing LED AIRONET 1100. The lights flash in GREEN ORANGE RED.
Hello
Check the following link and based on the indicator signals you can understand what the problem is.
-> Sushil
-
Question about encryption keys for TP server 8710
I'm discovering the activation process of encryption keys for my telepresence server clusters.
I know that we need this encryption key (L-AESCDN7-K9). We need one per frame, or one per blade?
The encryption key is installed directly on each Blade Server, as you would apply the key to each of them. Each server blade has its own twist.
-
How to upgrade IOS for Aironet 1252 G
I'm trying to update the IOS for Aironet 1252 G wirless access point, I look at all the instruction and they do not make sense! And there is just no instuctions on how to upgrade the IOS in the WEB BROWSER interface. I just did an install of Windows Server 2008R2 and real simple compared to only raise AP and running, but there still Microsoft and their staff try to keep things simple for people where CISCO makes more complex theings.
Hello
If you try to update the IOS on a Cisco AP upgrade recomeneded uses the cli via a telnet session or console.
**************************************************************************** RECOMMENDED UPGRADE TROUGH CLI: The following are the proper steps to do an IOS upgrade in a CLI/Telnet session (This is the recommended upgrade): 1st: Use a TFTP server in the computer that you are going to use for the upgrades. If you don't have one, get the free TFTP server in the following link: http://tftpd32.jounin.net Note: Make sure that the computer and the APs are in the same subnet. For example and AP in default settings will have IP: 10.0.0.1, so you need to have the computer as IP 10.0.0.2, subnet mask: 255.255.255.0. 2nd: Download the IOS image from the Cisco.com Web site. Note: Do not "unzip" the image. 3rd: Open the TFTP server (make sure that the TAR file's name of the IOS image is shown as in the web site, because sometimes it gets renamed to "Download .tar" and if that happens you need to rename it). Browse the TAR file and select it, then click ok. 4th: Telnet the unit, go to enable mode and enter the following command: ap#archive download-sw /overwrite /force-reload tftp://IPAddress of_the_tftp_server/name_of_the_IOS_image_you_downloaded In this link, you must specify the extension, as an example: ap#archive download-sw /overwrite /force-reload tftp://10.0.0.2/c1200-k9w7-tar.122-13.JA.tar Note: The IOS image name is case sensitive, and it should be complete.
******************************************************************************This is the same procedure for any AP in IOS mode, the difference would be the image used for each specifc model.
-
I paid Adobe on a monthly basis for the SERVICE to be able to COMBINE (pdf) files into a SINGLE (!). HOW DO TO THIS PAGE TO DO!
Hi Richa,
Could you please send me the adobe on a personal message identification code so that I can see the exact subscription that you have purchased.
You can check the link below for instructions.
Document help Cloud | With the help of Adobe PDF Pack
Hope this will help you.
Kind regards
Hervé Khare
-
Good basis for Xeon L5430 VCA?
We have three host with this processor reported by vCenter servers: Intel Xeon L5430 @ 2 .66GHz.
We will soon present a new host with a processor Intel Xeon E5630 2.53 GHz server because it has hyperthreading, the L5430 has no hyperthreading.
Is 45nm Core 2 "Penryn" Xeon line of VCA correct basis for the L5430?
I looked at him and I see 45 nm' on the site of Intel and elsewhere... I've also seen "Harpertown" in product descriptions, which confuses me, because "Harpertown" isn't "Penryn".
Thank you, Tom
Visit this link:
You will get your answer.
-
Cannot use the CRS as a basis for a new implementation of trade
Hello, I want to use a CRS as a basis for a new implementation of trade.
In training, he works with the MyStore.Custom module.
My environment is ATG10.0.3 and I m using oralce 11 g express xe.
When I extend the userProfile in MyStore.Custom config/atg/userProfile.xml with
two properties (points and mystore) it takes no effect. I look in the ACC for the new properties,
but they aren't there.
If I put the code in config.jar/atg/userProfiling in the folder < ATG10 > CommerceReferenceStore/store/EStore, it works.
Is there someone who can help me, because I want to use MyStore.Custom.If it is confirmed now that your "MyStore.Custom" module is not being chosen. How do you start your server? You include 'MyStore.Custom' in the module names after "m" switch during the construction of your EAR by using runAssembler or if the starting on JBoss using startDynamoOnJBoss?
-
GANYMEDE conf for interface web aironet 1100
Hello
I have configured our access point for Ganymede and his works fine, but I still want one thing, web user interface & pass must use Ganymede.
How can I do this?
Thank you
Hello
I use a 1200, but maybe it helps.
Via the Web Interface, I can navigate to SECURITY > Access Admin and turn on an option called "authentication server if not found in local list". After having turned it on, I can use my username and password for the Web Interface and in the Telnet program.
-
Need BIOS for Satellite 1100-z17 file
Can you help me with a bios for toshiba satellite 1100-z17 file because I tried to update the bios with satellite 1100-z1 and my phone is dead!
Please help me!
Kind regards
getPost edited by: get
Hello get them
Sorry for this, but you must be kidding!
You know you need to use the good BIOS and the proper procedure upgrade of BIOS, don t you?
Incorrect BIOS may damage the motherboard and I'm afraid of what happened on your computer laptop m. ;(
Maybe you are a lucky man and the BISO right will bring the motherboard to life, but it is very questionable.
I think that in this case only, a technician can help you. Try to contact the ASP in your country.
-
Need to cover base for Satellite A210-12U
I need to have a Toshiba Satellite A210-12U fixed base cover.
Does toshiba sell Basic for this laptop?> Does toshiba sell base covers for this laptop?
You can order each compatible part of your local Toshiba authorized service provider.
Guys are able to order parts directly from Toshiba.Take a look on this page where you can find all available worldwide FSA:
http://www.Toshiba.EU/innovation/generic/ASP_SUPPORT/
Maybe you are looking for
-
I can't see my emails on a PC, in Thunderbird
My problem is that I see only my old Yahoo from my laptop, Thunderbird mails. If I try to view them using webemail on the same computer, the Inbox is empty.If I try to view them using webmail or Thunderbird from another PC, laptop, my Inbox is empty.
-
LaserJet 4 driver for Windows 7
My LaserJet 4 works fine - just as HP promised when I bought it. Now, customer support HP told me that HP has made the choice NOT to write a driver for it to work with Windows 7. How can I use my LaserJet 4 - ideas? I hate to drop it into my local
-
Updated portable Satellite P30-144 with bluetooth
I know it's a stupid question, but what impact installing the bluetooth on my laptop battery has the current wireless configuration. I'm already upset that I can't use my old Canon BJC-50 with the laptop because it didn't not a parallel port has no i
-
HTML, unable to change fonts in the list
Madam/Sir, After trying several things I could not even understand how to solve this problem. I'm doing the text before a list Append "BOLD", but the text in the list do not. As shown in the code (which is in the attachments) I said different fonts t
-
I don't think I should buy another copy of PhotoDelux, so, how do I reinstall on my new PC?