Endpoint Cisco PIX 506
The 6.3 (3) Cisco PIX 506 will work as an endpoint? How to configure it?
Do you mean IPSEC endpoint. If so, Yes... You can configure the following:
No nat:
NAT (inside) - 0 100 access list
access-list 100 permit ip 192.168.180.1 host 10.1.1.0 255.255.255.0
IP local pool vpnpool 10.1.1.1 - 10.1.1.254
Crypto map configuration:
Permitted connection ipsec sysopt
Crypto ipsec transform-set esp-3des esp-md5-hmac RIGHT
Crypto-map dynamic dynmap 10 transform-set RIGHT
map mymap 10-isakmp ipsec crypto dynamic dynmap
client configuration address map mymap crypto initiate
client configuration address map mymap crypto answer
client authentication card crypto LOCAL mymap
mymap outside crypto map interface
ISAKMP allows outside
ISAKMP identity address
The policy configuration:
part of pre authentication ISAKMP policy 10
ISAKMP policy 10 3des encryption
ISAKMP policy 10 md5 hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
VPN group configuration:
vpngroup address vpnpool pool abcvpn
vpngroup split tunnel 100 abcvpn
vpngroup idle 1800 abcvpn-time
vpngroup password abcvpn *.
username cisco password cisco
Tags: Cisco Security
Similar Questions
-
Problem recording with Pix 506
Hello
I have an old pix 506, it has been disconnected for a while and now I feel I want to use. But I forgot the password, I can ping from the port to my pc but I can't ping from pc-to the pix.
No idea how to reset the password or delete it there or return to the default factory setting.
Thank you
See this document:
Password Recovery and AAA Configuration procedure of recovery for the PIX
Factory reset after the recovery of password:
write erase
reload
sincerely
Patrick
-
Hello
I meet a few small problems with a v6.3 (4) pix 506 and 2924c-xl switch.
On the switch for the pix port, many input errors and Runts appear.
On the pix, there is a VLAN configured and the trunk port is configured as
mentioned in the Release Notes for Pix.
I could not find a bad configuration here, but maybe someone has an idea how to
solve this problem.
Thank you
just a few lines:
[pix]
Auto interface ethernet1
physical interface ethernet1 vlan2
logical interface ethernet1 vlan999
[go]
interface FastEthernet0/1
PIX506 description
switchport trunk encapsulation dot1q
switchport mode trunk
spanning tree portfast
No cdp enable
interface VLAN2
IP x.x.x.x 255.255.255.0
no ip directed broadcast to the
no ip route cache
Hello
Do you find some useful info on the Runts on 802. 1 q port.
Runts on an 802. 1 q trunk port.
A catalyst 2900XL or 3500XL that receives a frame of 802 bytes. 1 q encapsulated 64 or 66 on a port trunk counts as a runt. However, it continues to transfer the weft.
This issue occurs when you connect to the Cisco 7960 IP phones switch when using a VLAN auxiliary (voice).
This issue is cosmetic and because of an ASIC limitation.
It should not cause any degradation in the performance of the switch.
For more information, see Cisco ID CSCds32999 bug (only for registered customers).
Cisco IOS Software version 12.0 (5.4) WC1 or later
On the errors of entry...
Entry errors
Entry mistakes provide a count of errors that occurred when trying to get packages from this port. The meter includes errors CRC and the framework. However, it does not include ignored packets. It is a list of entry errors:
CRC errors: Occur when the packets received fail the CRC check.
Frame errors: occur when the receiver frame is not complete.
Ignored Counter: Account number of frames dropped on entry due to depletion of resources in the switch fabric.
Meter overruns: occurs when interframe gap (IFG) are too short. In this case, a new Ethernet frame arrives before the previous one is completely stored in the shared memory.
http://www.Cisco.com/en/us/products/hw/switches/ps607/products_tech_note09186a0080125913.shtml
regds
-
Erase the old Cisco PIX beyond recovery
I have an old Cisco PIX that has been configured with the VPN site - to many who have been migrated to a new ASA last year. The same IP addresses, PSK, etc are still active on the SAA new config info stored in the PIX is still valid. I want to erase the memory on the PIX beyond all recovery-ability, to the same specifications of DoD to erase hard drives. I don't like leaving the ASA in a usable state after - it goes to the recycling center. I'd like to open the case to remove internal parts.
I am aware of the process to restore the default settings, but this process is secure? If a hacker were to get the PIX may recover data deleted from memory? Cisco certifies all process of erasing/destroying data securely?
Thank you in advance.
Cisco had a download that would actually crush flash with zeros that you could use. It is no longer available because this product is long after the end of life. Even if you had a copy, it is not spec compliant DoD for sanitation.
Unfortunately, your option at this stage would be to open the casing and physically destroy the internal memory card.
-
Connectivity random Cisco Pix 501
Hello. I'm having some trouble with my CISCO PIX 501 Setup.
A few months I started having random disconnects on my network (from inside to outside). The machines can ping the DC or the Pix, but impossible to surf the internet. The only way to make them go outside is a reboot of Pix.
My configuration is:
-----------
See the ACE - pix config (config) #.
: Saved
: Written by enable_15 at 09:23:07.033 UTC Tuesday, June 3, 2014
6.3 (3) version PIX
interface ethernet0 car
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate 8Ry34retyt7RR564 encrypted password
2fvbbfgdI.2KUOU encrypted passwd
hostname as pix
domain as.local
fixup protocol dns-length maximum 512
fixup protocol esp-ike
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
access-list acl_out permit icmp any one
ip access list acl_out permit a whole
access-list acl_out permit tcp any one
Allow Access-list outside_access_in esp a whole
outside_access_in list access permit udp any eq isakmp everything
outside_access_in list of access permit udp any eq 1701 all
outside_access_in list of access permit udp any eq 4500 all
outside_access_in ip access list allow a whole
pager lines 24
Outside 1500 MTU
Within 1500 MTU
outside 10.10.10.2 IP address 255.255.255.0
IP address inside 192.168.100.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
history of PDM activate
ARP timeout 14400
Global 1 10.10.10.8 - 10.10.10.254 (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Access-group outside_access_in in interface outside
access to the interface inside group acl_out
Route outside 0.0.0.0 0.0.0.0 10.10.10.1 0
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
Enable http server
http 192.168.10.2 255.255.255.255 inside
http 192.168.10.101 255.255.255.255 inside
http 192.168.100.2 255.255.255.255 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
ISAKMP nat-traversal 20
Telnet timeout 5
SSH 192.168.10.101 255.255.255.255 inside
SSH timeout 60
Console timeout 0
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd outside auto_config
Terminal width 80
Cryptochecksum:7f9bda5e534eaeb1328ab08a3c4d28a
------------Do you have any advice? I don't get what's wrong with my setup.
My DC is 192.168.100.2 and the network mask is 255.255.255.0
The network configuration is configured to set the IP of the gateway to 192.168.100.1 (i.e. the PIX 501).
I have about 50 + peers on the internal network.
Any help is apprecciate.
Hello
You have a license for 50 users +?
After the release of - Show version
RES
Paul
-
Active FTP problem between Checkpoint and Cisco PIX
Hello
I am facing a strange problem.
Many of our customers have achieved a Checkpoint FW-1/VPN-1 4.1 SP6 (the last before NG). When they try to connect to an FTP server that is located behind a Cisco PIX firewall, they are not able to transfer data: the connection is established, the authentication to follow, but at the stage of the 'LIST' the connection 'freeze' and the user must close the FTP client.
Users are facing this problem ONLY in Active mode: passive mode works very well. Turn passive mode FTP client isn't acceptable workaround for most of my clients.
The problem seems to be related only to the firewall Cisco PIX and active FTP.
Please, what is someone encountered the same problem?
Could someone give me any help?
Thank you in advance.
Paolo
Yes it is a (global) problem, even with the last checkpoint firewalls. What happens with Active FTP, it's that each command (get, list, etc.) causes another log on the client (source port) to the server on port 21. If you run netstat from the customer you can check this for yourself.
What normally happens, with HTTP, FTP, telnet, which have are, it's that the client makes a connection to port 21, 23 etc then returns with a port source such as 1936, 1980, 3000, etc..
Connect problem with statefull firewall is they do not allow multiple sessions control port number on a destination, as well as a source port can be bound to a destination port, in this case, 21 for FTP. I Don t see it changed, an extreme security risk any time soon, since it s, someone else might be hopping session and block this type of traffic, it's what the stateful firewall are all about and FTP servers are problably the machines more pirated on the planet.
You´ve mentioned the workaround solution, unfortunately that s the only way, change your passive customers, I think that Unix/Linux customers have a problem with this, change your FTP server can also help, there are multiple servers that can be configured to disable Active FTP, I wouldn know exactly, I only network & firewall... maybe someone else can move on this...
-
I need help setting up a Cisco PIX 506th Version 6.3 (5)
I use the PDM to configure the device, because I don't know enough of CLI. I want to just the simplest of configurations.
Here is what is happening, I set up then I hang the Interface 1 to my laptop and use DHCP to get an ip address, but I can't get out to the internet like that. Thanks PDM tools, I can ping outside the IPS very well.
6.3 (5) PIX version
interface ethernet0 car
Auto interface ethernet1
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate the encrypted password of DkreNA9TaOYv27T8
c4EBnG8v5uKhu.PA encrypted passwd
hostname EWMS-PIX-630
domain ciscopix.com
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
object-group service udp test
port-object eq isakmp
inside_access_in ip access list allow a whole
access-list inside_access_in allow a tcp
access-list inside_access_in allow icmp a whole
Allow Access-list inside_access_in esp a whole
inside_access_in tcp allowed access list all eq www everything
inside_outbound_nat0_acl list of permitted access interface ip inside 10.10.10.96 255.255.255.240
inside_outbound_nat0_acl ip access list allow any 10.10.10.192 255.255.255.224
pager lines 24
timestamp of the record
recording of debug trap
host of logging inside the 10.10.10.13
Outside 1500 MTU
Within 1500 MTU
IP outdoor 75.146.94.109 255.255.255.248
IP address inside 10.10.10.250 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
location of PDM 10.10.10.1 255.255.255.255 inside
location of PDM 10.10.10.13 255.255.255.255 inside
location of PDM 10.10.10.253 255.255.255.255 inside
location of PDM 75.146.94.105 255.255.255.255 inside
location of PDM 75.146.94.106 255.255.255.255 inside
location of PDM 10.10.10.96 255.255.255.240 outside
location of PDM 10.10.10.192 255.255.255.224 outside
PDM logging 100 information
history of PDM activate
ARP timeout 14400
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 0 0.0.0.0 0.0.0.0 0 0
inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 75.146.94.110 1
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-RADIUS (inside) host 10.10.10.1 server timeout 10
AAA-server local LOCAL Protocol
Enable http server
http 10.10.10.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
ISAKMP allows outside
ISAKMP peer ip 206.196.18.227 No.-xauth No.-config-mode
ISAKMP nat-traversal 20
ISAKMP policy 20 authentication rsa - sig
encryption of ISAKMP policy 20
ISAKMP policy 20 md5 hash
20 1 ISAKMP policy group
ISAKMP duration strategy of life 20 86400
part of pre authentication ISAKMP policy 40
encryption of ISAKMP policy 40
ISAKMP policy 40 md5 hash
40 2 ISAKMP policy group
ISAKMP duration strategy of life 40 86400
ISAKMP policy 60 authentication rsa - sig
encryption of ISAKMP policy 60
ISAKMP policy 60 md5 hash
60 2 ISAKMP policy group
ISAKMP strategy life 60 86400
Telnet 10.10.10.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd address 10.10.10.2 - 10.10.10.5 inside
dhcpd dns 68.87.72.130
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd allow inside
btork encrypted Ww3clvi.ynWeGweE privilege 15 password username
vpnclient Server 10.10.10.1
vpnclient-mode client mode
vpnclient GroupA vpngroup password *.
vpnclient username btork password *.
Terminal width 80
Cryptochecksum:5ef06e69c17b6128e1778e988d1b9f5d
: end
[OK]any HEP would be appreciated.
Brian
Brian
NAT is your problem, IE.
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 0 0.0.0.0 0.0.0.0 0 0presumanly first NAT is fot your good VPN that acl looks a little funny, what exactly are you doing with that?
The second NAT is the real problem but for outgoing internet access - the NAT statement, you said not NAT one of your addresses 10.10.10.x which is a problem as 10.x.x.x address is not routable on the Internet.
You must change this setting IE. -
(1) remove the second NAT statement IE. "no nat (inside) 0 0.0.0.0 0.0.0.0.
(2) add a new statement of NAT - ' nat (inside) 1 0.0.0.0 0.0.0.0.
(3) add a corresponding statement global - global (outside) 1 interface.
This will be PAT all your 10.10.10.x to external IP addresses.
Apologies, but these are some CLI commands that I don't use PDM.
Jon
-
Remote Desktop from Win7 not passing is not by the cisco pix firewall, but xp can.
our company lan remote office work like this:
Win7 for win7 ok
Win7 for xp ok
XP and win7 ok
XP to xp ok
Which leads me to believe that all the parameters and features of firewall and rdp pc work fine.
our remote users connect via the cisco through our cisco pix vpn client business and Remote Desktop works like this:
inside lan xp ouside xp OK
inside lan xp ouside win7 OK
Here's the problem:
inside to outside win7 win7 ==> does NOT connect to (rdp that is)
inside win7 for xp outdoor ==> does NOT connect to (rdp that is)
External clients CAN of course accept rdp because it works when initiated by the xp machine.
ONLY win7 machines cannot use rdp through the cisco firewall
Yes, the dns resolves properly throughout.
Yes, remote desktop IS active (Yes, some may ask me that...)
Ping is not allowed through the firewall, so it makes no difference.
the result is the same whether the win7 firewall is on or off.
all the necessary pc firewall settings are good, as demonstrated in the first part.
Why can you connect the NO Win7? but the XP machines?
Any help is appreciated, thanks.
I think that there are some weird setting in Win7 that didn't exist in winxp.
Hello
The question is more suited in the TechNet forums. So I would say you mention the link and send the request in this forum for better support.
http://social.technet.Microsoft.com/forums/en-us/category/w7itpro
For any information related to Windows, feel free to get back to us. We will be happy to help you.
-
Cisco PIX VPN pass through (sorry, tricky!)
Hello
I'm having some problems with allowing IPSEC through a Cisco PIX 501. The configuration is the following:
Host (mail Client) (192.168.1.111)
|
PIX (NAT)
|
INTERNET
|
(Checkpoint) VPN server
The problem is, the PIX guard dropping my outgoing isakmp packets on its * internal * inetrface!
710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp
710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp
710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp
710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp
710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp
710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp
Does anyone know why it does this? Anyting to my in-house (security level 100) should go directly to my giving and external interface on the net. For some reason, is to treat the isakmp packets differently...
I have included my config as an attachment, can we see what I missed or have any ideas why it loses the isakmp packets?
Thanks for any help.
Nick Chettle
Check users. C and edit it with your favorite editor. Check if you have a private or public IP address!
I tried to find in the really safe base article I've seen a couple of months ago but I can't find any more.
https://SecureKnowledge.checkpoint.com/SK/public/intro.jsp
See also this FAQ:
http://www.phoneboy.com/bin/view.pl/FAQs/SecureClientFAQs
See CheckPoint VPN-1 Guide that is on the installation CD or go to the web site of checkpoints, BUT you need a valid account Center user to read and download the documentation. Start looking at page 119 and 211.
As usual, nothing is free at the checkpoint.
http://www.checkpoint.com/support/technical/documents/docs_r55.html
sincerely
Patrick
-
PIX 506 - cannot connect to PDM more
We have a PIX 506 in a test environment that has been configured in the past using Netscape. Now when we try to connect via https, Netscape says "unable to connect to the server (TCP error: i/o error). The PIX is version 6.1 (1) and PDM is 1.0 (2). I can connect via telnet and change the configuration, but I was not able to get the connection Internet work anymore.
I captured the connection with ethereal and I see 3 packets, the connection, then the client sends a SSLv2 Client Hello, then the PIX closes the connection. When I dump the telnet configuration, I get:
Enable http server
ClientName http 255.255.255.255 inside
where clientname is defined above in the name and the entries of "place of pdm.
The PDM installation guide has a troubleshooting section, and it says to make sure the clock is set to UTC. "show clock" indicates the time and date, but no area is listed.
You have changed the IP address on the PIX interface at some point? If so, try to regenerate public/private key pairs. Fox
> ca related rsa
> key gen rsa 512 AC
> ca save all
or you can just run the command 'setup' from config mode and it'll do all that for you. Then try to reconnect.
-
Cisco PIX 501 to Cisco 3005 concentrator via remote access
Hello people,
I need your help.
We got a Cisco PIX 501 in one place and this pix is configured for pppoe connection. The pix connects to internet via the pppoe client. an official ip address ping works well.
So what I want to do is to establish a tunnel von between this pix and a cisco 3005 concentrator.
But I failed to establish it.
Here are the pix config. the acl? s are only for the test and will be replaced if it works.
6.3 (4) version PIX
interface ethernet0 10baset
interface ethernet1 100full
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
activate the password xxx
passwd xxx
hostname PIX - to THE
domain araukraine.ua
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
outside ip access list allow a whole
inside_access_in ip access list allow a whole
pager lines 24
opening of session
Monitor logging warnings
logging warnings put in buffered memory
MTU outside 1456
MTU inside 1456
IP address outside pppoe setroute
IP address inside 192.168.x.x 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
PDM location 192.168.x.x 255.255.255.224 inside
forest warnings of PDM 500
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
outside access-group in external interface
inside_access_in access to the interface inside group
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server local LOCAL Protocol
the ssh LOCAL console AAA authentication
Enable http server
255.255.x.x 192.168.x.x http inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
255.255.x.x telnet inside 192.168.x.x
Telnet timeout 5
SSH 194.39.97.0 255.255.255.0 outside
SSH timeout 5
management-access inside
Console timeout 0
VPDN group pppoe_group request dialout pppoe
VPDN group pppoe_group localname [email protected] / * /
VPDN group ppp authentication pap pppoe_group
VPDN username [email protected] / * / password *.
encrypted privilege 15
vpnclient Server 212.xx.xx.xx
vpnclient mode network-extension-mode
vpntest vpngroup vpnclient password *.
vpnclient username pixtest password *.
Terminal width 80
the hub, I created a user pixtest, a group vpntest and I? ve created the rules of the network for example to what server, users behind the pix will be able to access.
And that? s all.
I couldn't send you exit pix or hub because I don't have an error or a message that the tunnel will be established.
What can be wrong?
Thanks for the replies
This configuration example shows how to create an IPsec tunnel to a computer that is running the Client VPN Cisco's (4.x and later versions) to a Cisco VPN concentrator 3000 to allow the user to safely access the network inside the VPN concentrator.
-
IKE Dead Peer Detection between Cisco ASA and Cisco PIX
I have a network environment in Star with about 30 offices of satellite remote using VPN Site to Site connectivity. The majority of remote satellite offices have the features of Cisco PIX 501 running PIX Version 6.3. The hub office runs a version 8.2 (1) Cisco ASA.
I configured Dead Peer Detection on the Cisco ASA device at the office hub with the default settings of the following-
Confidence interval - 10 seconds
Retry interval - 2 seconds
I think I'm right assuming that raises are limited to 3 before the tunnel is completely demolished. Basically, the problem that I am facing is with several remote satellite offices. What seems to be the case, the tunnel between the remote offices and the hub is demolished (probably because of the length of IKE, always 86400 seconds) and the tunnel then fails to renegotiate unless traffic is physically forced from the hub office. The tunnel NOT to renegotiate after satellite office, ONLY the end of the hub; so that means sending traffic to the satellite when the VPN tunnel is out of service, not to renegotiate the tunnel. The Hub office is a colo and therefore traffic rarely comes to that end, the tunnel remains so down until manual intervention occurs and the ICMP traffic is forced into the tunnel.
Should the KeepAlive and retry interval settings corresponds to both ends, for example if the two devices be configured for DPD?
What are the potential pitfalls to the extension of the life of IKE, and this will help or even hinder the problem?
Thank you in advance for helping out with this.
Hi Nicolas,.
I think that the two DPD settings must match on both ends, if these do not match then problems like yours might arise which seems to happen here, is that one end shows a tunnel down, but the other end may not detect it down, we could have to watch debugs, or record two ends to see if this is the case , setting in the meantime ike DPD for same timers could hetlp on.
In regard to the increase in the life expectancy of IKE, well you just need to be aware that this could allow keys to be discovered since these are not renegotiated unless the tunnel is down on the level of IKE. Other than that I don't see why this would affect you.
-
PIX 506 Web, Mail Config w/one IP
Hello, I am trying to configure my Pix 506 to allow outgoing traffic all and before 25,80 port traffic, 8080 and 7777 entrants to an internal web server (192.168.1.3,4) and mail server (192.168.1.2)
I have an external IP x.x.x.12
What Miss me...
Thank you. -rob
Here is my config:
interface ethernet0 car
Auto interface ethernet1
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
names of
name 192.168.1.4 NVDEV02
name 192.168.1.3 NVAPP01
NVEGVPN_splitTunnelAcl ip access list allow a whole
inside_outbound_nat0_acl ip access list allow any 192.168.1.0 255.255.255.192
inside_outbound_nat0_acl ip access list allow any external interface
outside_cryptomap_dyn_20 ip access list allow any 192.168.1.0 255.255.255.192
outside_cryptomap_dyn_20 ip access list allow any external interface
outside_access_in list access permit tcp any host x.x.x.12 eq 8080
outside_access_in list access permit tcp any host x.x.x.12 eq www
outside_access_in list access permit tcp any host x.x.x.12 eq 7777
outside_access_in list access permit tcp any host x.x.x.12 eq smtp
pager lines 24
opening of session
information recording console
logging trap information
Outside 1500 MTU
Within 1500 MTU
IP address outside x.x.x.12 255.255.255.0
IP address inside 192.168.1.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
local IP NVEGPOOL 192.168.1.30 pool - 192.168.1.49
location of PDM 192.168.1.2 255.255.255.255 inside
location of PDM NVAPP01 255.255.255.255 inside
location of PDM NVDEV02 255.255.255.255 inside
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_outbound_nat0_acl
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside, outside) x.x.x.12 www NVAPP01 www netmask 255.255.255.255 tcp 0 0
static (inside, outside) tcp x.x.x.12 7777 NVAPP01 7777 netmask 255.255.255.255 0 0
static (inside, outside) tcp x.x.x.12 8080 8080 NVDEV02 netmask 255.255.255.255 0 0
static (inside, outside) tcp smtp 192.168.1.2 x.x.x.12 smtp netmask 255.255.255.255 0 0
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 x.x.x.12 1
Route inside 192.168.1.2 255.255.255.255 192.168.1.1 1
Timeout xlate 0:05:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server RADIUS (inside) host 192.168.1.2 nvegvpn timeout 5
AAA-server local LOCAL Protocol
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Config seems good. You have made a < clear="" xlate=""> ?
Take care this will reset the translation of the entire table and all users will lose your sessions.
sincerely
Patrick
-
PIX 506 - How to clear the counter on interfaces?
Hello
Can anyone advise on how to delete counters interface on the PIX 506 running version 6.1 (2)?
TIA.
PF
You are welcome. Please mark this more closely
-
Need advice choice btw 2 routers for a pix 506
Hello world. We have a 506th pix we use for firewalls and VPN (access users to home) attached to a Hub to SBS 2000 Server.
Here's my scenario.
DSL---> router Netopia---> Cisco Pix506e-->--> SBS200 hubs.
We are in the process of upgrading from a DSL line to a T1 internet connection, the T1 provider offers the Cisco 1721 router and my Adviser suggested the Cisco 1841. My question is what is the best according to your experience and my script? The T1 provider does not the 1841. Are there limitations with the vs 1721 the 1841? What is the difference BTW the 2 products, and which is the best?
Thank you for your excellent support.
Denise
Hi Denise,
I would use the PIX VPN endpoint. The 506e can do 16 Mbps 3DES throughput and 30Mbps throughput AES is clearly the best box for work, although he only software-based encryption. You can get a VPN hardware encryption for the 1721 module, but since you already have the PIX, why bother?
Hope that help - rate pls post if it does.
Paresh
Maybe you are looking for
-
Can I run Skype through FireFox/Mozilla without installing Skype on my laptop?
My laptop runs Windows Vista Edition home premium (SP2) and Windows Installer does not so I am unable to install or uninstall applications such as skye. As a result, I'm looking for a way to run Skype so that I can't install it normally. Is add a plu
-
I got this laptop PC in 2012, it is a series of G7, I'm pretty sure. My problem is that when I turn the computer off and turn it back on, there is no option to open the menu of the bios (esc) or any option besides. Just a symble blue HP directly in t
-
How can I check the ink levels on a Deskjet 6540 using Win 7? Is a "Toolbox" available?
-
XP OEM reinstall with only CD Key
So my hard drive died in my dell and I have no restore CD/DVD. I had a picture on my dead hard drive that worked. but now what. How can I get a copy of xp with only the product key?
-
World of BB App blackBerry watch that I have no applications
I opened the world Blackberry to search for updates, but it says that I have no applications installed on my phone. I also slected the "available" tab and it says I have none is available. I have several apps on my Q10 which are still usable on my ph