Error 1920 nvtlservice was able to start
Error 1920 nvtlservice could start when you try to install the Virgin Mobile Broadband 2 GB Air card. Any ideas?
Hello
Reinstalling Windows is the last resort to solve any problem. I suggest you to contact Virgin for help on the issue. Link, you can check: https://www1.virginmobileusa.com/about/prepareEmailUs.do
Tags: Windows
Similar Questions
-
original title: cannot share internet
I shared my internet via ad-hoc, using my wifi in my laptop running vista 64-bit. It just stoped working and now I get a message saying
"an error occurred while internet connection sharing was being enabled. the dependency service or group was able to start. »
Hello
You can view the article in the Microsoft Knowledge base and check if it helps.
Error message when you try to connect to an ad-hoc connection in Windows Vista or Windows 7: "Windows cannot connect to"
" "»http://support.Microsoft.com/kb/946481
Let us know if you need more assistance.
-
I installed Office 2010 on my computer with Vista and now can't connect via cable or wireless. I get the error message: unknown connection status. The dependency service or group was able to start. I know that the router and the wireless work. I tried several of the mentioned patches, but nothing has worked. My Verizon card works.
Hello Chelen,
I suggest you visit this Microsoft TechNet thread where they discuss the same problem you are having:This response may be useful:"I also had the same problem and the solution above does not work.My problem was caused by corruption in the TCP/IP stack
To fix, you need to run a command as administrator prompt
Start > all programs > Accessories > prompt (right click and run as administrator)
At the command prompt, type: netsh winsock reset
"Ignore all errors, restart and voila'.
-
WLan AutoConfig was able to start with the error 193:0xc1
Former title: error 193:0xc1
My wireless does not connect because it says that the WLan service failed to start.
I went to the computer > manage > services > WLan AutoConfig. It has been set to automatic but it was empty when he should have said start. When I tried to start it I got the message service was able to start and the error in the title.
I opened the dependencies in order to check if that was the problem and each of them have begun. So, it seems that the error is always in WLan AutoConfig.
I tried the system restore (this problem just started today) to an earlier point, last week. It sticks on the system restore is initializing an hour +. I tried several restore points, but it always gets stuck on initialization.
I looked at similar questions and I did everything recommended in people, but it seems that the answers stop without the original poster saying that they got it to work or not.
Hello
Step 1.
Follow the steps below and check if the problem is resolved:
a. Click Start, and then click computer.
b. go on the system disk, where the operating system is installed (usually drive C :).
c. find the program file.
d. remove this file and restart the computer and check if you are able to start the service.Note: If you don't see the program file check if the file is hidden. Clickhere to find out how to show hidden files.Step 2.
If the steps above to solve the problem I highly recommend to run a Virus Scan online.
Sometimes the security program installed might not be fair enough. I also recommend you update your security software regularly.
a. follow the link below to start the free online scan:
http://OneCare.live.com/site/en-us/default.htm
b. run the malware removal tool from Microsoft.
Microsoft Malicious - 32-bit removal tool
http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en
Microsoft Malicious removal tool - 64 bit
http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en
I hope this helps.Thank you, and in what concerns:
Shekhar S - Microsoft technical support.Visit our Microsoft answers feedback Forum and let us know what you think.
If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly. -
I hope it helps someone as it has been a persistent problem for some time at least six months. I did the research almost as long and also a solution for this, but I'm done here as a last resort. My question to had is that I believe that this occurs at the start of most of the time with the system, but can occur later also is originally the system will block also up and we have four other systems here that this was never a problem at all. I'm still looking and I hope to find an answer somewhere with out having to do a complete clean reinstall 7. I looked here for answers and met several all through the web, including here none have solved the problem. I would be grateful at least someone leading me in the right direction on this issue if you can.
Hope this is the right place to post also. If this isn't the case, please advise.
Journal name:
Source:
Date:
Event ID:
Microsoft - Windows - Kernel-also racingl Admin
Microsoft - Windows-Kernel-EventTracing02/06/2013 -07:59:57
2
Task category: Session
Level: error
Keywords: Session
User: SYSTEM
Computer: BarbKeenan-bail
Description:
Session "circular kernel context Logger" was able to start with the following error:
OxC0000035
EventXmI:
BDB6-4648-BC92-F3FDC74D3CA2}"> I >2 O 2 2 12 Ox80000000000000 1 O I > 2713 I > I > Microsoft-Windows-Kernel-EventTracing/Admin
BarbKeenan - bail I > Kernel context Logger circular
3221225525
268436608
For what it's worth, I have this error periodically on several Windows 7 systems.
She seem to be a non-event and does cause some system problems.
I don't think that your freezing problem is caused by the present.
However, take a look at this thread.
-
Is there a way to eliminate the error "Session"Circular kernel context Logger"was able to start with the following error: 0xC0000035?
Hello A123.
Thanks for the return of the response. Regarding your last question, some were told that they have ignored this error without any problem, but I would like to see if we can fix that. If you start in a clean boot state, you can reproduce this error? I want to see if a program is causing this to happen.
Clean boot:
-
Journal of session "Homegroup" was able to start with the following error: 0xC0000035
Hi my event error log says: session "Journal of home group", was able to start with the following error: 0xC0000035
I don't have a setup of home group because I am the sole operator of my PC. (Windows 7 SP1 x 64).I assume that the error is so wrong? Y/N?If so is there a way to change the reports for this message?Thanks for all the support.Hello
1 are you facing a problem to work with any application because of the error?
2. do you have connected on a network printer?
3. you remember changes to the computer before the show?
I suggest you try the following:
Run a scan of the System File Checker.
http://support.Microsoft.com/kb/929833
Also, make sure that homegroup is not created on the computer, even if the computer is not connected to the other computer. When you configure a network device it will prompt you to create a home group. Check the following link to leave a homegroup.
http://Windows.Microsoft.com/en-us/Windows7/leave-a-HomeGroup
-
Spooler printer error 1068: dependency or group Service was able to start
Original title: Error 1068
I had this problem with error 1068"the dependency service or group could start.
Background - I tried to add a printer that is installed on another PC on the network. When I clicked on add a printer, I get the message. "Windows can't open add printer." The local print spooler service is not running. : rental restart the spooler or restart the machine. "Restart the PC has not resolved it so I did a little research and it said to go to"administrative tools then 'Services' then 'print spooler'. " "I did and when I click on start it flashes a message"Windows is trying to start the service on the local computer"then immediately puts the message 'Windows is unable to start the Service on the local computer print spooler' error 1068: dependency or group Service was able to start.
I tried to do a restore to many dates with no luck at all.
I tried to install the printer directly to the computer... no luck when I went to install the drivers on the CD, I'll even "Windows can't open add printer." The local print spooler service is not running. : rental restart the spooler or restart the machine. "message.
2 local PC repair shops have no idea which will resolve...
Any help will be appreciated operating system is Windows 7 Premium Home edition is installed on an Acer Aspire.
In the default installation, the values must be RPCSS and http. However, it works fine even without http as a dependency. I guess that the http driver is the problem (not start) in your PC, and elimination of the dependence of spooler should do the trick.
-
Hello
Can someone guide me how to solve this error? vCenter service is not getting started, I looked in the newspapers vpxd and found the following error.
vCenter Service was able to start with the error failed to create the front of SINGLE sign-on: vmodl.fault.SystemError
Thank you
John
Hi John,.
This is due to host on the vCenter server entries. Please try the procedure below
Connect to the vCenter server, edit the/drivers/etc/hosts file in Notepad
C:\Windows\System32\drivers\etc\hosts
# 127.0.0.1 localhost
Note: If a line does not exist in the hosts file, add it at the end of the text.
#) to remove the comment from the line of IPv4.
- 127.0.0.1 localhost
· Save and close the file.
- localhost127.0.0.1.
- GoTo services.msc and start VMware Virtual Center Services.
Thank you
Venance
- 127.0.0.1 localhost
-
"dependency service or group was able to start.
I have a laptop with vista. my wireless connection is explained by limited access internet and the icon in the launch area shows "dependency service or group was able to start. I have internet, so I don't know what that means.
Hello
I suggest you to refer to this link and check if it helps:
It will be useful.
-
the dependency of the orgroup faaied to start service unknown Internet connection.
The same day as my expired Norton my internet connection icon says... unknown internet connection. The dependency service or group was able to start. I tried all the suggestions on this page. Can't even find the virus that the internet not connected. My livebox is grateful for the laptop please help
Hello
· You will remember to do recent changes on the computer before this problem?
· Is the question only for the icon network did you try to open a Web page and check?
· What suggestions do you have tried?
· What is the exact error message?
· Have you tried all the steps from the link?
I suggest you follow the steps mentioned below:
Method 1:
Follow the steps in the link and check if the problem persists:
http://support.Microsoft.com/kb/943996
Registry warning:
This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the link below to follow the steps to back up registry:
http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry
Method 2:
If the previous step fails, follow the steps in the link and check if the problem persists:
http://support.Microsoft.com/kb/936211
Method 3:
If the previous step fails, reset WinSock and check if the problem persists:
http://support.Microsoft.com/kb/811259
Registry warning:
This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the link below to follow the steps to back up registry:
http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry
Method 4:
Temporarily disable the norton software (and any other security software) and the firewall on the computer as a test and check if this solves the problem follow the link below:
http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software
If disabling the antivirus software solves the problem, you may need to configure the settings of the antivirus as a result program.
Note: make sure that you enable the antivirus software, other security and firewall programs.
Warning: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.
-
Connection status: unknown. The dependency service or group was able to start.
Greetings! I have a year old Dell Inspiron. Everything worked fine last night, but when I woke today I couldn't connect to the internet. When I put the cursor on the network icon, it says "connection status: unknown." The dependency service or group was able to start. "My Windows Firewall is also disabled and I can't activate it automatically or manually. In addition, the Windows Diagnostic tool cannot be turned on, and whenever I try to activate the Diagnostic Policy Service it also can not be done. It says "error 5: access is denied" when I try to turn it on manually.
My antivirus (Avira) software is fully up to date from last night. I even took it into Best Buy and they did a diagnostic test to ensure that a virus is not the cause. The guy there said it was a software problem. I tried resetting TCP/IP (netsh winsock reset) without success. I also tried sfc/scannow in safe mode and windows without success. Are there other options?
Thanks in advance.
Restore point:
http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/
Do Safe Mode system restore, if it is impossible to do in Normal Mode.
Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.
Try a restore of the system once, to choose a Restore Point prior to your problem...
Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.
See you soon.
Mick Murphy - Microsoft partner
-
When I try to share my internet connection, I get the following error. dependency service or group was able to start
Hi Jason,
1. What is the brand and model of the computer network adapter?
2. How did you try to share the internet connection?
Maybe not all services that run the Internet (ICS) ICS are enabled. I suggest you make sure that the slot addiction services are enabled.
a. Click Start, select run, type services.msc and click OK.
b. to activate a service, look for it in the right pane, double-click its entry.
c. do not forget its Startup Type is set to automatic, and then click OK.
All the following services must be so configured to use ICS:
Application Layer Gateway Service
Network connections
Knowledge of the network (NLA) locations
Plug-And-Play
Remote Access Auto Connection Manager
Remote Access Connection Manager
Remote procedure call (RPC)
TelephonyAfter checking and automatic startup for each of these services configuration, close the Services window and restart the computer before trying again to enable ICS.
I hope this helps. If you have any other queries/issues related to Windows, write us and we will be happy to help you further.
-
Failed to connect to the ESSBASE server &; opmn was able to start
Dear all,
I couldn't connect to Essbase server and a service to opmn works not as well. Hard at this issue not accessible planning application, kindly help us this is very urgent and very crucial for us.
Here are the controls and exit (Please find logs attached):
The message is EASconsole below:
========================
Error: 103: unexpected error Essbase 1030818
Error: 1042006: error network [10061]: unable to connect to [XXXXXXXXXX.
- DS.
- XXXXXXXXXX.
[local: 1423]
Error: 1030818: failed to connect. Please check if the server and port are correct. If you receive timeout or handshake failure, please check if you have tried to connect to secure the port without keyword secure or disable the port with the secure key word.
Of MAXL:
========
Essbase MaxL Shell 64 bit - version 11.1.2 (ESB11.1.2.4.000B193)
Copyright (c) 2000, 2015, Oracle and/or its affiliates.
All rights reserved.
MAXL > connection;
Enter the user name > admin
Enter the password > *.
Enter the host > XXXXXXXXXX
""
ERROR - 103 - Essbase unexpected error 1030818.
Error - 1042006 - network [10061]: unable to connect to [XXXXXXXXXX.d
- s.XXXXXXXXXX.local:1423].
ERROR - 1030818 - login failed. Please check if the server and port are correct.
If you receive timeout or handshake failure, please check if you have tried a bitch
CT to secure without keyword secure or clear with the keyword secure port...
MAXL >
Cmd prompt try everything to start opmn below is the message:
======================================
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:\Users\hyptstadmingdc > cd C:\Oracle\Middleware\user_projects\epmsystem1\bin
C:\Oracle\Middleware\user_projects\epmsystem1\bin > opmnctl status
opmnctl status: opmn is not running.
C:\Oracle\Middleware\user_projects\epmsystem1\bin > opmnctl startall
opmnctl startall: from opmn and managed all process...
opmnctl startall: opmn was able to start.
C:\Oracle\Middleware\user_projects\epmsystem1\bin >
Hi all
Problem was solved after reinstall & reconfig (without uninstalling) box-2, after that I could use planning an application as usual without error.
Kind regards
-
I have a Windows 8 operating system. Whenever I start my PC, I get this error message. BTTray.exe was able to start because BtBalloon.dll is not found, reinstalling the application may fix this problem. I do not even begin to know what is BtBalloon.dll, where can I find it and how do I reinstall. I tried to recover deleted files and reinstal them but there was no improvement. I also tried to do a restore to an earlier date, but she refused.
Help, please.
Reinstall your Broadcom Bluetooth drivers.
Maybe you are looking for
-
How to make an analysis even break?
I want to calculate complaint how I need to sell to brake even?
-
No sound Satellite L300 - 17I - problem with Realtek High Definition Audio
HelloI bought a laptop Toshiba Satellite L300-17I (PSLBCE-00R002GR).After installing WIN XP Prof SP2, I have current drivers downloaded from the Toshiba homepage and installs.It works everything perfectly except the tone!The driver does not work!Can
-
When I'm on google or internet explore everyday and throughout the day, my computer hangs and says the shock wave taken crashed. It's very frustrating, because the system stops and I'm stuck until it starts to run again, which can last from a few sec
-
Hi, I tried to understand why I get system sounds, but I hear no videos or music from the internet. No matter what is the browser, or even if it is itunes. I think it's so weird that I hear system sounds, but nothing else. I have an IDT high defini
-
As indicated in the subject line, all of the lights on the front panel are flashing and nothing works. Will not communicate via cable or wireless. Green light is visible on the power supply. Suggestions?