Error PCI / USB - W2003 Server - Dell POWERVAULT NF100

Similar Questions

• Dell PowerVault MD3600i validation error - unable to update firmware - Data:

  Hello

  I have the following problem when trying to upgrade the firmware version of 07.84.44.60 to 07.84.47.60 on my Dell PowerVault MD3600i.

  Assistant firmware upgrade RAID controller module reports the following error

  • Data validation error: the storage Bay cannot be updated one or more host entries in the Module of the RAID 0 controller did not match those of the RAID 1 Controller Module. To resolve this issue, contact a technical support representative.

  Can not find any similar problem on the net, if anyone here can help me please

  There are a few things you can try. If you have configured multiple paths you can remove one of the controllers, wait 5 minutes and then put it back and try to do the update. Or you can try to clear the log of events and then update the Firmware.

  Let me know how it goes and if you have any questions or concerns.

• Is it possible to connect two DELL PowerVault MD3200 single PowerEdge R610 Rack Server

  We have the SQL cluster with two nodes (the two PowerEdge R610 Rack Server) connected to the DELL PowerVault MD3200. As we are short on space, the idea came to add additional DELL PowerVault MD3200 to the cluster. Is this possible?

  Hello, IPM.

  Yes, you can add an another MD3200 to your R610 server & get both to work.  As you run lack of space, you can also simply add a MD1200 if just needing space as the MD1200 is cheaper than a MD3200.  The MD1200 will connect via your MD3200 sas & can provide you with the additional disk space if that's what you're looking for.

  Please let us know if you have any other questions.

• Different segment of the USB network server error

  Running Windows Home 7, with a wired USB (SOHO) server when connected, he says 'Different Segment of USB network server' how can I solve this problem?

  Concerning

  Hi David,

  Thanks for the update on the issue.

  If the problem persists, try these methods below and see if that solved the problem.

  Method 1:

  There may be several reasons why a computer is not able to detect a signal wireless adapter. Wireless networks appear only if your PC has a wireless network card installed, the adapter is turned on and the wireless access point is within reach. Many network connection problems are caused by hardware that is not configured or the drivers are not installed properly. Follow the steps described in the article below to check on all aspects and troubleshoot accordingly.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:

  If you cannot connect to a network, it could be a problem with your network adapter. You can try to use the network adapter troubleshooting utility to automatically find and fix some common problems.

  How can I troubleshoot network card?

  http://Windows.Microsoft.com/en-us/Windows7/how-do-I-fix-network-adapter-problems

  Keep us.

  Kind regards

• Dischetto pilot controllo Sata Powervault NF100 [MS]

  Salvo..., x motivi di perdita file, dobbiamo reinstallare he operating system

  Windows storage server 2003 r2 x 64, sul powervault NF100 con con controller raid due hd sata...

  Durante sommergibili del only operating system F6 x creare i personal raid, disk x raid driver controllo, disco for mi asks he dove posso scaricarli?

  Grazie

  Salve,

  dopo aver premuto S e caricato pilot del sas5 prema per, alla schermata buttons it system information:

  the installer will take care for the mass following storage device:

  con indicated it modello di controller

  to basso sulla legenda e indicated:

  Additional feature S specify - ENTER continue - out F3

  quindi prema ENTER per andare avanti.

  Speaking saluti

  Manual

• iSCSI and Fibre Channel on the Dell PowerVault MD3000 SAN shaerd with 2 physical servers

  Hi all

  I'm doing new virtualization technologies work in my office for assistance:

  2 x Dell PowerEDGE 2950 III each installed with iSCSI next accessing the SAN controller

  1 x Dell PowerVault MD3000 (10 x 300 GB 15 k rpm SAS)

  The

  VMWare ESXi is installed in an internal USB to load 4 x virtual machines which is

  under SOLARIS (using project, houses, SAMBA file server and)

  Source code repository and compile the source code of the project Build

  Server too.)

  5 x Windows Server 2003 which perform as Apache Tomcat application server.

  And

  I wonder if it has performance benefits in the application of the

  Shared SAN for these two physical server via iSCSI in contrast with

  Fiber Channel.

  I am aware that CF is faster and more expensive, but in this case, I won t run a VM with DB server on it.

  must

  I enter the path to have iSCSI or stick with the given FC

  the SAN runs on 15 k rpm SAS used by 2 ESXi server.

  Please let us know of a reflection regarding this configuration.

  Thank you

  Usually, you take NIC 1 gb connections available on your host and configure them as such.

  2 network cards go to the San, most of the time that it is actually two networks with different subnets.

  1 network card next LAN

  1 network card for the management

  We only use three network cards currently on our guests, 2 for San and the other for management and lan. We use two switches dedicated to dedicated networks dual iSCSI san. This allows to easily add additional hosts in the future.

  You get to decide a bit, but the double san network is pretty much a given. You can do all this of course with the VLANs as well. We use the switches unmanaged yet in our Organization.

  PS: Passing path recommended is to have completely isolated storage of the LAN network / network of the user.

• PCI USB 3.0 Express card does not work

  Discription of the system:

  • HP Pavilion Elite HPE-520nl desktop PC
  • Processor Intel Core i7 - 2600
  • Memory 6 GB
  • Windows 7 Ultimate 64 bit
  • Service Pack 1
  • The map of USB 3.0 pci card the "HP-lable" is printed. Therefore an alaaa by HP original card.

  My HD portabale with USB3.0 interface is not recognized. Also all USB 2.0 memory sticks are NOT regonised by this card pci of USB 3.0.

  I searched on the web, this forum ect. and posible all software and drivers updated.

  Now at least there's no sign of escalmation in the Windows Device Manager.

  There are no errors in Windows and by double clicking on each and evry device a puppy window says: "device is functioning! (But when I put in a usb in the port USB3 device, nothing happens, not even a new drive appears under 'Computer'.)

  OK maybe the card is the default, so I bought at a local PC store a new one (Konig CMP-PCIE2USB3), but same problem.

  Well maybe the PCI slot is the problem... I put the card HP in the free location. But still no luck.

  Now I have 2 PCI USB 3.0 Express card in my office, but no USB 3.0 for my USB 3.0 devices connection.

  All USB 2.0 ports are working well.

  Help, please.

  

  I uninstall the original card and don't forget to remove the driver. Then install the Konig CMP-PCIE2USB3 and install the driver from the Web site. Don't forget to attach the molex 4 pin of your power supply.

• Incompatibility of Configuration Dell PowerVault 220 s

  Recently, I experienced a power failure on a Dell PowerVault 775N server, which connected a PowerVault 220 s storage device. Once the power has been restored and restarted the server, I get a beep and an indication on the server there is a «Configuration of drives and the NVRAM shift (normal shift)»

  We suspect that the controller card may be bad.  Anyone could help the who may have a similar problem before the experiment and give directions with the resolution of this problem?

  What's still recoverable data?

  Thank you.

  Difference between in the PERC configuration and the configuration on the hard drives, a message is displayed at startup upward:

  "Configuration of the incompatibility of drives and the NVRAM. Run view/add configuration from the Configuration utility option. Press a button to run the Configuration utility. »

  The configuration of RAID arrays is stored in two places: the nonvolatile RAM (NVRAM) of the RAID controller and the hard disk. Following a power failure or configuration change, the configuration in NVRAM now differs from that on the hard drive. Perform the following steps to resolve the issue.

  Note: If at any time you are prompted to initialize the table, do not. Initialization destroys all data on the logical drive. During the initialization process, all data bits are changed to zero.

  1. Press any key to enter the Configuration utility.

  2. in the management Menu, select Configure.

  3. Select view/add Configuration.

  4. two options are present: view disk Configuration and NVRAM Configuration of display. Because the original configuration is stored on the hard disk, select the Disk Configuration view.

  5. check that the correct configuration for the RAID array is now displayed.

  6. press the ESC key. When you are prompted to save the configuration, select Yes.

  7. the configuration is stored in NVRAM on the RAID controller and matches the configuration on the hard disk. When you are prompted, press a key to continue.

  8. press ESC until you are asked to leave. Click Yes to exit.

  9. press on CTRL + ALT + DELETE to restart the computer. The server should now start normally.

  A note more:

  If you don't see not an overview of NVRAM, see option records, trying to erase the configuration...

  Unplug and power off of the PV220. Restart the PERC BIOS, make sure you're on the PERC external and clear configuration. Connect up to 220, power and restart the server, you should now get another set-match and should display disks.

• BlackBerry smartphone Error Message "USB device not recognized"

  I have a BB Curve 8320 on Orange UK.  When I connect my device or my work PC (Dell laptop Windows XP SP3) or my PC at home (Sony Vaio Vista SP1) shows the error message "" USB device"unrecognized and say that the USB device has malfunctioned?  It seems to work very well in outside it and connected to the PC fine until ten days ago.  I tried to reinstall the Desktop Manager software (and updated) and I conducted several soft resets on my device; nothing seems to work?

  Can anyone help please?

  on the laptop, make sure that the power cord is plugged directly into the PC and try a USB port at the back (without stand) if that is not working, call your carrier, it looks like you need a replacememnt

• Error 0701: USB over current on HC/Port - Bus: 00 H Dev: 1DH Fun: 01 H / Port: 00 H

  I have been using the laptop without any problem until I encountered ERROR as follows: AArrgg! @#$

  ************************************************

  Error 0701: USB over current on HC/Port - Bus: 00 H Dev: 1DH Fun: 01 H / Port: 00 H
  Error 0701: USB over current on HC/Port - Bus: 00 H Dev: 1DH Fun: 02 H / Port: 00 H

  Press F1 for Setup, press F12 for Boot Device selection Menu
  **********************************************

  Well, the F1 takes me into the Bios, well all eyes. And F12 does nothing. I tried to boot from the CD drive, but of no use, I tried to solve million methods but invain I could not if anyone has a solution for this, you can provide, I will be very grateful

  Thanks in advance

  Srini

  Insert the cd of the same wait o/s until it reads "loading windows files" then here you eject the cd /dvd. This work for me.

• I received a phone call from a tech company (they said they serve Dell)

  I received a phone call from a tech company (they said they serve Dell) indicating they might say to monitor my computer someone (South Africa) shares my computer.  Is this possible?  Dell said that they do not call for clients and found that all the latest downloads on my PC.

  Wednesday, March 25, 2015 18:25:24 + 0000, Frantastic_70s wrote:

  I received a phone call from a tech company (they said they serve Dell) indicating they might say to monitor my computer someone (South Africa) shares my computer.  Is this possible?  Dell said that they do not call for clients and found that all the latest downloads on my PC.

  Almost certainly, it was a scam and with various names and phone
  numbers, one that has become very common these days. See
  http://www.troyhunt.com/2012/08/virus-scams-social-engineering-victims.html
  and
  http://www.howtogeek.com/176605/tell-your-relatives-no-Microsoft-wont-call-you-about-your-computer/
  and
  http://www.howtogeek.com/180514/the-%E2%80%9ctech-support%E2%80%9D-scammers-called-Htg-so-we-had-fun-with-them/

  In addition to their money get on your part to do anything of any value,
  If you leave them in your computer, who knows what they were doing or where
  What confidential information they stole.

  So if you have done so, I highly recommend that you do both of the following
  immediately:

  1 do a clean reinstall of Windows.

  2. after reinstallation of Windows, change all your passwords.
  especially the banks or other
  financial sites.

  Since they have perhaps installed a recorder of strikes, changing just your
  Passwords may not be good enough.

• Error in el servicio perfil del usuario al iniciar secion. No will can be charged el usuario perfil

  Necesito UN ayuda debido al iniciar Secion has no reconoce the contrasena don't y dice: error in el servicio perfil del usuario al iniciar secion. No will can be charged el usuario perfil. Por favor are urgent!

  MUCHAS gracias.

  Hello

  You created this thread in the English version of the Microsoft Community. Please could you click on the globe icon to the world at the bottom left of the screen and then choose your preferred language. Now create your thread again.

  

  If you can't find a suitable language, please go here:

  http://support.Microsoft.com/common/international.aspx

  for other international support options.

  Thank you.

• All 32-bit applications crash with error 0xc000005 after windows Server 2008 R2 backup

  Hello world...

  I am in a big mess... and really need help!

  I did last night a Backup windows... but one of my users were connected to the server works with applications...

  and this morning No 32 no bits applications... same installer...
  the 64-bit application works very well...

  Others or generating an error 0xc000005 and stop...
  failing Ole32.dll module...

  And I'm sure that the backup is reliable, even if the backup of windows said it was successful...

  I tried to restore only the apps files... but it seems more complicated than that...

  If anyone has an idea...

  Hi, Emeric,.

  Thanks for posting the question on Microsoft Community.

  According to the description, it seems that 32-bit applications crash with an 0xc000005 error code in Windows Server 2008.

  As the question more appropriate forums Technet, write the topic in this forum for better support.

  http://social.technet.Microsoft.com/forums/en-us/WindowsBackup/threads

  Using the windows-related issues feel free to post on Microsoft Community.

• trying to browse some of the sites locally that we get the following error: HTTP error 500.19 - Internal Server Error

  HTTP 500.19 - internal error in the server error

  Hello

  We have Windows 2008 R2 Server, 64-Bit

  IIS version: 7.5.7600.16385

  We had several Web sites for our clients on this IIS server.

  While some of the hosted site work properly, but when you try to browse some of the sites locally, we get the following error:

  HTTP 500.19 error - internal error the requested page server is inaccessible because the configuration data of the page are not valid.

  Hello SGTPrasad

  You can find the Server forums on TechNet support, please create a new post at the following link:

  http://social.technet.Microsoft.com/forums/en/category/WindowsServer/

• How do I get standard enhanced pci-usb host controller. My pc says that I could speed up usb.

  Running on Windows XP HOME SP3, with updates to date (30/08/2013). I tried in vain to find this driver so that I can use USB2. The chipset of the PCI card - USB 2 is ALi.  I tried to look at the site of ALi but in vain except re - runs to third parties that offer something other than the drivers I need.

  Someone at - it a response?
  Regards, Ray.

  Hi Nirmal 5,.

  After struggling against v. much, my EHCI USB problem seems to be resolved. I found a version a little later the EHCE Ali set of drivers and to reach all devices are woodworking!
  My system is old in terms of pc, I built it 11 years ago, and being a pensioneeeer, I'm still saving up for a new construction. The mobo had USB 1.1 embedded (which I disabled it in order to eliminate conflict, after installing PCI - USB card). After you have installed a PCI - USB card, my trouble started. Difficult to get info., gigabyte re: problems like this, so had to groping my own solutions.
  Thanks for your concern.
  Sincerely, Raymond.