Error: Hex 0xBFF60492

Similar Questions

• Error when access instrument ' primary error: (Hex 0xBFFA003D) could not find any channel or repeated capacity channels.

  Hi all

  I believe that I have correctly configured max I'm trying to use the PXI-6229 device via. When I try initialized, I get the following error:

  The primary error: (Hex 0xBFFA003D) could not find any channel or repeated capacity channels.

  Clues about what means error?

  Thank you

  Manesh

  First of all, you'll have more help in the appropriate forum.  This seems to be a problem DAQmx and their forum is here: http://forums.ni.com/t5/Multifunction-DAQ/bd-p/250

  Secondly is this help: http://forums.ni.com/t5/Switch-Hardware-and-Software/NI-SwitchExec-with-3499-and-IVIDriver/td-p/1827...

  Finally: You can communicate with the MAX card?  Or is the occurrence of the error in MAX?  What language do you use to talk to the card with?  Using IVI?  If you are using LabVIEW or CVI then open examples of shipping and test them with this card.

  Kind regards

• LabVIEW: Unspecified error (Hex 0x80004005). = OR System Configuration: various failure (Hex 0x80004005).

  Hello:

  I get this error when you try to run the main.vi

  I am able to run the program from my computer at work fine. I then copied the files on another computer in our laboratory. Click on the arrow of the execution and the deployment progress window appears. Deployment status reads as follows:

  Initializing...

  Calculating dependencies...

  LabVIEW: Unspecified error (Hex 0x80004005).

  ========================

  System OR Configuration: Various operating default (Hex 0x80004005).

  I've been to the measurement and Automation Explorer and installed / reinstalled the system software to remotely on computers and that they are corresponding versions.

  Any help would be greatly appreciated.

  With the help of technical support NOR, I think we have found a solution. We uninstalled Labview from the computer. We have then reinstalled in the following order. 1 install the labview development environment in 2015. 2. install the real time module. 3. install the FPGA. 4 drivers CompactRIO. We installed these one at a time to make sure they were installed in the correct order, and it seems to have solved our problems. Thank you.

• NI LabVIEW driver for the SRS DS345 function generator generates error "(Hex 0xBFFF0011) insufficient location information or the device or resource is not present in the system."

  Hello

  We have a generator function SRS DS345.

  I just downloaded the driver NOR for the instrument on http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=E3B19B3E9149659CE034080020E748....

  After installation, the DS345 appears in MAX, and I can well communicate with him.

  However, if I run the srds345 to Started.vi, I get an error "location information insufficient (Hex 0xBFFF0011) or the device or resource is not present in the system" from initialize it with Options.vi srds345 sub - vi.

  The only change I did Exchange address GPIB 14 to 19, which is our function generator GPIB address. In addition, the

  Functions of SRS DS345 generator of function palette is empty, even after you restart LabVIEW (see attachment). I'm using LabVIEW 8.5.1.

  Your help in resolving this issue is appreciated. Thank you.

  Best regards

  Peter

  Have you installed the driver from LabVIEW or copied directly from inst.lib?

  The first is easier, and you don't have to restart LV more...

  Error in a not filled gpib address points. I have not checked if this driver has a resource name visa or a string of gpib address old but in the first case, try the little triangle on the right at the slect address instead of by hand.

• Error (Hex 0xBFFF0015) time-out in NI VISA test panel when you try to play the system

  Hello

  I try to control the position of three valves actuator of four lanes of Garland. They are VICI Valco and model # EUHA. I connected them via RS - 232 to USB in my computer. I was able to communicate with them, when I sent a few simple commands through hyperterminal and when I open MAX devices appear and the sign says the devices are working properly. However, when I go in the test panel and try to run some of the default commands, I get timeout error, 0xBFFF0015, during the reading of the order. Thanks for any help you can provide.

  To get your LabVIEW code, you right-click on the control/string constant and select '-' display Codes?

• Timeout error Hex 0xBFFF0015 read problem

  
  
  

• Shared data varying variable published network write error

  In my project in real time, on the VI host running on my Windows PC, I try to write in a number of published network shared variables.  All these write operations are successful (which means that I can read them on the RT target, then a cRIO-9012), except for these shared variables network-published with data type defined as Variant.  I'm not sure what is causing the problem.

  I take the table of clusters shown here...

  

  .. .and going through one "in Variant' VI and then subsequently in writing to the shared variable (data type: Variant).  Diagnosis of the failure of the VI in real-time to read the data, I found that variable writing shared on the host VI produced the following error:

  Error - 2147467259 appeared to Variable shared in the PC host TTS CTRL.vi

  Possible reasons:

  LabVIEW: Unspecified error (Hex 0x80004005).
  =========================
  System OR Configuration: Various operating default (Hex 0x80004005).

  This error or warning occurred when writing the following shared Variable:
  Shared \\My Computer\Network Variables\TC trust Array Group - network
  Shared \\128.144.90.143\Network Variables\TC trust Array Group - network

  .. where 128.144.90.143 is the IP address of the PC.

  Any thoughts?

  Sean

  I saw this post, and when I found myself with no other option, I have redefined the variables in question to the string data type and replaced all the "to variant" and "given Variant of ' functions with functions 'Flatten channel' and"The string Unflatten"respectively.  Initially, it did not work - functions "Chain Unflatten" would produce error 74, until I realized that the "data includes array or string of size? (T)"input on each 'string Unflatten" function must be set to FALSE. Wiring a constant false for each instance of "Unflatten to the string" seems to have corrected the problem.

  I have still no idea why wouldn t Variant.  Shared variables Editor allows to define a variant data type, so I guess it's supposed to?

  Sean

• Cannot undeploy SoftMotion axis: Hex 0x80004005

  Hello

  I used a cRIO-9076, NI 9505 + SoftMotion for a project. Now, I would like to reuse the material for a new project.

  The old project was an axis SoftMotion (unbound), who refuses to be cancelled. According to the dialog box comparison system & project, the existence of this axis on the cRIO is the only thing that does not match my new project. However, when I select "Undeploy" and click on "Apply", I get this:

  Initializing...
  The checking for conflicts. This may take some time...
  Undeploying axis 1
  LabVIEW: Unspecified error (Hex 0x80004005).
  =========================
  System OR Configuration: Various operating default (Hex 0x80004005).
  Cancel the deployment completed with errors

  I have tried with no luck:

  • Turn the power off then by restarting the cRIO both my PC
  
  
  • Put the scan engine cRIO from Active mode to setting mode

  Any tips? I'm under LabVIEW 2012 (some other versions exist on the development PC).

  Hello JKSH,

  It seems that your deployed data has been corrupted somehow. You can try to delete the data to deploy manually.

  1 - FTP to your 9076

  2 remove the contents of the directory/nor-rt/config

  3 - restart the target

• IVI, error-1074130425

  I use LabView 8.5 Pro with IVI Compliance Package 4.3. I'm trying to simulate a DMM using class IVI drivers. I get the following message:

  Error 1074130425 has occurred to be initialized with Options.vi IviDmm,

  Possible reasons:

  The primary error: (Hex 0xBFFA1207) the item does not exist in the collection.

  Complete the call chain: IviDmm initialize with Options.vi DMM Sim.vi

  In MAX, under the logical names of IVI, I created the logical name DMM and created pilot Sessions the dsDMM of the session that I configured in fake it with drop-down list to use nisDMM. I didn't put no other options in any screen or category. The logical name of the Initialize vi is set on DMM.

  You can specify a beginner in the right direction, please?

  -John

  John,

  You can find much more information on the page of the Instrument Driver Network instrument drivers on ni.com (http://www.ni.com/idnet). In particular, take a look at the section 'with the help of pilots.

• Error SSE2 optimization in the deployment of Web Services

  I'm migrating from 2010 to 2011 SP1 web service [because web services 2010 SP1 were buggy]. At first, I could build and deploy the code very well. Now, I get the following deployment error:

  LabVIEW error: (Hex 0xFFFEFA45) LabVIEW Web Services: call to create a VI reference failed. The target does not support SSE2 optimization. Disable SSE2 optimization in the Advanced dialog box of the Web Service Properties page before continuing.

  Based on the online documentation, my hardware can support SSE2 - but no matter, I disabled it anyway. The error message persists. This message means anything this SSE2 optimization is enabled and is not supported? Based on the text of the error, it seems that turning off optimization should probably fix the problem...

  
  

• Agilent Power Supply E3645A IVI Driver Communication error

  Hello world

  I'm trying to communicate to Agilent power using IVI Drivers. I join you MAX Report, all the modules installed on the system.

  When I run initialization of the VI for Agilent power, using the simulation with 'Specific Driver', no errors appear. But when I select "do not simulate", I get this error:

  Initialize IviDCPwr with Options.vi
  The primary error: (Hex 0xBFFA0011) function or method not supported.
  Development: FunctionId: 3, FunctionName: InitWithOptions

  Communicate with instruments instrument using Driver works fine, but using the Drivers IVI is not.

  I tried all the steps in this topic .

  PROMT any help will be highly appreciated.

  Kind regards.

  Shane5ab

  Hello, Tanguy,.

  I am pleased that install the specific instruments IVI - C Driver took care of things.  The differences between IVI - C and IVI - COM can be confusing at first.  I hope the rest of your application development goes smoothly.

  See you soon,.

  NathanT

• Deployment complete with static Variables cRio-9074 network errors, pc with executable file

  Hello.

  I am building an application runs on a machine without LabVIEW development system and connect via the network shared a cRIO Varibles (RT FIFO). I can successfully create an installer and EXE for PC and a RTEXE for the cRio. When I run on my development computer, the application is able to communicate using variables shared without a problem.

  But, when I install my application on another computer and connect the cRIO, I get the following error when you deploy shared variables when the application starts:

  Initializing...

  Calculating dependencies...

  The checking for conflicts. This operation can take a long time.

  Preparation itesm by download. This operation can take a long time.

  Deployment 169.254.84.198

  Deployment VariableLib.lvlib\\169.254.84.198\VariablesLib (:-2147467259,)

  LabVIEW: Unspecified error (Hex 0 x 800004005).).

  Completed with errors of deployment

  I created an exception in the Windows Firewall configuration. I have included the library of VariableLib on the EXE of RT, outside and inside the exe file to c:\.

  I am downloading the SP1 for LabVIEW and Module RT and decided to reinstall all the software on my cRio.

  Any help will be appreciated.

  Hello Luis.

  Thank you very much for your help. The Variable engine OR has been and should be included in the intallation.

  I was able to get the application running. I installed the System Manager distributed on the PC without LabVIEW to control if the library has been get deployed. Using what I found that another device on the network use the same IP address as the cRio and so the IP address has been lying to the deployment, but the device has returned an error. I just changed the IP address on the cRio and I was good to go. I have not reproduced on both devices such as network shared Variables suggests on some positions, nor I needed to modify the ALIAS files on devices.

  Best regards and thanks again for your time.

• I tried a simple snap vi and everything I had, it was a weird error message

  Hello

  so I installed the acquisition of vision, vision Assistant and connected to the camera. And when I run a simple vi snap I get this error message:

  Hello

  so I installed the acquisition of vision, vision Assistant and connected to the camera. And when I run a simple vi snap I get this error message:

  Error - 2147467259 occurred ar IMAQdx Open Camera.avi

  Possible reasons:

  LabVIEW: Unspecified error (Hex 0x80004005).
  =========================
  System OR Configuration: Various operating default (Hex 0x80004005).

  Hello

  so I installed the acquisition of vision, vision Assistant and connected to the camera. And when I run a simple vi snap I get this error message:

  Error - 2147467259 occurred ar IMAQdx Open Camera.avi

  Possible reasons:

  LabVIEW: Unspecified error (Hex 0x80004005).
  =========================
  System OR Configuration: Various operating default (Hex 0x80004005).

  Now when I go to MAX I can see the camera under NOR-IMAQdx devices, but it has a small red circle with a white cross. I went through the help, but I must be missing something because he said that I should do a right-click on the camera and go Driver"digital camera NOR-IMAQdx IIDC. There is no driver when I right click on the camera and I end up getting a different error message say:

  Error 0 x 80004005

  Unknown error code in imgShowError.

  Hello

  so I installed the acquisition of vision, vision Assistant and connected to the camera. And when I run a simple vi snap I get this error message:

  Error - 2147467259 occurred ar IMAQdx Open Camera.avi

  Possible reasons:

  LabVIEW: Unspecified error (Hex 0x80004005).
  =========================
  System OR Configuration: Various operating default (Hex 0x80004005).

  Now when I go to MAX I can see the camera under NOR-IMAQdx devices, but it has a small red circle with a white cross. I went through the help, but I must be missing something because he said that I should do a right-click on the camera and go Driver"digital camera NOR-IMAQdx IIDC. There is no driver when I right click on the camera and I end up getting a different error message say:

  Error 0 x 80004005

  Unknown error code in imgShowError.

  So I had two error messages & I'm sure it's the same problem. He need to apologize that I am kinda new to this more - as most of you are I am self-taught, so I'm still rough around the edges.

  
  

• Shared Variable deployment error

  I need to use Variables shared in my code, and when I try to run the code I get the following error.

  My computer deployment
  Ventilation Library.lvlib\\169.254.192.23\Ventilation library of deployment deployment has failed (error:-2147220712, MAX: internal error (Hex 0 x 80040318): the customer has failed to connect on the server configuration, perhaps because the server is too busy or encountered an error of communication.) Note: the steps that you did which led to this error and contact technical support).
  Completed with errors of deployment

  The code was working yesterday with shared variables, but it won't deploy today and I can't imagine any changes that I made to do this. I tried to run the code on my cRIO and the PC. I have used amd 2015 2014 and I get the same error on all.

  Any help with this problem would be great.

  What is the IP 169.254.192.23? It looks like an auto-negotiation-to-peer (e.g., crossover) connection IP or the IP address of your computer on the network?

  Is the library with shared variables located under 'my computer '? If you right click on 'my computer' in the project - he shows here? IP address you think it correct?

  If you check the custom address 'specify' and put 127.0.0.1 (loopback IP address), it works?

  I also look in Windows Services and verify that the shared Variable service (and other services OR that it requires) are running.

• Shared library error Variable deployment-2147220735

  I had to reinstall my whole LabVIEW installation, where my SSD was about to fill. I uninstalled everything and freshly installed everything on a larger hard drive. Unfortunately, I now get an error message and am wondering what I have to reinstall.

  When I want to deploy a library shared in LabVIEW 2014 32-bit Variable, it returns an error:

  Initializing...
  Calculating dependencies...
  The checking for conflicts. This may take some time...
  Prepare the items for download. This may take some time...
  My computer deployment
  Deployment deployment test.lvlib\\10.0.10.45\test failed (error:-2147220735, MAX: internal error (Hex 0 x 80040301): the specified class is not found in the configuration database.) Your installation may need to be repaired.).
  Completed with errors of deployment

  

  Any suggestions?

  Have you tried a repair, which sometimes works but sometimes a completely uninstall and reinstall is necessary. Have you tried to repair only the proposed below KB file?

  http://digital.NI.com/public.nsf/allkb/67E896D850D988C286257811005FEFF5?OpenDocument

  As you can see the same error in Distributed System Manager the quickest solution would probably be to uninstall LV and the drivers and reinstall them just. If the KB above does not work.