Error executing the call of duty 2 (entry point not found) how to fix?

Similar Questions

• NtrigApplet - unable to connect to the driver: failed to open device___TVAgent.exe - Entry Point not found the procedure entry point PowerReadACValue could not be found in the dynamic library POWRPROF.dll

  Hi all

  I have a HP TouchSmart tx2-1025dx Notebook PC Vista... I met 2 large pop-up windows that will not close & appear as soon as I turn on my computer gives me a time DIFFICULT to access anything whatsoever...

  They read as follows:

  NtrigApplet - unable to connect to the driver: failure to open the device

  TVAgent.exe - Entry Point not found the procedure point PowerReadACValue entry is not found in the dynamic library POWRPROF.dll

  CAN SOMEONE PLEASE HELP?
  THANK U :)

  Hi the apprentice 85,

  Remember to make changes to the computer before that happened?

  Looks like the problem is hardware or software related, I suggest you follow the below mentioned steps below to refine the question

  Step 1: Disconnect all external devices (printers, scanner, USB (universal serial bus) readers, etc...)  Except the keyboard and mouse and then start.

  If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue.  Then get any drivers\software update for the device.

   

  Step 2: Put the computer to boot to determine which program is causing the problem

  Follow step 1 in the link below,

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem.

  Continue with the remaining steps to pin-point on the third party service.

  After find you the program that is causing the problem, you will have to perhaps to update or install a newer version of the program, if you rarely use that you should consider uninstalling the software.

  Important: n ' forget not the computer to start normal follow step 7 in the link.

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• dthtml.exe - Entry Point not found

  My 32 bit Vista installation has begun displaying the error message at startup:

  dthtml.exe - Entry Point not found

  "The entry procedure point not found _iob_func in the dynamic library MSVCR70.dll.

  I would be very grateful if someone knowledgeable could advise me on how to deal with this issue.

  Thank you very much

  johndoc37

  Hi johndoc37,

  I will need some additional information to help you best.

  ؠ exactly when you get this error message?

  ؠ all changes made on your computer recently?

  In the meantime, follow the instructions below that may help you resolve the issue.

  Method 1:

  To perform the clean boot procedure, follow the instructions in the link below.

  Step 1: Perform a clean boot

  Step 2: Enable half the services

  Step 3: Determine whether the problem returns

  Step 4: Enable half of the startup items
  Step 5: Determine whether the problem returns

  Step 6: Resolve the problem

  Step 7: Reset the computer to start as usual

  How to troubleshoot a problem by performing a clean boot in Windows Vista

  http://support.Microsoft.com/kb/929135

  After checking the problem, turn the computer back to the Normal mode.

  Uninstall or update the program that is causing the problem.

  Method 2:

  This problem is possibly due to Virus infection.

  Perform a virus online scan that might help you resolve the issue.

  Windows Live OneCare safety scanner is a free service designed to help ensure the health of your PC.

  • Check and remove viruses
  • Get rid of junk on your hard disk
  • Improve the performance of your PC

  Click on the link below for Online Virus scanner.

  http://safety.live.com/

  Check whether the problem is resolved.

  You can go to Microsoft Security Essentials protect your computer from malware.

  Click on the link below for more information on Microsoft Security Essentials.

  http://www.Microsoft.com/security_essentials/

  Please post back and let us know if it helped to solve your problem.

  Kind regards

  KarthiK TP

• I received a message after you have signed in: ST Services.exe - Entry Point not found.

  The context of xmlxpathfree proceduce entry point not found in the dynamic link library Libxml2.dll.  After canceling the message, another message came: MSWindows - ST Service Scheduling has stopped working?  What that is this allusion and what can I do about it?

  This program is associated with Dell Datasafe and possibly other Dell programs pre-installed on their computer. If you don't use a Dell Datasafe, you can try to uninstall it.

  There is a some evidence that this problem is caused by some registry cleaners and cleaning utilities.

• 'Lightroom, exe Entry Point not found' (in German)

  Hello

  I have the following problem, I tried to open Lightroom CC (and PS CC too) and I received the following message
  
  'Lightroom, exe Entry Point not found' (in German), PS und LR CC CC too.

  and 'crtCreateSymbolicLink' not found in the DLL "C: Windows\System32\MSVCP110.dll"
  any suggestions?
  Both have worked 10 days.  its all over now.

  Thanks a lot all-Ingolf

  Try reinstalling the library: http://www.microsoft.com/en-au/download/confirmation.aspx?id=30679

• hpqtra08.exe - Entry Point not found error. The Get procedure entry point Module F < [not found in KERNEL32.dll dynamic link library.

  Original title: hpqtra08.exe - Entry Point not found.  The Get procedure entry point Module F<[ could="" not="" be="" located="" in="" the="" dynamic="" link="" library="">

  hpqtra08.exe - Entry Point not found.  The Get procedure entry point Module F<[ could="" not="" be="" located="" in="" the="" dynamic="" link="" library="">

  (This keeps popping up on my screen and I don't know how to get rid of it. Can you please tell me what to do?)

  Hello

  ·         When exactly do you get this error message?

  ·         Did you of recent changes to the computer before this problem?

  ·         You are able to boot to the desktop?

  You can follow these suggestions:

  Method 1:

  If the previous step fails, follow these steps:

  a. restart the computer in safe mode and disable the HP service and check if the problem occurs. Follow the steps described in the following steps:

  b. restart your computer and start pressing F8 on your keyboard. On a computer that is configured to start to multiple operating systems, you can press the F8 key when the Boot Menu appears.

  c. Select an option when the Windows Advanced Options menu appears, and press ENTER.

  d. Click Start and run, type msconfig, and then click OK.

  e. the system dialog Configuration utility appears.

  f. click on the Services tab.

  g. Click to select the check box Services HP Digital Imaging Monitor or hpqtra08.exe.

  h. click OK.

  i. When you are prompted, click on restart to restart the computer.

  j. after reboot check if the problem occurs.

  Method 2:

  If the C:\Program Files, download and run the Microsoft of the link Security Scanner to make sure that your computer is not infected with the virus:

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: the Microsoft Safety Scanner expires 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.

• Get FL.exe - Entry Point not found 'point of entry procedure for NtAlpcSendWaitReceivePort not found in the dynamic link library ntdll.dll' error at boot fruity loops.

  Original title: ntdll.dll error at boot fruity loops.

  get FL.exe - Entry Point not found 'point of entry procedure for NtAlpcSendWaitReceivePort not found in the dynamic link library ntdll.dll' error when I try to start fruity loops after installing Kies from samsung for the new phone. How can I fix this error? Help, please. Thanks in advance! :)

  Hello
  I suggest you contact support FL. I couldn't find all of the resources for this program.
  Eddie B.

• .exe error] is not found the procedure entry point AddAtomW Entry Point not found in dynamic bindings KERNEL32 library. DLL when I try to run any program. I have

  Original title: [ProgramName] .exe Entry Point not found

  I get this message: the point procedure entry AddAtomW could not be found in dynamic bindings KERNEL32 library. DLL when I try to run any program. I don't know what to do. Help please!

  Hello

  1. did you of recent changes on the computer?

  Method 1:
   
  It is possible that some third-party programs installed on the computer is causing the problem.
  I suggest that you put the computer in a clean boot state and check if it helps.
  To help resolve the error and other messages, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.
   
  See the link below to learn more about how to clean boot.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353
   
  Reset the computer to start as usual
  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
  (a) click Start, type msconfig in the search box and press ENTER.
  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.
  (c) under the general tab, click the Normal startup option, and then click OK.
  (d) when you are prompted to restart the computer, click on restart.

  Method 2:

  Put your boot system helps determine if third-party applications or startup items are causing the problem. If so, you need to maybe contact the manufacturer of the program for updates or uninstall and reinstall the program.

  See the following article in the Microsoft KB for more information on how to solve a problem by performing a clean boot in Windows Vista or Windows 7:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/kb/929135

  Note: after a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

• Satellite P300: Error BSOD STOP: c0000139 {entry point not found}

  I had this error a few weeks on my Toshiba P300.
  When I start my laptop it appears a blue screen with an error for a fraction of a second:

  STOP: c0000139 {entry point not found}
  The procedure entry point ntoskrnl. ExiAcquireFastMutex is not found in the library of dynamic links Hal.dll.

  Then normal startup of Windows Vista.
  I get this error when I start the computer from the Hibernate mode. What does this error mean?

  I also have problems with my built-in webcam. I get the message: "locked by another application." I already reinstalled the software I downloaded from the site, but that did not help. The error has something to do with the webcam this doenst work properly?

  I put t know what can be the problem, but you must use restore system and OS rollback to an earlier time before this error message.

  Subject of webcam, please visit http://forums.computers.toshiba-europe.com/forums/thread.jspa?messageID=131308

• the apsGetReady entry point not found in the library of links dynamic wlanapi.dll

  What is apsGetReady?     Do I need?   If yes how can I do?  If this is not the case, how can I remove the window error message.

  """""""""""""""""""""""""""""""""""""""""""'''

  Wzcsldr2.exe found entry point

  the apsGetReady entry point not found in the library of links dynamic wlanapi.dll

  """"""""""""""""""""""""""""""""""""""""""""""""

  Hello

  1. When you receive this error message?
  2. you did it before the issue of any material changes or software?
  3. what service pack and antivirus are installed on your system?
  4. What is the brand and model of the router you are using to connect to the Internet/network

  5 are you facing problems to connect to the Internet or to the network?

  6. are you using any third-party wireless / network in the System Manager software?

  Method 1:
  

  Step 1: Boot your system in 'Safe Mode with networking' and check if you get the same error message. Then review the article mentioned below to do so:
  A description of the start in Windows XP Mode options:
  http://support.Microsoft.com/kb/315222

  Step 2: If you receive any error in safe mode, please boot your system to the boot and see if the problem still occurs in this mode. Try now to the KB article to perform the clean boot:
  http://support.Microsoft.com/kb/310353
  Important: After you use the clean boot in order to solve your problem follow the steps in the "steps to configure Windows to use a Normal startup state" section to start your system in normal mode.

  Method 2: Please see Using D-Link, if you use D link router.
  http://www.Dlink.com/support/default.aspx

• Cannot open iTunes or other things. iTunes.exe - Entry Point not found error

  Original title: iTunes.exe - Entry Point not found

  iTunes.exe - Entry Point not found

  The procedure entry point
  AVCFPlayerAppliesMediaSelectionCriteriaAutomaticallyKey is not found in the AVFoundationCF.dll dynamic link library.

  I don't understand why that keeps popping up whenever I'm going to try and open iTunes. Then he told me that iTunes is not installed correctly, even after you uninstall it and install and it installed successfully. It is really starting to make me angry. I don't know what I did. I was working with my iPod Classic moms and it simply does not work so I tried hard so he can. I think I could have managed to get rid of something by accident. Can someone please help please?
   
   
  Discussions were merged.
  Deleted duplicate.
   

  Hello

  Uninstall everything according to the instructions from Apple:

  «Remove and reinstall iTunes, QuickTime, and other software components for Windows Vista or Windows 7»

  http://support.Apple.com/kb/HT1923

  It is also the same list of what to remove what is in the link above from Apple:

  http://pcsupport.about.com/od/findbyerrormessage/a/MSVCR80-DLL-not-found-missing-error.htm

  Or try this program to remove it:

  http://www.revouninstaller.com/revo_uninstaller_free_download.html

  Then, download and save the iTunes on the desktop > then right click > select run as administrator to install.

  If the advice already given does not, please contact Apple for assistance.

  "Not to install iTunes or QuickTime for Windows"

  http://support.Apple.com/kb/HT1926

  "iTunes support-how to use iTunes.

  http://www.Apple.com/support/iTunes/

  "Contact iTunes Support.

  http://www.Apple.com/support/iTunes/contact/

  Or ask in the community Apple iTunes:

  https://discussions.Apple.com/community/iTunes

  See you soon.

• 32-bit installation issues - Vista Entry Point not found error

  I'm doing a clean install of Windows Vista 32 Bit in Windows 2000 (Service Pack 4). When the installation asks you which drive I would install windows for, as I have Sata drives running of a Sata/RAID controller card he asked pilots. Any version of this driver, I offer for this installation fails with the following error "Windows Installer: setup.exe - Entry Point not found - the procedure entry point LZClose could not be found in KERNEL32.dll dynamic link library ' I have a Silicon Image Sil 3513 SATALink PCI controller that manages my hard drives. The same drivers worked well to install Windows 2000. As I upgrade to Vista version I can only run through the windows so I could not try and see if it will install directly from DOS.

  Thank you

  James

  Found a solution. I use the Windows Vista upgrade version & thus tried to install through Windows 2000. However Win 2 k interfaces drives in a different mode of Vista, while he was in conflict. I solved the problem by installing Vista via the bootable disc.

  Now just to find the compatible drivers for my asus motherboard and aircraft... Grrrr I'm sure I got this Vista computer previously without all these headaches...

• -Pop-up message error when I start my computer: "TVAgent.exe - Entry Point not found".

  When I start my computer, the first message when I see my desktop is a pop up that says "TVAgent.exe - entry not found.» The procedure entry point not found PowerReadACValues in the dynamic library POWRPROF.dll. "I try to close it and it appears in the same as spot 10 times and then finally I can close it and it will not reappear. I tried a full sweep of the computer with Norton and it did not come with anything. All my programs and all seem to work fine right after, but I fear that there is something wrong. I am running Windows Vista.

  Hi Csiew42,

  Thank you for visiting Microsoft Answers.

  ·         Which version of Windows Vista is installed on your computer?
  ·         Remember to make changes to the computer recently?
  ·         Who is the manufacturer of your computer?

  I suggest to perform the clean boot and check if you get the error again. Clean boot will start Windows Vista by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  The following link has steps showing how to perform the clean boot: http://support.microsoft.com/kb/929135

  (1) perform the clean boot (check the link to perform the clean boot).

  (2) enable half the services.

  (3) determine if the problem comes back.

  (4) enable half of the startup items.

  (5) determine if the problem comes back.

  (6) repeat the steps above until you discover which program or service is causing the problem.

  After you determine the startup item or the service that is causing the problem, contact the manufacturer of the program to determine if the problem can be solved. Or, run the System Configuration utility, and then click to clear the check box of the element of the problem.

  Note: Please make sure that the computer is configured to start as usual according to step 7 of the article: how to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7: http://support.microsoft.com/kb/929135

  Hope the helps of information. Please post back and we do know.

  Kind regards
  Joel S

• Need help with LogonUI.exe - entry point not found error

  Apparently my IT cannot resolve this error. Reason of the Department was that, sometimes, the password cannot be captured.

  The following error came up:

  LogonUI.exe - not found entry point

  the procedure entry point IsAdditionalKeyFileAvailableFromKernel could not be located in the dynamic link library sdd.dll

  Is there a way to fix this?

  Hello

  In addition to the steps provided by Deepak K prajapati, you can also see this link: Entry Point not found for more option.

  Let us know if you need help.

  Kind regards

  Tiero Chi

• Windows 7 - "Entry Point not found" error when trying to play a game

  createAccessible@wxWindowBase@@UAEPAVwxAccessible@@XZ DMC 5 could not be located in the dynamic link library wxmsw28u_core_vc_custom.dll.

  Separated from -.

  https://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-gaming/Windows-7-entry-point-not-found-error-while/3c19d3f0-7667-4989-8bc2-ae807d9ea568

  Hi Patricia,

  Please contact the Microsoft Community.

  Which game you try to play?

  I would have you try and re-install the game and check.

  In addition, I'd like to as you open the prompt in elevated mode and then try and register the DLL by using this command:

  Regsvr32 write the name of the DLL file.

  We know if that helps you.