Error FPGA: DiagramReset did not clear within the period

Similar Questions

• Error-61207 and DiagramReset did not clear in the expiration time.

  Hello

  Just to start with FPGA programming and trying to get my NOR-9155 and NOR-9223 to capture some simple analog voltages.

  After you have compiled the NI9223 get started (FPGA) for my 9155 - NEITHER with NOR-9223 VI I get the following error messages:

  LabVIEW FPGA: Internal error: DiagramReset is not clear in time.
  Please contact National Instruments Technical Support on ni.com/support.
  Error-61207 occurred at niLvFpga_Open_NI 9155.vi

  I tried to reboot the host and the chassis and reset FPGA but continue to receive this error message.
  I am running LabVIEW 2012 SP1 on a Dell Inspiron 1520 (Intel Celeron 540 @ 1.86GHz. and 3574 MB of RAM and Windows Vista Home Basic

  I ran it on another laptop computer (Dell Dimension M6700) and do not receive this error, and the project works very well.

  Any help would be appreciated.

  Bob

  Soloman,

  I met Adam Bakehouse (rep FOR Imperial College London) Thursday and he suggested that my view of the installation of Windows XP instead of Windows Vista. I did it and everything seems to work fine now. I realize that XP is no longer supported bu MIcrosoft, but this correction will enable me to move forward in the short term, using my old laptop computer Dell.

  Thanks a lot for your help.

  Kind regards

  Bob

• I am running Windows 7 and noticed that Windows updates did not work. The parameters are defined for the update every day. When I went to update manually returned an error WindowsUpdate_80070017. MSFT site was no help. Any recommendations?

  I am running Windows 7 and noticed that Windows updates did not work. The parameters are defined for the update every day. When I went to update manually returned an error WindowsUpdate_80070017.  MSFT site was no help. Any recommendations?

  Since neither updates Jan - 10 have installed, I'm going to hand you Support MS in the hope that they can resolve the problem. See below.

  That being said, is an interpretation of the 80070017 - cyclic redundancy check error "a device attached to the system does not work," which suggests that a hardware problem might be the cause of the error (although I must say that it is a very low possibility in this case).

  Good luck!

  =======================

  Visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy. If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Please help, my other computer shows an error message: "Windows did not start because of an error in the software: load needed DLLs for kernel.

  Please help, my other computer shows an error message: "Windows did not start because of an error in the software: load needed DLLs for kernel.

  Hello

  ·          What is the number and the model of the computer?

  ·          What is the service pack installed?

  ·          The meadow of operating system has been installed on the computer?

  ·          Do you remember any changes made on the computer before the show?

  Try the steps listed in the link below: how to fix a computer that does not start: http://www.microsoft.com/windowsxp/using/setup/support/nostart.mspx

  You can also check: Error Message: Windows could not start because of the mistake in... : http://support.microsoft.com/kb/326671

• Windows service error: "error 1053: the service did not respond at the beginning or".

  Hello

  I had created a Windows service to start and stop a Tomcat server. Whenever the Tomcat server works with Multi threaded items and if I try to stop the Tomcat using the Windows service I get the following error, "error 1053: the service did not respond at the beginning or".
  application for review in due course. "

  I can't change the value of 'WaitToKillServiceTimeout' as my services are running on the client computer. Y at - it any other way I can do windows services to expect my Application Server series of all threads and stops.

  Kind regards

  Amina

  Hello

  I suggest you to ask your question in the Microsoft TechNet Forums: http://social.technet.microsoft.com/Forums/nl/category/windowsserver

  I hope this helps.

• Bridge 5.0.2.4 with camera RAW 8.4.0.199 ON a MAC 10.10.1. Try to update camera RAW 8.7 to get my canon 7dMK2 raw files to work. But the update I have the last update! Witch, I did not clearly. And my Photoshop have different camera RAW

  Bridge 5.0.2.4 with camera RAW 8.4.0.199 ON a MAC 10.10.1. Try to update camera RAW 8.7 to get my canon 7dMK2 raw files to work. But the update I have the last update! Witch, I did not clearly. And my Photoshop have different camera RAW plug-in. 8.4 the old and the new 8.7. But it does not work. Have removed and reinstalled several times. What is going on? Why can't update bridge to the last version 8.7 or read my raw files from the Canon 7dmk2?

  Try this:

  http://blogs.Adobe.com/Crawlspace/2011/03/keeping-Photoshop-up-to-date.html#NotConnected

• Error iTunes - iTunes could not connect to the store purchases - if you have any firewall software, make sure it has been set to allow communication on port 443.

  My itunes has been fine. All of a sudden today it now gives me this error: error Itunes - iTunes could not connect to the store purchases - if you have a software firewall, make sure that it has been set to allow communication on port 443.

  I do not have my firewall active. I connected to itunes, quit itunes, reconnected - still a problem.

  Was there an update and now it's a bug? Help!

  Thank you!

  Run the Console application in one of the following ways:

  ☞ Enter the first letters of his name in a Spotlight search. Select from the results (it should be at the top).

  ☞ In the Finder, select go utilities ▹ of menu bar or press the combination of keys shift-command-U. The application is in the folder that opens.

  ☞ Open LaunchPad and start typing the name.

  The title of the Console window should be all Messages. If it isn't, select

  SYSTEM LOG QUERIES ▹ all Messages

  in the list of logs on the left. If you don't see this list, select

  List of newspapers seen ▹ display

  in the menu at the top of the screen bar.

  Click on the clear view icon in the toolbar. Then take an action that does not work the way you expect. Select all of the lines that appear in the Console window. Copy to the Clipboard by pressing Control-C key combination. Paste into a reply to this message by pressing command + V.

  The journal contains a large amount of information, almost everything that is not relevant to solve a particular problem. When you post a journal excerpt, be selective. A few dozen lines are almost always more than enough.

  Please don't dump blindly thousands of lines in the journal in this discussion.

  Please do not post screenshots of log messages - text poster.

  Some private information, such as your name or e-mail address, can appear in the log. Anonymize before posting.

  When you post the journal excerpt, an error message may appear on the web page: "you include content in your post that is not allowed", or "the message contains invalid characters." It's a bug in the forum software. Thanks for posting the text on Pastebin, then post here a link to the page you created.

  If you have an account on Pastebin, please do not select private in exposure menu to paste on the page, because no one else that you will be able to see it.

• Windows xp hp will not start. error message: Windows has not start because the following file is missing or corrupt: < root windows > \system32\hal.dll. Please re - install a copy of the above file.

  Hello, I recently restored my windows hp tower to its factory because of virus settings and when I restarted my PC I recieced this error message: Windows has not start because the following file is missing or corrupt: \system32\hal.dll Please reinstall a copy of the above file.  where can I get a copy? and is it possible to download the start software and burn it to a cd?

  Hi FRANKGRIMES_945,

  What is the model of your computer?

  (a) you can try to arrange for a Windows XP disk that corresponds to the same edition, as it is installed on your machine.

  (b) thereafter, follow this link & check if you are able to start correctly on the desktop.

  Error message: "Windows did not start because of a configuration of the disk of the computer problem.

  Hope the helps of information.
  Please post back and we do know.

• Error message: Windows has not start because the following file is missing or damaged

  This error sometimes occurs when starting upwards from my Win XP computer:
  Windows could not start because the following file is missing or damaged. Windows root\system32\hal.dll. Please reinstall a copy of the above file.
  the computer then complete the beginning upward and operate normally.

  How can I stop this error message?

  Kind regards

  Hello

  ·         Since when are you facing this problem?

  ·         Remember to make changes to the system?

   

  I suggest to disable the startup items when the system starts up and then check if the problem is resolved.

  How to disable programs that run when you start Windows XP Home Edition or Windows Vista

  http://support.Microsoft.com/kb/270035

  I suggest following the steps mentioned in the article below and check if

  Error message: "Windows did not start because of a configuration of the disk of the computer problem.

  http://support.Microsoft.com/kb/314477

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.

• SE error message: Windows has not start because the following file is missing or damaged. Windows root\system32\hal.dll, after removing the RAM

  Original title: computer \sysytems32|hal.dll shows this when starting. Old dimension 2350.

  I tried to install McAfee Total Protection on an old Dimension 2350 and after that computer system has been slow and useless. After the call of Mcafee, they told me my RAM was too small at 640 MB and said if necessary to upgrade to 1 GB. I called Dell and they wanted to know that the RAM so had to remove it. After removal and reinstallation of the computer, but I got the error above.

  I have the reinstallation windows xp cd drive professional service pack 3, but can not get beryond this message options

  Hi gfritz1,

  You can consult the following Microsoft KB article and check if it helps:

  Error message: "Windows did not start because of a configuration of the disk of the computer problem.

  http://support.Microsoft.com/kb/314477

  Hope this information is useful.

  Jeremy K
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• 4 usb ports - this device is disabled because the firmware of the device did not give him the necessary resources. (Code 29)

  m facing a problem with hub 4 ports usb of my... When I connect usb hub my with my usb keyboard and mouse, and then the lights of the suite to get devices but they doesnot work... and the error message shows... I checked in Device Manager and I got the message details which are given below.

  Device status:

  This device is disabled because the firmware of the device did not give him the necessary resources. (Code 29)

  driver version:

  6.1.7601.17514

  Please help me... Thank you.

  Hello

  In the Device Manager - right click on the device and Uninstall - when complete reboot.

  Check in the Device Manager to see if the device re-installed. If it isn't action - Scan for
  hardware changes.

  Also check the BIOS - Setup/settings - often F2 for system start - make sure that the USB port
  is activated. Check with Support from the manufacturer of the system/motherboard, their documentation online.
  and ask in their forums.

  How to fix error Code 29
  http://pcsupport.about.com/od/errorc/a/code-29-error.htm

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• I downloaded Adobe Creative Cloud and asked After Effect.  They received my payment, but did not send me the activation code.  Where can I find it?

  I downloaded Adobe Creative Cloud and asked After Effect.  They received my payment, but did not send me the activation code.  Where can I find it?

  Hi Dawud,

  You can follow the article: sign activation, or connection errors. CS5.5 and later, Acrobat DC that will help you get this issue fixed.

  Let us know for any additional questions.

  Thank you

  Yann Arora

• My office has been reset to the factory settings. I am enrolled in my sync account, but my favorites that are on my laptop, did not came to the top. Now what?

  I was fortunately sync-ed a year betweem my computer laptop Mac iBook and desktop HP - a lot of bookmarks - I am a student. My office had a small problem and I got it clean and reset to the factory settings. I'm now creating upward. I installed Firefox and made Google my default search engine. Then I logged in sync - no problem (even email, password... I wrote it!) I clicked sync, but my favorites are not come to the top. I closed Firefox and re-opened, but still no bookmarks. I looked at the settings and everything is checked. I wouldn't change anything. What Miss me? Thank you.

  Both devices use new synchronization and more importantly on Firefox 30.

  If you you don't need the synchronization of the former, and even if you use the same address as used for synchronization of the old all should operate under the new synchronization.

  I think that the new synchronization drops devices that have not synchronized within the past 21 days.

  Former site of Firefox Sync: new Firefox Sync https://account.services.mozilla.com/ site: https://accounts.firefox.com

• I read the excellent instructions, but cannot locate the green arrow to start the download! I did not accidentally remove the arrow, because he was never

  I went on the Mozilla site to download to my Mac. I read the excellent instructions, but cannot locate the green arrow to start the download! I did not remove accidentally the arrow, as it was never there to be seen. I use Safari and don't have Firefox on my MAC (to my knowledge).

  Thank you

  PS: I clicked on the 'automatically add' and downloaded the file, but when I tried to open it, I get the message "Safari cannot read this file. Cool, huh?

  See how to install Firefox on Mac.

  • https://support.Mozilla.org/KB/installing+Firefox+on+Mac
  • http://KB.mozillazine.org/Installing_Firefox#Mac_os_x

  Open the Firefox disk image file and drag the Firefox program into the Applications folder on your hard drive.
  Do not double-click the Firefox to run from the disk image, but instead, drag it out of the DMG file.

• How can I configure xbox 360 on windows XP, all instructions are for Media Center which I did not and asks the key code.

  Windows XP and using the Xbox 360!

  How can I configure xbox 360 on windows XP, all instructions are for Media Center which I did not and asks the key code.  I don't have media player. I received a key to the xbox code, BUT Media Player do not ask for it? My wireless works fine.  XBox works very well. Yes, I know that I should upgrade to Windows 7 but until my budget allows, is what I have.  Thank you.

  Try this link for XBox: http://social.msdn.microsoft.com/Search/en-US?query=XBOX%20on%20Windows%20XP&ac=3