Slow initial connection using Cisco VPN Client

Similar Questions

• Using Cisco VPN Client in Windows 7 Professional 64 bit

  Hi all!
  I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem

  Open the XP VM itself, do not use the shortcut that was published in
  the W7 boot menu. You need to install Outlook / your email client
  Inside the virtual machine, as well as on the side of W7. You can point to the same
  PST files if you have local PST files, but you just can't open them in
  at the same time of W7 and XP VM.

  There is no way to bridge using the shortcut of publishing app

  Some people have reported success with the third party IPSec
  replacements as customer universal shrew or the NCP. Your IT Department.
  would like to know if these are supported

  :

  > Hello all! I need to use Cisco VPN Client to connect to my server in the company, because my company uses lotus notes Server, I have to connect Cisco VPN to access e-mail. But now my windows version is Windows 7 Pro 64 bits that cannot directly install this application, I already installed XP Mode and creatde shortcut to Windows 7, I plugged the Cisco VPN to my Cisco VPN server, but I can not access the server, Pls help me and show me how to solve this problem
  Barb Bowman www.digitalmediaphile.com

• Different classes using Cisco VPN Client VPN

  Hello

  on a cisco ASA 5510, I defined a vpn group used for remote teleworkers who have access to the entire LAN using Cisco VPN Client 4.8.

  I would give to others of this client, but I need to limit their access to LAN resources, which means that I have to have two types of users:

  Remote LAN access

  access to only certain IP addresses

  Both must use the Cisco VPN client.

  How can I do?

  Thank you

  This link should help.

  http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a0080641a52.shtml

• Cannot use Cisco vpn client

  Dear all,

  I have cisco vpn client v5.0.05.

  1 / when I lunch the customer, it connect to the asa, so I can't reach the network behind my ASA

  2 / when connected to the vpn client, I can not use my access to the internet, I configured splitunnel, but does not.

  3 / sometimes, cisco vpn client disable my network ip of the gateway card.

  Please, can someone help me?

  Concerning

  Can you please share the configuration of the SAA. There is no specific configuration that must be done on the vpn client.

• Using Cisco VPN Client VPN

  Is it possible to use a private network virtual created with the WRVS4400N router with VPN Client from Cisco Systems (ver 5) software? (Although QuickVPN works very well.)

  Is it possible to use with Account customer VPN mode? Or is it possible to use with IPSec VPN (Tunnel) mode? If so, please provide together how to client-side and the router. Thank you!

  Unfortunately Small Business routers are not compatible with the Cisco VPN Clients. The Cisco VPN Clients have more parameters that are not available in the materials of the series of small businesses, so all we can use is the application of QVPN.

• Professional Windows Vista crashes when you use Cisco VPN Client 5.05.0290

  I have a Dell Latitude E6400 Windows Vista Business (32 bit) operating system. When I go to turn on the VPN client, I get invited to my username / password and once entered, the system just hangs. The only way to answer, it's a re-start. I took action:

  1 disabled UAC in Windows
  2 tried an earlier version of the VPN client
  3. by the representative of Cisco, I put the application runs as an administrator

  If there are any suggestions or similar stories, I would be grateful any offereings.

  It IS the COMODO Firewall with the 5.0.x CISCO VPN client that causes the gel. The last update of COMODO has caused some incompatibility. I tried to install COMODO without the built in Zonealerm, but it is still frozen. The only way to solve it is to uninstall COMODOD. Since then, my CISCO VPN client works again...

• Connection to the VPN Client 5.0.07 returns error 443 (activity included)

  I got the Cisco VPN Client to work on my windows 8.1 box, but my windows 10 box gives me some issues.

  I am trying to connect to a Cisco VPN using Cisco VPN Client 5.0.07.0290. 10 Windows.  The first Cisco VPN would not install and I discovered that I had to install Citrix DNE before installing Cisco VPN. I did it and now the Cisco VPN client installs fine.

  Now, I get an error 443 with the following log information when I try to connect:

  ---

  Config files directory: C:\Program Files (x 86) \Cisco Systems\VPN Client\
   
  1 20:31:03.517 23/07/15 Sev = WARNING/2 CVPND/0xA3400017
  Download key failed.
   
  2 20:31:03.517 23/07/15 Sev = WARNING/3 IKE/0xE3000002
  Function download_key_entry failed with the error code of 0 x 00000000(ISAWIN:346)
   
  3 20:31:03.518 23/07/15 Sev = WARNING/3 IKE/0xE3000050
  Failed to load IPsec keys
   
  4 20:31:03.518 23/07/15 Sev = WARNING/2 IKE/0xE30000A7
  SW unexpected error during the processing of negotiator fast Mode:(Navigator:2263)
   
  5 20:31:03.533 23/07/15 Sev = WARNING/2 IPSEC/0xE3700003
  Function CniMemRealloc() failed with the error code of 0 x 00000000 (IPSecDrvBSafeMem:152)
  ---
   
  in the event logs, I see the following error message:

  Service Service VPN from Cisco Systems, Inc. is marked as an interactive service. However, the system is configured to not allow interactive services. This service may not function properly.

  ----
  Things I've tried:
   
  I took the SSL certificate to my computer that works (windows 8.1) and installed on my machine Windows 10 and ensured that it was valid. I then imported it in the Cisco client. It did not work.
   
  I checked the registry to ensure there was incorrect data in the DisplayName value, and that works.
   
  Any thoughts on what I might try next?

  Hello Onimallar,

  I had this same problem with my Windows 64-bit 10.  But on my 32-bit Windows 10 VM the Client VPN Cisco worked OK.  So I looked into the differences.  It seems that Setup 64-bit VPN client cannot change the network settings to add the network client 'DNE light filter' required for the properties of the network adapter.

  I tried the Citrix DNE update, and while that helped Cisco VPN Client install successfully on my 64-bit machine, it would not establish a connection.

  Using the differences, I removed the two of the DNE Updater and Cisco VPN Client, and then installed 64-bit Dell SonicWall VPN Client, as this has been installed in my VM 32 bits (the 32-bit version).  This added the workstation network DNE filter of my 64-bit machine.  I reinstalled the Cisco VPN Client successfully and was able to connect to a remote site with success.

  It worked for me.

  You can download the SonicWall VPN Client from:

  https://support.software.Dell.com/SonicWALL-Global-VPN-client/Windows%20...

• Cisco VPN Client follow-up

  Hello

  I have a Cisco 2821 and ASA 5510 VPN router in my network.

  Our remote users are using Cisco VPN Client 5.0.07 and I need to track on a server and keep their login information to generate reports for my manager.

  Could you please let me know how I can do this trick of surveillance?

  Thank you

  Mike

  It can be done by choosing one of three types of monitoring of the performance of the VPN:

  http://www.Cisco.com/en/us/docs/net_mgmt/vpn_solutions_center/1.1/user/guide/VPN_UG5.html

  I hope this helps!

• Unable to connect using the Cisco VPN client

  Hi all. I recently configured a 5510 ASA to allow remote access using the Cisco VPN client. The problem is that everything works fine when I connect using a modem classic or on a computer with a public address that I use for testing purposes, but whenever I try to connect with on an ADSL line, I can't access to the resources. I have connection and after that nothing, I can not achieve anything.

  I enclose the relevant configuration information in the attachment. Any help is welcome.

  Depending on the version, add...

  ISAKMP nat-traversal

  or

  ISAKMP nat-traversal crypto

  Should be all you need.

• Problems to connect via the Cisco VPN client IPSec of for RV180W small business router

  Hello

  I tried to configure my router Cisco of RV180W as a customer VPN IPSec, but have encountered a problem that I hope someone can help me with. "" I managed to do the work of configuration so that the Cisco's VPN IPSec client authenticates successfully with the XAUTH user, I put on the router, but during the negotiation, the client ends with the following, which appears several times on the router error message: ' Mar 20 Oct 19:41:53 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [34360] has no config mode.

  I've read around the internet and a number of people seem to say that the Cisco VPN Client is not compatible with the router, but the same thing happens to my iPhone VPN client.

  Is it possible that this can be implemented? Below, I have attached the full configuration files and the log files. Thank you much in advance.

  Router log file (I changed the IP addresses > respectively as well as references to MAC addresses)

  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: floating ports NAT - T with counterpart > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] WARNING: notification to ignore INITIAL-CONTACT > [44074] because it is admitted only after the phase 1.
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [4500]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT - D payload does not match for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received unknown Vendor ID
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: received Vendor ID: CISCO-UNITY
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: NAT detected: is located behind a device. NAT and alsoPeer is behind a NAT device
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: request sending Xauth for > [44074]
  Mar 20 Oct 20:03:10 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association established for > [4500] -> [44074] with spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REPLY' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: login successful for the user "myusername".
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser connected from the IP >
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: sending of information Exchange: Notify payload [10381]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: receives the type of the attribute 'ISAKMP_CFG_REQUEST' of > [44074]
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: ignored attribute 5
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28683
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] WARNING: attribute ignored 28684
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no config mode
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: local configuration for > [44074] has no mode config
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] ERROR: remove the invalid payload with doi:0.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: purged-Association of ISAKMP security with proto_id = ISAKMP and spi =>.
  Mar 20 Oct 20:03:15 2015 (GMT + 0000): [r1] [IKE] INFO: myusername XAuthUser Logged Out of the IP >
  Mar 20 Oct 20:03:16 2015 (GMT + 0000): [r1] [IKE] INFO: ISAKMP Security Association deleted for > [4500] -> [44074] with spi =>

  The router configuration

  screen_shot_10-20 - 15_at_09.00_pm.png

  

  IKE policy

  screen_shot_10-20 - 15_at_09.00_pm_001.png

  

  screen_shot_10-20 - 15_at_09.01_pm.png

  

  VPN strategy

  screen_shot_10-20 - 15_at_09.02_pm.png

  

  screen_shot_10-20 - 15_at_09.02_pm_001.png

  

  Client configuration

  Hôte : < router="" ip=""> >

  Authentication group name: remote.com

  Password authentication of the Group: mysecretpassword

  Transport: Enable Transparent Tunneling; IPSec over UDP (NAT/PAT)

  Username: myusername

  Password: mypassword

  Please contact Cisco.

  Correct, the RV180 is not compatible with the Cisco VPN Client.  The Iphone uses the Cisco VPN Client.

  You can use the PPTP on the RV180 server to connect a PPTP Client.

  In addition, it RV180 will allow an IPsec connection to third-party customers 3.  Greenbow and Shrew Soft are 2 commonly used clients.

• Cisco vpn client is supported on the analogue ppp connection

  can someone pls tell me if we can use the client vpn cisco on a ppp connection analog and put a pix that is not PPPs running. If it works, then why do we need to VPN L2tp/ipsec. can someone pls tell me something abt it. It is very urgent.

  concerning

  Assane

  Assane,

  If I understand your question, you speak with PPP initially to get an IP address from your service provider, then use the Client VPN VPN in your Pix Firewall. If so, yes it is possible.

  To name a few reasons why PPTP or L2TP/IPSEC is used instead of Cisco VPN Client are:

  1. because companies have used a PPTP or L2TP/IPSEC solution for some time and are migrating to Cisco VPN

  2. do not install vpn on the PC client software

  3. won't pay for the VPN Client software licenses

  Let me know if it helps.

  Kind regards

  Arul

• Unable to connect via the Cisco VPN Client

  Hello

  I have configured remote access VPN to ASA and tries to connect via the Cisco VPN Client 5.0

  I am not able to connect and watch the journal on the SAA

  ASA-3-713902: Group = xxxxx, IP = x.x.x.x, withdrawal homologous peer table is placed, no match!

  ASA-4-713903: Group = xxxxx, IP x.x.x.x, error: impossible to rmeove PeerTblEntry

  ASA does not support the K9 i.e. VPN - DES is enabled and VPN-3DES-AES is disabled.

  What could be the reason.

  Concerning

  Hi, I had this same problem, here is the solution:

  When you perform a debug crypto isakmp 255, so you see that the cisco vpn client does not support SHA +, you must use MD5 + AN or sha with 3DES/AES.

  Be careful, this debugging is very talkative, but that's the only way I found to get ITS proposal on debugging.

  Well, change your strategy using MD5 isakmp / OF would do the trick.

• How to use Windows 7 64-bit cisco vpn client?

  Hello

  I want to use the cisco vpn client to connect to my Institute.

  I use Windows 7 64-bit edition Home premium.

  I tried several options, but nothing has worked.

  Please suggest me the correct procedure to run on my Windows 7 64 bit Home Premium Cisco vpn client.

  Thanks in advance,

  Federico

  VPNclient is not yet supported on 64-bit windows.

  However, there is a beta version of the next 5.0.7 version that does.

  Have you tried this version? If so, what are the exact symptoms?

  Edit: you can download the 5.0.7 beta here

• What are the ports used by the Cisco VPN Client?

  Hello

  I need to open my outgoing traffic on my firewall to allow two interns (LAN) Cisco VPN Client to connect to their Internet virtual private network.

  I already opened the port 500/UDP, but they are not able to connect. If I open all outgoing ports, they can connect.

  What are the ports used by the Cisco VPN Client?

  Thank you

  You need to open:

  UDP 500

  ESP protocol

  You must also open the UDP 4500 port (if using NAT - T).

  In addition, if the clients are connecting to a VPN 3000 Concentrator series and it is configured for all other options of NAT-transparency, corresponding ports must be open. By default:

  1. If using IPSec over TCP 10000, then open TCP 10000.

  2. If using IPSec over UDP 10000, open UDP 1000.

• connect Cisco VPN client v5 to asa 5505

  I have remote vpn configuration issues between ASA5505 and Cisco VPN client v5. Successfully, I can establish a connection between the client Vpn and ASA and receive the IP address of the ASA. Statistical customer VPN windows shows that packets are sent and encrypted but none of the packages is received/decrypted.

  Cannot ping asa 5505

  Any ideas on what I missed?

  Try adding...

  ISAKMP nat-traversal crypto

  In addition, you cannot ping the inside interface of the ASA vpn without this command...

  management-access inside

  Please evaluate the useful messages.