Equium A60-692 restarts after closing the lid

More annoying, the only thing I can do is hold the power button to turn off & on again. Is there a key combination should I put pressure to bring its edge form after you have closed the lid, or is it a fault?

Thank you


Usually when the size of the memory changes, the system can recover.

Remove the battery and the AC adapter / CC, and then remove one of the memory Modules and power on.

Tags: Toshiba

Similar Questions

  • I am expierencing problems with my isight Camera on my MacBook Pro. Suddenly the video camera does not start (no green light on) FT or Photo Booth. The screen is black, if I restart computer it works but after closing the lid, it stops. V10.11.3

    I have problems with my view i camera on my Mac Book Pro. Suddenly the video camera does not work (no green light on) FT or Photo Booth. The screen is black, if I restart it, it works but after closing the lid it stops and I have to restart the computer.  I use V10.11.3. An idea about what is happening

    Hello mpm068,

    Thank you for using communities of Apple Support.

    Since your iSight webcam works up to the time that your Mac goes to sleep, I would like you to start please help desk trying to replicate this problem then to reboot in safe mode:

    1. Choose the Apple menu > shut down.

    2. After your Mac stops, wait 10 seconds, then press the power button.

    3. As soon as you hear the startup tone, hold down the SHIFT key.

      You must press the SHIFT key as soon as possible once you hear the startup tone, but not before.

    4. Release the SHIFT key when you see the gray Apple logo and progress indicator.

    To exit safe mode, restart your Mac, but no press during the startup.

    OS X El Capitan: start in safe mode

    Take care.

  • Restart the problem after closing the lid of the laptop for a few minutes

    I use Windows 7 Home Premium on my Asus A53S. I have reboot issues a few minutes after closing the computer laptop lid eventhough I put what to do after closing the lid to "do nothing" for both on battery and the plug. And it will keep restarting over and over again. Rest

    Hi DennisHii,

    You did changes to the computer before the show?

    Method 1
    I suggest you perform the clean boot and check if the problem persists.

    How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
    Note: Follow step 3 of section of boot KB929135 to reset the computer in normal mode.

    Method 2
    I suggest you try the steps from the following link:

    Windows 7 is not going to sleep

    Hope this information is helpful and let us know if you need more assistance. We will be happy to help.

  • Tecra M7: Tablet does not work after closing the lid

    Someone had problems with the Tablet does not work after closing the lid on a Tecra M7? BIOS is 3.20

    Does not happen on hibernate or sleep.
    I have the set cover to do nothing on close.


    What do you with Tablet does not work after closing the lid?
    Is - what the laptop freezes or what? What happens exactly?

    Closing the parameters adjustable lid to Hibernate or standby mode or no action.
    These settings can be defined in configuration power saver actions.

    If you have some problems with some Toshiba applications installed, I recommend you to reinstall the program and TOSHIBA common Modules that doesn t work properly!

    Best regards

  • Tecra 9100: Sleep Mode is no longer enabled after closing the lid


    First post here and not the smartest when it comes to computer skills...

    Have a Tecra 9100 about 4 years old, under XP Pro SP2.

    last 3 days whenever I close the lid of the laptop it won't STAND BY mode me leaving no option but to propel to the top and I get "SUMMARY FAILURE PRESS ANY KEY."... »

    I changed any settings whatsover and since then, I tried to access the Power Saver icon in Control Panel, but when I click on it nothing happens. I then click on a few of the Control Panel Power Options and I get the message "...". "a Microsoft power options and use the Toshiba power Saver saver" which obviously I can't access either!

    Is there any reason why closing the lid of my laptop is no longer 'Stand by' mode, basically going in OFF format only, it became a major drawback and don't know where to turn to.

    Any help or advice would be greatly appreciated.
    Thanks in advance.


    Reading your post I guess windows on own power options and doesn t use Toshiba power saver power profiles.

    Generally, the issue should be resolved by switch again to the Toshiba power saver in the-> power options control panel! But your announcement about turning the power on, it is not possible! It s very strange?  :|

    In this case, I recommend to remove the Toshiba installation energy saver. This can be done in the Add & Remove programs.

    So finally, check out the following steps:
    Remove the energy saver, restart the laptop, reinstall the Toshiba Common modules, reboot the laptop and install again the energy saver.

    After this procedure, the splash screen should work! By the way; the hibernation mode is disabled by default. If you want to use the Hibernate mode, you will need to enable it first!

  • Satellite L500 - external screen display after closing the lid?

    I use the Satellite L500 - 120 Notebook, and before installing Windows 7, the laptop has a function very uncomfortable, when I applied an external display.
    When I closed the lid of my laptop, Office was shown on my display (with the native resolution of the external display) external, so I had not to
    change anything on the control panel. In Windows 7, Miss me this feature. I already tried to use the Control Panel, but there is no parameters, which fits
    with the previous ones. I can duplicate the screen in order to see my desktop screen on my external screen, but with the resolution of 1366 x 768 laptop.
    If I extend the views, then there is only the background image to the external screen, but this time with the native resolution.

    So my question is, how to conifgure Windows to recognize that I closed the lid, and the screen should be shown on my external screen?
    Or should I install applications Toshiba, that I had before, who visited account this function?

    Thanks for any help!


    I m not a Windows 7 user because I want to wait until it will be released official, but I hope that I can help you a bit:

    First of all in power management, you can choose the action that happens if you close the lid (g. e. sleep, close, etc.). This action must be disabled because otherwise the laptop shuts down or something else.

    So I think that you need to install the display driver for your laptop. You can try the Vista driver because most of them are working on Windows 7.
    Then you should be able to define the correct screen resolution for external monitor.

    A working display driver is important to the clone or extends monitors to verify this!

  • Windows error recovery received CONSTANTLY after closing the lid

    I did a factory reset using the recovery a month ago discs.  When I was using the system at this time as I closed the lid.  When I came back to it at a later date, I opened the lid and noticed that it was not on.  I pressed the power button and received the following message is displayed:

    Windows error recovery

    Windows is not shut down successfully.  If it was because of the system does not, or if the system was stopped down to protect data, you might be ale to recover by choosing one of the Safe Mode configurations from the menu below:

    (Use the arrows to select your choice.)

    Safe mode
    Safe mode with networking
    Safe mode with command prompt

    Start Windows normally

    What is the problem and how can I fix this so it doesn't happen or is this normal with Vista.

    Hi SouthernDixieCowgirl,

    This would happen if the driver graphics card on the computer is damaged or needs to be updated.

    You will need to update the drivers to display on the computer card by visiting the manufacturer of the card or the computer manufacturer's website and check if it works.

    Updated a hardware driver that is not working properly

    http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly


    Also, make sure that you install drivers chipset update by contacting the manufacturer of the computer.

    I hope this helps!

    Halima S - Microsoft technical support.

    Visit our Microsoft answers feedback Forum and let us know what you think.

  • Qosmio G20-127: failure to screen after closing the lid on Vista


    I have a Qosmio G20-127 and I recently installed Vista Ultimate (32 bit). I managed to put everything in its place (except the magic buttons, but the drivers are not on yet), but I have a problem that makes me seriously reconsider coming back to XP MCE.

    When I close the lid of my computer, the screen turns off of course, but when I open again, it does not turn, but it stays black. And I can't turn it on again no matter what. I have to turn off the entire computer and it is quite unrealistic.

    Funny is that after a restart for about 20-30 minutes, I can open and close the lid normally, but the same problem occurs after a bit more time to work on the computer.
    The problem persists even though I disabled everything remotely connected to the closing of the cover.

    Does anyone have a solution?

    Hello English

    Try you update the BIOS on the VISTA OS?

    I can imagine you will always find something new and unusual, but please note that Vista is not supported by the OS for Qosmio G20 (Vista drivers are not available on the Toshiba download page) and you can expect that from time to time, you will discover new disturbing behavior.

    I recommend you to install and configure Vista as described in the topic of s Francisco, configure OS for your needs, and be happy if you use Vista without any serious problems. In my opinion, for OS installation and configuration software Qosmio is Toshiba laptop more complicated template, and you will never be able to configure it as a supported and preinstalled WXP MCE. Commands supported are tested and bugs are fixed, but not with Vista on Qosmio G20.

    Sorry my friend. Sounds stupid, but maybe that's just the truth. By the way: I like Qosmio G20. Maybe I'll buy one if the price is Ok.

    Good bye

  • Satellite L300-1FS - Wireless reconnect after closing the lid


    My 2 month old son Toshiba laptop works very well in many ways, but an annoying problem, is that if we close the lid when you open it again it doesn't re connect to our router. If I click on the network connection, it just says: there is no everything!

    Sometimes the switching market re wireless switch will connect there, but more often than not, it's a reboot, which is annoying.

    Proves that the wireless card works but it would be nice to not have him harass me every time it does not connect.

    All ideas welcome.


    First a question: what exactly happens if you close the lid?
    This laptop stops, or goes to stand-by or extended sleep?

    However, in your case, I would try to update the driver WLAN and the BIOS. Check the Toshiba website for updates:
    http://EU.computers.Toshiba-Europe.com > support & downloads > download drivers

    It would be interesting to know what operating system you have and if you are running the factory settings or you have installed another OS?

    A friend told Satellite L300 and he is very satisfied and can t notice any problem. :)

  • Equium A60 keeps restarting after installation of the graphics driver ATI

    I have installed the Toshiba ATI graphic driver, but when I restart the laptop, it does not start, keeps restarting before surposed to go on windows XP. Help, please.


    Try please solve it as described on this Microsoft article http://support.microsoft.com/?kbid=293078

    Generally, the display driver installation should help. As you know sometimes it is not easy to fix this kind of problem and sometimes is much better recovery procedure.

    You can not write about any common problem if you n t know exactly why this happens. If you are recovering the unit it will be working well. A negative influence on the graphic can have some games preinstalled or many other additional software.

  • No battery indicator and the laptop does not shut down after closing the lid

    After returning from my lapyop return to caused by a virus factory settings I can't have my defiler of battery on my taskbar

    and also I got my lap top programmed to close on the cover but can't find where to put in place


    I suggest you to visit the web link below to change the change the power button cover option.


    Once you have visited the link above, try the method to display the power plan options and then search forcover and the power button and choose your preferred option.

    Hope the helps of information. Please post back and we do know.

  • Satellite L10-232: black screen after closing the lid.


    I moved my laptop (satellite L10-232) in another room, it wasn't stop (just closed it). When I opened it there was nothing on the screen and the battery is not empty (processor still does some things). Anyone know how I can fix this problem?

    Thank you

    PowerManagement is weaker and less stable features on any laptop. (especially with the defective batteries).
    NEVER try to count on the home screen etc. It will work time 999 and 1000 it don't.
    Now, you're done with a laptop computer hanging.
    The ways:
    1. the easy way:
    -push the power button and keep your finger on it for 10 seconds. (5 is enough, 10 to be sure)
    -remove the battery
    -plugin powercable
    -push the powerbutton

    2. the less gentle way:
    -remove the power cable
    -Remove the battery
    -wait 24 hours
    -Insert the power cable
    -push the power button

    trying to understand hat is the startup key sequence to reset the BIOS at startup. (it should be described in your manual somewhere)

    4. the hardest way:! ONLY BY A PROFESSIONAL!
    The laptop must be open and all batteries must be removed. All the capacitors must be emptied (leaving a laptop without the battery for 72 h). Then turn on
    the laptop.

    Please note that I can't be held responsible for any damage or loss of data under any circumstances.

  • Equium A60-157 freezes after inserting the DVD

    Hi all
    When I insert a dvd in the carpet * a DVD-Ram UJ-820 dvd my laptop ram player freezes (sometimes) I am running WinXP SP2 with nero 6 reloaded and dvd shrink it started before the loading of dvd shrink, I'm on AOL.

    This could be a problem?

    Hi Paul,.

    You don't say what kind of DVD that you use in your laptop. You try to play a prerecorded DVD or you load a blank and ready for recording?

    Nero 6 includes a utility called INCD that usually runs at boot time and is designed to detect and format blank disks when they are inserted (or possibly it could be invoked manually). It is possible that this is suspended and causing your notebook to 'freeze '. Make sure you have the latest versions of the product placed on the web site AHEAD NERO 6.

    Kind regards

  • SP U400 - cannot return to the desktop after entering in the mode 'sleep' by closing the lid

    Satellite Pro U400 V-11 I used for a week. I don't know if this is a problem or I did something wrong. My setting of closing the lid is recording mode "Eve" in Vista.

    When I close the lid and open a few minutes later it's ok, I see the password login screen. But if the computer is in "sleep" for a while it does not return to the office when I lift the lid. The screen is black. Fan started working then quiet several times.

    The first three LEDs on the left are green. Keyboard does not respond. And also switch / stop does not work either I press once on or hold it. And only after I unplug the power adapter and press the power, it works. But it restarts the system and Windows could not close correctly the error message is displayed.

    Is this normal or something wrong with the mode 'sleep'?
    Thank you


    I read on some of the similar problems regarding "standby" mode and the black screen.
    Someone suggested to update the BIOS and the display driver

    So I highly recommend it too much
    See the European driver of Toshiba page, choose the model right for laptop and try to update the BIOS, then the display driver.

    Reboot the laptop and see if the problem still occurs.

    Good luck

  • What are the cards WiFi are Equium A60-692-compatible?

    Hi all
    I have a Toshiba Equium A60-692 (model: PSA67E-001001EN). It has a wifi, lid at the rear for a wifi card, but I can't seem to find a list of anywhere where wifi cards are compatible. Someone would be able to provide me with a list of compatible cards!

    Some people said that the Toshiba Equium A60-692 does not support a Wifi but as there is a sign for one at the back I guess that it is wifi ready! In the connectivity for the Athros Wizard, he says also there a 1394 connection, but it does not have a card.

    I found a few on ebay and I want to know if they will be compatible:

    (1) Toshiba 802. 11a / g Wireless LAN Mini PCI Card - Netzwerkkarte, Mini PCI - 802. 11 b, 802. 11A, 802. 11 g, PA3298U-1MPC

    (2) Toshiba WLAN Mini PCI PA3300U-1MPC 54 megabit 802.11 g/b

    (3) TOSHIBA WLAN MINI PCI 54 Mbps 802. 11a / b PA3273U-1MPC

    (4) Toshiba PA3300U-2MPC card WiFi Kit 802.11 g 54 Mbps NEU

    Thank you for your time and I look forward to your responses!


    Post edited by: neilsalexander


    If s said Atheros has a connection 1394 so I guess this means that the firewire.
    The IEEE 1394 mean the firewire connection available on this laptop.

    Anyway, the WiFi network is not available and if you want to use WLan technology on your laptop if you use the WLAN USB key. It is the simplest way to connect to the wireless LAN.

Maybe you are looking for