Save before the time-out...

Similar Questions

• Error - the specified i/o operation on Device\Harddisk2\DR4 was not completed before the expiry of the time-out period.

  Original title: XP USB device timeout - is there a solution?

  Under all the circumstces I get: "Windows - Device Timeout" The specified IO on Device\Harddisk2\DR4 did not complete before the time-out expired period.  The drive is a Sony external 150 GB USB2.  The only way to remedy this is turned off and let windows re - recognize.  It stops usually after 18minutes regardless of activity. I did all the USB install no etc no difference.  Please advise as soon as POSSIBLE!  Please not flaky ideas or suggestions.  P.S > I looked the FIX for USB, but it is not specific to my question - if I ask this question instead.

  Hello

  ·        What is the brand and the model of your machine?

  ·        What steps you have tried to solve the problem other that Reinstall USB?

  ·        You did it all change hardware or software on your machine before this problem?

  You can contact the manufacturer of your computer to update the chipset drivers and check if the problem persists.

  Note: Changing the BIOS / chipset can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/chipset can be solved. Changes to settings are at your own risk.

  Hope the helps of information. Please post back and we do know.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• The operation of e/s specified on Device\Harddisk2\DR4 was not completed before the expiry of the time-out period

  The operation of e/s specified on Device\Harddisk2\DR4 was not completed before the expiry of the time-out period

  I did no changes on my computer for functionality, commissioning due to above mentioned problem goes & long

  Hi KarlMaskery,

  1. When you receive the error message?

  2. you have any external hard drive connected to the computer?

  3. do you have security software installed on the computer?

  4 when was the last time it was working fine?

  It is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you put the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See the link below to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

• my screen saver does not start. I select a screen saver, set the time, apply and nothing. This has happened before and corrected himself. Maybe one setting in another program? ___

  I select a screen saver, set the time, apply and nothing.  This has happened before and corrected himself.  Maybe one setting in another program? It's on a laptop.

  Hello jerrylumpe

  1. If you use an old mouse, try to clean it.

  2. you can have a running process in the background that keeps XP thinking that he is busy and so the screen standby does not start.
  Go to msconfig and uncheck everything you don't need, then see if the screensaver will kick in.

  Start/run and type
  Msconfig
  Ok

  Startup tab
  Keep the page open then click on the link below. It will tell you what are all the entries and see if you can disable them or not

  http://www.SysInfo.org/STARTUPINFO.html

  Read the key at the foot of the page, then click on "Here" at the top. Use the search box to check all your entries

  Try this too
  http://www.kellys-Korner-XP.com/xp_tweaks.htm

  Line 51 left side. Click on "toggle".

  It could be that something is resetting the timer. For example, it does take much vibration to move the mouse a little, and which will reset the timer to zero. Something like that would be possible? Or a pet that walks on the keyboard?

• How to change the time-out setting

  Hi all
  
  IM new to oracle10g. We use Server 10g 2 version. We have a report that runs for more than 5 minutes. After 5 minutes, the time-out error message is displayed. How to avoid this problem. I gave the value of forms_timeout 1400 in default.env. Even after that, im getting the same message. Is there something else to do to avoid this error in time-out?
  
  Below the message after 5 minutes.
  
  Explanation: the request expired before the page could be found. *
  
  
  Try this:*.
  
  Refresh page: search for the page again by clicking the Refresh button. This may have been a mistake for a moment. *
  
  If you are still not able to view the requested page, try contacting your administrator or your Helpdesk. *
  
  
  
  
  Technical (for support staff) information*.
  
  Error code 1460: Timeout*.
  
  Background: the gateway could not receive a timely response on the site you are trying to access, a DNS server, or another gateway server. This might indicate that the network is congested, or that the site is experiencing technical difficulties. *
  
  
  Thanks in advance
  Robet

  I don't think that this forms_timeout applies here, as it should be an HTTP request and forms_timeout has nothing to do with it.
  Check the file httpd.conf of your apache located in $ORACLE_HOME/apache/apache/conf for the TimeOut directive. The default value is 300 seconds which would be your 5 minutes, then perhaps assigning a higher value should do the job.

  But a report that lasts more than 5 minutes? Isn't it a little longer? If I was a user who runs this report would probably cancel the execution, as if I have to wait longer than 5 minutes for my desired output I'm sure I want to cancel it, as I suspect that it is more. I am looking for the cause of this; Maybe you have a plan of bad execution of your report, or maybe you need to redraw your sql to run faster...

  concerning

• How to adjust the time-out setting?

  I'm in a certain OBIEE in Firefox which, by nature, do not take a long time to run. One of my local Technical Support people suggested increase Firefox's timeout setting (he showed me how to do this once, but I didn't write it). Can you provide instructions written (or annotated images of the screen), please?

  Alright. There are two ways to do this. You can extend your timeout, or you can completely disable timeout. Depending on how you are using firefox, can be useful. If you want to extend your time-out, type about: config in your search bar on the top. From there, need you a list of preferences. There is a search bar. Type "Timeout" in there. The top two are disable the time-out and the 'County timeout'. If you want to disable the timeout, simply double-click the "enabletimeout" on the top. This will change the false value. If you want to change the value of how long it takes to timeout, double-click on the "CountTimeout" and type in your new value. If this is not sensible, see screenshots.

  Have a great day!

  -Jon

• Windows Defender encountered an error: 0x800705b4. This operation completed because the time-out period night.

  Hello

  I'm a Microsoft Online Customer Service, which contacts on behalf of my client. It lights its Windows Defender and received this error message below:

  «Windows defender encountered an error: 0x800705b4.» This operation completed because the time-out period night. »

  Hello

  ·         You have a third-party security software installed on the computer?

  Method 1:

  If so then try to disable the antivirus and then check to see if you can turn on Windows Defender.

  You can check this link for more information on turn Windows Defender on or off: http://windows.microsoft.com/en-US/windows-vista/Turn-Windows-Defender-on-or-off

  Note: Make sure that you enable the antivirus once you are finished with the test. If the problem is resolved, you may need to contact the manufacturer of the program for the settings that can be changed or if there are other updates for this program.

  Method 2:

  Follow the steps in troubleshooting this article and check if that helps:

  How to troubleshoot Windows Defender definition update

  http://support.Microsoft.com/kb/918355

  Also, try the steps in this article: Impossible to activate the application Windows Defender in Windows Vista

  Method 3:

  Try to restart the Windows Defender service and check if it helps.

  a. Click Start on the start menu, search type services.msc and press ENTER.

  b. in the services window, locate Windows Defender service in the services list.

  c. check that the status is started. If the condition column is blank, right-click on the service and select start.

  d. If you get error trying to force start the Windows Defender service, try to change the Startup Type to automatic and restart the computer.

• my windows defender will not open or run. It indicates the time-out period has expired. Help

  an error code appears.  I can not download a new version because my vista comes with window cannot open security Defender.I either.  The time-out period has expired.  What does that mean?

  Hello

  read this information on the Defender:

  ·                         If you use microsoft security essentials avg avira mcafee norton etc they disable the vista version of windows defender by default

  the basics of Microsoft security has its own version of windows defender

  and other anti-virus programs use their own particular type of application to scan for spyware and malware

  It of nothing to worry and is the default action, which is designed for them to do

  If the above does not apply to your machine to read the information on the below link on how to disable the windows defender service in vista or make an autostart to enable

  http://www.groovypost.com/HOWTO/Microsoft/Vista/disable-Windows-Defender-service-in-Windows-Server-2008-or-Vista/

  and here is the method to remove it from startup in vista

  http://www.groovypost.com/HOWTO/Microsoft/Vista/remove-Windows-Defender-from-Vista-system-startup/

  and this is how you would normally activate or disable windows defender in vista from within defenders of own and options tools

  http://www.groovypost.com/HOWTO/Microsoft/Vista/disable-Windows-Defender-for-Microsoft-Vista/

       and read this information to microsoft:

  Error message when you run Windows Defender: «Error 0x800106ba»

  http://support.Microsoft.com/kb/931849

  and if you need to change startup programs read this information on the other methods of doing it without using defender

  using msconfig read this tutorial:

  How to use MSCONFIG in Windows Vista

  Here's how to use MSCONFIG in Windows Vista to disable some unnecessary programs that load automatically at startup

  http://netsquirrel.com/Msconfig/msconfig_vista.html

  and also try this FREE program Autoruns:

  This utility, which has a knowledge of auto-starting locations of any startup monitor, shows you what programs configured to run at system startup or login and that the entries in the order of processing windows. These programs include those in your startup folder, Run, RunOnce, and other registry keys. You can configure Autoruns to show other locations, including Explorer shell, toolbar extensions, helper objects to the browser, Winlogon notifications, auto and many start-up services more

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902

• Get 'Access denied' vCloud API client after the time-out period

  The .NET tool we build against the API for vCloud strike sometimes a timeout, which will essentially all subsequent calls (at least for the namespaces for example VAPP, Vdc and VM) fails with an access denied message. There is no doubt that this is because a timeout, because that happens only after a certain amount of inactivity.

  Now, I want to try and detect this "timeout" somehow and act accordingly, for example automatically trigger a disconnection and the client connection (instead of making mistakes). The other option is to have a thread keep alive session by calling some resources very, but really, I don't like the idea of ever having any connected clients.

  Any thoughts on how I can detect that the time-out has hit? I can't count on the fact that "Access denied" mean timeout...

  Thank you!

  / Stefan

  infinitesorrow wrote:

  It's a good suggestion, only that I do not directly use the services REST, but the VcloudSDK and the vCloudRestSchema DLL to in .NET... What would be the equivalent of/api/sessions?

  I'm not sure.

  I'm not a .NET programmer (and don't see anything useful in the .NET SDK documentation), but I don't know that the Java development kit has a RestUtil class with a method 'get' that runs on a URL specified by the arbitrary appellant that could be called "/ api / sessions" to do something in this direction in Java. The .NET development kit may have a similar utility class with such a method?

• Disable the time-out SSH ESXi 4.1?

  Hi all

  I use a scheduled task and ghettoVCB to back up ESXi system, but the SSH timeout keeps giving me grief, is it possible to disable the time-out and have the demon of support tech SSH running all the time?

  See you soon,.

  Joe

  You can disable SSH timeout by setting the value 0, which disables the time-out all together. To do this, you will use the DCUI. Take a look at this VMware KB which guides you through the activation process of TSM - http://kb.vmware.com/kb/1017910 and you are going to disable the timeout TSM

• Disable the button Save all the time

  Hello! I want to have a form that is with button "DISABLE" save all the time. When I put this code below into the trigger once - new - form - Instance:
  

  Set_Menu_Item_Property('Action.Save', ENABLED, PROPERTY_FALSE ) ;  

  first of all, it's disable, but when I click the "RUN" button, the "Save" button is again enable. My question is where I must put the code above to disable the button Save all the time.
  
  TX in advance.

  indoracle wrote:
  Hello! I want to have a form that is with button "DISABLE" save all the time. When I put this code below into the trigger once - new - form - Instance:

  Set_Menu_Item_Property('Action.Save', ENABLED, PROPERTY_FALSE ) ;  
  

  first of all, it's disable, but when I click the "RUN" button, the "Save" button is again enable. My question is where I must put the code above to disable the button Save all the time.

  TX in advance.

  Hello
  Is there another code in the form to activate this?

  Try the code at the moment-new Record Instance to the block level.

  Hope this helps.

• Change the time-out for the vote of the files

  Hey, is there a way to change the default time-out for files with right to vote. The idea: I have a grid storage (soft). Then I configured the external redundancy for my roc diskgroup where is my votingfile.
  
  When one of the stored mirror gets turned off, the system hungs for almost 2 minutes. The deadline to vote is set to 99 seconds, right? This should be the default setting, at least, according to the journal of crs alerts.
  
  Is it possible to change this value?
  
  At present, the database gets shutdown, after which expires the time-out.
  
  Christian

  Hello
  This note will help you with the IO time-out, but I think that's not your problem.

  See:
  Component sync (CSS) of the Oracle Clusterware services maintains two mechanisms of heartbeat heart 1.) the heart rate of the disk on the device with the right to vote and 2.) the heartbeat of the interconnection network which establish and confirm the valid membership of node in the cluster. Both of these mechanisms of heart beat have a timeout associated value. The heartbeat of disc has an interval of time-out of e/s internal (DTO disk time-out), in seconds, to complete an i/o to the drive to vote. The parameter misscount (MC), as noted above, is the maximum time, in seconds, that can not miss a heartbeat of network. The e/s disk heartbeat time-out interval is directly related to the setting of parameter misscount.

  Change the default value of misscount not only affects the delay interval to wait for IO to the drive to vote, but also affect the tolerance of pulses missed through the interconnection network.

  MissCount should NOT be changed to work around the problems mentioned below.
  HBA QLogic cards with a link down Timeout greater than the default misscount.
  Cables wrong with Matrix Storage/SAN this purpose IO latencies
  SAN switch (such as Brocade) failover latency greater than the default misscount
  EMC Clariion array at the intrusion of the AOC for superior to default misscount MS backup
  EMC PowerPath path and to repost IO error detection and redirect than default misscount
  Bad network configuration SAN that creates latencies in the path of the I/O.

  Then I configured the external redundancy for my roc diskgroup where is my votingfile. When one of the stored mirror gets turned off, the system hungs for almost 2 minutes.

  As you use external redundancy Oracle knows not that there is a disk mirrored by behind.
  Perhaps the OS or storage keep I/O when you stop mirroring due to a bad configuration. I think that this problem is related to the OS or storage not the Oracle Clusterware.
  If you perform this test with the diskgroup (external redundancy) storing data will have the same result.

  Kind regards
  Levi Pereira

• Reset the time-out without clicks or the keyboard input

  Hey all,.
  SO, I have a RFID reader that triggers events in a film's Director. My timeout is set to 2 minutes, but it is possible for the user to never touch the keyboard or touch screen and always in interaction with the program through the RFID interface. How can I reset the timer of the time-out for the program don't timeout in the middle of the activity of the user. I can't find anything in the documentation that says, although it seems that there should be a property that I could put everything back to 0. Like countDownTime or something like that. Any ideas?
  
  -Bruce

  > it seems there should be some
  > property that I could just reset to 0.

  If you use the ' timeout' Manager (and setting of the)
  timeoutLength), try to reset 'timeoutLapsed' to zero when you need to.

• Is it possible to extend the time-out of release of app?

  My application must save the State of closure project, so I'm handles the NAVIGATOR_EXIT message and start my save shared storage then.

  The problem is, the project files can be quite large (up to 10 MB) based on the content of the user and because the app has ~ 500ms to exit before the system with force to stop him, I run into cases where automatic registration fails to complete. I can handle the case of the file does not completely recorded at the start of the next time, but it means a bad user experience because they will potentially have lost their jobs.

  The API reference says that an application can call navigator_extend_timeout() to allow up to 30 years create the window. I would like to know if there is an equivalent to extend the forced timeout app closed the same way or something equivalent?

  I have 30 seconds, just need 1-2 more... even if it is performed in the background at low priority without window at this time.

  It is a feature under the BPS.

  It will be available in a future release.

  Please stay tuned!

• Help: How do reset you default values for the session and the time-out at the admin level

  Hello
  
  The DBA was trying to save the settings of time-out value by following the instructions and it kept him setting a default off 28800 timeout of Session Timeout and Idle of 3600.
  
  He saved the value 1, and now we cannot get to change.
  
  How do reset you the default preferences?

  Bill,

  Sorry, I missed your point. To undo this damage, try this:

  Connect as SYS

  ALTER session set current_schema = apex_030200
  /
  wwv_flow_platform.set_preference (p_preference_name-online 'MAX_SESSION_IDLE_SEC', p_preference_value-online 3600)
  /
  wwv_flow_platform.set_preference (p_preference_name-online 'MAX_SESSION_LENGTH_SEC', p_preference_value-online 28800)
  /
  Commit
  /

  Adjust 3600 and 28800 as you like.

  Scott