Error: 382, error: 354, 362, 383 when saving a workflow custom in the database

Similar Questions

• Error 404 - NOT FOUND when you run a form in the form of 11 g

  Hi all
  
  I had this problem when I run the forms using internet explore.
  
  I'm working on forms 11g using weblogic 10.3 for the deployment of web forms.
  
  Error 404 - not found
  RFC 2068 Hypertext Transfer Protocol--HTTP / 1.1:
  10.4.5 404 not found
  Server not found anything matching the request URI. No indication is given whether the condition is temporary or permanent.
  
  If the server does not wish to make this information available to the client, the status code 403 (refused) can be used instead. The 410 (Gone) status code SHOULD be used if the server knows, through a configurable mechanism, that an old resource is permanently unavailable and has no forwarding address.
  
  Can someone tell me where it went wrong.
  
  Thank you

  Let's start by clearing up some confusion.

  PORTS
  --------------
  Version 11.1.1.x here are how the common ports are defined by default:

  1 HTTP Server - 8888
  2 WLS_FORMS - 9001
  3 WLS_REPORTS - 9002
  4 WLS Admin Server - 7001

  So, if you understand how ports work in general, you should see that there are two ways to run a form. You can go through the HTTP server or directly call the WLS_FORMS. This means that both of the following might work, although one would be a direct path and the other is route the request through the HTTP server:

• http://ie1fdtfc5zl1s:9001/forms/frmservlet? config = frmdemo
  
• http://ie1fdtfc5zl1s:8888/forms/frmservlet? config = frmdemo

  Port 7001, will always be the port of the default server for the classic domain administrator. By default, the only thing that you can do from here is EM or WLS Console access.

  As for the question of the AMT, by default, the generator and the runtime will wait to find tnsnames.ora in hospitality \config Instance so be sure you add the correct entries to the correct file.

  You can hardcode a path to the file you want to use by setting TNS_ADMIN in default.env (e.g. TNS_ADMIN = C:\Oracle\mytnsdirectory). This will only apply to execution of forms and not the manufacturer.

  Also, here is something that is often a source of confusion for many people... just because you started your form in the constructor does not mean that the form running has nothing to do with the manufacturer at this time. In other words, when you click RunForm button in the constructor all that you do is pass a url in a browser. The browser and the form do not use the constructor parameters except that can be passed in the URL (e.g. name of user and password). Running of all forms are considered to be 'runtime '. This means that all information environment to an active form configuration must be defined in default.env. The manufacturer, on the other hand will be based on the system variable, the Windows registry (or shell if under Unix).

• Extended analytics. Error when you try to connect to the database

  Hi all
  We created the UDL file to the star schema database, and configure the DSN on EPM System Configurator (11.1.1.3)
  UDL file is connected correctly, but when we try to 'Create star schema' we get an "Error occurred whil connection to the database" error.
  
  Any ideas? are we missing something?
  
  Concerning

  Have you given the grant of rights 'connect' to the database or schema?

  Varun

• Loss of quality when saving to a file of the CS6 to CS4 (IDML) to work on CS5?

  Employees of super good day!  I would like to know if there is loss of quality when recording in a file of the CS6 to CS4 (IDML) to work on CS5?

  The only loss should be all of the new features in the latest version that are not available in the older version not will be not paid.

• when insufficient privileges connect you to the database as sysdba

  I installed a vision with Oracle EBS R12 database. I need to connect to the database as sysdba to unlock the system account. but when I ran command sqlplus / as sysdba, I will this error "ORA-01031: insufficient privileges".
  I sought an answer in the internet, most answer said that it requires the user to linux to be in the dba group. in my config.c file I have this definiation "#define SS_DBA_GRP 'Oracle'. This group "Oracle" is my dba group. and I also checked my current user id (Oracle username is too) and the group, I got:
  [Oracle@linux admin] $id Oracle
  UID = 500 (Oracle) gid = 500 (Oracle) groups = 500 (Oracle)
  all above looks them good to me. I also added authentication_services to sqlnet.ora like this: sqlnet. authentication_services = (All). but I still have the same error. Can someone tell me what is the problem?
  Or y at - it another way to unlock the account system?
  
  Published by: user12100435 on April 15, 2013 19:53

  user12100435 wrote:
  I installed a vision with Oracle EBS R12 database. I need to connect to the database as sysdba to unlock the system account. but when I ran command sqlplus / as sysdba, I will this error "ORA-01031: insufficient privileges".
  I sought an answer in the internet, most answer said that it requires the user to linux to be in the dba group. in my config.c file I have this definiation "#define SS_DBA_GRP 'Oracle'. This group "Oracle" is my dba group. and I also checked my current user id (Oracle username is too) and the group, I got:
  [Oracle@linux admin] $id Oracle
  UID = 500 (Oracle) gid = 500 (Oracle) groups = 500 (Oracle)
  all above looks them good to me. I also added authentication_services to sqlnet.ora like this: sqlnet. authentication_services = (All). but I still have the same error. Can someone tell me what is the problem?
  Or y at - it another way to unlock the account system?

  Published by: user12100435 on April 15, 2013 19:53

  your operating system user must be member of the group 'dba' OS

• How to view the zero in the dashboard reports when there is no data in the database?

  I'm generation of trend analysis report
  
  in which I not show. so each month on a site web, I have all the data for a given month July (because there is no success during the previous month), report is generated with all months except JULY.
  
  Is their any way to view the zero with the name of the month when there is no data (unsuccessfully) in the database?
  
  ex.
  Jan 10
  20 February
  15 March
  Apr 4
  May 12
  June 16
  July 0 <---(display zero here)
  August 11
  9 sep
  .
  .
  Dec 8

  You owe us an outerjoin:

  http://obiee101.blogspot.com/search/label/outer%20JOIN

  concerning

  John
  http://obiee101.blogspot.com

• I get an error of 0x8007042c code when I try to turn on the Windows Firewall.

  Original title: firewall of windows 7 is not not useful

  can not turn on the windows firewall 7 on Dungeon receives an error of 0x8007042c

  I tried many other suggestions, without success. Help would be very appreciated

  See the Microsoft Knowledge Base article to resolve the error of 0x8007042c - http://support.microsoft.com/kb/2530126

  Jim

• 404 error page is displayed when you try to log in the site of catalyst for business to manage/delete site

  

  Hi Trikyfab,

  I checked and found that the domain arrowsofthethunderdragon.com does not point to the servers of BC:

  Screenshot by Lightshot

  You must update the nameservers at the domain registrar to that point the domain to BC that you can connect to the site via arrowsofthethunderdragon.com/admin

  Until the moment that the domain does not point to the servers of BC, you can connect to the site via the URL below system admin panel:

  arrows2.BusinessCatalyst.com/Admin/index.aspx

  Kind regards

  Radi amin

• Error 2738 could not access VBScript Runtime for custom during the installation of a turbostick action.

  I am trying to install a turbo stick on my acer aspire - and getting a 2738 error could not access VBScript Runtime for custom action. I am running windows 7 and acer and Bell - my provider have not been able to help.

  Kevin

  Hey Kevin,

  Thank you for the update.

  1. Run as administrator command prompt:
     1. Menu start-> all programs-> Accessories
     2. Right-click on command prompt and select run as administrator
  2. Type the following command at the prompt: reg delete "HKCU\SOFTWARE \Classes\CLSID\{B54F3741-5B07-11CF-A4B0-00AA004A55E8}" /f, then press on enter.
  3. Then, you must also type the following command: c:\windows\system32\regsvr32 vbscript.dll, and then press ENTER.

  Note: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

• Error: "WindowsUpdate_8007063" and "WindowsUpdate_dt000" when installing updates in Windows 7 machine.

  Original title: 80070663 error code appears when...

  This error code is displayed when I try to manually update the "WindowsUpdate_8007063" and "WindowsUpdate_dt000".  The automatic update has not once or twice each of these 8 days or more.

  you have problems with

  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  If you use Microsoft Office, you can run the Microsoft Fix it 50461 that corrects the problem. Look at the following KB:http://support.microsoft.com/kb/2258121>

• I get an error 0 x 80244019 when you try to update on express update

  This error keeps popping up when I try to update on the custom or express update error code is 0 x 80244019

  You cannot download updates when you access the Windows Update Web site from a Windows XP-based computer that is behind a firewall or a proxy server
  http://support.Microsoft.com/kb/896226

• E.M.P. 11.1.2.2 Config Error - EPMCFG-10368: unable to connect to the database.

  Hello
  
  I found the error when configuring EPM 11.1.2.2 below system
  
  Error message indicated as "EPMCFG-10368: unable to connect to the database." Check the database connection information'.
  
  Environment: Windows XP SP2, SQL Server 2005.
  
  Please help me solve the problem. Please also find the screen shot to http://ge.tt/6xqpj0L/v/0?c
  
  Kind regards
  Naveen
  
  Published by: Naveen on July 25, 2012 17:35

  Windows XP is not supported for client components not, I recommend that you install on an operating system that is supported so usually, when there is trouble connecting to SQL Server, it is down from TCP/IP not been activated, also correct for a static port, make sure that no firewalls are in place.

  See you soon

  John
  http://John-Goodwin.blogspot.com/

• the connection to the database: 404 error # _mmserverscript...

  When I try to connect to the database, I get this error:

  (1) there is no server running on the server test.

  2) the test specified for this site server is not mapped with the... _mmServerScripts/MMHTTPDB.php URL . Make sure that the URL prefix is the root of the site.

  Can someone help pleeeeease?
  

  Take a look at the 6th minute of the video on this page http://helpx.adobe.com/x-productkb/policy-pricing/dreamweaver-cc-serve r - extensions.html

• PC crashes when saving files on network

  When I try to save a copy of a file on my network drives, my PC hangs indefinitely until I end the process that is suspended.

  No one else on the network is affected by this symptom, and the PC has no problems to access the network or the Internet

  Hello
   
  1. were you able to save files previously without this problem?
  2. you remember changes recently?
   
  Follow the steps mentioned below and check if they help to solve your problem.
   
  Step 1: Check Event Viewer for detailed information on the problem. Consult the following links.
  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Event-Viewer
  
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-information-appears-in-event-logs-Event-Viewer
   
  Step 2: Try to save a file on the desktop and check if the computer crashes. Also open the Task Manager and try to end the process SearchIndexer.exe. This, as mentioned below.
   
  a. right-click on the taskbar and select Task Manager.
  b. click processes tab, and find SearchIndexer.exe.
  c. Select the message and click on end process.
   
  Step 3: Temporarily try to disable the antivirus on the computer program and check if the problem persists. If the problem does not occur, check if there are updates available for the safety program
   
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software  
   
  Note: Check that you activate your anti-virus protection on the computer back after you complete these steps. It is not recommended to disable these settings on the computer. It's just to solve the problem.
   
  Step 4: If this is not enough, put the computer to boot in order to check if the computer crashes when saving a file. If the problem does not occur in the clean boot state, then you can try the procedure in the following Knowledge Base Article and see the application or program is the cause.
   
  http://support.Microsoft.com/kb/929135
   
  Note: Make sure that you put the computer to a Normal startup, once the troubleshooting completed.
  
  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• Control of the database on Windows - gives error cannot find server or DNS error

  Hi all
  
  After the installation of 10g on Windows services necessary for my new db are running, earpiece is in place.
  
  But when I try to set up the database via http://pnclultraprd.corporate.mem.5500/em/console/logon/logon control
  I get "cannot display the page. Can not find the server.
  
  I did have this before on new facilities and I'm stuck.
  
  Any tips? Thank you, John

  I just noticed that you have un.5500 instead of: 5500 in your URL