Error on startup scan hard disk

Similar Questions

• Cannot be the SSD on Asus laptop. Error there is no HARD disk

  did I lost my ssd if I want to put it on an asus, before it was installed on a toshiba without problem, but now my asus say there is no hard drive...

  OT: ssd the misunderstood

  Hello Dannytremblay,

  This thread has been created in the forum Windows 7 security, privacy, and user accounts. the moderation of Microsoft team has moved this thread to the Windows 7 Hardware and drivers forum.

• 2000 - 2B10NR: hard disk at startup error...

  They gave me this computer from a friend to keep and fix (out of warranty) and I turned on, I get the message

  Hard drive error
  Run the hard drive Test in the diagnostic system.
  Hard disk # (XXX)

  I searched your forums and thought it is better to buy recovery disks. Yes, I did.

  They came and I installed everything and became happy and then at the end (2 hours), the Recovery Manager said he failed and gave a system error log. I recorded it on my usb key. Then tried again. No luck...

  I did a test lying on the hard drive and the first time he says failure of long DST: 6BS883 - 6 B 7806-MFGK1F-61? ED03

  So I need to know if it's a simple hard drive failure.

  Everything came out OK in tests.

  I found that a replacement HARD drive on ebay for $ 30 and it's an easy replacement procedure.

  I just need a confirmation of this is the failure of HARD drive before you buy

  What HARD drive I see for my model:

  320GB SATA drive hard - 5 400 rpm, 2.5-inch small form factor (SFF)

  Is this correct? There is no model custum. Bought at the store with equipment and factory settings.

  Thank you

  Yes, DST Fail means that the hard drive is bad. The 320GB hard drive matches what you have now.

• T1200XE error fall on hard disk 0 initialization

  Hello!

  I just bought an older T1200XE. When I start the laptop, it prints the message "error initializing hard disk 0" after the memory test, (a few seconds). I have to start with a floppy disk BACK.

  If I run FDISK, after awhile, it says 'Disc read error fixed', but if I run FDISK/status it shows me the disk of 20 MB. I downloaded FreeDOS and the FDISK, including in this OS says "controller error".

  I have an another T1200XE and this is exactly the same!
  I can't believe that two controllers or hd is dead!

  It may be possible that the free battery CMOS have erased the BIOS, but, how can I access the BIOS and configure the 20 MB HD? any idea? The setup1.exe program do not have a HD section...

  Help please!

  Thank you to.

  Hello

  Press F1 at startup to enter the Bios.

  http://FTP.Toshiba.ca/support/TechSupport/TSBs/all/-TSB000733.htm

• Qosmio F20 - integrated HARD disk error

  My F29 took a very heavy today around the area of the HARD drive on the right forward, while my children played. Basically, I'm saying that when it hit it eclipsed the panal speaker close to the screen.

  For some time he continued to work but about 10 minutes later I got a blue screen with a load of text and then it is just rebooted.

  During the startup of the screen, an error come saying 'built-in HARD drive error... Now, I checked the connection, and they seem pretty solid. can I do to get my system working again?

  Thanks in advance
  J

  Hello

  Your HARD drive is perhaps a pity
  Can you see that the drive listed in the BIOS?
  Are you able to reinstall the OS?

  You should first check this.
  You could also test the HARD drive by using the drive fitness test tool:
  http://www.HitachiGST.com/HDD/support/download.htm

  This will check the disk on some points.

  But if the HARD disk is damage need you a new!

• Satellite M40 does not start from hard disk - read error

  "I push the button - briefly see the In Touch with tomorrow TOSHIBA screen - then ' + a disk read error occurred press Ctrl Alt Del to restart +".

  I control alt delete brings me briefly on the screen TOSHIBA where I can choose either F2 or F12.

  Do I need a startup disk and where can I get one in order to boot from the CD ROM?
  Do I try to get into the Satellite M40 product Recovery DVD-ROM - this concern for me as the hard drive will be reformatted and all data will be lost.

  I'm stuck please help!

  Hello!

  If you enter the product recovery disc, Windows will be relocated and will be erasing all data on the HARD drive.

  I think that your HARD drive is damaged. You can check this with the Drive Fitness Test. Here you can download:
  http://www.HitachiGST.com/HDD/support/download.htm#DFT
  Download the CD image, burn it to a CD and boot from it. Then you can test the HARD drive.
  On the same site is a user's guide if you want to know more.

  By the way: you can save the data on the HARD drive, when you put it in a box external HARD disk. Then you can save the data on another PC, if the HARD drive is ok and have no errors.

  Good bye

• SMART hard disk error after replacing HD

  Hello!

  I SO hope that this someboidy is able to help me.

  I'm NOT a novice but I am confused.

  I replaced with the same model HD HD CQ58 provided with COMPAQ because the old HD was shot - how it happened escapes me.

  Anyhoo, after screwing a new HD I wanted to put OS on it, but I get the following error just after pressing set button / stop:

  SMART disk error

  INTELLIGENT drive control has detected an imminent failure. So no los data, please backup the content immediately and run the system diagnostics hard drive.

  Hard drive 1 (301)

  F2 System Diagnostics

  ENTER - Continues start

  For more information, please visit: www.hp.com/go/techcenter/startup

  I will return the LINK later.

  First of all, I pushed ENTER. What has emerged is:

  Not found boot device

  Please install an operating system on your hard drive

  Hard drive (3FO)

  F2 System Diagnostics

  For more information, please visit: www.hp.com/go/techcenter/startup

  I pressed F2 and this is what happens:

  I get the diagnostics Menu.

  Version 1.6.0.0 - BIOS

  For more information, please visit: www.hp.com/go/techcenter/PCDiags

  Memory test

  Check the hard disk

  Language

  Output

  I pressed Hard Drive Test is the "Quick Check" and that is the message I get:

  INTELLIGENT control: NOT AVAILABLE

  DST short: NOT AVAILABLE

  ==============================

  For more information, please visit: www.hp.com/go/techcenter/PCDiags

  I tried the LINK, it does not exist.

  I also went in the Boot Options in the BIOS to boot from a USB and put the USB HD in the first place.

  When I restart it does not recognize a USB key. I tried Windows 8 and UBUNTU which ususally works on all the machines I've fixed so far.

  No chance whatsoever.

  As I mentioned earlier:

  I'm puzzled.

  I have no recovery CD and cannot make one because I'm not running Win8 on any of my PC.

  Thus, any suggestions?

  Help, please

  Thanks in advance

  Henry of Kai

  First of all:

  Thank you all very much for taking the time and you answer!

  And now, for what happened after I did all what has been proposed:

  Nothing.

  The message remained the same.

  Still no hard drive (even if it was new)

  Then I took a hard drive to work with Win7 on it from another machine, put it in the Compaq and... nothing.

  I tried the USB with Win8 (NTFS with Rufus) does not.

  I don't know why, I tried again, but when I used the same USB with UBUNTU Live - 14.04. on that I had taken or tried before... He recognized at startup.

  Weird hard drive wiped completely since it was not recognized by the BIOS (one with Win7 on it... data paths but I had backup ).

  So, now I'm running the faithful Tahr on the Compaq and it works fine.

  I will try to put the original Win8 on it, but the system doesn't seem like more since USB NTFS NTFS are not recongised at startup.

  Well Anyhoo, I got the machine to work.

  Would have been nice to know what was wrong with him to solve future problems, but at least I had to register in this forum

  So I could bore you guys with questions in the future.

  Take care

  Kai

• My computer won't allow me to access my files on my portable hard disk without error appear "you must format the E: drive before using it. How can I fix this please!

  My computer won't allow me to access my files on my portable hard disk without error appear "you must format the E: drive before using it. How can I fix this please!

  Try to scan your driver with anti-virus, also try to throw the disc looking for this driver and as you try to run the following tools:

  http://support.Microsoft.com/mats/system_maintenance_for_windows/

  http://support.Microsoft.com/mats/windows_file_and_folder_diag/

• Try to add a printer, get the 0x000003e7 error code, event log indicates block defective hard disk.

  Original title: try to add a printer, get error code OxOOOOO3e7, event log indicates block defective hard disk.

  I have tried disk cleaner, no help

  Hi 2012mike,

  (1) what is the number of brand and model of your printer?

  (2) what has been the result of chkdsk?

  It is sufficient to indicate the complete error message you receive.

  Please provide the details of the event logs.

  Method 1: Run the fixit available in ink below

  Problems printing and printing errors

  http://support.Microsoft.com/mats/printing_problems/en-us?EntryPoint=lightbox

  Method 2: Clean boot the computer and then try to install the printer

  Follow step 1 in the link below,
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  Important: n ' forget not to put the computer to a normal startup follow step 7 in the link.

  Thanks and greetings

  Ajay K

  Microsoft Answers Support Engineer
  ***************************************************************************
  Visit our Microsoft answers feedback Forum and let us know what you think.

• G8 Pavilion laptop hardware error - new hard disk?

  Hello, I spoke with a representative from HP and I wanted a second opinion. Here are the facts:

  Possible virus causing the model to be very slow and have errors at the start up.

  Problems of gel even in "safe mode".

  Decided to do a "System Restore" using F8. Follow-up of the steps, took 20 + minutes, FINISHED.

  A screen says that I can, "1. update of security for HP and microsoft;   2 re - install any other software;    3. install all the backed up files. I selected 'NEXT' at the bottom of the screen, then, "OPERATING SYSTEM not FOUND '. Now I can't other than 'F' screens anyhere

  I call HP. A rep tells me to use F2, test drive. On a quick scan, 1 hard disk failure (SMART disc is OK). The full scan, 1 hard disk failure (SMART disc is OK).  The representative asked me a long code determine the failures, and there is NOT.  I go out of the main system diagnostics page and there are two failure codes: 303 (quick scan) and 305 (full scan). The rep wants codes any longer, but there is not.

  My question: do I need a new hard drive, or I can just recovery disks?

  Thanks for any help you can provide!   -Sarah

  Hello

  Longer code (up to 24 characters) means that the HARD disk is dead. 305 error would indicate that your hard drive is defective and must be replaced. Please backup your files/data as soon as possible. Is your machine still under warranty? In the affirmative, please call HP for a replacement.

  Update: Sorry, I'm a little slow - 3rd opinion then.

  Kind regards.

• Windows hard disk error message

  I just got a strange error message that popped up while I was surfing around Facebook.  Before you do anything, I want to be sure that it is legitimate and not somebody trying to make me install a virus or something like that.  And if it is legitimate, I want to know what I would do to this topic.

  The error message says:

  "Windows has detected a hard disk problem.

  Back up your files immediately to prevent loss of information, and then ask the computer manufacturer to determine if you need to repair or replace the disk. »

  Then it gives me two options:

  "Start the backup process."

  "Ask me later".

  If the drive fails before the following caveat, you may lose all the programs and documents on the disk. »

  So, if I click on the button "Show invisible characters", he says:

  "For immediate action."

  Because a disk failure will make you lose all programs, files and documents on the disk, you should back up your important information immediately.  Try not to use your computer until you have repaired or replaced the hard drive.

  Which drive is a failure?

  The following hard disks are fault condition:

  Name of the disk: Seagate FreeAgent XTreme

  Volume: I:\ »

  I am running Windows Vista 64-bit and the hard drive in question is a disk Seagate external, as indicated by the error message.  Also I screenshotted the message box if this description was not good enough.

  Hello

  Disk problems can take seriously very quickly so I carefully check the disc now and do not forget
  to keep redundant backups of your important data (use several methods).

  Inside the Windows - Regular or Safe Mode (repeatedly press F8 as you start).

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  GOLD:

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ----------------------------------------------------

  For even better and more efficient to check:

  At the Recovery Console prompt (if you have one) or a Vista/Windows
  disc 7 - If you do not have a Vista/Windows 7 disk you can borrow a friend (it must be the same
  32 or 64 bits and they are not protected against copying) or make a. Also your system manufacturer will sell the
  physical disks cheap since you already own windows.

  Chkdsk /f /r

  RESET

  After k and before space / f and before.

  sfc/scannow

  RESET

  Space after c and before.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  What are the system recovery options in Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  ----------------------------------------------------------------

  Go to settings/settings F2 (BIOS/CMOS) often as you start so watch the screen as you start. Define the
  Start the command of CD/DVD disks of Windows (Vista or Windows 7 If you have installed.)
  Be sure to set in when.

  If you need to repair disks - these help repair Windows not re-install.

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  =====================================

  If CheckDisk is unable to fill as above:

  (The old 302602 links isn't now valid for Diagnostics links).

  Manufacturer diagnostic utilities - run one to your hard drive
  http://www.techsupportforum.com/hardware-support/hard-drive-support/462298-no-IDE-device-found.html

  Corrected list dated 06/09/2010

  Fujitsu hard drives: utility of diagnosis here
  http://www.Fujitsu.com/EMEA/products/HDD/

  Hitachi hard drives: utility of diagnosis here
  http://www.HitachiGST.com/support/downloads/

  IBM hard drives: use Hitachi utility *.

  Toshiba hard drives: use Hitachi or Maxtor utilities

  Maxtor hard drives: Diagnostic Utilities here (now SeaGate)
  http://www.Seagate.com/www/en-us/support/

  Quantum hard drives: use the Maxtor utilities

  Seagate hard drives: here Diagnostic utilities
  http://www.Seagate.com/www/en-us/support/downloads

  Conner hard drives: use the Seagate utilities

  Hard drives Samsung: utility of diagnosis here
  http://www.Samsung.com/global/business/HDD/

  Hard drives Western Digital: utility of diagnosis here
  http://support.wdc.com/product/download.asp?lang=en
  Trial versions of one of these 'might' help.

  SpeedFan
  http://www.almico.com/sfdownload.php

  HD Tune
  http://www.hdtune.com/

  I hope this helps and happy holidays!

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Windows 7 Pro repairs hard disk errors

  My hard drive had errors and corrupt sectors.  I ran the tool to fix my hard drive and now need to repair the operating system.  I am running windows 7 pro legal copy of course as always.  What is the best way to repair windows 7 without having to redo my computer everything and start again.  I know that there are some missing files due to hard disk errors because strange things are happening now and some things do not work properly.

  E-mail address is removed from the privacy *.

  Trevor Walsh

  Try to repair the Installation of Windows 7

  1. Insert the DVD of Windows 7 and restart your computer
  2 boot from the DVD.
  3. choose your language and click Next.
  4. click on repair your computer, select the operating system you want to repair.
  5. click on the link to repair list system in the System Recovery Options recovery tools.

  More information and a how to guide:
  http://pcsupport.about.com/od/toolsofthetrade/SS/Windows-7-startup-repair.htm

  If this does not solve it:

  1. Insert the DVD of Windows 7 and restart your computer
  2 boot from the DVD. If you are prompted, press any key to start Windows from the installation disc.
  3. choose your language and click Next.
  4. click on repair your computer, select the operating system you want to repair.
  5. Select command prompt and try the following commands (one command might work, or you may need to use several commands according to the exact problem):
   
  Bootrec /fixMBR
  Bootrec /fixBoot
  Bootrec /rebuildBCD

  Note: there is a space before the /.

  Questions about installing Windows 7?
  FAQ - Frequently Asked Questions from Installation Windows 7 & responses

• Smart hard disk error: "Press enter to continue and it starts OK.

  I have run chkdsk full and sometimes without error, but at startup it says Smart hard disk error. Press ENTER to continue and it starts OK

  Go into the BIOS and run the drive Diagnostics (long version).

  Normally, when you get a SMART disk error this means imminent disk failure.  Smart drive test checks the environment of hard disk and is much more than chkdsk thorugh.

  A cautious soul would replace the disc if the diagnostic test is a failure.

  Is your laptop still under warranty?

  Best regards
  ERICO

• Unable to overcome error - "the startup disk cannot be partitioned or restored to a single partition.

  Hello!

  I'm trying to install Windows on my iMac (late 2013, running 10.11.6) without success.  I created the ISO to a flash drive, but when I try to use the Assistant Boot camp, I am referred to the following screen:

  

  I did my best to study solutions. The cause, by apple support discussions, is that there is another partition of pre-empting (stop) the wizard boot camp partitioning the hard drive.  I studied the partitions on my HDD after unplugging all devices and found this:

  

  This shows the main partition: Macintosh HD, the bootcamp partition: BOOTCAMP; and 2 unknown partitions: "Apple HDD ST100DM003 Media" and the same * M004.  I was able to delete the first Apple ST100DM003 HARD disk partition and ran first aid on the fusion drive after that the second he would not remove.  Also, I can't delete the boot camp partition.  I keep getting the same message when I try to install windows on a partition of the fuser unit using Boot Camp Assistant - "Startup disk cannot be partitioned or restored to a single partition".

  Any suggestions?

  Please after the release of the following OSX Terminal commands.

  diskutil list

  Cs diskutil list

  A reader of merger should have underlying EFI, OSX, Recovery HD on each of the physical disks. If your previous Windows installation attempts have failed, the disks can leave in a State where BCA use/will not change them.

• SMART hard disk error (301)

  I WANT m6-1120sw my friend. When I turn it on it shows SMART drive hard error, said diagnosis: "SMART Check: NOT AVAILABLE, short DST: caution. His old HDD, I replaced it with a new one, but nothing has changed. -What would be a problem with the SATA controller on the motherboard or is it something different?

  Hello
  
  Smart disk error indicates failure of hard drive. You still get any ID failure?
  
  Since you have already replaced it & not showing is not available, the probability is for the connection by defective SATA cable or SATA controllers or motherboard itself.
  What of all the other disk hard test - wide?
  
  Try HD Tune Pro software currently running on the system.
  
  You may have to contact HP for repair.
  
  Thank you