Help with Cisco PIX 506th

Similar Questions

• Help with vpn pix 501

  I'm setting up a cisco pix 501 vpn tunnel but will have questions. The Firewall works although I am able to get out of the internet, but the VPN does not work. On the primary side, I see that the tunnel is up and the traffic is sent but not received.

  Currently I'm sitting at the secondary location but don't know what the problem maybe. Anyone know what I have wrong which could prevent the data to send from this device?

  Here is my config

  Here's my config if it would help

  See the race
  : Saved
  :
  6.3 (5) PIX version
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 2KFQnbNIdI.2KYOU encrypted password
  2KFQnbNIdI.2KYOU encrypted passwd
  hostname ciscofirewall
  domain hillsanddales.com
  fixup protocol dns-length maximum 512
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol rsh 514
  fixup protocol rtsp 5
  fixup protocol rtsp 55
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25

  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list 101 permit ip 192.168.80.0 255.255.255.0 192.168.50.0 255.255.255.0
  192.168.80.0 IP Access-list sheep 255.255.255.0 allow 192.168.50.0 255.255.255.0
  in_outside list access permit tcp any host 192.168.50.240
  in_outside list access permit tcp any host 64.90.xxx.xx
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  IP address outside 66.84.xxx.xx 255.255.255.252
  IP address inside 192.168.80.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  location of PDM 192.168.50.0 255.255.255.0 outside
  location of PDM 192.168.80.2 255.255.255.255 inside
  location of PDM 192.168.50.0 255.255.255.0 inside
  location of PDM 182.168.80.0 255.255.255.255 inside
  location of PDM 0.0.0.0 255.255.255.0 inside
  location of PDM 0.0.0.0 255.255.255.255 inside
  location of PDM 192.168.80.5 255.255.255.255 inside
  location of PDM 192.168.80.7 255.255.255.255 inside
  PDM logging 100 information
  history of PDM activate

  ARP timeout 14400
  Global 1 interface (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Route outside 0.0.0.0 0.0.0.0 66.84.xxx.x
  Route inside 192.168.50.0 255.255.255.0 192.168.50.240 1
  Timeout xlate 0:05:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + 3 max-failed-attempts
  AAA-server GANYMEDE + deadtime 10
  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS 3 max-failed-attempts
  AAA-RADIUS deadtime 10 Server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.80.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  <--- more="" ---="">

  Permitted connection ipsec sysopt
  Crypto ipsec transform-set esp-3des esp-md5-hmac aptset
  aptmap 10 ipsec-isakmp crypto map
  correspondence address card crypto aptmap 10 101
  card crypto aptmap 10 peers set 64.90.xxx.xx
  card crypto aptmap 10 transform-set aptset
  aptmap interface card crypto outside
  ISAKMP allows outside
  ISAKMP key * address 64.90.xxx.xx netmask 255.255.255.255
  ISAKMP identity address
  ISAKMP nat-traversal 20
  part of pre authentication ISAKMP policy 10
  ISAKMP policy 10 3des encryption
  ISAKMP policy 10 md5 hash
  10 2 ISAKMP policy group
  ISAKMP life duration strategy 10 86400
  Telnet 192.168.80.2 255.255.255.255 inside
  Telnet 182.168.80.0 255.255.255.255 inside
  Telnet 192.168.80.5 255.255.255.255 inside
  Telnet 192.168.80.0 255.255.255.0 inside
  Telnet 192.168.80.7 255.255.255.255 inside
  Telnet timeout 5
  SSH timeout 5
  management-access inside

  Console timeout 0
  dhcpd address 192.168.80.2 - 192.168.80.33 inside
  dhcpd dns 64.90.xxx.xx 64.90.xxx.xx
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  dhcpd allow inside
  Terminal width 80
  Cryptochecksum:01532689fac9491fae8f86e91e2bd4c0
  : end

  Hello

  At least the NAT0 ACL is not in use

  You should have this added to the configuration

  NAT (inside) 0 access-list sheep

  -Jouni

• Support stand not provided my replacement WRT-ngn350 - need help with Cisco contact

  Hello!

  I'm starting to feel like Michael Douglas in the movie Falling Down and need help.

  History:
  Finally, I sent to my bad WRT-ngn350 router and when I got the replacement of all but the plastic leg support has been included. I want to have my router stand up to save desktop space, but now I have no foot.

  "OK, should not be difficult to get Linksys to send me the missing foot stand" was my thought. Now, I called the online RMA and also emailed them and I get a similar response as Michael Douglas took with a smile

  I hear that I can't get the part because it is not on the list the content of the product. As this is * my * problem. I want the part and do not care if it's on a list or not. It is the part on the router in the image. I even asked the representative of Linksys to Google a little bit WRT-ngn350 and there are foot stands on almost all of the images and it is certainly included in the box. I was told that I could go nowhere elsewhere to help with that. I really some doubt but fail to find a channel of Linksys, which may be able to help.

  

  If some representative of Linksys sees this please help me!

  Thanks, Niklas

  RMA XXXXX - lack of router support/foot

  (Mod Note: under the guidance of the compliance of the directive.) E-mail deleted conversation.)

  SOLVED!

  The representative of Linksys has managed to dig a booth for me to a warehouse. It is mentioned that it is a unique thing because some parts should be sent. Don't forget to remove the stand and send only: router, power and eventually cable NW.

  Thanks to Linksys representative.

• wrt160n with cisco pix and isa server 2004 config

  Hello

  I am installing a configuration to which my wrt160n router should work, but it is not at present

  .. the is the problem:

  Internet proxy - pix cisco - ms isa 2004 - 4 network cards <> lan1, lan2, dmz and wlan networks

  The wlan network card will only be my lan wireless for internet access interface. The isa server wireless lan nic has been configurered with an IP 10.0.10.1. / 24

  Configure the interface to internet wrt160n with static ip 10.0.10.2 / 24 and bridge 10.0.10.1 2 i'net addresses of dns.

  My dhcp server config is 192.168.100.x /255.255.255.0 and the same dns addresses i'net 2. NAT is disabled because isa server nat for all networks

  where is mistaken or do I forgot something... Help, please

  Activate NAT on the WRT or add a static route for 192.168.100.0/255.255.255.0 to 10.0.10.2 on your isa server computer.

  Of course, you only want wireless, there is not need to use the WRT as a router. You can set the WRT back to DHCP on internet settings. Set the address LAN IP of 10.0.10.2 with a mask of 255.255.255.0. Disable the DHCP server on the WRT. Then one of the LAN wire ports of the WRT to the ISA Server. Do not use the internet port on the WRT!

  Now, you have configured the WRT as simple access point. So you should use your ISA Server to serve DHCP IP addresses inside 10.0.10.0/24...

• Several connections of client XAuth of PIX 506th

  Hi, we have Cisco PIX 506th, fully updated:

  Cisco PIX Firewall Version 6.3 (5)

  Cisco PIX Device Manager Version 3.0 (4)

  We have two customers with Cisco (routers with VPN and PIX firewall IOS). I can't make two IPSec connections for them using XAuth (they allowed Xauth). I see that we have only one VPN connection with extended authentication (XAuth) called "Easy VPN. When I am trying to set up a new one it replaces just my old connection. If I shouldn't use this firewall PIX Easy VPN Client, how can I use extended authentication (XAuth) I found no option for this? Is this supported? At 25 connections how to only IPSec connections without XAuth authentication data sheet?

  as far as I know, you may need an additional device. as mentioned, the reason being a single unit can act as a client for two ezvpn ezvpn different servers.

  Otherwise, you must return to the type of vpn. that is, to set up lan - lan.

• VPN site to Site with NAT (PIX 7.2)

  Hi all

  I hope for more help with config PIX.  TBH I would classify myself as a newb on PIX, only dabbling in it every 6 months or so...

  I have to configure a VPN site-to site between our UK and US Office, to replace our frame relay link.  I have configured multiple VPN site to site on the before PIX, so am reasonably okay with the appearance of the config of who.  What is a new concept for me is the needs of NAT'ing between the IPSEC tunnel.

  The U.S. Agency requires us to NAT source addresses (i.e. 192.168.1.0) usable on their side address (i.e. 143.102.89.0).  The tunnel must then be set to encrypt traffic between 143.102.89.0/24 and 172.24.0.0/14.

  I added the following config and hoping to test it at the U.S. office happens online today.

  If I Ping from 192.168.1.0 to 172.24.x.x source and run a SH NAT inside, the NAT translation seems good.

  is the intellectual property inside 192.168.1.0 255.255.255.0 outside 172.24.0.0 255.252.0.0
  static translation at 143.102.89.0
  translate_hits = 4, untranslate_hits = 0

  Could someone please go through the following lines of config and comment if there is no error?

  Thank you very much

  Kevin

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 cm 5.4pt cm 0 5.4pt ; mso-para-margin : 0 cm ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;}

  IP 143.102.89.0 allow Access-list ipsec - dallas extended 255.255.255.0 172.24.0.0 255.252.0.0

  policy-nat-dallas-list of allowed extensive access ip 192.168.1.0 255.255.255.0 172.24.0.0 255.252.0.0

  public static 143.102.89.0 (inside, outside) - list of access policy-nat-dallas

  Crypto ipsec transform-set esp-3des esp-md5-hmac 3desmd5set

  card crypto map dyn 40 correspondence address ipsec - dallas

  set dyn-map 40 crypto map peer 143.101.6.141

  card crypto dyn-map 40 transform-set 3desmd5set

  dyn-map interface card crypto outside

  crypto isakmp identity address

  crypto ISAKMP allow outside

  crypto ISAKMP policy 10

  preshared authentication

  3des encryption

  md5 hash

  Group 2

  life 86400

  tunnel-group 143.101.6.141 type ipsec-l2l

  IPSec-attributes tunnel-group 143.101.6.141

  pre-shared-key *.

  You can configure NAT/Global pair for the rest of the users.

  For example:

  You can use the initially configured ACL:

  policy-nat-dallas-list of allowed extensive access ip 192.168.1.0 255.255.255.0 172.24.0.0 255.252.0.0
  NAT (inside) 1 access list policy-nat-dallas

  Global 1 143.102.89.x (outside)

  The static statement that you configured previously will take precedence over the above. So the printer gets statically using a NAT to 143.102.89.10, and the rest can do another ip address 143.102.89.x PATed.

  Please note that for PAT, traffic can only be initiated from 192.168.1.0/24 LAN to 172.24.0.0/14, not the other way around.

  Hope that helps.

• Need help with configuration on cisco vpn client settings 1941

  Hey all,.

  I just bought a new router 1941 SRI and need help with the configuration of the parameters of the VPN client. Orders aspect a little different here, as I'm used to the configuration of ASA and PIX for vpn, routers not...

  If anyone can help with orders?

  I need the installation:

  user names, authentication group etc.

  Thank you!

  Take a peek inside has the below examples of config - everything you need: -.

  http://www.Cisco.com/en/us/products/ps5854/prod_configuration_examples_list.html

  HTH >

  Andrew.

• Help with customer 501 pix for the configuration of a site...

  Hello everyone, I am trying to set up a customer vpn site and after a few days

  I'm at the end of the roll.

  I'd appreciate ANY help or trick here.

  I tried to set up the config via CLI and PDM, all to nothing does not.

  Although the VPN client log shows the invalid password, I am convinced that the groupname password is correct.

  I use the Cisco VPN Client 5.0.07.0290 v.

  -----------------------------------------------------------------

  Here is HS worm of the PIX:

  Cisco PIX Firewall Version 6.3 (5)
  Cisco PIX Device Manager Version 3.0 (4)

  -----------------------------------------------------------------

  Here's my sh run w / passwords removed:

  pixfirewall # sh run
  : Saved
  :
  6.3 (5) PIX version
  interface ethernet0 10baset
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate the encrypted password to something
  that something encrypted passwd
  pixfirewall hostname
  domain ciscopix.com
  fixup protocol dns-length maximum 512
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol they 389
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list ping_acl allow icmp a whole
  permit 192.168.1.0 ip access list inside_outbound_nat0_acl 255.255.255.0 192.168
  . 50.48 255.255.255.248
  outside_cryptomap_dyn_20 ip access list allow any 192.168.50.48 255.255.255.248

  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  IP address outside pppoe setroute
  IP address inside 192.168.1.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  IP local pool vpnpool 192.168.50.50 - 192.168.50.55
  history of PDM activate
  ARP timeout 14400
  Global interface 10 (external)
  NAT (inside) 0-list of access inside_outbound_nat0_acl
  NAT (inside) 10 0.0.0.0 0.0.0.0 0 0
  Access-group ping_acl in interface outside
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Sip timeout - disconnect 0:02:00 prompt Protocol sip-0: 03:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  AAA-server GANYMEDE + 3 max-failed-attempts
  AAA-server GANYMEDE + deadtime 10
  RADIUS Protocol RADIUS AAA server
  AAA-server RADIUS 3 max-failed-attempts
  AAA-RADIUS deadtime 10 Server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.1.0 255.255.255.0 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
  Dynamic crypto map outside_dyn_map 20 match address outside_cryptomap_dyn_20
  Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-3DES-MD5 value
  map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
  outside_map interface card crypto outside
  ISAKMP allows outside
  part of pre authentication ISAKMP policy 20
  ISAKMP policy 20 3des encryption
  ISAKMP policy 20 md5 hash
  20 2 ISAKMP policy group
  ISAKMP duration strategy of life 20 86400
  vpngroup address vpnpool pool vpnaccessgroup
  vpngroup dns 192.168.1.1 Server vpnaccessgroup 192.168.1.11
  vpngroup wins 192.168.1.1 vpnaccessgroup-Server
  vpngroup vpnaccessgroup by default-field local.com
  vpngroup idle 1800 vpnaccessgroup-time
  something vpnaccessgroup vpngroup password
  Telnet 192.168.1.0 255.255.255.0 inside
  Telnet timeout 60
  SSH 192.168.1.0 255.255.255.0 inside
  SSH timeout 5
  Console timeout 0
  VPDN group pppoe_group request dialout pppoe
  VPDN group pppoe_group localname someone
  VPDN group ppp authentication pap pppoe_group
  VPDN username someone something
  dhcpd address 192.168.1.100 - 192.168.1.110 inside
  dhcpd dns 206.248.154.22 206.248.154.170
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  dhcpd allow inside
  Terminal width 80
  Cryptochecksum:307fab2d0e3c5a82cebf9c76b9d7952a
  : end

  -----------------------------------------------------------------------------------------------

  Here is the log of pix in trying to connect with the client vpn cisco w / real IPs removed:

  crypto_isakmp_process_block:src: [cisco vpn client IP here], dest: [cisco PIX IP here] spt:64897 TPD:
  500
  Exchange OAK_AG
  ISAKMP (0): treatment ITS payload. Message ID = 0

  ISAKMP (0): audit ISAKMP transform 1 against 20 priority policy
  ISAKMP: encryption AES - CBC
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 256
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 2 against priority policy 20
  ISAKMP: encryption AES - CBC
  ISAKMP: MD5 hash
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 256
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 3 against priority policy 20
  ISAKMP: encryption AES - CBC
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: preshared auth
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 256
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 4 against 20 priority policy
  ISAKMP: encryption AES - CBC
  ISAKMP: MD5 hash
  ISAKMP: default group 2
  ISAKMP: preshared auth
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 256
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 5 against priority policy 20
  ISAKMP: encryption AES - CBC
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 128
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform against the policy of priority 20 6
  ISAKMP: encryption AES - CBC
  ISAKMP: MD5 hash
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 128
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform against the policy of priority 20 7
  ISAKMP: encryption AES - CBC
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: preshared auth
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 128
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 8 against priority policy 20
  ISAKMP: encryption AES - CBC
  ISAKMP: MD5 hash
  ISAKMP: default group 2
  ISAKMP: preshared auth
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP: keylength 128
  ISAKMP (0): atts are not acceptable. Next payload is 3
  ISAKMP (0): audit ISAKMP transform 9 against priority policy 20
  ISAKMP: 3DES-CBC encryption
  ISAKMP: hash SHA
  ISAKMP: default group 2
  ISAKMP: long-acting prior auth (init)
  ISAKMP: type of life in seconds
  ISAKMP: lifespan (IPV) 0x0 0 x 20 0xc4 0x9b
  ISAKMP (0): atts are not acceptable.
  crypto_isakmp_process_block:src:src: [cisco vpn client IP here], dest: [cisco pix IP here] spt:64897 TPD:
  500
  ISAKMP: error msg not encrypted
  crypto_isakmp_process_block:src: [cisco vpn client IP here], dest: [cisco pix IP here] spt:64897 TPD:
  500
  ISAKMP: error msg not encrypted
  pixfirewall #.

  ---------------------------------------------------------------------------------------------------------------

  Here is the log of the vpn client:

  363 16:07:58.953 01/07/10 Sev = Info/4 CM / 0 x 63100002
  Start the login process

  364 16:07:58.953 01/07/10 Sev = Info/4 CM / 0 x 63100004
  Establish a secure connection

  365 16:07:58.953 01/07/10 Sev = Info/4 CM / 0 x 63100024
  Attempt to connect with the server '[cisco pix IP here]. "

  366 16:07:58.953 01/07/10 Sev = Info/4 IKE / 0 x 63000001
  From IKE Phase 1 negotiation

  367 16:07:58.969 01/07/10 Sev = Info/4 IKE / 0 x 63000013
  SEND to > ISAKMP OAK AG (SA, KE, NO, ID, VID (Xauth), VID (dpd), VID (Frag), VID(Nat-T), VID (Unity)) [cisco pix IP here]

  368 16:07:59.078 01/07/10 Sev = Info/4 IPSEC / 0 x 63700008
  IPSec driver started successfully

  369 07/01/10 Sev 16:07:59.078 = Info/4 IPSEC / 0 x 63700014
  Remove all keys

  370 16:08:00.110 01/07/10 Sev = Info/4 IKE / 0 x 63000014
  RECEIVING< isakmp="" oak="" ag="" (sa,="" vid(xauth),="" vid(dpd),="" vid(unity),="" vid(?),="" ke,="" id,="" non,="" hash)="" from="" [cisco="" pix="" ip="">

  371 16:08:00.110 01/07/10 Sev = WARNING/3 IKE/0xE3000057
  The HASH payload received cannot be verified

  372 16:08:00.110 01/07/10 Sev = WARNING/2 IKE/0xE300007E
  Failed the hash check... may be configured with password invalid group.

  373 16:08:00.110 01/07/10 Sev = WARNING/2 IKE/0xE300009B
  Impossible to authenticate peers (Navigator: 915)

  374 16:08:00.110 01/07/10 Sev = Info/4 IKE / 0 x 63000013
  SEND to > ISAKMP OAK INFO (NOTIFY: INVALID_HASH_INFO) [cisco pix IP here]

  375 16:08:00.110 01/07/10 Sev = Info/4 IKE / 0 x 63000013
  SEND to > ISAKMP OAK INFO (NOTIFY: AUTH_FAILED) [cisco pix IP here]

  376 16:08:00.110 01/07/10 Sev = WARNING/2 IKE/0xE30000A7
  SW unexpected error during the processing of negotiator aggressive Mode:(Navigator:2263)

  377 16:08:00.110 01/07/10 Sev = Info/4 IKE / 0 x 63000017
  Marking of IKE SA delete (I_Cookie = A152D516B07D9659 R_Cookie = 5F4B55C38C0A40F4) reason = DEL_REASON_IKE_NEG_FAILED

  378 16:08:01.078 01/07/10 Sev = Info/4 IKE/0x6300004B
  IKE negotiation to throw HIS (I_Cookie = A152D516B07D9659 R_Cookie = 5F4B55C38C0A40F4) reason = DEL_REASON_IKE_NEG_FAILED

  379 16:08:01.078 01/07/10 Sev = Info/4 CM / 0 x 63100014
  Could not establish the Phase 1 SA with the server "[cisco pix IP here]" due to the "DEL_REASON_IKE_NEG_FAILED".

  380 16:08:01.078 01/07/10 Sev = Info/4 IKE / 0 x 63000001
  Signal received IKE to complete the VPN connection

  381 16:08:01.078 01/07/10 Sev = Info/4 IPSEC / 0 x 63700014
  Remove all keys

  382 16:08:01.078 01/07/10 Sev = Info/4 IPSEC / 0 x 63700014
  Remove all keys

  383 16:08:01.078 01/07/10 Sev = Info/4 IPSEC / 0 x 63700014
  Remove all keys

  384 16:08:01.078 01/07/10 Sev = Info/4 IPSEC/0x6370000A
  IPSec driver successfully stopped

  Mmmm... What version of vpn client do you use?

  If you use the last being, it looks like you might have it downgrade to a version older than the version of your PIX is old enough.

• Help with logs on Cisco router

  First of all: if I'm in the wrong place, please let me know.

  Question: I'm digging orders Cisco, but the help of Cisco, Googe, Yahoo Sites and other types of resources can not give me the answer I wanted.

  Router: Cisco 7206VXR (NPE - G1) processor (revision C) with 983040K / 65536K bytes of memory.

  My question is simple and pleasant: I need to learn from the history of the Interface of one of our routers and not being is not in the domain of Cisco for a few years I can't find command. If I can find a command that draws a complete history that would be great.

  The commands I used:

  history

  history of show

  car1. Ash #sh interfaces se1/0/23:0 history
  ^
  Invalid entry % detected at ' ^' marker.

  car1. Ash #show interface se1/0/23:0 60 minutes story
  ^
  Invalid entry % detected at ' ^' marker.

  I need to find the command that gives newspapers the following type:

  00:00:46: % LINK-3-UPDOWN: Interface Port-Channel, 1 changed State to
  00:00:47: % LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed State to
  00:00:47: % LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed State to
  00:00:48: % LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, state change downstairs
  00:00:48: % LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed
  State down 2 * 1 Mar 18:46:11: % SYS-5-CONFIG_I: configured from console by vty2
  (10.34.195.36)
  18:47:02: % SYS-5-CONFIG_I: configured from console vty2 (10.34.195.36)
  * 18:48:50.483 Mar 1 UTC: % SYS-5-CONFIG_I: configured from console vty2 (10.34.195.36)

  What you are looking for is not available using interface show orders but would be available using the show log command. You want something that could look like this

  view Journal | include 1/0/23:0

  Note that this is the search through the buffer of logging on the router. The amount of memory allocated to the record buffer and the volume of messages generated will determine how far back you can go. If the router sends syslog messages to a syslog server (or another feature of management that archive messages) then you can search the logs it and to go further back. Also note that the logging buffer is cleared when the router reloads.

  HTH

  Rick

• With the help of Cisco ACS 5.2 (GANYMEDE +) with other than Cisco devices

  Hi all

  I was hoping that someone could help me with what might be a silly question. I'm trying to implement a solution whereby an operator can control all their nodes (other than Cisco) network via GANYMEDE + involved nodes are

  Juniper M10i running Junos 9.2, M120

  M320 running Junos 8.5 Juniper

  Extremes of BD8810 and BD8806 running 12.4.1.17 XOS

  3804 Alpine extreme Extremeware 7.8.3.5 running

  My question is, can I use Cisco ACS 5.2 (or 4.2) to authenticate using GANYMEDE + to these other than Cisco devices. Has anyone else done this or I have to use RADIUS? If someone has done this are problems of interoperability with Cisco CS and Junos or XOS extreme. Thank you

  / John

  John,

  We have a very large deployment of Juniper (T-series, series MX, etc.). We use Cisco ACS and GANYMEDE to manage these devices. The configuration of the ACS is fairly simple. You'll want to create users to connect and match them to the classes on your JUNOS routers. Here is an example:

  set system login user uid of engineering 2000
  Set system login user engineering genius-class class
  set the connection user uid to NOC 2001 System
  Set system login user AC AC-class class

  define the system connection Engineering-class idle-timeout 15
  define a connection system class engineering-class permissions all
  define the system connection AC-class idle-timeout 15
  define the connection class AC system class view permissions
  Set connection AC-class permissions see the system configuration

  We use two classes of genius and NOC. One is defined as a read / write and the second read-only. This is in turn then mapped in ACS (in our case version 4.2) by user or group (preferred). First, you change the configuration of the interface and add a Ganymede junos-exec service and do not enter the Protocol field. Then, you change the attributes of the user group. I've attached screenshots for both on this subject.

  Hope this helps.

  Derek

• Connectivity random Cisco Pix 501

  Hello. I'm having some trouble with my CISCO PIX 501 Setup.

  A few months I started having random disconnects on my network (from inside to outside). The machines can ping the DC or the Pix, but impossible to surf the internet. The only way to make them go outside is a reboot of Pix.

  My configuration is:

  -----------

  See the ACE - pix config (config) #.
  : Saved
  : Written by enable_15 at 09:23:07.033 UTC Tuesday, June 3, 2014
  6.3 (3) version PIX
  interface ethernet0 car
  interface ethernet1 100full
  ethernet0 nameif outside security0
  nameif ethernet1 inside the security100
  activate 8Ry34retyt7RR564 encrypted password
  2fvbbfgdI.2KUOU encrypted passwd
  hostname as pix
  domain as.local
  fixup protocol dns-length maximum 512
  fixup protocol esp-ike
  fixup protocol ftp 21
  fixup protocol h323 h225 1720
  fixup protocol h323 ras 1718-1719
  fixup protocol http 80
  fixup protocol pptp 1723
  fixup protocol rsh 514
  fixup protocol rtsp 554
  fixup protocol sip 5060
  fixup protocol sip udp 5060
  fixup protocol 2000 skinny
  fixup protocol smtp 25
  fixup protocol sqlnet 1521
  fixup protocol tftp 69
  names of
  access-list acl_out permit icmp any one
  ip access list acl_out permit a whole
  access-list acl_out permit tcp any one
  Allow Access-list outside_access_in esp a whole
  outside_access_in list access permit udp any eq isakmp everything
  outside_access_in list of access permit udp any eq 1701 all
  outside_access_in list of access permit udp any eq 4500 all
  outside_access_in ip access list allow a whole
  pager lines 24
  Outside 1500 MTU
  Within 1500 MTU
  outside 10.10.10.2 IP address 255.255.255.0
  IP address inside 192.168.100.1 255.255.255.0
  alarm action IP verification of information
  alarm action attack IP audit
  history of PDM activate
  ARP timeout 14400
  Global 1 10.10.10.8 - 10.10.10.254 (outside)
  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
  Access-group outside_access_in in interface outside
  access to the interface inside group acl_out
  Route outside 0.0.0.0 0.0.0.0 10.10.10.1 0
  Timeout xlate 03:00
  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
  Timeout, uauth 0:05:00 absolute
  GANYMEDE + Protocol Ganymede + AAA-server
  RADIUS Protocol RADIUS AAA server
  AAA-server local LOCAL Protocol
  Enable http server
  http 192.168.10.2 255.255.255.255 inside
  http 192.168.10.101 255.255.255.255 inside
  http 192.168.100.2 255.255.255.255 inside
  No snmp server location
  No snmp Server contact
  SNMP-Server Community public
  No trap to activate snmp Server
  enable floodguard
  Permitted connection ipsec sysopt
  ISAKMP nat-traversal 20
  Telnet timeout 5
  SSH 192.168.10.101 255.255.255.255 inside
  SSH timeout 60
  Console timeout 0
  dhcpd dns 8.8.8.8 8.8.4.4
  dhcpd lease 3600
  dhcpd ping_timeout 750
  dhcpd outside auto_config
  Terminal width 80
  Cryptochecksum:7f9bda5e534eaeb1328ab08a3c4d28a
  ------------

  Do you have any advice? I don't get what's wrong with my setup.

  My DC is 192.168.100.2 and the network mask is 255.255.255.0

  The network configuration is configured to set the IP of the gateway to 192.168.100.1 (i.e. the PIX 501).

  I have about 50 + peers on the internal network.

  Any help is apprecciate.

  Hello

  You have a license for 50 users +?

  After the release of - Show version

  RES

  Paul

• Active FTP problem between Checkpoint and Cisco PIX

  Hello

  I am facing a strange problem.

  Many of our customers have achieved a Checkpoint FW-1/VPN-1 4.1 SP6 (the last before NG). When they try to connect to an FTP server that is located behind a Cisco PIX firewall, they are not able to transfer data: the connection is established, the authentication to follow, but at the stage of the 'LIST' the connection 'freeze' and the user must close the FTP client.

  Users are facing this problem ONLY in Active mode: passive mode works very well. Turn passive mode FTP client isn't acceptable workaround for most of my clients.

  The problem seems to be related only to the firewall Cisco PIX and active FTP.

  Please, what is someone encountered the same problem?

  Could someone give me any help?

  Thank you in advance.

  Paolo

  Yes it is a (global) problem, even with the last checkpoint firewalls. What happens with Active FTP, it's that each command (get, list, etc.) causes another log on the client (source port) to the server on port 21. If you run netstat from the customer you can check this for yourself.

  What normally happens, with HTTP, FTP, telnet, which have are, it's that the client makes a connection to port 21, 23 etc then returns with a port source such as 1936, 1980, 3000, etc..

  Connect problem with statefull firewall is they do not allow multiple sessions control port number on a destination, as well as a source port can be bound to a destination port, in this case, 21 for FTP. I Don t see it changed, an extreme security risk any time soon, since it s, someone else might be hopping session and block this type of traffic, it's what the stateful firewall are all about and FTP servers are problably the machines more pirated on the planet.

  You´ve mentioned the workaround solution, unfortunately that s the only way, change your passive customers, I think that Unix/Linux customers have a problem with this, change your FTP server can also help, there are multiple servers that can be configured to disable Active FTP, I wouldn know exactly, I only network & firewall... maybe someone else can move on this...

• Cisco PIX VPN pass through (sorry, tricky!)

  Hello

  I'm having some problems with allowing IPSEC through a Cisco PIX 501. The configuration is the following:

  Host (mail Client) (192.168.1.111)

  |

  PIX (NAT)

  |

  INTERNET

  |

  (Checkpoint) VPN server

  The problem is, the PIX guard dropping my outgoing isakmp packets on its * internal * inetrface!

  710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp

  710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp

  710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp

  710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp

  710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp

  710005: request UDP and eliminated from 192.168.1.111/500 to inside:192.168.1.1/isakmp

  Does anyone know why it does this? Anyting to my in-house (security level 100) should go directly to my giving and external interface on the net. For some reason, is to treat the isakmp packets differently...

  I have included my config as an attachment, can we see what I missed or have any ideas why it loses the isakmp packets?

  Thanks for any help.

  Nick Chettle

  Check users. C and edit it with your favorite editor. Check if you have a private or public IP address!

  I tried to find in the really safe base article I've seen a couple of months ago but I can't find any more.

  https://SecureKnowledge.checkpoint.com/SK/public/intro.jsp

  See also this FAQ:

  http://www.phoneboy.com/bin/view.pl/FAQs/SecureClientFAQs

  See CheckPoint VPN-1 Guide that is on the installation CD or go to the web site of checkpoints, BUT you need a valid account Center user to read and download the documentation. Start looking at page 119 and 211.

  As usual, nothing is free at the checkpoint.

  http://www.checkpoint.com/support/technical/documents/docs_r55.html

  sincerely

  Patrick

• IKE Dead Peer Detection between Cisco ASA and Cisco PIX

  I have a network environment in Star with about 30 offices of satellite remote using VPN Site to Site connectivity.  The majority of remote satellite offices have the features of Cisco PIX 501 running PIX Version 6.3.  The hub office runs a version 8.2 (1) Cisco ASA.

  I configured Dead Peer Detection on the Cisco ASA device at the office hub with the default settings of the following-

  Confidence interval - 10 seconds

  Retry interval - 2 seconds

  I think I'm right assuming that raises are limited to 3 before the tunnel is completely demolished.  Basically, the problem that I am facing is with several remote satellite offices.  What seems to be the case, the tunnel between the remote offices and the hub is demolished (probably because of the length of IKE, always 86400 seconds) and the tunnel then fails to renegotiate unless traffic is physically forced from the hub office.  The tunnel NOT to renegotiate after satellite office, ONLY the end of the hub; so that means sending traffic to the satellite when the VPN tunnel is out of service, not to renegotiate the tunnel.  The Hub office is a colo and therefore traffic rarely comes to that end, the tunnel remains so down until manual intervention occurs and the ICMP traffic is forced into the tunnel.

  Should the KeepAlive and retry interval settings corresponds to both ends, for example if the two devices be configured for DPD?

  What are the potential pitfalls to the extension of the life of IKE, and this will help or even hinder the problem?

  Thank you in advance for helping out with this.

  Hi Nicolas,.

  I think that the two DPD settings must match on both ends, if these do not match then problems like yours might arise which seems to happen here, is that one end shows a tunnel down, but the other end may not detect it down, we could have to watch debugs, or record two ends to see if this is the case , setting in the meantime ike DPD for same timers could hetlp on.

  In regard to the increase in the life expectancy of IKE, well you just need to be aware that this could allow keys to be discovered since these are not renegotiated unless the tunnel is down on the level of IKE. Other than that I don't see why this would affect you.

• Help with service contracts

  Hello world

  I have a new job as a network administrator. So far, network devices have worked with the default configuration and IOS the factory. The thing is, even if I worked with Cisco devices, I've never had to deal with service contracts. I need to be able to update to IOS and may download different features sets. I don't need support, because it's obviously my job. I have been browsing Cisco's Web site and was lost (tons of links and information...). So, could someone point me in the right direction? Should I ask a sort of documents on my business? Contact the company that sold us the equipment?

  I'd appreciate any help. Thank you.

  Hi Felipe,.

  I suggest that you contact the company who sold you the material.  Probably they also sold the contracts of service with it and can tell you what your service contract number.

  Kind regards

  Cindy Toy

  Cisco Small Business Community Manager

  for Cisco Small Business products

  www.Cisco.com/go/smallbizsupport

  Twitter: CiscoSBsupport