Error reading rhvariable.apj after crash RH9

Similar Questions

• Error reading from disk after the installation of windows xp

  Ideas:

  • I got a new hard drive installed by professionals. I went to install Windows XP on my computer. He passed through the first stage, but after copying the files, it wouldn't restart. That repeatedly brings me to a screen that says: a disk read error occurred press Ctrl alt delete to restart and then it looks like it will restart but hten goees return the same screen. How can it be a disk error if it is passed by the installer and I've never touched the disc later? Now, I can't do anything with it. Any help would be greatly appreciated.

  Do not install an operating system is usually caused by (in order of probability):

  1. you are trying to install with other devices connected to the computer. Unplug them before trying to make an installation.

  2. "" "" defective installation media. "" Check the CD/DVD installation for scratches, tasks. Try another machine.

  3. bad optical drive. Test with another CD/DVD bootable or Exchange for a well-known work.

  4. faulty RAM. Test with Memtest86 + www.memtest.org . You will download the .iso image file to create a bootable cd. Burn the file with the third party burning software *-as an image, not in the form of data. Then start with the media that you did (you may need to change the boot priority in your BIOS so that the optical drive is the first boot device). The test runs immediately. The test run for an hour or two--at least that errors are seen immediately. If you get any errors, replace the RAM.

  A good free choice ImgBurn comes from www.imgburn.com .

  5. bad hard drive. Test with a diagnostic utility downloaded from site of the disc mftr... You create a bootable CD with the files you download. Burn the file with a third-party burning software - image, not in the form of data. Boot with the CD that you have done and do a full test of the reader. The physical tests fail, replace it.

  (Note: since you just replaced your hard drive is probably not the cause.) However, you should always test because it is not uncommon that new hard drives to the failure of the box.)

  6. other hardware components are faulty. MS - MVP - Elephant Boy computers - don't panic!

• Upgrade RH 8.02 to RH9.02 rhvariable.apj file read errors

  We have recently upgraded from RH8.02 to RH9.02.  When I open my project RH8 RH9 he obviously wants to spend so I say OK.  In seconds, it errors saying something to the effect, error reading rhvariable.apj.

  Initially, the project was under version control, so I thought that maybe that was the problem so I reinstalled RH8 and did two upgrades to 8.02.  Deleted my version control project to a local folder.  My old project opens and works perfectly with RH8.  All my variables of ~ 1000 are there.  So I deleted the .cpd file and tried to upgrade/convert the local copy to RH9.  The converted version of RH9 has ZERO variables and gave the same mistake of not being able to read the file rhvariable.apj.  I don't want to redo a thousand variables, then place them in all subjects.  It's a manual parts and variables are in every sense, it would be more painful and not worth the upgrade.

  We had a lot of problems when we went from to RH8 RH7.  It would be of course if we could upgrade for once and work the software you want and simply convert the project and... work.

  So, lets see, I looked at the file rhvariable and it is clean.  He had a few little things that seemed suspicious so I removed and checked everything was ok in version 8 and everything was fine.  A running RH9 conversion and cannot read the file rhvariable.

  Deleted the infamous .cpd file unchanged, still does not.  So I have a working version of RH8.02 and a non-functional version of 9,02 a variable angle.

  We have also recently updated our main project which at the same time, the project was in and these variables came in fine.  Just switch to the HTML view in order to save anything in our main project.  Nothing saves the Design view and I open a discussion into Version control for this.  That project is under version control and for the moment we have a work around, but it would be nice if we could just hit Save button and save the topic without having to edit HTML mode to save.  Very strange.

  Thus, Peter... and al, you have any ideas why my variables are not read by HR 9.02 HTML?  We thought the appeal for support from Adobe, but they were entirely less useful in the past, so we come here first.  Thanks much for helping us to get version 8 to work 2 years ago.

  DV

  Peter,

  After you have reinstalled RH8, I could open and out of control RH8 Version 3.1.  Now with the local telephone to my pc, it worked well in RH8 but failed in RH9.  So I carefully inspected the rhvariable.apj file and found a few lines that were not like the others.

  14 - x 100 - XT

  3010107830

  01 - x 902

  < span style = "do-family: Verdana, without serif;" do-size: 10pt; "> not available </span >

  I changed this line to

  14 - x 100 - XT

  3010107830

  01 - x 902

  Not available

  There are 2 or 3 other places where this has happened.  I am sure that it was the result of the application of the style of the font to the variable in RH8.  Strange lines were all lines of text where a part was no longer available or was not ready to order yet.

  After solving it, RH9 was able to open the project locally and my variables seem to be ok.  I have to check spot numbers, but I think this information from the police in the variable line is what was confusing RH9.

  There was another line that had this:

  01-014

  & #160;

  which I changed to:

  01-014

  Vacuum

  This way I can search on empty ot see if it appears in my project and set the variable if necessary.

  For now, this seems to have solved the problem with this project.

  Please take a look at my other problem to Source code control.  We cannot save our subjects in the main project using the design mode, but if we move in HTML mode, it allows to save instantly.  We can work with that for now, but of course, it's strange.  It's a big project, 125 MB update so not something that fits in an e-mail.

  Thanks for responding.

  DV

• error code after you download security ca roadrunner (application error reads cannot read memory) and some numbers...

  error code after you download security ca roadrunner (application error reads cannot read memory) and some numbers...

  Try a system restore to a Date before the problem began:

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  See you soon.

  Mick Murphy - Microsoft partner

• Adobe reader 10 and 11 crashes after 3 to 5 sec.

  Adobe reader 10 and 11 crashes after 3-5 seconds it more recent gets fully open, it just closes. the problem is all my PDFs on my computer. and they work fine on my other labtop. tried to repair, remove, install several times

  You can try this one: go to Adobe of C:\Program 11.0\Reader (if you XI player installed), or C:\Program Files (x 86) \Adobe\Reader 11.0\Reader (XI Reader on 64-bit Windows), double-click Eula.exe, then accept the license agreement.

  Which solves the problem?

• Version control synchronizes do not rhvariable.apj and default.css

  After we had a lot of problems with the 8.0.2 update, we managed to get a compilation that was right and he takes a few weeks.  We are always having problems with the rhvariable.apj and default.css files.  We had to change the .cpd file in MS Access for our global variables from just before the update.  I didn't have to manually re-enter 800 + variables.  If my colleague is editing the rhvariable file, I can't change the file and I get an error.  If I change the file, it can not read my file.  In order to get a compilation with the variables we cut and pasted my variables in his .cpd folder and it worked, but now we are adding more variables and changing to other resulting in only one of us with a copy of work.  My system has complained the default .css that came down from the server, so I just pasted his file in my home directory and it works, but we have problems by editing this file also.  It's crazy.  The 8.0.2 really make us hurt and is still bad.  We try to run with it, but a few important issues.

  You have any ideas?

  The investigation revealed that an error was introduced in the file when it was edited manually. Adobe has fixed it so the modified file should solve the problem.

  See www.grainge.org for creating tips and RoboHelp

  Follow me @petergrainge

• Error TickTime.cpp - 290 after opening a specific project. First 2014.2 CC | Windows 8.1

  Hello

  I have the problem of this specific project on I got this errormessage:

  

  When I click on continue first 2014.2 crashes.

  I can open a version that is in a few more days but not others.

  Here's the project file:

  https://DL.dropboxusercontent.com/u/1127100/zebraworkz/KDS_company.prproj?DL=1

  I've read about similar to many problems click on the button continue, but this does not work for me. Same thing with import the project into a new project.

  here some details on my system

  

  and here which shows the eventmanager windows on error:

  Name fehlerhaften der application: Adobe first Pro.exe, Version: 8.2.0.65, Zeitstempel: 0x5486db4a

  Modules fehlerhaften name: MSVCR110.dll, Version: 11.0.51106.1, Zeitstempel: 0x5098826e

  Ausnahmecode: 0xc0000409

  Fehleroffset: 0x00000000000740c4

  The process fehlerhaften ID: 0x1f74

  Startzeit der fehlerhaften application: 0x01d023c4ae670fd0

  Der fehlerhaften application path: C:\Program Files\Adobe\Adobe Premiere Pro 2014\Adobe first Pro.exe CC

  Path of the module fehlerhaften: C:\WINDOWS\SYSTEM32\MSVCR110.dll

  Berichtskennung: 19a761d3-8fb8-11e4-bec7-d850e61edc18

  Name of the full of the fehlerhaften package:

  Anwendungs-ID, die zum fehlerhaften Paket ist relatively:

  Hope you can help me because as you know, time is money and the customer expects, and if I go back to the old version I lost a lot of work.

  Is it possible to reinstall 20141? I have already uninstalled first CC 2014 and installed again but does not help

  Graphicsdriver is the most recent.

  Thank you

  Marcus

  Please check this post: FAQ: how to fix projects that get an error "TickTime.cpp - 290" after opening a project.

  PS: Due to a large number of requests, I wasn't able to send files repaired each of you. My apologies for that! As a result, I created this post so that you can repair projects yourself.

  Thank you very much

  Regalo

• Diagnostics Windows network, the error reads 'Problem with wireless adapter or access point' and fails to solve the problem.

  «Problem with access point or wireless adapter»

  Hi, I just bought a new laptop & I have the extreme difficulty to stay connected to the internet. When I run Windows Network Diagnostics, error reads 'Problem with wireless adapter or access point' and fails to solve the problem. Help, please... Thank you, Maria

  HI Maria,

  ·         What operating system is installed on your computer?

  ·         You have installed the latest drivers for wireless network card?

  Follow the suggestions below for a possible solution:

  Method 1: Start your computer in a clean boot state in order to check if the applications of third parties or startup items is the origin of the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

   

  Note: After troubleshooting, make sure that you configure the computer to start as usual as mentioned in step 7 in the above article.

  Method 2: See these articles for solve wireless problems:

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

   

  How can I troubleshoot network card?

  http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

   

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Let us know if that helps.

• Whenever the browser opens, I get an error saying: "Explorer.exe" application crash

  Original title: I get an error saying: "Explorer.exe" application crash

  Whenever it opens explorer, I get the error below and it remains my explore

  I get the error message is the following:

  Signature of the problem:
  Problem event name: APPCRASH
  Application name: explorer.exe
  Application version: 6.0.6002.18005
  Application timestamp: 49e01da5
  Fault Module name: StackHash_b61d
  Fault Module Version: 6.0.6002.18327
  Timestamp of Module error: 4cb73436
  Exception code: c0000374
  Exception offset: 000b06fc
  OS version: 6.0.6002.2.2.0.256.1
  Locale ID: 2057
  Additional information 1: b61d
  More information 2: 167a8c47623c2496d77676b17616bd5b
  3 more information: ae0a
  Additional information 4: 8785af56cd014fa3319b3e04d072db96

  Please let me know how I can solve this problem.

  Thank you

  Sam

  Hi Sam,

  Do you remember what makes any agreement, changes this question?

  Method 1: Run the fixit available in the links below and check if that makes a difference-Worth to try
  Difficulty of broken desktop shortcuts and common system maintenance tasks

  Note: FixIt would attempt to recover bad sectors on the hard disk, in the course of this process there are chances of DATA loss from that particular area.

  Method 2: If a Protection of resources Windows (WRP) file is missing or is damaged, Windows may not behave as expected. Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps mentioned in the link below:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  Method 3:  Put the computer to boot and then check if the problem persists

  Follow step 1 in the link below,
  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

   

  If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem.

  Continue with the remaining steps to pin-point on the third party service.

  After find you the program that is causing the problem, you will have to perhaps to update or install a newer version of the program, if you rarely use that you should consider uninstalling the software.

  Important: n ' forget not to put the computer to a normal startup follow step 7 in the link.

• Error 1305: Error reading from file C:\Program Files\Microsoft Games Flight Simulator X\Scenery\World\texture\041b2su6.bmp.Verify that exists it and that you can access

  When I want to install Flight Simulator X I get the error error 1305: error reading from file C:\Program Files\Microsoft Games Flight Simulator X\Scenery\World\texture\041b2su6.bmp.Verify that exists it and that you can access how to fix?

  Hi Johannholm,

  Thanks for posting your question in the Microsoft Community. We are happy to help you.

  Go through the suggestions of this link and check if it helps you to install Flight Simulator game.

  Error message when you install a Microsoft game or a mapping program

  http://support.Microsoft.com/kb/258496

  NOTE: After you check the clean boot feature configure Windows to use a Normal startup using step 3A proposed in the above mentioned link.

  WARNING CHKDSK:

  Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  Hope it will be useful. If you still have questions, please reply and we will be happy to help you.

• ORA-12570: network Session: error reading unexpected package

  Hello

  When installing in a system we have a step to import uses managed ODP.NET package NuGet Oracles Oracle.ManagedDataAccess.12.1.022. After some repeated import the following error occurs:

  Oracle.ManagedDataAccess.Client.OracleException (0x80004005): ORA-12570: network logon: unexpected package-> OracleInternal.Network.NetworkException (0x80004005) read error: ORA-12570: network logon: package unexpected error reading-> System.Net.Sockets.SocketException (0x80004005): an operation on a socket could not be performed because the system didn't have enough memory buffer or because a queue was full

  at System.Net.Sockets.Socket.Receive (Byte [] buffer, Int32 offset, Int32, SocketFlags socketFlags size)

  to OracleInternal.Network.ReaderStream.Read (OB OraBuf)

  to OracleInternal.Network.ReaderStream.Read (OB OraBuf)

  at OracleInternal.TTC.OraBufReader.GetDataFromNetwork)

  at OracleInternal.TTC.OraBufReader.Read (Boolean bIgnoreData)

  at OracleInternal.TTC.MarshallingEngine.UnmarshalUB1 (Boolean bIgnoreData)

  to OracleInternal.TTC.TTCExecuteSql.ReceiveExecuteResponse (bands accessor [] & defineAccessors, accessor [] bindAccessors, bHasReturningParams Boolean, SQLMetaData statementType SqlStatementType & sqlMetaData, Int32 noOfRowsToFetch, Int32, Int64 noOfRowsFetchedLastTime & noOfRowsFetched, Int64 & queryId, Int32 longFetchSize, initialLOBFetchSize of Int64, Int64 [] scnFromExecution, bAllPureInputBinds, DataUnmarshaller & dataUnmarshaller, MarshalBindParameterValueHelper & marshalBindParamsHelper, Int64 [], Boolean & rowsAffectedByArrayBind, bDefineDone Boolean, Boolean & bMoreThanOneRowAffectedByDmlWithRetClause, list 1 & implicitRSList, Boolean bLOBArrayFetchRequired)

  at Oracle.ManagedDataAccess.Client.OracleException.HandleError (OracleTraceLevel level, OracleTraceTag tag, Exception ex)

  to OracleInternal.TTC.TTCExecuteSql.ReceiveExecuteResponse (bands accessor [] & defineAccessors, accessor [] bindAccessors, bHasReturningParams Boolean, SQLMetaData statementType SqlStatementType & sqlMetaData, Int32 noOfRowsToFetch, Int32, Int64 noOfRowsFetchedLastTime & noOfRowsFetched, Int64 & queryId, Int32 longFetchSize, initialLOBFetchSize of Int64, Int64 [] scnFromExecution, bAllPureInputBinds, DataUnmarshaller & dataUnmarshaller, MarshalBindParameterValueHelper & marshalBindParamsHelper, Int64 [], Boolean & rowsAffectedByArrayBind, bDefineDone Boolean, Boolean & bMoreThanOneRowAffectedByDmlWithRetClause, list 1 & implicitRSList, Boolean bLOBArrayFetchRequired)

  at OracleInternal.ServiceObjects.OracleCommandImpl.ExecuteNonQuery (String queryString, OracleParameterCollection paramColl, CommandType commandType, OracleConnectionImpl connectionImpl, longFetchSize of Int32, Int64 clientInitialLOBFS, OracleDependencyImpl orclDependencyImpl, Int64 [] scnFromExecution, OracleParameterCollection & bindByPositionParamColl, Boolean bBindParamPresent, OracleException & exceptionForArrayBindDML, Boolean isFromEF)

  at Oracle.ManagedDataAccess.Client.OracleCommand.ExecuteNonQuery)

  xxx. BatchExecuteObjectValuesContent (xr XmlReader, String sql, Int32 objectValueIdColumnIndex, Int32 languageIdColumnIndex, Int32 fieldIdColumnIndex)

  I looked for some sort of work autour or bug but found nothing. This error does not appear always, most of the machines appear quite able to complete import together without fault.

  The BatchExecuteObjectValuesContent() method uses ArrayBind to create multiple entries to insert quickly.

  Anyone have experience with? Is it a bug or there at - it a setting that I need to adjust?

  Thanks in advance!

  / Nicklas

  The two likely culprits of this error are to run out of memory or port of exhaustion. Or the other of them occur at the time that the error occurs?

• Error reading from file: state .tgz-3.

  I'm under ESXi v3, but I couldn't find anything except 4 or 5 on the forums. in any case, I am very new to VMWare and this configuration inherited from my predecessor. Today, we had to stop everything for some work on our electrical systems. I stop the VM machine and then put the host in maintenance mode. After that, we did a clean power down. From switching back on, I get the following error:

  Error reading from file: state .tgz-3.

  Help, please. It comes to our business files server which is completely offline now.

  You see your data warehouse? If so, consult and find the folder of the virtual machine and then make a right click the .vmx for comments and add to the inventory.

• ESXi v3.5 - PANIC: error reading from file: state .tgz-5

  Hello.

  Recently, suffered a power outage that caused a stop.  After the reboot, I get the following error:

  PANIC: Error reading from file: state .tgz-5

  As it is a recent construction, I did have the chance to perform a backup, a restore is not possible.  Run a repair had no effect.  Is there anything else I can do to get it back?

  Thanks in advance.

  CJ.

  try running this command in ESX console #fdisk-l and check if there is any partition VMFS (fb) detected.

  

• I get an error message on itunes app crash coreaudiotollboc.dll How can I solve this

  I get an error message on itunes app crash coreaudiotollboc.dll How can I solve this

  These errors can usually be fixed by removing the offending dll, then fix the component it is programs and features Control Panel. CoreAudioToolbox.dll belongs to Apple Application Support and are normally in

  • C:\Program Files\Fichiers Files\Apple\Apple Application Support or
  • C:\Program Files (x 86) \Common Files\Apple\Apple Application Support

  where the name of the Program Files folder may vary depending on the region.

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach. Review other cases and a list of documents to support further down the page, in which case one of them applies.

  More information area has direct links with the current and recent if you have problems to download, need to revert to a previous version or try the version iTunes for Windows (64-bit-for old video cards) as a workaround for the problems of performance or compatibility with third-party software.

  Your library must be affected by these measures, but it is also related to backup and recovery advice if necessary.

  TT2

• Sync error, incorrectly configured server after the installation of Update 7.0.1

  Since the update of Firefox (I have a Mac OS 10.6.9 on SnowLepard) by installing the Firefox 7.0.1 update, now on every page I get the Sync error message at the bottom line. Incorrectly configured server.

  Synchronization error message constantly displayed after updating to Firefox 7.0.1

  There is currently a problem with the Firefox Sync server, and the developers are working to fix it. See http://status.mozilla.com/ for updates.