ePrint with HP Laserjet P1102W

Similar Questions

• Unable to connect to the HP ePRINT with Color LaserJet Pro 400 M475dw MFP website

  LaserJet Pro 400 color multifunction m475dw-Just installed. Print, scan, copy and fax all works fine! use of WiFi

  Using IMAC OS 10.8.2 with all updates

  Netgear DGN2200v3 router using

  Printer not connect to the HP ePrint website

  Printer connects using Hp and profile for fax set up etc.  But the "HP Web Services" article when enrecorded and hit the Activate button - it does not connect to the site - it seems just to refresh.

  "If I try to connect thro the printer not the imac and try to activate the web services, it says" connection "on the screen BUT after a few minutes of trying - so says" CONNECTION ERROR - the printer is unable to connect to the service. Check the internet connection

  ANY IDEAS - HAVE I MISSED SOMETHING?

  Thank you very much

  I try to pull up the built-in web server (EWS) by entering the IP address of the printer in a browser and set a static IP & DNS address.

  The information for the default gateway, subnet mask and IP address can be accessed from the Setup menu on the front panel, go to settings > reports > network summary and it will print off the coast.

  Once you entered the IP address in a browser and have the EWS pulled up, go to the tab above titled "Networking". Then click on IPv4 in the left column; who will bring to the top of the address configuration page.  Place the manual radio button and fill in the IP address, the default gateway and the subnet mask with the information from the report. You don't fill the part entitled WINS server, which can be left alone.

  You will then want to fill in the DNS of the page part, the favorite should be set to 8.8.8.8 and the alternative/secondary must be set to 8.8.4.4. Then click 'apply '.

  Power cycle the printer. Turn off the power, wait 30 seconds and then turn it back on. Once it is fully operational, try again to connect to web services.

• Problem with installing Laserjet P1102W - Ad-Hoc - can't change mode of Communication of Ad Hoc

  I have a printer HP Laserjet P-1102W which was installed in Ad - Hoc mode for a short time.  The unit can, however, connect via USB and works very well in this mode, but I want to use it as a Wifi unit with my router and the APs. The unit has a 20130703 firmware datecode. I need to reset the mode of communication out of the "Ad Hoc" mode.

  With the printer is NOT connected through the USB port and holding down the 'X' button to print the "Self Test / Configuration of the device"sheet shows that the status = not connected. " The MAC address displays address 12 characters, the IP address is 0.0.0.0, as is the subnet mask and the gateway. The "IP configured by Hand with the server DHCP/BOOTP = 0.0.0.0 =. The 802.1 b / g Wireless Status = Enabled and the Communication mode = Ad Hoc, SSID = HP4FA96D with authentication = None (open).

  I tried to reset the unit by pressing down the wireless and 'X' buttons located on the top of the machine, but this action does not change the mode of further Ad Hoc communication. I looked through the USB print driver in Windows 7 Pro, but can find no access to wireless settings, and as the camera doesn't have an IP address, I can't access the built in web server.

  Any suggestions on how to completely reset the unit so the Mode of Communication is NOT "Ad Hoc"?

  Concerning

  IT IS FIXED - READ BELOW:

  After trying the patches recommended by other users, download the latest firmware, the driver more current and also help in the HPPSdr.exe of the HP program, making a unit restart by pressing both buttons when the device has been propelled to the top (this is only a partial and not completely reset reset) the unit would not clear the AD - Hoc mode and return to the wireless infrastructure mode.

  The last step, I tried (without the help of HP or the community) was to find the original disc of 2009 and first install it like a USB connected printer. If successful, then a second set with USB cable attached as a wireless printer. It helped me finally change the settings DHCP wireless, assuming, SSID, etc.. Once completed, and unplugged the USB cable, the printer now works as a printer wireless assuming with my router and access points.

  We have NOT ALLEGED on HP support pages for this printer trying to use older software install the disc and make a several step installation - shame on HP!

  The community of HP came with some good ideas, suggestions did not fix of unfortuantely this problem. The printer is out of warranty, so HP Corp. would NOT  provide any help (by e-mail or otherwise) unless I used either the HP community or pay them $24.95 for once call phone support. It seemed stupid to pay 25% of the new value of the printer four years ago.

  Given this bad experience with the lack of support for current HP products which exceeded their warranty period, I can't recommend HP products to my clients or friends. Shame on HP for this contempt for their customers!

  Peter

• Printing with Hp laserjet P1102w wireless problems

  Hi, I have problems printing wireless on my macbook with Hello. I set up the printer and it prints ok. But after awhile, it loses comunitcation. I always turn off my router to reset everytime I need to print. I tried the printer of the assign a static IP address, but it still does the same thing.

  Hello

  To address the issue of Hello, probably it depands on your router, will be helpful to know your router brand and model to better understand the reason.

  To work around the problem, you can also set the printer by IP, in my view, it should help:

  1. Go into System Preferences > Print & Fax or printing & scanning.
  2. Click on the Plus sign to add a printer.
  3. Click the icon of the IP above.
  4. Select the HP Jetdirect Socket Protocol.
  5. Type the IP address of the printer.
  6. Confirm and will create a new queue.

  Print using the print queue newly created, listed as the IP address of the printer.

  Kind regards

  Shlomi

• HP LaserJet P1102w: I do not know my email address for HP EPrint

  Hello

  I have a HP Google Chromebook 14 and I try to my HP LaserJet P1102w EPrint.  I did not initially set up this printer and I need email EPrint to print.  How to find this e-mail address?

  Such an IP address is wrong and will not allow access to the content, the printer or the printer connected to the network.

  Try turning off the printer, make sure it is not located too far away from your router has HOWEVER also ensure there is no less than 1.5 to 2 meters between the printer and the router.

  Turn off the printer, once it is off restart your router by unplugging its power for 10-15 seconds.

  Once you plug in the back of the router allow it 1 to 2 minutes until all lights turns on and you are able to access internet from your chromebook.

  Only, then turn on the printer and leave it a few moments to connect until the blue light turns blue.

  Then print another check for the difference.

  If you see all these addess that starts with 169.254 once again, please specify your model of router, also make it clear if you have any other computer available (this is in order to understand our options if necessary to reconfigure the connection of the printer wireless as such can be done directly from Chrome OS)

  Please let me know the results,

  Shlomi

• ePrint with Laserjet 1536dnf

  Eprint works with 1536dnf Laserjet?

  In the case where it does how to find the email address of my printer?

  Thank you

  GAL

  galhayut wrote:
  

  Eprint works with 1536dnf Laserjet?

  In the case where it does how to find the email address of my printer?

  Thank you

  GAL

  LaserJet printers supported include:

  HP Color LaserJet Pro CM1415 series	All over the world	X	X
  HP Color LaserJet Pro CP1525 series	All over the world	X	--
  HP Color LaserJet Pro M1536 series	All over the world	X	--

  It seems that your printer can be supported, although I have to admit that I'm not 100% familiar w/LaserJet models.  You must confirm that your is part of the printers HP Color LaserJet Pro M1536 series, it seems that it is.

  If it is supported, you can follow these steps to activate ePrint in the post below:

  http://h30434.www3.HP.com/T5/eprint-print-apps-mobile/how-to-remove-amp-re-enable-Web-services-on-LaserJet-printers/TD-p/409291

  An update of the firmware may be necessary to add support for printing on LaserJet printers at the moment, before you can activate ePrint.

• HP Laserjet P1102w: Compatibility with WIndows 10

  Currently running Windows 7 and have 2 HP laserjet P1102w to consider a new computer with Windows 10 - HP will have a driver that will allow me to continue to use these printers?  I couldn't get a definitive answer on the HP site.  Thanks in advance for any help.

  Linkwriter wrote:

  My astonishment was the word 'Pro' does not appear in the description of my printers equipment - is equivalent to this printer the HP Laserjet P1102w?

  Hello

  HP Laserjet P1102w, normally to Pro.

  Kind regards.

• LaserJet P1102w: Laserjet P1102w cannot activate the installation with Windows Vista 32 bit PC computer wireless

  Hello forum HP, I can use the Laserjet P1102w with USB connection on 3 different devices including a portable Apple and PC Windows Vista and Windows 7 laptop computer, but can not perform a wireless installation with the broadband internet connected wireless PC running Windows Vista 32 bit. The main message is that the computer does not find the printer even when using the USB connection. Any help would be appreciated.

  Hi @Kaiser3107,

  Welcome to the HP Support forum.

  I understand that you have a HP LaserJet Pro P1102w printer that connects three thin devices via the USB port, but you can not perform a wireless installation on a fourth device, equipped of Windows Vista 32-bit, because the PC does not detect the printer via the USB port. I would like to help with that.

  Here is a support document which includes 'USB device is not detected by Windows' which can help the issue of detection - Troubleshooting (Windows Vista) USB connections.

  Please let me know if that solves the problem, or if you need assistance.

  In fact, if it helps you to find a solution, please click on the 'accept as Solution' and the 'thumbs up' buttons down below in this message.

  Thank you!

• HP laserjet p1102w does not work with Mac computer version 10.8

  Since I upgraded my Mac to 10.8 operating system, I'm not able to use my printer HP Laserjet P1102W ePrint. I was told that the current version of the 20130213 firmware does not support this feature. Anyone know when the new version of the firmware will be available to support this feature? Thank you very much.

  Manual, please let me know the result.

• LaserJet p1102w: how to access the interface web printer with new router

  I just bought a new wireless router, hoping that I'll be able to more easily print with my p1102w.

  Internet access works ok desktop and laptop (wireless).

  However, I had bookmarked the IP address of my printer, and before, I've always been able to access it by clicking on the bookmark. I checked the range of IP addresses for the router, and the IP of the printer is outside this range, so I don't know why I am no longer able to access to this. I can't access the web interface, whether they come from my laptop or desktop (wired). However, the printer is capable of printing from the desktop without problem.

  How do I enter this? I would like to restart the configuration wireless configuration, but I thought I needed the web interface for this.

  I should just insert the CD? I made a tweak or two and would prefer to keep all the settings of the printer even if I can, but I can start all over again if I have to.

  
  HP LaserJet p1102w

  I just deleted the printer on my laptop computer, reset the settings of the printer default and then run Setup from the wired desktop wireless utility wireless. Seems to have worked, I can now access the web interface via my laptop now.

• HP laserjet 5n: Eprint with printer inherited?

  Hello

  I have an old, heavy but reliable hp laserjet 5n, which works flawlessly for personal impression in my family. It is connected to the router (orange france livebox) via ethernet. Several win 7 and computers portable win10 print through this old workhorse.

  now, I wanted to add to the versatility, being able of eprint with smartphones and tablets.

  I installed the applications on android and ios, but the printer is not on the local network. Enter the help of t address 192.168.1.18 didn't either.

  is it hopeless, or everyone has managed such a facility?

  thx for your help

  hgenet

  Hello

  The printer is not supported by the HP ePrint app, only printers listed below are supported:

  http://support.HP.com/us-en/document/c02814760

  You can check for a 3rd party application like PrinterShare that allow to share the printer since through your wqith Apple or Android devices:

  http://PrinterShare.com/

  Kind regards

  Shlomi

• LaserJet P1102w: Address in the wrong place on the envelope of 6 3/4 with LaserJet P1102W

  When I print 6 3/4 envelopes in Word since my Windows 7 64-bit system to a new LaserJet P1102w address is correctly centered from top to bottom, but it is so far to the left half of the address is cut off from the envelope. The same settings printed correctly with my old HP LaserJet 1022nw printer.  Can HPW I fix?

  Bear with me a moment... My printer is a different model than yours, but here's what I discovered. Firstly a bit of background. My old HP B209 printer would print envelopes card without problem, but when I started using my printer HP Photosmart 6520, it would just spit in the envelope without printing the addresses, even if I chose an envelope of greeting card in the printer properties. HP could not solve my problem and other sources on the HP Forum said that HP just made a blunder in designing is not the printer to print envelopes of greeting cards.

  Finally after a year or two, a member of the HP Forum suggested I have try select the C5 envelope in printer properties and that is, the envelope printed however; the address printed back ok but send it to the address has been out of the envelope with only a partial address display. For some unknown reason, I selected 'options' on the printout of the envelope (a feature I've ever used) and learned that I could work out where the return address and send it to the address were located on the page. When you click the 'Options' button you can adjust the situation where each address appears on the page. You change the 'top' and 'left' numbers you can watch address icons (which appear as straight lines) are moving on the envelope. Pass each address around there where you want it and then try to print the envelope. If each address is too right or too far left or should be raised or lowered just play with the settings until the addresses where you want. Write your settings on a piece of paper and stick it on the side of your computer tower or someother convenient place so you can store these settings in the future.

  Now... don't forget to change the envelope size to the default envelope size you are using in general. I always use a #10 envelope business for my personal correspondence. Otherwise, the next time you go to print a standard envelope (what size is that you are using) the parameters will always be in place for the envelope of 6 3/4 that you use and addresses does not print correctly. You will not need to change the settings of your default envelope size because it will always go to the value by default (unless you change it) hope this solution works for you.

• Problem with the HP Laserjet p1102w printer

  Hello

  I have the problem that my printer HP LaserJet p1102w (wireless) still print on the same page, no matter what I send to print. Curretly I can't print at all because every time when I turn on the printer starts infinitely print the same page...  I tried to reinstall the drivers, but it did not help.

  How can I solve this problem? Can I do hard reset somehow?

  Thanks in advance for any help with this problem!

  You don't mention whether or not you have recently installed your printer on a network, but this is a HP document that answers your question, once the product is installed on a network of troubleshooting.  Please let me know if it helps.

  Product print permanently the same print job

  Tobindo

  A representative from HP

• HP LaserJet P1102w: Windows 8.1 - run two different USB connected P1102w printers with simple shortcut on the desktop?

  I am trying to set up a single laptop Windows 8.1 for someone who uses it according to the seasons in two locations (FL and MY). I installed a HP LaserJet P1102w printer in each location. I wish I had a printer that is connected USB (one at a time will be connected) able to access in an only menu icon Office or file print command.

  When you add the second printer, Windows8.1 recocognized, the driver is already installed, he apparently recognizes the different addresses MAC and/or numbers of series of different printers and present second printer on the page devices and printers in Control Panel or allow a second printer on the desktop icon.  The only way to tell apart printers is that one is listed as a Hewlett-Packard LaserJet P1102w and the other is listed as a HP LaserJet P1102w. It is rather confusing to the elderly person who will be using the laptop.

  Is it possible to have the mobile exploit any printer is connected both by means of a simple print command or icon? Maybe by connecting via a WSD Port Monitor?

  Thanks for any help or advice!

  Dave Waters

  Hey @dmwaters138,

  Welcome to the Forums of HP Support!

  I understand that you do not want to have two HP LaserJet Pro P1102w printer operation via USB Wired on 1 single machine with a single order of printing or the icon. I would like to help you with the configuration of this option today. Because there are two distinct Laserjet on Windows 8.1 computer printers, to do two icons impression for various devices. The best way to tell the difference between the two devices is to rename printers. Thus, when the client goes in file and print in the print dialog window, simply choose the printer name that corresponds with the device they want to print to. You can rename printers all you want. Install printers on the WSD Port wireless network would give the same result of having two copies of the printer is installed on the computer. One thing I see, is that the name of the HP Laserjet Printer is unusual. It seems that your printers may be using the built in Windows drivers, rather than the HP Full Feature driver package for the device. This may cause printing conflicts in the future. Can I please you follow the steps below to set up and install both LaserJet HP correctly.

  Step 1: Remove the drivers:

  It is crucial that your HP LaserJet are using the correct HP driver package. So I'll have you remove two copies of your HP Laserjet of the computer. Please make sure that the USB cables are connected.

  1. Open the screen, Start by selecting the Windows icon at the bottom left of the computer screen or by selecting the Windows key bottom left of the keyboard, to the right of the Ctrl key
  2. In the start screen, type devices and printers. Click on devices and printers
  3. In devices and Printers window please right click on the Hewlett-Packard Laserjet and select delete device or delete. Once this copy is a party, please right click on the HP Laserjet P1102w and select 'remove device' for this one as well. After have removed two copies of the Laserjet please close devices and printers.
  4. Then, on the Start screen type programs and features. Click on programs and features to launch the window
  5. Scroll the list of programs and find the HP Laserjet driver package. If you see the HP Laserjet printers select Uninstall. Please follow the prompts on the screen to complete the uninstallation. Once the uninstall is complete, please close programs and features and continue to the next step.

  Step 2: Remove temporary files:

  1. Open the screen, Start by selecting the Windows icon at the bottom left of the computer screen or by selecting the Windows key bottom left of the keyboard, to the right of the Ctrl key
  2. In the start screen, type run. Click on Run to launch the run dialogue box
  3. In the run box, type %temp% , and then click OK
  4. When the Temp folder opens, select Ctrl + A at the same time on your keyboard. Everything in this folder will highlight now.
  5. Select the "delete" button on your keyboard. The Temp folder contains the temporary internet files. None of the actual files or folders on your computer will be affected by deleting Temp files. A Temp file should you will automatically get the pop up to 'jump' this point.
  6. Close the Temp folder when it is empty
  7. Right-click the recycling bin on your desktop and select empty recycling bin. Please proceed to the next step.

  Step 3: Install devices:

  1. Please leave unplugged USB cables

  2. Please click here to download the package full feature software and driver for the HP Laserjet Printer

  3. when the download is complete, please follow the instructions on the screen to install the first Laserjet. Make sure you select the 'install the printer software ' tab connect the USB cable only when the installation window prompts to.

  

  4. Once installation is complete for the first printer, please open the Start screen and type devices and printers.

  5. once the devices and printers opens, you will see the first copy you installed HP Laserjet. Please right click on the HP Laserjet Printer , and then select printer properties

  

  6. under printer properties , you will see the name of the printer on the general tab at the top. Please rename the printer to something that the customer acknowledges that this first printer. Then click on apply and then OK to save the changes.

  

  7. close devices and printers

  8 open the Start screen again. This time, type run. Click on Run to launch the run dialogue box.

  9. in the run box type %temp% , and then click OK. The Temp folder is now open

  10. in the Temp folder to locate the 7z... file. Click this folder to open it. This is the HP Installer package for HP Laserjet printers. Scroll to the bottom of this file and double left click on the P1100_P1560_P1600.exe driver package. The installation program will now open.

  

  11. in the title of the installation window, select "Add another printer. Don't connect not the USB at the moment. Click Next.

  

  12 connect the USB cable for the second printer once the installation window invites you to. After the second installation, please open the Start screen.

  13. in the start screen, type devices and printers. Click on devices and printers to open the window.

  14. in the printers and devices window, you will now see a second copy of your HP Laserjet. Right-click on the new copy and left click on properties of the printer. When the Properties window opens please rename the second copy of your printer. Click on apply then OK to save the changes.

  

  15. close devices and printers

  When the customer print, in the print dialog window they will just now to choose the name of the printer that fits the HP Laserjet Printer they wish to print to.

  

  I know that sounds like a lot of steps, but I wanted to give you as much detail as possible to ensure that this process goes well for you.

  Please let me know if the steps I have provided to resolve your problem. Good luck!

• How do I copy/scanning with my printer laserjet P1102w

  pls tell me where to go to get this info

  Hello sandyains

  The Laserjet P1102w lacks a scanner. So, he can not scan or copy.

  HP LaserJet Pro P1102 printer Specifications product