Error of tunneling to ASA 5505 using "Software VPN Client"
Here's my current network:
I'm VPN tunnel in the ASA using the Cisco VPN Client software.
Here is my config ASA config: http://pastebin.com/raw.php?i=ad6p1Zac
Here's my entry for the VPN Client connection information:
(Password: cisco)
When I try to connect, I get the message error "the received HASH load cannot be verified.
What is this error and how can I solve it?
I think you need to enter this information in the fields of group authentiation:
(Just below "Group authentication")
Name: vpnclientgroup
Password: [just what you entered as a pre shared key below]
tunnel-group vpnclientgroup ipsec-attributes pre-shared-key *****
After the establishmet tunnel you will get a password pop up, that you enter "David" and the associated password.
Tags: Cisco Security
Similar Questions
-
CISCO ASA 5505 no cisco VPN Client
Hello
I'm looking for after a firewall Cisco ASA 5505 and want to watch all the owners of it with remote access in but none of us have a support contract with Cisco.
Is it possible to set up a VPN client not as Microsoft built the client to connect to the ASA?
Thank you
Alamb200
Hello
Looking for a PPTP on ASA connection?
The following document provides the following:
ASA q support PPTP client?
A. number of the
But we can configure ASA to allow the PPTP connection:
I hope this helps.
Kind regards
Anisha
P.S.: Please mark this thread as answered if you feel that your request is answered. Note the useful messages.
-
IP address connection sets using the VPN Client
Hello world. I'm using a VPN Client when I establish a VPN Tunnel with a 1600 router, and I have a question.
Can I assign a fixed IP address in the client, instead the router send to random addresses from customer?
What I would he do this?
It would be in the configuration of the VPN client, or in the configuration of the router?
If so, I'm doing this?
Do I need another tool, or other software or hardware to do?
any help is hope...
Thank you...
Hello
I don't think that there is a simple way to do this.
However, if you create a different groupname for the user who needs a static IP address, I think you should be good to go
So what you need to do, create a new pool of addresses. Make the start and end ip address be the same (this is the address to which you want to assign to the VPN user)
Configure another ipsec on the router group and bind the new pool to this group
Ask your VPN client to connect to this group
Hope that helps
Jean Marc
-
ASA problem inside the VPN client routing
Hello
I have a problem where I can't reach the VPN clients with their vpn IP pool from the inside or the asa itself. Connect VPN clients can access internal network very well. I have no nat configured for the pool of vpn and packet trace crypt packages and puts it into the tunnel. I'm not sure what's wrong.
Here are a few relevant config:
network object obj - 192.168.245.0
192.168.245.0 subnet 255.255.255.0
192.168.245.1 - 192.168.245.50 vpn IP local pool
NAT (inside, outside) static source any any destination static obj - 192.168.245.0 obj - 192.168.245.0 no-proxy-arp-search to itinerary
Out of Packet trace:
Firewall # entry packet - trace inside the x.x.x.x icmp 8 0 192.168.245.33
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit rule
Additional information:
MAC access list
Phase: 2
Type:-ROUTE SEARCH
Subtype: entry
Result: ALLOW
Config:
Additional information:
in 192.168.245.33 255.255.255.255 outside
Phase: 3
Type: ACCESS-LIST
Subtype: Journal
Result: ALLOW
Config:
Access-group acl-Interior interface inside
access list acl-Interior extended icmp permitted an echo
Additional information:
Phase: 4
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional information:
Phase: 5
Type: INSPECT
Subtype: np - inspect
Result: ALLOW
Config:
Additional information:
Phase: 6
Type:
Subtype:
Result: ALLOW
Config:
Additional information:
Phase: 7
Type: NAT
Subtype:
Result: ALLOW
Config:
NAT (inside, outside) static source any any destination static obj - 192.168.245.0
obj - 192.168.245.0 no-proxy-arp-search to itinerary
Additional information:
Definition of static 0/x.x.x.x-x.x.x.x/0
Phase: 8
Type: VPN
Subtype: encrypt
Result: ALLOW
Config:
Additional information:
Phase: 9
Type: CREATING STREAMS
Subtype:
Result: ALLOW
Config:
Additional information:
New workflow created with the 277723432 id, package sent to the next module
Result:
input interface: inside
entry status: to the top
entry-line-status: to the top
output interface: outside
the status of the output: to the top
output-line-status: to the top
Action: allow
There is no route to the address pool of vpn. Maybe that's the problem? I don't know than that used to work before we went to 8.4.
Check if the firewall is enabled on your host from the client ravpn and blocking your pings.
-
Different classes using Cisco VPN Client VPN
Hello
on a cisco ASA 5510, I defined a vpn group used for remote teleworkers who have access to the entire LAN using Cisco VPN Client 4.8.
I would give to others of this client, but I need to limit their access to LAN resources, which means that I have to have two types of users:
Remote LAN access
access to only certain IP addresses
Both must use the Cisco VPN client.
How can I do?
Thank you
This link should help.
-
Using Cisco VPN Client in Windows 7 Professional 64 bit
Hi all!
I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problemOpen the XP VM itself, do not use the shortcut that was published in
the W7 boot menu. You need to install Outlook / your email client
Inside the virtual machine, as well as on the side of W7. You can point to the same
PST files if you have local PST files, but you just can't open them in
at the same time of W7 and XP VM.There is no way to bridge using the shortcut of publishing app
Some people have reported success with the third party IPSec
replacements as customer universal shrew or the NCP. Your IT Department.
would like to know if these are supported:
> Hello all! I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem
Barb Bowman www.digitalmediaphile.com -
Slow initial connection using Cisco VPN Client
I am currently using Cisco VPN Client v5.0.07.0290. Whenever I start my connection, it takes me about 90 seconds for the prompt to display authentication and another ~ 90 seconds to finish the auth. and connect successfully. I have another computer laptop w / the same WIN7 OS and version of Cisco VPN Client and he ends the connection to<30 sec. ="" why="" is="" this? ="" any="" suggestions="">30>
Hi Sergio,
You import the .pcf for the VPN Client file? If so, please try to recreate a new file .pcf locally on the machine itself and try to connect. Let me know how it goes.
Thank you
Delvallée
-
LAN to Lan tunnel between ASA 5505 and 3030.
I am unable to build a tunnel vpn site-to-site between an ASA 5505 and our Cisco 3030. I tried all possible combinations except one that will work. I am able to ping each peer on the other site. Someone at - it a config between two tunnels of Lan to Lan to work between a 5505 and 3030 that works. Thank you
Hello
Please visit this link using config:
http://www.Cisco.com/c/en/us/support/docs/security/VPN-3000-series-conce...
Kind regards
Aditya
Please evaluate the useful messages.
-
ASA 5505 - remote access VPN to access various internal networks
Hi all
A customer has an ASA 5505 with a remote access vpn. They are moving their internal network to a new regime and that you would be the users who come on the vpn to access the existing and new networks. Currently can only access the existing. When users connect to access remote vpn, the asa gave them the address 192.168.199.x. The current internal network is 200.190.1.x and that they would reach their new network of 10.120.110.x.
Here is the config:
:
ASA Version 8.2 (5)
!
ciscoasa hostname
enable encrypted password xxx
XXX encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 200.190.1.15 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address 255.255.255.0 xxxxxxx
!
exec banner the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED
connection of the banner the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED
banner asdm the ACCESS NOT AUTHORIZED IS STRICTLY PROHIBITED
passive FTP mode
access extensive list ip 200.190.1.0 inside_access_in allow 255.255.255.0 any
outside_access_in list extended access permit icmp any external interface
access extensive list ip 192.168.199.0 outside_access_in allow 255.255.255.192 host 10.120.110.0
Standard access list MD_IPSEC_Tun_Gp_splitTunnelAcl allow 200.190.1.0 255.255.255.0
MD_IPSEC_Tun_Gp_splitTunnelAcl list standard access allowed host 10.120.110.0
access extensive list ip 200.190.1.0 inside_nat0_outbound allow 255.255.255.0 192.168.199.0 255.255.255.192
inside_nat0_outbound list extended access allowed host ip 10.120.110.0 192.168.199.0 255.255.255.192
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
mask 192.168.199.10 - 192.168.199.50 255.255.255.0 IP local pool Remote_IPSEC_VPN_Pool
IP verify reverse path to the outside interface
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 200.190.1.0 255.255.255.0
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 190.213.43.1 1
Route inside 10.120.110.0 255.255.255.0 200.190.1.50 1
Route inside 192.168.50.0 255.255.255.0 200.190.1.56 1
Route inside 192.168.60.0 255.255.255.0 200.190.1.56 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
http server enable 10443
http server idle-timeout 5
Server of http session-timeout 30
HTTP 200.190.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Dynamic crypto map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint _SmartCallHome_ServerCA
Configure CRL
Crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
(omitted)
quit smoking
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Crypto isakmp nat-traversal 3600
Telnet timeout 5
SSH 200.190.1.0 255.255.255.0 inside
SSH timeout 5
SSH version 2
Console timeout 5
dhcpd outside auto_config
!
a basic threat threat detection
scanning-threat shun threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
internal MD_SSL_Gp_Pol group strategy
attributes of Group Policy MD_SSL_Gp_Pol
VPN-tunnel-Protocol webvpn
WebVPN
list of URLS no
disable the port forward
hidden actions no
disable file entry
exploration of the disable files
disable the input URL
internal MD_IPSEC_Tun_Gp group strategy
attributes of Group Policy MD_IPSEC_Tun_Gp
value of banner welcome to remote VPN
VPN - connections 1
VPN-idle-timeout 5
Protocol-tunnel-VPN IPSec webvpn
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list MD_IPSEC_Tun_Gp_splitTunnelAcl
the address value Remote_IPSEC_VPN_Pool pools
WebVPN
value of the RDP URL-list
attributes of username (omitted)
VPN-group-policy MD_IPSEC_Tun_Gp
type of remote access service
type tunnel-group MD_SSL_Profile remote access
attributes global-tunnel-group MD_SSL_Profile
Group Policy - by default-MD_SSL_Gp_Pol
type tunnel-group MD_IPSEC_Tun_Gp remote access
attributes global-tunnel-group MD_IPSEC_Tun_Gp
address pool Remote_IPSEC_VPN_Pool
Group Policy - by default-MD_IPSEC_Tun_Gp
IPSec-attributes tunnel-group MD_IPSEC_Tun_Gp
pre-shared key *.
!
!
context of prompt hostname
: end
The following ACL and NAT exemption ACL split tunnel is incorrect:
MD_IPSEC_Tun_Gp_splitTunnelAcl list standard access allowed host 10.120.110.0
inside_nat0_outbound list extended access allowed host ip 10.120.110.0 192.168.199.0 255.255.255.192
It should have been:
Standard access list MD_IPSEC_Tun_Gp_splitTunnelAcl allow 10.120.110.0 255.255.255.0
access extensive list ip 10.120.110.0 inside_nat0_outbound allow 255.255.255.0 192.168.199.0 255.255.255.192
Then 'clear xlate' and reconnect with the VPN Client.
Hope that helps.
-
Cisco asa 5505 and centos VPN server connection
Hi all
Please I want to set up a VPN between Cisco asa 5505 and centos server.
Here's my senerio
-------------------------
ASA 5505
Public IP 155.155.155.2
Local NETWORK: 192.168.6.X
CentOS Server
------------------
Public ip address: 155.155.155.6
Thank you guys
Apology, do you mean access remote VPN Client of hundred BONE for Cisco ASA 5505?
If the remote access, here are the sample configuration:
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a008060f25c.shtml
-
Is it possible to use a private network virtual created with the WRVS4400N router with VPN Client from Cisco Systems (ver 5) software? (Although QuickVPN works very well.)
Is it possible to use with Account customer VPN mode? Or is it possible to use with IPSec VPN (Tunnel) mode? If so, please provide together how to client-side and the router. Thank you!
Unfortunately Small Business routers are not compatible with the Cisco VPN Clients. The Cisco VPN Clients have more parameters that are not available in the materials of the series of small businesses, so all we can use is the application of QVPN.
-
ASA 5510 &; Windows XP VPN Client
I want to use the VPN in Windows XP client to connect to the ASA
VPN access
. I read the document after document, and I just can't get to work. It seems what Phase 1 but I can't get the Phase 2. In the logs ASDM, it shows that I get some QM WSF Errorsand on the Windows XP computer, I get an error 789. I put the pre-shared on the XP machine as a result and another j.4 measures.I am quite new to the method of L2TP VPN, I've always used Windows Server for the VPN and now I am to find out why. In any case, I'm sure I'm missing some info that is needed to diagnose, but here's a copy of my config.
I hope someone can point me in the right direction to understand this because I am pulling my hair out!
Thanks in advance!
This set of transformation is fixed for the transport mode but not used.
Crypto ipsec transform-set esp-3des esp-sha-hmac TRANS_ESP_3DES_SHA ikev1
transport mode encryption ipsec transform-set TRANS_ESP_3DES_SHA ikev1First, it must ensure that it is used in the list of games to turn in 'dynamic crypto-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set... ». L2TP/IPSec requires this mode.
If it still fails, try to get him debugs following during the connection to your customer.
Debug crypto isa 127
Debug crypto ipsec
Debug aaa 127 Commons
SPSP
-
Itineraries other nets will be lost when using the vpn client?
I have a very general question. I intend to implement a security solution for the extranet partners to connect to our intranet using VPN client. IPSec will close on the external interface of the Cisco PIX firewall v6.3.
Now, my consirn is, I downloaded the vpn client to test but I saw no advance settings to define what network traffic will pass through the IPSec tunnel and which will be routed normally. Is it by default all traffic passing through VPN? Is that what it means if there are other networks using their default route, they will not be able to achieve? (i.e. the Internet).
Thank you.
That would depend on how you set up the PIX. You can allow the VPN to your site and access to the Internet at the same time. This is called the split tunneling. It is configurable on the PIX, not the customer.
This link might help you get started, but I'm sure that there stronger links.
-
Dear all,
I have cisco vpn client v5.0.05.
1 / when I lunch the customer, it connect to the asa, so I can't reach the network behind my ASA
2 / when connected to the vpn client, I can not use my access to the internet, I configured splitunnel, but does not.
3 / sometimes, cisco vpn client disable my network ip of the gateway card.
Please, can someone help me?
Concerning
Can you please share the configuration of the SAA. There is no specific configuration that must be done on the vpn client.
-
configuration problem pix515 to access remote vpn using the vpn client
Hello
My chart is simple:
a client pc with customer vpn cisco 3.X
try to connect to a remote site via a pix 515E.
What happened:
the pc can connect, the pix give it an ip address, but no traffic not encrypted so no access to the remote network.
My config is:
---------------------------------------
START THE CONFIG
--------------------------------------
access-list 102 permit ip 192.168.80.0 255.255.255.0 10.10.10.0 255.255.255.0
IP local pool clientpool 10.10.10.5 - 10.10.10.50
NAT (inside) - 0 102 access list
Permitted connection ipsec sysopt
Crypto ipsec transform-set robust esp - esp-md5-hmac
Crypto-map dynmap 10 transform-set robust Dynamics
map mymap 10-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
ISAKMP allows outside
ISAKMP identity address
part of pre authentication ISAKMP policy 10
encryption of ISAKMP policy 10
ISAKMP policy 10 md5 hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
vpngroup address clientpool pool vpn30002
vpngroup password 123daniel456789 vpn30002
vpngroup split tunnel 102 vpn30002
-------------------------------------
END CONFIG
-------------------------------------
Please help me!
Concerning
Can you upgrade to a new vpn client or try to disable the firewall in XP sp 2? I think the problem is that this old clients are not supported on xp sp2 or will have problems with the firewall in SP2. Try to run a higher customer or 4.0 x.
Maybe you are looking for
-
How can I get my trackpad to change size?
With Safari, I can do a two finger spread to change the size of my window. With Firefox, I have to use control and + or - to do this.Is there a way to get it with Firefox?
-
Thunderbird 17.0.8 refreshes The lightning will not work with it.
I have Thunderbird version 17.0.8 I have tried several times to update. I'm on Windows 7 Home Premium. I also tried to install the calendar of lightning, which apparently worked, but he will allow no data entry. In other words, it is apparently here
-
I have laptop lenovo T450 using nomally after I stop and keep unused around 3-4 days and I take it to use it cannot open and after I plug the power adapter into the machine, he can open nomally. I check have the battery he opened, check the battery,
-
I had to have my hard drive replaced and the company that made him put two versions of 32-bit and 64-bit Vista Home Premium on it. Soon, I discovered that I was getting conflict on my computer and he discovered that the two were on the hard drive.
-
Custom ActiveTextHandler: handle #hashtag and @mention in the label
Hi all Can we do a manager of custom text in the Label control? Example: I want to handle '#somehashtag' or '@someuser' when'm typed by the user. Currently, only html like 'http' if I using standart ActiveTextHandler, tag would get shares. Thank you.