Endpoint VPN IP address

Similar Questions

• Loopback Interface client endpoint VPN Site

  My project consists of 871 router connected to the router soho 3845 network head on the MPLS network unencrypted for data communication. For the Client PC behind router 871 on remote site, they need activate the Cisco VPN client and connect to headend 3845 so that they can access information behind the main switch 6506.

  To reduce to a minimum the installation, I would like to prepare a unique VPN profile for all remote controls. So, I plan on using lo0 int for the VPN endpoint. However, I have found that when the VPN connection is in place on the int lo0, the remote client computer can 'ping' lo0 only, but can not 'ping' all other IP addresses. However, when I set up the connection to the IP address on router 3845, the connection is ok.

  I have attached my config for the VPN and the diagram. Can anyone help?

  Hello

  You need to change your ACL split tunnel:

  FEHD_VPN extended IP access list

  Note * outbound VPN client traffic *.

  IP 10.0.0.0 allow 0.255.255.255 10.65.215.0 0.0.0.255

  Note: Do not know what is the purpose of "allowed host ip host 0.0.0.0 0.0.0.0.

• 'server not found' with an ip but ok with vpn ip address

  Windows 7 for the last days that I get the message "server not found" when I try to access many sites (including using Mozzilla). This happens with ie also. However, when I use a different IP address (via my VPN) everything is OK.
  What is going on?

  Cannot find server - troubleshooting

  • https://support.Mozilla.org/en-us/KB/server-not-found-connection-problem

• on the side of client vpn ip address Apple Server help

  Hello

  i've got server apple running on a mac mini running yosemite and I put it in place for the vpn and everything works well on the server-side and client-side. I have what may be a stupid question so patient with me. When I'm on my machine client and vpn is connected, in order to access the storage disk, I have running on my server I have to enter the static ip address, that I attributed to my server. call 192.168.0.14. My question is: what happens if my router on the client computer affects 192.168.0.14 on a device? This results in a conflict? can I assign a static ip address within a range of numbers greater than my server so it's less likely to happen? I'm worrying about something stupid? I'm doing something wrong? Thanks to a light that you can throw on this dilemma.

  George

  Your network server should not be in the same subnet as the network that you are from the connection.   Which means that subnets 192.168.0.0/24 and 192.168.1.0/24 - is the range 192.168.0.1 to 192.168.1.254 - should be avoided.   Better to use a subnet or block 172.16.0.0/12 one subnet in the 10.0.0.0/8 block.  Usually a 24 (255.255.255.0) subnet somewhere in the range of 172.16.0.1 to 172.31.255.254 or 10.0.0.1 to 10.255.255.254, respectively.

  If you are entering the IP address of your server, then the DNS server is either not properly configured the address IP of the DNS server is not communicated to the VPN client or there is something other odd here.

  If your 'router' - probably a gateway box IP offering a combination of IP, NAT router, firewall, port forwarding, and Server features DHCP - past through apparently, built-in DHCP server IP address then you want set up to prevent it to the addresses that you have assigned statically.   In other words, the DHCP server should not be configured with a pool of available IP addresses that include statically assigned IP addresses.

  If you prefer, you can have your OS X Server act as DHCP server and disable the DHCP service in the IP gateway.

  The features and configuration and management of the gateway box varies.

• SSL VPN IP address other than the IP address of the interface?

  Hi,
  
  Is it possibe to use a differnt IP Address from the same Subnet of OUTSIDE
  
  INTERFACE? Instead of Interface IP Address itself. The Idea behind is,
  
  Clients should not use OUTSIDE Interface IP Address for SSL VPN, but whereas they can
  
  use from the IP Address Pool of OUTSIDE Interface.
  Regards

  Brassart Abbas

  If SSL is completed on an ASA firewall, you can finish it on all other ip addresses but the external interface.

  If it is completed on a router IOS, Yes, you can use a different ip address to put an end to the SSL VPN connection.

  Hope that answers your question.

• Ins easy vpn server address Pool

  Hello

  I have? ve a router cisco 1721 with a single card wic adsl.

  This router gives me nat (dmz servers) and internet connection.

  Now, I need to implement with this router a vpn server that is easy to provide the vpn connection to customers who use the software of cisco vpn client 4.8.

  I followed step by step the instructions to turn on the server but when the wizard tells me an address pool... I do not know.

  The router has 2 addresses fastethernet, 192.168.156.253 and 192.168.158.253 (secondary).

  My LAN works whith 192.168.156.x address.

  What will be the address pool?

  Best regards

  heze54

  Edgar,

  Configure the pool of addresses as something different from these two networks, as I said in my previous post.

  IP local pool vpnpool 192.168.3.1 192.168.3.254

  I hope this helps.

  Thank you

  Gilbert\

  The rate of this post!

• Remote access VPN IP address-lease (Tunnel) question

  Hello

  I'm the Internet connetcted machines for our LAN via the Cisco VPN Client. Termination of IPSec is ASA 5520.

  Physical address is provided by the internet provider to customers.

  Address of tunnel that deliver us from our LAN infrastructure.

  The problem is that if the customer cancels and reconnects VPN, connection always get a new tunnel - address.

  The problem is 'normal' termination (disconnect the vpn client) or when timeout or a breach of Internet customers.

  For administration purposes, we need the customer get the same IP address. Release-time for tunnel-addresses ist located 120 minutes.

  Maybe IPsec cannot handle this?

  v: * {behavior:url(#default#VML) ;} O'Bryan: * {behavior:url(#default#VML) ;} w\: * {behavior:url(#default#VML) ;} .shape {behavior:url(#default#VML) ;} / * Style Definitions * / table.}}}} MsoNormalTable {mso-style-name: "Table normal" "; mso-knew-rowband-size: 0; mso-knew-colband-size: 0; mso-style - noshow:yes; mso-style-parent:" ";" mso-padding-alt: 0 cm 0 cm 5.4pt 5.4pt; mso-para-margin: 0 cm; mso-para-margin-bottom: .0001pt; mso-pagination: widow-orphan; do-size: 10.0pt; do-family: 'Times New Roman' ;} "}

  Thank you very much for the help!

  Martin

  Martin,

  As far as I know, we are unable to change this behavior.

  Let me ask, what would be the purpose of the monitoring of users via the same IP address and not their username?

  What kind of information are you extraction and what kind of information you generate with it?

  Marcin

• ASA - ldap - user vpn static address

  Hello!

  I am trying to configure ASA to assign a static IP even to some user (User1) every time when it connect to the network via the AnyConnect client. We have Windows AD and that you are using the LDAP AAA server for authentication of remote access VPN users. I found in the document 'Cisco ASA 5500 Series Configuration using the CLI, 8.2 Guide' in the explanation section "Configuring external year for security device user permission to the server" and configured the ASA and user properties in AD exectly similarly:

  Firstly, I assigned a static ip address in the menu properties (section numbering) of User1 in Active Directory. Then I created the ldap attribute card where I traced msRADIUSFrameIPAddressattribute to IETF-RADIUS-Framed-IP-Address. attribute In the end, I applied this map to attribute ldap to LDAP AAA server group.

  Although I have implemented this, whenever I connect using User1 received powers AD I always get the ip address of the vpn pool rather a static ip address which I configured. In the output of debugging ldap 255 command I found the line "msRADIUSFramedIPAddress: value =-1062718956 ' but not any line that prove the above attribute map.

  It seems that the mapping does not work.

  All AnyConnect users get the policy settings defined internal group on ASA, including addresses form pool, dns etc server. I want User1 to get a static IP and inherit all other group policy settings.

  If someone has any ideas of how to fix this, please help.

  Thank you

  Hello

  Please give the output of the aaa server hs.

  I found the link that gives you the configuration of the requirement details.

  http://www.Cisco.com/en/us/docs/security/ASA/asa82/configuration/guide/ref_extserver.html#wp1661694

  I hope this helps.

  Kind regards

  Anisha

  P.S.: Please mark this message as answered if you feel that your query is resolved.  Note the useful messages.

• Question of redundancy VPN l2l using 2811 as endpoint devices

  I have a new implementation of VPN L2L passes using two 2811 s than VPN terminal devices. I'll try to use the HSRP address between the public interfaces of both routers as VPN peer address. The problem that I found during the test is that the tunnel will become active and debugs watch the HSRP address as an invalid address to form the tunnel. Have a work-around, or a better plan for redundancy on peering address using similar devices? Thanks in advance.

  Take a look at this doc about IOS IPSec HA.

  http://www.Cisco.com/en/us/docs/iOS/security/configuration/guide/sec_vpn_ha_enhance_ps6922_TSD_Products_Configuration_Guide_Chapter.html#wp1039849

• A Site to remote access VPN behind the same public IP address

  Got a problem quite stupid.  We have a VPN from Site to Site configured for a new data center, which will be responsible for general traffic management.  In addition, some users need to use use a VPN client to access certain areas.  The firewall at the Office only has a public IP address, so the two will come to the Site to Site VPN for remote access from the same source.

  This seems a problem with legacy Cisco VPN clients because encryption card matches the entry VPN site-to-site, even if they use VPN clients.  A good/simple solution to solve this problem?

  Some newspapers (198.18.85.23) is the address public IP for the office and the tom.jones is the user.  192.168.1.0/24 is the pool of the VPN client.

  January 7, 2014 19:12:52 ASA5515: % 713130-5-ASA: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, transaction mode attribute unhandled received: 5

  January 7, 2014 19:12:52 ASA5515: % 737003-5-ASA: PISG: DHCP not configured, no viable servers found for tunnel-group "Corp-VPN.

  January 7, 2014 19:12:52 ASA5515: % 713119-5-ASA: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, PHASE 1 COMPLETED

  January 7, 2014 19:12:52 ASA5515: % ASA-3-713061: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, IPSec tunnel rejecting: no entry for crypto for proxy card remote proxy 192.168.1.4/255.255.255.255/0/0 local 0.0.0.0/0.0.0.0/0/0 on the interface outside

  January 7, 2014 19:12:52 ASA5515: % ASA-3-713902: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, error QM WSF (P2 struct & 0x00007fff28dab560, mess id 0x37575f3c).

  January 7, 2014 19:12:52 ASA5515: % ASA-3-713902: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, peer table correlator Removing failed, no match!

  January 7, 2014 19:12:52 ASA5515: % 713259-5-ASA: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, Session is be demolished. Reason: political crypto card not found

  January 7, 2014 19:12:52 ASA5515: % ASA-4-113019: Group = Corp-VPN, Username = tom.smith, IP = 198.18.85.23, disconnected Session. Session type: IKEv1, duration: 0 h: 00 m: 02s, xmt bytes: 0, RRs bytes: 0, right: not found card crypto policy

  January 7, 2014 19:12:53 ASA5515: % 713904-5-ASA: IP = 198.18.85.23, encrypted packet received with any HIS correspondent, drop

  Hello

  Don't know if this will work, but you can try the following configuration (with the rest of the VPN configuration)

  list-access CLIENT VPN ip enable any 192.168.1.0 255.255.255.0

  card crypto OUTSIDE_map 4 is the VPN CLIENT address

  card crypto OUTSIDE_map 4 set peer 198.18.85.23

  card crypto OUTSIDE_map 4 set ikev1 transform-set ESP-AES-128-SHA ESP-3DES-SHA

  The idea would be to have the ACL matches the VPN full Tunnel that the Client attempts to establish. (destination "any" from the point of view of the customer, the ASAs view source)

  I tested briefly on my own SAA by connecting from an IP address to which the ASA offers free VPN in L2L. But as I don't have the operational L2L VPN, I can't really verify the VPN L2L at the moment. Thus, certain risks may be involved if you can afford it.

  -Jouni

• How to set up a Lan to Lan VPN without using your external IP address?

  I have two 28 subnets A & B.

  My PIX and ASA outside interface addresses are both in A subnet.

  I am in the middle of a migration of the PIX to ASA and need to use the PIX outside of the address of the interface on the ASA for the last two remaining lan to lan VPN.

  I do like that because the sellers of these virtual private networks to connect to are huge dinosaurs IT and the aaages to get their sh * t tri... This means that I have to pass the IP address to my ASA, so I can't sentence have change for a new IP peer.

  I tried to figure out how to set a specific my counterpart VPN IP address but I can't figure out how...

  I even physically connected a second ethernet port and tried to give a similar IP in the same range, which it says it is not possible to have both outside the IP addresses on the same subnet.

  Hello

  It is not possible to have an IP address "secondary" on the physics/logic interface of a Cisco firewall.

  And as you've noticed, you cannot configure the same subnet on 2 different interface either.

  We are talking about such a large configuration that you want to just migrate from completely to the ASA PIX and make a switch during a maintenance window?

  Couldn't you just pass the ASAs 'outside' IP address address to that on the PIX and move the ASAs 'outside' of the PIX? Or not the ASAs "outside" IP address already some configured related to what makes this impossible?

  -Jouni

• Configuration VPN - NAT - T support

  Hello

  A partner of business (BP) has the following requirements. I don't know which statements of config I need to use to ensure this successful connection

  Business (BP) needs partner complete the VPN tunnel on a firewall that is behind another firewall running NAT

  (BP) will create UDP 500 and UDP 4500 endpoints on the NAT firewall which is forwarded to the Firewall VPN termination.

  Because of this, the (BP) needs of my dissertation support encapsulation of ESP over UDP (NAT - T)

  My series of ASA5500 using the code (825) has the statements

  Crypto isakmp nat-traversal 21
  crypto ISAKMP ipsec-over-tcp port 10000

  VPN # match address BP_VPN crypto card
  VPN # set peer (peer_ip) crypto card
  VPN # game of transformation-AES_256_SHA crypto card

  IPSec-l2l type tunnel-group (peer_ip)
  IPSec-attributes of tunnel-group (peer_ip)
  pre-shared key (TBD)

  BP_VPN list extended access permit tcp host 10.x.x.x, 172.16.x.x eq (specified port) host
  BP_VPN list extended access permit tcp host 10.x.x.y host 172.16.x.x eq (specified port)

  NatExempt_VPN list extended access permit tcp host 10.x.x.x, 172.16.x.x eq (specified port) host
  NatExempt_VPN list extended access permit tcp host 10.x.x.y host 172.16.x.x eq (specified port)

  Please indicate whether these statements are sufficient and if not what else would be needed.

  You need not order

  crypto isakmp ipsec-over-tcp port 10000

  It is for the exclusive implementation that was used before NAT - T is available. You only need to nat-traversal active. For your ACL, using ports in there makes everything complicated. You should see if you can just use 'ip' here. If there is already configured on your ASA virtual private networks, then the config is probably ok. If this isn't the case, you must always configure ISAKMP and activate the encryption on the interface card.

• Try to connect to a remote VPN server

  This task was bleeding in my eyes. I can't make it work. I understand the principle of TCP-OUT ACCORD - IN but can't seem to reconcile it kind includes the firewall.

  Long and short of the situation:

  Company a static IP address assigned by the local society of DSL

  All computers inside network enjoy outdoor internet access and interconnectivity

  Remote VPN host has static IP

  Configuration VPN of a properly established and the remote control accounts are active.

  Does not connect when good ID and PASSWORD are entered.

  Anyone tried this before. Please assume that I have the skill level of a child of 5 years and the patience of the same thing.

  Thank you for your help.

  Timothy S. Murray

  A child under 5 huh? looks like a lot of people that I care. I'm kidding anyone, not me flame.

  In any case, we need a little more information here to go, it's a connection to a PIX PPTP you talk, or a router? Or is it IPSec (you mentioned GRE, that's why I think you speak of free WILL). Is the user authentication is done locally on the endpoint VPN device, or is it a server Radius/GANYMEDE involved?

  Can you send in the configuration of the end device, ensuring xxxxx valid IP addresses and passwords?

• L2TP VPN connects but won't see network drives

  Hi all

  I just got a MacBook Pro with El Capitan. I joined it to my area of work and I have implemented SonicWall VPN Client Mobile and I tested it on and it works - only if my network, I am connected to and the VPN will not have the same IP range.

  I would like to use the integrated VPN L2TP client, but I have questions here. I have configurted on my Dell SonicWall and connect this VPN from a remote location, it will connect and show the data transfer (sending / reception are green) but I can not access my network drives.

  Once I have switch back to Mobile Client VPN SonicWall, everything works well.

  Any idea?

  Routing on L2TP or PPTP will probably work or at all, if both ends of the VPN tunnel terminate on the same CIDR network block. Which is why people never give a one VPN server address local 192.168.1.0/24. the network block is much too common. Please use something in 10.x.x.x.

• RV042 VPN public ip

  Hello everyone,

  I ' v bumping my head again and again with this issue... I need to configure a tunnel ipsec VPN with a service provider, they require that the first negotiating phase vpn ip address is public (which is normal "Local Security Gateway") and the need to address public ip for the second phase ("group of Local Security") it is im having problems on the source of the request service must be a public ip address as well. When I created my tunnel with their configuration. I have no problem to have the tunnel connected.

  

  

  

  The problem comes when I have to configure my computer with the public ip address and connect to the RV042 router in order to access the tunnel... So I tried to put a local ip address to my computer lets say 10.1.10.102 and then do a NAT with ip address public xx.xx.xx.37

  When I do this i never send packets from my computer (which is a linux server bdw) through the VPN... and if I give the server the xx.xx.xx.37 address public ip with gateway xx.xx.xx.38 also packages do not go anywhere...

  mainly the problem is to know how to configure my server or gateway to send traffic to my server through vpn! because the tunnel is UP. (remember that the only way that the service provider will acept the connection is with the public ip address on the bridge and on the group.

  OK guys, I just managed to make it work! I just plugged my server on the DMZ port with the public ip address and presto! tour of 1to1 nat!