Error 633: the modem (or other connecting device) is already in use or is not configured correctly. Any solution?

Similar Questions

• Problem: Error 633: the modem (or other connecting device) is already in use or is not configured correctly.

  While I am connected to internet using Reliance Netconnect Huawei 1260, the connection disconnects after 10 to 15 minutes. Shows as connected Netconnect but does not work. I try to disconnect the connection, but it gives an error.

  Reconnect to always remove the modem and then re - login again.

  Please provede me a permanent solution to this. I use Windows 7 Enterprise

  Hello

  1. If it works well before?

  2. what version of Modem drivers do you use? Do you have any other device connected to the computer?

  First of all, I suggest you to check if the modem is compatible with Windows 7.

  Check out the link:

  Windows 7 Compatibility Center:

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  I would also recommend to connect the modem to a different computer and check if it detects there. If it does not work on another computer also, then the problem is with the modem and I would ask you to contact the manufacturer of the modem for any further assistance.

  Error 633 indicates that the port is already in use or is not configured for remote access dial out. You may need to check if the VPN and the connection connection try to use the same port that is causing the problem. You may need to check the settings of the modem and change the port for your needs.

  To work around this problem, use one of the following methods:

  Method 1:

  Reserves explicitly the TCP port that is used for the VPN connection. To do this, follow these steps:

  a. click Start, click run, type regedit.exe in the Open box and then click OK.

  b. in the registry editor, find and then click the following registry subkey:

  HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Tcpip\Parameters

  (c) in the Edit menu, point tonewand then click multi-string value.

  d. rename the multi-string value as 'ReservedPorts' and then double-clickReservedPorts.

  e. in the value data box, type1723-1723, and then click OK.

  f. exit the registry editor.

  Registry warning: this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://support.microsoft.com/kb/322756/

  .

  Method 2:

  Use the netstat command to find the program that is using port 1723. Then, end the process for this program. To do this, follow these steps:

  a. click Start, click run, type cmd.exe in the Open box and then click OK.

  b. at the command prompt, type the following command and press ENTER:

  NETSTAT - aon

  c. in the result which appears, identify the process ID for the program, if any, who is using the TCP port 1723.

  d. at the command prompt, type the following command and press ENTER:taskkill/pid PID/f

  Note: The taskkill command terminates the process that corresponds to the ID of the process. The/F option is used forcefully to complete the process.

  e. at the command prompt, typeexitand press ENTER to quit the command prompt.

  Restart your computer. This may cause the program that uses the TCP 1723 port to use a different port.

  I hope that helps!

• The connection attempt failed because the modem (or other connecting device) on the remote computer is out of use. Error 777

  I've always used my blackberry to tether my phone but I get the following error message and I can't solve this problem, any help would be appreciated, thanks!

  The connection attempt failed because the modem (or other connecting device) on the remote computer is out of use. Error 777

  Hello

  It seems that the blackberry is not more.

  Pass the installation attaches on the blackberry and make sure that it is configured properly and work.

• Satellite A200: Modem has an error 633: already in use or is not configured properly

  My laptop is A200-FE0.

  When I tried to make a dial-up connection, there is a window of error says:
  "Error 633: the modem (or other connecting device) is already in use or is.
  not configured correctly.

  When I test my modem by clicking the modem of the request under the Diagnostics tab in the modems tool of the
  The modem control panel, normally responds and seem to work
  correctly.

  When I test my modem using Toshiba diagnostic tools, it displays "pass" and I canhear the tone Dáil too.

  I tired to edition and reinstall the driver twice.
  But I can't make a dial-up connection and get error 633. I'm really upset about it.

  Please help me! Thank you very much!

  Check this thread:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?threadID=27402

• Error modem already in use or is not configured properly

  Original title: try to use the modem internet cleartalk on laptop

  Downloaded there screen says.  but when I try to connect it gives me an error that it is already in use or is not configured correctly. It is of ClearTalk EVDO Mobile Broadband

  Hello

  1. If it works well before?

  2. what version of Modem drivers do you use?

  3. What is the model number of your computer modem?

  4. do you have other devices connected to the computer?

  The error you receive is typical of drivers who don't are incorrect or not installed. You run the system with UAC turned?

  I recommend you to connect the modem to another computer that is running Windows Vista and check if it detects there. If it does not work on another computer also, then the problem is with the modem and I would ask you to contact the manufacturer of the modem for any further assistance.

  You can also try the following methods and check if it helps.

  Method 1:
  To resolve this problem, remove the modem, and then restart the computer. When the computer restarts, Windows detects the modem and attempts to install the driver appropriate for that. To do this, follow these steps:
  a. log in the computer as an administrator or as a member of the Administrators group.
  b. click Start and then click Control Panel.
  c. double-click phone and Modem Options.
  d. click the Modems tab.
  e. in the following modems are installed list, click the modem that you want to delete and then click Delete .
  f. click Yes in response to the ""are you sure you want to remove the modem selected from your system? " " message.
  g. restart the computer.
  h. the found new hardware wizard starts. Follow the instructions in the wizard to reinstall the modem.

  Method 2:
  You can re-install the modem driver on the manufacturer's Web site and check.
  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Reference:--

  Solve the problems associated with the modem:

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-modem-problems

• SP A10 - Error 633: the modem is not installed or configured for Dial-Up

  I've already reformatted the hard drive and the utility CD to reinstall the modem driver. Anyone got tips on how to solve the problem? An external modem would solve it?
  Either way, it's a satellite pro A10

  Hello

  If the HARD drive is formatted, use the recovery CD and reinstall the OS. After that, the modem must be recognized and properly installed. After that, configure Dial connection and check the modem. If the modem is not defective, it should work.

  The strange thing is that there is Error 633 which means: the port is already in use or is not configured for remote access remote calls.
  Please check this interesting site http://www.modemsite.com/56k/duns633.asp.
  If there is no success please write again.

  Good bye

• All programs of the cloud creative suite adobe when they open are locked and do not respond. Any solution?

  All programs of the cloud creative suite adobe when they open are locked and do not respond. Any solution? I already tried to uninstall and reinstall everything but does not work. Mac OSX Yosemite 10.10.5

  Hello

  Please see: -.

  Errors ' Exit Code: 6, "" Exit Code: 7 "|"» CC, CS6, CS5.5

  Hope this helps!

• Error 633: The Modem already in use or not configured properly

  Hello

  I use a Windows7 Home Premium 64 bit PC.
  When I am trying to connect to the internet via 3 g USB modem, I get error 633: Modem is in use or not properly configured.
  The software and drivers have been installed correctly.  I uninstalled and re installed several times without success. I tried the same thing in safe mode without success.

  Any help is appreciated.
  Thank you

  Hello

  I suggest you to check if the modem is compatible with Windows 7.

  Check out the link:

  Windows 7 Compatibility Center:

  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/default.aspx

  I would also recommend to connect the modem to a different computer and check if it detects there. If it does not work on another computer also, then the problem is with the modem and I would ask you to contact the manufacturer of the modem for any further assistance.

• Problem of password of account, without that we can connect to the network on this computer. The error indicates, "the trust relationship between this device and the network is no longer valid.

  Hi, I hope you can help with this problem. A friend has 6 computers networked to a Tower Server and have a problem. A worker student put computers into hibernation, and since then, nobody can connect to the network on this computer. The error indicates, "the trust relationship between this device and the network is no longer valid. I tried to get into the pc to try removing network and replace it, but I can't get on the Administrators account because it has been disabled. I'm at a loss on how to proceed. My friend cannot afford a service call, so I'll try to help him.  Thank you

  If the computer is on a domain then there are at least two accounts that can be used to remove the computer from the domain:

  • A domain administrator account.
  • A local administrator account.

  When your friend has launched Windows for the first time after buying the machine, he was prompted to enter the name of an account. This account is created automatically with administrator privileges. He should use it now.

• I get the following error when I am trying to connect to a network by using different credentials. 1219 system error has occurred.

  Multiple connections to a server or resource shared by the same user

  I get the following error when I am trying to connect to a network by using different credentials.

  1219 system error has occurred.

  Multiple connections to a server or a shared resource by the same user, using more than one user name, are not allowed. Disconnect all previous connections to the server or shared resource and try again...

  I don't want to use the IP address. and I don't want to delete all connections using the net use * / delete command.

  Kindly give me the solution as I am now frustrated with this issue.

  Kind regards

  Sajid

  Hello

  ·         Have you tried to access the files that were on Skydrive?

  ·         Did someone else uses your computer?

  From now on, I suggest you try the steps mentioned in the article below.

  Error message when you use user credentials to connect to a network from a Windows computer: "the specified network folder is currently mapped using a different username and password.

  http://support.Microsoft.com/kb/938120

  You can also ask your question in the forum of the Tech Net Windows Server using best.

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer

  Hope this information is helpful and let me know if you need additional assistance.

• Your device is not configured correctly(code 1) error

  Hello

  I have windows XP currently installed on my computer and I also have the new hard drive (seagate 500 gb) installed on my computer.
  I am facing the error with my cell phone (samsung galaxy s duos GT s7562) with my computer and I am unable to make any transfer of media through the PSG.
  Under portable devices > PSG > properties, I get the following message. > "this device is not configured correctly. (Code 1)
  To reinstall the drivers for this device, click on reinstall. When I try update driver it shows "your device is not configured correctly (code 1 error). I tried gel and reinstall driver MTP via "scan for hardware changes", but it does not yet solve my problem.
  How can I get my samsung android smart phone connected to my pc and start sharing media through the PSG. problem certainly lies in the pc.
  Help me out.i am going nuts about that...
  Pankaj.

  Hey,.

  have you found this KB link?

  See "Code 1" from the link

  Explanation of error codes generated by Device Manager in Windows XP Professional

  http://support.Microsoft.com/kb/310123/en-us

• Check no error in the app store so I don't know that my apple id pass is correct

  Check no error in the app store so I don't know that my apple ID pass is correct

  Go here > https://www.apple.com/emea/support/itunes/contact.html < and fill out the form

• No links to the local area network connection. But how to use the Internet again, please help establish a LAN connection.

  Original title: no local network connection

  No links to the local area network connection. But how to use the Internet again, please help establish a LAN connection.

  Hi H.mustafaakyurek,

  ·         What operating system is installed on your computer?

  You can view the following items on the creation of a network connection:

  Setting up a network home

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-home-network

   

  Start here to set up a home network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/start-here-to-set-up-a-home-network-in-Windows-7

   

  Setting up a wireless network

  http://Windows.Microsoft.com/en-us/Windows7/setting-up-a-wireless-network

  Also see the following articles on the connection of an Internet connection:

  What do I need to connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/what-do-I-need-to-connect-to-the-Internet

   

  Allows to connect to the Internet mobile broadband

  http://Windows.Microsoft.com/en-us/Windows7/use-mobile-broadband-to-connect-to-the-Internet

  Hope this information helps.

• updated configuration failure Vista - updates not configured correctly. returning from the changes - code Error 80070020

  Updates installation but to the message indicating a configuration step 2 bed 'updates not configured correctly. reverting changes"error code is 80070020.

  http://support.Microsoft.com/kb/883825>

  08/10 / 1106:12:26

• Error 1335 the data4.cab file is corrupt and cannot be used, what I have to do

  Error 1335 the data4.cab file is corrupt and cannot be used, what I have to do

  Hi Max210662,

  Please follow the mentioned kb: http://helpx.adobe.com/creative-suite/kb/install-error-1311-1335-or.html .

  Kind regards

  Romit Sinha