Error recognition USB on XP SP3
This may be identical or similar because of ManOMullet.
Whenever I connect my new Sansa Clip + to my XP V2002 SP3 with all the latest Microsoft, the system refuses to connect it up as a USB device. Setup-> system-> hardware-> Device Manager displays the USB port with the message: "this device cannot start: Code 10." I took the advice of troubleshooting and uninstalled the USB port. I plug in, it is under the new hardware, munges for a while and then tells me that there is a problem during the installation of the equipment. The device manage returns the same message: "this device cannot start: Code 10."
However, when I have it join a XP older than SP2 competition, the device attaches immediately and works perfectly.
I'm limping this second computer loading, but I need to be able to fix the Sansa to the computer because it is one that is connected to the Internet.
After a Google search for "sansa clip + driver XP ', I found:
http://www.FixYa.com/support/t256468-computer_doesnt_recognize_mp3_player
One of the suggestions was to install the Media Player version 11. I wasn't going to, but... I did and now the Sansa Clip + Monte!
Let's say it's resolved.
Tags: SanDisk Sansa
Similar Questions
-
BlackBerry smartphone Error Message "USB device not recognized"
I have a BB Curve 8320 on Orange UK. When I connect my device or my work PC (Dell laptop Windows XP SP3) or my PC at home (Sony Vaio Vista SP1) shows the error message "" USB device"unrecognized and say that the USB device has malfunctioned? It seems to work very well in outside it and connected to the PC fine until ten days ago. I tried to reinstall the Desktop Manager software (and updated) and I conducted several soft resets on my device; nothing seems to work?
Can anyone help please?
on the laptop, make sure that the power cord is plugged directly into the PC and try a USB port at the back (without stand) if that is not working, call your carrier, it looks like you need a replacememnt
-
I have been using the laptop without any problem until I encountered ERROR as follows: AArrgg! @#$
************************************************
Error 0701: USB over current on HC/Port - Bus: 00 H Dev: 1DH Fun: 01 H / Port: 00 H
Error 0701: USB over current on HC/Port - Bus: 00 H Dev: 1DH Fun: 02 H / Port: 00 HPress F1 for Setup, press F12 for Boot Device selection Menu
**********************************************Well, the F1 takes me into the Bios, well all eyes. And F12 does nothing. I tried to boot from the CD drive, but of no use, I tried to solve million methods but invain I could not if anyone has a solution for this, you can provide, I will be very grateful
Thanks in advance
Srini
Insert the cd of the same wait o/s until it reads "loading windows files" then here you eject the cd /dvd. This work for me.
-
XP Professional installation error message after extraction of sp3 on hard disk, message: System cannot find the path specified.
Whenever I try to install, I get the same message. How can I fix it? I can't use the "fix" without sp3 installed.
Any help would be greatly appreciated!"system cannot find the path specified".
A google search revealed this can help...
http://aumha.NET/viewtopic.php?f=62&t=33406Also, what is your level of service current pack (start-run then type Winver, and then press enter)? If you have no current service pack level, you must first install SP2. Unfortunately, the link for that
http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=28
doesn't seem to work today. If all goes well he'll be reinstated soon.
Tricky
-
T230 - recognition USB Flash Drive is intermittent
On the two usb ports, the recognition of a flash drive is intermittent. In its most severe form, you can view the list of drives and look at the logo come and go. Any advice would be appreciated
Do you write unique on a USB device or even occur with different USB devices?
Are you using the original Toshiba recovery image?
-
Tecra 9000 - error message with Windows XP SP3 home edition
Hello
I have a Tecra 9000 in very good condition, until yesterday, I have no problem!
After updating my Windows XP service pack 2 on the "service pack 3", everything works fine but when I press the button 'TOSHIBA controls' and 'mouse' for setting, Windows error message occure: "run a dll as an app"!Even if I go to "Start" and "Control Panel" and press the mouse, after setting close icon, or just simply do nothing (cancel), the same message! I did not notice any other problem with the TOSHIBA utility!
My driver for mouse is "Logitech mouse ware, 9.40! Can you help me?This oldie works well with Windows XP SP2 home edition and in my opinion you should use without SP3. Try to remove the SP3, and I hope that everything will work properly again. Problem is that the old tools and utilities designed for Toshiba probably aren't tested and updated to SP3.
I have more Satellite M70 and use sill with SP3. I don't want to risk anything and have problems.
-
Tecra 9100: error on USB controller drivers
I have a Tecra 9100, would transfer my pictures from my phone to the computer with a USB cable. It gives error like 'there is no driver installed for this device for USB Bus controllers'.
Function using windows, he must be, under the title: controller universal serial bus, "Hi-speed USB.2.0 controllers must be enabled' but there are no Hi-speed USB 2.0 between subtitles.
Could not install a driver or a program from the internet, or is this a hardware problem?
Thank you.
Hello
I think you should check the drivers in Device Manager.
You can download them here:
http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jspGood bye
-
Satellite A100: Error power USB from standby after update BIOS 5.20
Hello
I have problems of USB power since the upgrade my BIOS to 5.2 days on receipt of an email from Toshiba, advise the upgrade
I got a 100 - 200 PSAA8E Windows XP Media Edition since the upgrade of the BIOS to 5.20 I get message error power but only when the computer comes out of standby
The error message tells me that "a USB device has exceeded the limits of its hub port power.
I have nothing connected to one of the USB ports
I talked to guys tech at length to Toshiba, but they can't seem to explain or correct the problem - a same thought it could be a motherboard problem, but cut which like the timing is too coincidental to be something other than the upgrade of the BIOS.
If anyone knows a fix, so I would be grateful - is - it possible to find a previous BIOS and roll back from 5.20
I guess if it's the BIOS, then when they deliver another it will correct itself?
Comments appreciated
Phil
Hello Phil
Maybe again the stupid question, but I also want to know why you made the decision to do the BIOS update? Is there a particular reason or you just want to have laptop with the latest version of the BIOS.
-
Driver for Keysight 34461 A DMM instruments works with GPIB, errors with USB
I try to remotely control a DMM of 34461a Keysight using the driver of instruments located here:
http://sine.NI.com/apps/UTF8/niid_web_display.model_page?p_model_id=21589
The pilot of the aircraft works like a charm the DMM is connected via GPIB, but it error when connected via USB. I've isolated the problem to "Default Instrument Setup.vi". When this VI is called in the case of USB, the device is left in a State which translates by a later call a time-out at VISA Read. The only way I found to get the instrument still talking after this occurs error condition is turned off. I have an another 34461a with the same behavior, is probably not a hardware problem. I can successfully run the example 'Agilent 3446 X series Acquire Single.vi' via USB if I remove all calls to "Default Instrument Setup.vi.
Everyone knows this unit or a similar problem?
I use Windows 7, 2014 SP1 LabVIEW, NI-VISA 14.0.1 and GPIB-USB-HS + (OR-488. 2 14.0) when using a GPIB.
Since the Readme file
3 known issues
Agilent IO Suite must be installed to use the USB interface.
-
Error-200077, USB-6008, deterministic application
Hello
I acquire and generate analog signals using a device USB 6008 to achieve control of feedback. I use a loop of simulation to generate the output of the controller, so need to synchronize signals input/output with the calculation software. I have the following questions:
1. when I use a sample for the analog output clock, I get an error (-200077). What is the cause of this error and are there solutions?
2. what values of step size and calendar period (simulation loop settings) should I use to ensure that determinism?
Your comments are appreciated.
Thank you.
The 6008 doesn't have a clock output. It's software timed and so not deterministic.
-
Original title - USB - IF xHCI USB Host Controller
This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)
I have a permanent error on my computer and when I run the troubleshooter I get the above message. It says Windows cannot load the driver.
Hello
USB devices remove all you can - restart the computer - is still there, the error? If it isn't
It is related to one of the add-in devices that you removed. If she is still there, then, the question is
either a device internal who can not remove or physically with the USB bus itself.
If it was not there, add devices at a time until it is displayed - keep in mind that it is
possible that there are two (or more) devices in conflict over the issue. Once you
identified the check of the aircraft with the help of the manufacturer.1. to find the control panel - device - device - right-click on it - uninstall - Manager then
Restart the computer to see if it clears.2. same place - double click on the device - driver tab - driver update - to see if that helps.
3. check with the support of system manufacturer (manufacturer of motherboard for customized systems), their
online documentation and drivers, diagnostics and ask questions in their forums on all known
questions. Update the Bios and chipset or other USB drivers.=====================================
If necessary, we will use these additional troubleshooting methods:
How to fix Code 31 errors
http://pcsupport.about.com/od/findbyerrormessage/a/code-31-error.htmI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="">-><- mark="" twain="" said="" it="">->
-
Usb modem error device tries to install usb fax modem usb fax modem cannot find system the pilot any idea on how to load the driver?
Hello
What brand / model of the fax machine? What is a printer/Fax?
Download the software complete features driver from the manufacturer's website. It contains the fax driver.
What version of Windows are you using?
-
Hello
I've upgraded to windows 7 on my Pavilion dv7-2180us a few months past without any problems and things worked really well since then.
Last night, however, I started having errors on the usb port.
If I open the Device Manager, it gives me a list of USB devices are working properly, and then lists "unknown device".
If I go to properties it says that it is the standard USB host controller and gives this message:
Windows has stopped this device because it has reported problems. (Code 43)
I've upgraded to the latest Windows hotfix. I have re-downloaded & installed the drivers from the chipset intel from this site and I still get the error.
I checked the event log, but there is no error reported.
Two USB ports are now does not work.
It could be a hardware problem, it could be a driver problem or it could be something to do with other software I have installed...
Any ideas how I can limit?
Thank you
-kevin
It actually turned to be annoyingly easy.
I finally managed to find a web post where someone had the same problem. Taking their suggestion, I turned off the laptop, he unplugged and took out the battery for a few minutes. Then restarted and... * ding *... works very well.
Seems there is a capacitor on the usb controller which must accumulate a load to deodorize the parameters. And unless empty you the load completely from the map, they can get corrupted. As I rarely turn off my cell phone, it never gets drained. I had turned to bike a few times since the problem, but never taken from the battery.
I am pleased, it's a simple solution, but I must admit to being a little disappointed by that. Seems like that should fall into the category 'you should not do. "
* shrug *.
Maybe this will help someone else, at least.
-kevin
-
HP Pavillion Sleekbook 14 TS: error recovery usb device
Today, I tried to retrieve my lapbook back to factory setting. When I bought this laptop that I have been unable to produce a recovery disk so contacted HP they also could not resolve this issue so sent me a USB recovery device that I put aside.
When I tried to use it today it came with the 0130-ABU-ABF error code
My computer is now also come with Boot Device not found
Y at - there anyone out there who is able to help me. Thank you
This has been resolved now. New recovery USB being sent.
-
Disk full error but USB drive has enough free space
I am trying to copy a file to a USB flash drive even if the drive is empty when I try to copy the file, I get an error message telling me that the disk is full. The file is 8GB and the drive is 32 GB, so there is plenty of room. How to fix this?
Most of the USB flash drives are formatted with the FAT32 file system. This file system cannot store any single file larger than 4 GB. You will need to reformat the NTFS-formatted flash drive to store an 8 GByte file. (Attention: save all the files on the drive before reformatting).
"How to use disk management to configure basic disks in Windows XP"
<>http://support.Microsoft.com/kb/309000 >HTH,
JW
Maybe you are looking for
-
How can I change color of default underlining of TextEdit?
I type in the black, but emphasizing the defaults to dark blue. I know how to change the color of the underline manually but I want black underscore by default. How do I do that? I use TextEdit 1.8 in Mountain Lion.
-
How can I stop fax journal reports on Officejet 6600
Do not want to print after every fax fax but newspaper could not find a way to stop it. Nothing in the documentation.
-
How to return to 'now playing' without restarting the track
Hey all,. Received yesterday my first rocket as a belated Christmas gift. I had an old Creative Zen for years. I like the "rocket" so far, but I'm a little confused by one thing. On Zen, I would be on the "Now Playing" screen which shows all the d
-
Hello I am new to the development of native applications from BB using JDE. I'm testing Simulator. From my native BB app, I connect a remote URL and call a Web service method to extract some basic result XML. I need to write a login code remote URL t
-
Hello How to invoke the native calendar to a specific day of the week, as Monday. If today is Monday call for Monday, if today of call Tuesday to next Monday, etc.