Error - the specified i/o operation on Device\Harddisk2\DR4 was not completed before the expiry of the time-out period.

Similar Questions

• The operation of e/s specified on Device\Harddisk2\DR4 was not completed before the expiry of the time-out period

  The operation of e/s specified on Device\Harddisk2\DR4 was not completed before the expiry of the time-out period

  I did no changes on my computer for functionality, commissioning due to above mentioned problem goes & long

  Hi KarlMaskery,

  1. When you receive the error message?

  2. you have any external hard drive connected to the computer?

  3. do you have security software installed on the computer?

  4 when was the last time it was working fine?

  It is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you put the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See the link below to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

• Windows Defender encountered an error: 0x800705b4. This operation completed because the time-out period night.

  Hello

  I'm a Microsoft Online Customer Service, which contacts on behalf of my client. It lights its Windows Defender and received this error message below:

  «Windows defender encountered an error: 0x800705b4.» This operation completed because the time-out period night. »

  Hello

  ·         You have a third-party security software installed on the computer?

  Method 1:

  If so then try to disable the antivirus and then check to see if you can turn on Windows Defender.

  You can check this link for more information on turn Windows Defender on or off: http://windows.microsoft.com/en-US/windows-vista/Turn-Windows-Defender-on-or-off

  Note: Make sure that you enable the antivirus once you are finished with the test. If the problem is resolved, you may need to contact the manufacturer of the program for the settings that can be changed or if there are other updates for this program.

  Method 2:

  Follow the steps in troubleshooting this article and check if that helps:

  How to troubleshoot Windows Defender definition update

  http://support.Microsoft.com/kb/918355

  Also, try the steps in this article: Impossible to activate the application Windows Defender in Windows Vista

  Method 3:

  Try to restart the Windows Defender service and check if it helps.

  a. Click Start on the start menu, search type services.msc and press ENTER.

  b. in the services window, locate Windows Defender service in the services list.

  c. check that the status is started. If the condition column is blank, right-click on the service and select start.

  d. If you get error trying to force start the Windows Defender service, try to change the Startup Type to automatic and restart the computer.

• my windows defender will not open or run. It indicates the time-out period has expired. Help

  an error code appears.  I can not download a new version because my vista comes with window cannot open security Defender.I either.  The time-out period has expired.  What does that mean?

  Hello

  read this information on the Defender:

  ·                         If you use microsoft security essentials avg avira mcafee norton etc they disable the vista version of windows defender by default

  the basics of Microsoft security has its own version of windows defender

  and other anti-virus programs use their own particular type of application to scan for spyware and malware

  It of nothing to worry and is the default action, which is designed for them to do

  If the above does not apply to your machine to read the information on the below link on how to disable the windows defender service in vista or make an autostart to enable

  http://www.groovypost.com/HOWTO/Microsoft/Vista/disable-Windows-Defender-service-in-Windows-Server-2008-or-Vista/

  and here is the method to remove it from startup in vista

  http://www.groovypost.com/HOWTO/Microsoft/Vista/remove-Windows-Defender-from-Vista-system-startup/

  and this is how you would normally activate or disable windows defender in vista from within defenders of own and options tools

  http://www.groovypost.com/HOWTO/Microsoft/Vista/disable-Windows-Defender-for-Microsoft-Vista/

       and read this information to microsoft:

  Error message when you run Windows Defender: «Error 0x800106ba»

  http://support.Microsoft.com/kb/931849

  and if you need to change startup programs read this information on the other methods of doing it without using defender

  using msconfig read this tutorial:

  How to use MSCONFIG in Windows Vista

  Here's how to use MSCONFIG in Windows Vista to disable some unnecessary programs that load automatically at startup

  http://netsquirrel.com/Msconfig/msconfig_vista.html

  and also try this FREE program Autoruns:

  This utility, which has a knowledge of auto-starting locations of any startup monitor, shows you what programs configured to run at system startup or login and that the entries in the order of processing windows. These programs include those in your startup folder, Run, RunOnce, and other registry keys. You can configure Autoruns to show other locations, including Explorer shell, toolbar extensions, helper objects to the browser, Winlogon notifications, auto and many start-up services more

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902

• error code 0x800705b4 windows defender can not turn on because the time-out period expired?

  How to install windows defender without time-out period ending?

  How to install windows defender without time-out period ending?

  Have u installed another anti-virus product? So uninstall it

  List of product anti-malware removal tools
  Windows Defender on Windows 8 - Introduction and frequently asked Questions
  http://answers.Microsoft.com/en-us/protect/Forum/protect_defender-protect_start/Windows-Defender-error-code-0x800705B4/83370876-27Ce-41E9-882e-f78a7f8ef911
  Rarely this may be evanescent and such situation just reboot peut remove...
   
  If the problem continues post here ===> >http://answers.microsoft.com/en-us/protect/forum/protect_defender?tab=Threads

  Edited:updated... links

• Get 'Access denied' vCloud API client after the time-out period

  The .NET tool we build against the API for vCloud strike sometimes a timeout, which will essentially all subsequent calls (at least for the namespaces for example VAPP, Vdc and VM) fails with an access denied message. There is no doubt that this is because a timeout, because that happens only after a certain amount of inactivity.

  Now, I want to try and detect this "timeout" somehow and act accordingly, for example automatically trigger a disconnection and the client connection (instead of making mistakes). The other option is to have a thread keep alive session by calling some resources very, but really, I don't like the idea of ever having any connected clients.

  Any thoughts on how I can detect that the time-out has hit? I can't count on the fact that "Access denied" mean timeout...

  Thank you!

  / Stefan

  infinitesorrow wrote:

  It's a good suggestion, only that I do not directly use the services REST, but the VcloudSDK and the vCloudRestSchema DLL to in .NET... What would be the equivalent of/api/sessions?

  I'm not sure.

  I'm not a .NET programmer (and don't see anything useful in the .NET SDK documentation), but I don't know that the Java development kit has a RestUtil class with a method 'get' that runs on a URL specified by the arbitrary appellant that could be called "/ api / sessions" to do something in this direction in Java. The .NET development kit may have a similar utility class with such a method?

• Phone of blackBerry Smartphones is block after the time-out period

  I recently installed Blackberry Protect on my curve. Before installing it, my phone never locked and required a password to backlight timeout. Now, the phone crashes and requires me to enter a password to use the phone. I would remove this requirement lock without removing Blackberry protect. If anyone can help?

  Honestly, a device security password is not necessary to protect.

  You can disable in Options > Security > password.

• Save before the time-out...

  Hi all...
  
  Please help me solve this problem.
  Let's say I have a simple form 'report' on the EMP table. In my application, I have the "Timeout" for 15 minutes.
  As you know if define us the time-out and the end user is idle for 15 minutes, the application will log them after 15 minutes.
  Is it possible to save your changes, just before the end user got "timed" out
  I mean if the user has made a few changes and idle for 15 minutes and hit the button changes apply after 15 min.
  they lose the changes they made.
  
  Is it possible to save these changes before the time-out period.
  
  
  Thank you

  Yes, there is a difference between these two times.

  I need to get this "APEX downtime" to notify users or make the BACKUP process before that date.

  I don't have your question, I think I got it now, you want to know the downtime from the time displayed on tracks internally within the apex. I couldn't find all the tables where this information is held, probably someone from the dev team can give some information about this part.
  However, you can set a JS variable to the loading of the page with the date and then compare with the current date in JS to get a rough estimate of which (given that the variable gets reset loading the page, so the apex timer is also).

  to run the JS code above, I need to have a (hidden) button with the name 'IDLE_TIME_OUT_SAVE '.

  No you don't need any button, it works fine without it. By default, apex buttons send the page with their name as application, this does not mean that buttons may not submit the page.

• Error "this application has failed to start because normaliz.dll was not found. Reinstalling the application may fix this problem.

  Original title: error explorer.exe, Normaliz.dll is missing please help me about the issue.

  Hello

  I get the error "this application has failed to start because normaliz.dll was not found. Reinstalling the application may fix this problem"Please help me!

  Well - so much for the expertise of committed Microsoft Support Engineer 'experts', but no answer to what I expected.

  See how it works for you:

  If you see a message like this:

  Explorer.EXE - unable to locate component: this application has failed to start because Normaliz.dll was not found. Reinstalling the application may fix this problem.

  It is in the case Log:

  Event type: Information
  Event source: Application Popup
  Event category: no
  Event ID: 26
  Description:

  Application popup: Explorer.EXE - unable to locate component: this application has failed to start because Normaliz.dll was not found. Reinstalling the application may fix this problem.

  Start explorer.exe, but the normaliz.dll file.  If explorer.exe is not able to run, you will not be able to do much with your system until the replacement of normaliz.dll.

  You can click OK for errors and finished up in the Task Manager where you can try to fix it.  The message can keep popping up from time to time, while you're fixing it, so just click OK to close the message.

  If normaliz.dll is missing, you can copy it from a working system to the system afflicted with the same version of XP and Internet Explorer.

  You will get a good copy and put it on a floppy disk, thumb drive etc and copy it to your system plagued by using Manager tasks.

  The normaliz.dll file must be located in the c:\windows\system32 folder and therefore is not a Windows file protected, making the Microsoft Support Engineer 'experts' suggest running sfc/scannow, which is just another one of their prosecution of wild goose that will not work, he'll never work and it will only waste your time (and they don't tell you how to run either - if explorer.exe does not start).

  Then engaged Microsoft Support Engineer 'experts' will offer to you develop a copy of the file from the XP installation CD you probably haven't, but it is also not on your XP installation CD, and you will have the same problem try their suggestions to 'try' to start in any any Mode without failure, so this will not help you.  These "experts" seem to think that the Safe Mode boot or boot will replace magically missing files, but it doesn't.

  You also will be able to properly run a browser on the system afflicted to go on Internet download one.

  There is a large computer security risk in the normaliz.dll from some website download.  The best idea is to get a copy of normaliz.dll from another computer that has the same version of XP and IE and replace it from a USB device (which you can access from the Manager tasks), or using a system that works, you can download one of my SkyDrive.

  You can still use the Task Manager to run the system restore and bring it back, but I've never tried and never use SR in all cases.

  If you have recently done a bunch of Microsoft updates, you may have also gotten IE8 so maybe that something was wrong here although the normaliz.dll is the same for each version.

  When you see the error, you can click beyond it and eventually arrived at your screen background image where you can press CTRL-ALT-DEL to start Task Manager. TM, you can click file, new task, Browse and edit the menu drop-down "Files of type" to all files that you can see all the files in folders.

  Go to c:\windows\system32 to see if normaliz.dll is really missing. If the error appears again while browsing, just click OK to get past it.  The explorer.exe tries to run and cannot until the missing file is replaced.

  If it's the only thing missing, you can get one from a working system of the same type as yours, copy on a Flash DRIVE or a floppy disk and always using TM, to browse, copy and paste it where it should be or you can download one of my SkyDrive.

  TM, you can still access your thumb or any other medium the same disk by navigating, copy, paste, etc very well all work.  You use TM to navigate to your thumb or floppy disk, copy the normaliz.dll good and then paste it in the c:\windows\system32 folder, where it is supposed to be.

  If things get worse, just return to TM and remove the file back where you were in first place and continue troubleshooting.

  Using a system that works, you can also download a copy of the file from my SkyDrive and put it on a floppy or USB thumbdrive and networks diskettes for the distressed system.  Sandalenet means wear you the system afflicted by hand.

  I downloaded a copy of XP Pro SP3 file you need on my SkyDrive (everyone has a SkyDrive for file sharing).

  You can download it and when you do, place a copy of the file in these two folders (assuming that Windows is installed on your C drive):

  c:\Windows\System32

  Here is the link to my SkyDrive and you can get the file you need here:

  https://SkyDrive.live.com/?CID=6a7e789cab1d6f39&ID=6A7E789CAB1D6F39! 311

  When you see the files available for download, you can not see the file extension (.exe, .dll, .cpl, .sys, .zip, etc.), but when download you them they will have the right extension.

  When you download the file (especially if you use Internet Explorer), when you get a chance to save the file, your browser is unable to save the file with an extension (by example, .exe, .dll, .cpl, .sys, .zip, etc) then you will need to manually add the extension appropriate to the file when you download the file before you save it.

  You can download the file without the extension, and then rename the file to add the appropriate extension.  You do not want to use a file called normaliz when the name of the file should really be called normaliz.dll (if the downloaded file has no extension, you will need to change the name of the file to add the appropriate extension to make it work.

  You then put the downloaded files in the correct folders on your system.

  That may not solve all your problems, but at least you will be spending this part and we can then fix the rest.

• The device, \Device\Harddisk2\D, is not ready for access yet.

  Event Viewer has many entries of error ID 15, which States:
  The device, \Device\Harddisk2\D, is not ready for access yet.

  What does that mean?  Is this an indication of imminent drive failure?

  Hello

  ·         Did you of recent changes to the computer before the show?

  Method 1: Check that all connectors (power and IDE) should be firmly fixed. Disconnect and reconnect to check.

  Method 2: As short-term solution, try to shut down the system, turn the power off, turn on the power and restart. If the device still does not work then it is probably a problem of material, the device or card/main controller card (or possibly the cable connection) will need to be replaced. If the device seems to work then this indicates a problem of software or firmware. Do not forget that the problem can recur again unless the root causes addressed.

  Method 3: Update the latest version of the device driver (if there is one).
  Check on the Web site of the vendor for a newer driver and if it is available then load it.

  Reference: http://support.microsoft.com/kb/283658

  Method 4: Enforcement Procedure in Windows XP check disk errors

  http://support.Microsoft.com/kb/315265

  CHKDSK warning:

  Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

• Change the time-out for the vote of the files

  Hey, is there a way to change the default time-out for files with right to vote. The idea: I have a grid storage (soft). Then I configured the external redundancy for my roc diskgroup where is my votingfile.
  
  When one of the stored mirror gets turned off, the system hungs for almost 2 minutes. The deadline to vote is set to 99 seconds, right? This should be the default setting, at least, according to the journal of crs alerts.
  
  Is it possible to change this value?
  
  At present, the database gets shutdown, after which expires the time-out.
  
  Christian

  Hello
  This note will help you with the IO time-out, but I think that's not your problem.

  See:
  Component sync (CSS) of the Oracle Clusterware services maintains two mechanisms of heartbeat heart 1.) the heart rate of the disk on the device with the right to vote and 2.) the heartbeat of the interconnection network which establish and confirm the valid membership of node in the cluster. Both of these mechanisms of heart beat have a timeout associated value. The heartbeat of disc has an interval of time-out of e/s internal (DTO disk time-out), in seconds, to complete an i/o to the drive to vote. The parameter misscount (MC), as noted above, is the maximum time, in seconds, that can not miss a heartbeat of network. The e/s disk heartbeat time-out interval is directly related to the setting of parameter misscount.

  Change the default value of misscount not only affects the delay interval to wait for IO to the drive to vote, but also affect the tolerance of pulses missed through the interconnection network.

  MissCount should NOT be changed to work around the problems mentioned below.
  HBA QLogic cards with a link down Timeout greater than the default misscount.
  Cables wrong with Matrix Storage/SAN this purpose IO latencies
  SAN switch (such as Brocade) failover latency greater than the default misscount
  EMC Clariion array at the intrusion of the AOC for superior to default misscount MS backup
  EMC PowerPath path and to repost IO error detection and redirect than default misscount
  Bad network configuration SAN that creates latencies in the path of the I/O.

  Then I configured the external redundancy for my roc diskgroup where is my votingfile. When one of the stored mirror gets turned off, the system hungs for almost 2 minutes.

  As you use external redundancy Oracle knows not that there is a disk mirrored by behind.
  Perhaps the OS or storage keep I/O when you stop mirroring due to a bad configuration. I think that this problem is related to the OS or storage not the Oracle Clusterware.
  If you perform this test with the diskgroup (external redundancy) storing data will have the same result.

  Kind regards
  Levi Pereira

• How to change the time-out setting

  Hi all
  
  IM new to oracle10g. We use Server 10g 2 version. We have a report that runs for more than 5 minutes. After 5 minutes, the time-out error message is displayed. How to avoid this problem. I gave the value of forms_timeout 1400 in default.env. Even after that, im getting the same message. Is there something else to do to avoid this error in time-out?
  
  Below the message after 5 minutes.
  
  Explanation: the request expired before the page could be found. *
  
  
  Try this:*.
  
  Refresh page: search for the page again by clicking the Refresh button. This may have been a mistake for a moment. *
  
  If you are still not able to view the requested page, try contacting your administrator or your Helpdesk. *
  
  
  
  
  Technical (for support staff) information*.
  
  Error code 1460: Timeout*.
  
  Background: the gateway could not receive a timely response on the site you are trying to access, a DNS server, or another gateway server. This might indicate that the network is congested, or that the site is experiencing technical difficulties. *
  
  
  Thanks in advance
  Robet

  I don't think that this forms_timeout applies here, as it should be an HTTP request and forms_timeout has nothing to do with it.
  Check the file httpd.conf of your apache located in $ORACLE_HOME/apache/apache/conf for the TimeOut directive. The default value is 300 seconds which would be your 5 minutes, then perhaps assigning a higher value should do the job.

  But a report that lasts more than 5 minutes? Isn't it a little longer? If I was a user who runs this report would probably cancel the execution, as if I have to wait longer than 5 minutes for my desired output I'm sure I want to cancel it, as I suspect that it is more. I am looking for the cause of this; Maybe you have a plan of bad execution of your report, or maybe you need to redraw your sql to run faster...

  concerning

• How to adjust the time-out setting?

  I'm in a certain OBIEE in Firefox which, by nature, do not take a long time to run. One of my local Technical Support people suggested increase Firefox's timeout setting (he showed me how to do this once, but I didn't write it). Can you provide instructions written (or annotated images of the screen), please?

  Alright. There are two ways to do this. You can extend your timeout, or you can completely disable timeout. Depending on how you are using firefox, can be useful. If you want to extend your time-out, type about: config in your search bar on the top. From there, need you a list of preferences. There is a search bar. Type "Timeout" in there. The top two are disable the time-out and the 'County timeout'. If you want to disable the timeout, simply double-click the "enabletimeout" on the top. This will change the false value. If you want to change the value of how long it takes to timeout, double-click on the "CountTimeout" and type in your new value. If this is not sensible, see screenshots.

  Have a great day!

  -Jon

• Disable the time-out SSH ESXi 4.1?

  Hi all

  I use a scheduled task and ghettoVCB to back up ESXi system, but the SSH timeout keeps giving me grief, is it possible to disable the time-out and have the demon of support tech SSH running all the time?

  See you soon,.

  Joe

  You can disable SSH timeout by setting the value 0, which disables the time-out all together. To do this, you will use the DCUI. Take a look at this VMware KB which guides you through the activation process of TSM - http://kb.vmware.com/kb/1017910 and you are going to disable the timeout TSM

• How to add the time-out explicit?

  In my load test script, I want to add an explicit delay between 2 markets. For example, the script should always take a break of 60 seconds between step 1 and step 2. This time-out period is different from the user think that the time and must be unchanged, so I can't use think(). There is another function that is paused the script for a pre-defined period?

  Hi MingyuCheung,

  Please try to use delay().

  Kind regards
  Anand