Error to delete using the Delete Trigger

Similar Questions

• IMAQ Grab Acquire.vi error when you use an external trigger on a card NI PCIe-1433 (sync problem?)

  According to my recent post on getting up and running with the NI PCIe-1433 camera link card, I ran into a bit of a snag.

  When you use the internal trigger on the camera, everything works 100%. I can view all the data from the camera in MAX as well as in the labview project. However, whenever I have set the mode switch is where things start to fall apart.

  What I have confirmed:

  -Camera is switching between inside and outside triggering.

  -NI PCIe-1433 camera link card is set up properly. While in external mode, I can trigger the camera by using a function generator and check the wire to the MAX. Everything works fine.

  When the unit is in external mode, the function Acquire.vi enter IMAQ - my mistake VI. The error is:

  Code :-1074397150

  The possible reasons for a timeout.

  Now, I have it set up so that a mistake here will not end the LabVIEW file. Sometimes, data of interest makes however (about every 10 seconds-ish). So what seems to be the case, it's that this external trigger signal is not in the lineup when the clamp is attempted. Is it possible to synchronize these? May reference the trigger signal external sort in my LabVIEW project so that the clamp is performed only when that trigger impulses?

  So I solved my problem. He was in time. The external trigger that I used for the device was simply too slow. I was initially using a trigger from 2 Hz to be able to view the values changing on LabVIEW probes. But it was enough to get enough data to move above the camera cable to assemble a picture and kept it in time. Travel up to 9 kHz solved the problem. No adjustment to the camera settings or LabVIEW code was necessary.

• build error of createUser using the c# code sample

  I get the following build error when you use the c# code for the createUser use method example.

  I use VisualStudio2008 and the Blackberry_Admin_API - 5.0 - US.pdf c# code example.

  Build error States:

  Cannot implicitly convert type 'BESAdmin.BASemailExchangeWebService.EnableBlackBerryUserAttributesType' in 'BESAdmin.BASCoreWebService.EnableBlackBerryUserAttributesType' C:\VS2008\BESAdmin\BESAdmin\Form1.cs 76 488 BESAdmin

  The build error is on this part of the code:

  for (int j = 0; j)< attributes.enableblackberryuserattributes.length;="">

  {

  userEnableBBAttributes.enableBlackBerryUserAttributes [j] = attributes.enableBlackBerryUserAttributes [j];

  }

  Everyone has this same problem and found the solution?  It seems that there is something missing or incorrect in the sample code around type conversion between the EnableBlackberryAttributesType.

  Thank you, Ed

  Hi Ed,

  I tried throwing the code example in a project already created the mine and has not known this error at compile. The two types of objects must be the same, so I don't know why there is no conflict with assignment.

  Please try to use the sample code to create a user from the BAA API reference documents:

  http://www.BlackBerry.com/developers/docs/BAA/5.0.0/

  Or the Knowledge Base of the developer section:

  http://www.BlackBerry.com/knowledgecenterpublic/livelink.exe/fetch/2000/348583/1608023/How_To_-_Get _...

  It can also be a good idea to recreate your proxy to do this.

  Let us know if the problem is still evident with the examples above.

• In CS2 program error: "could not use the text because of a program error."

  Yesterday when using the text tool, I kept getting the message "Could not use the text tool because of a program error". Today I still get this message and the same message when I try to change the size of the image. There is no information on what the program error is - all advice?

  This can be caused by a corrupt police.

  If you are on a Mac, FontBook open, select all (Cmd + A) fonts, file > validate font. Check fonts corrupted / invalid according to the results. Delete all corrupt fonts. Try using the text tool now.

  If you are under Windows, use this: http://fix-fonts-folder.en.softonic.com/ or search for one of the many programs on Google font manager.

  -ST

• 200077 error has occurred to the property trigger Node DAQmx DAQmx Start Trigger (analog Edge.vi:1-&gt; CRT with trigger

  I created a program that reads analog data and draw a waveform, but I need to stop the program when the voltage drops to a certain tension. When I tried the analog edge trigger it showed the error in the subject:

  Reason: The requested value is not supported for this property value. The value of the property may be invalid because it is in conflict with another property.

  Property: Trig startup type

  Requested value: analog edge

  You can select: Digital Edge, no

  I understand what the analog trigger is not available for my DAQmx version, without again getting equiptment, can I use a trigger to stop reading data at a specific voltage?

  How to start and stop a similar read digital triggering?

  Thanks in advance!

  Ah! Well, then the Boolean value of status would be connected to the State of the thread of the unbundled error, Boolean stop to the stop button and the Boolean value to the right would be the stop for loop itself... so something like this (see image).  This is an excerpt from LabVIEW 2014, so it can not easily fall in your version, but I hope it's clear enough on how you can wire it to the top.

• Libretto U100 - error if I use the SD memory Boot utility

  Hello

  I'm trying to format and install a starter BACK on a 2 GB SD system. Laptop is a Libretto U100.

  I can read and write the 2 GB SD used in my digital camera cards.

  As far as I can tell the SD memory card Format program works well. But when I run the utility Boot memory SD I always the following error message:

  TSDBOOT

  Error reading. This disc may be unformatted or is not inserted.

  I don't have a floppy drive, so I always use the option 'Read from an image file.
  I used VFD to create a virtual floppy drive that I formatted as a bootable diskette, and recorded an image of it. But I've also tried other images, I found using Google.

  I tried two different SD cards by two different manufacturers.
  I've updated the BIOS with the latest version on this site.
  I checked the version of compatible SDA Standard SD Host Controller and it's the last. But I uninstalled and reinstalled in all cases.
  I tried to format with SDFormatter V2.0.0.3 by Panasonic SD cards

  All to nothing does not. Whenever I get exactly the above error.

  I try next?

  Mike

  Mike Merci for the comments.

• Error code #0xe0f00013, using the factory image restore

  Hello world

  I've had this laptop for about 8 months. The model is HP PAVILION DV6T-4000 NOTEBOOK of NOTES,

  I'm a software developer, so I need to install Linux on this machine using dual boot.

  I created the recovery disks before installing linux.

  Once I installed linux, windows 7 has stopped working and started asking for the disc of windows 7. Using recovery discs, couldn't find an option to restore the old installation of windows 7 (these options are disabled). Other options of formatting HD and restore out-of-factory State were available. In the end, I had to select restore factory image.

  When I boot the recovery dvd and do a system restore it support all 5 discs and the 6th disc when it is 83% and is "copy files needed to restore the hard disk" it throws below error:

  "Recovery Manager is unable to restore your computer by using the original image.  Please contact HP support.  "Error code: 0xe0f00013.

  I tried to restore it 3 - 4 times, each time that the result would be the same.

  I ran HD self-test, which doesn't show any problem with my HD recovery, I created discs are cool and have no scratches. I'm not sure what the cause of this problem.

  All this raises questions under:

  (1) what is the hexadecimal code "0xe0f00013?"

  (2) once we buy a "personal" NOTEBOOK, should we not be free to install any operating according to our need?

  3) why HP does not provide with a Windows disc, and why should we depend on recovery disks, or the recovery partition; These unreliable mechanisms?

  Earlier, I had a Dell laptop that provided me with all the windows and recovery disks.

  I bought HP recovery discs. lets see if provided HP recovery disks.

  If anyone has any other work around, please help.

  Thank you.

  Hello

  There may be a work-around if you have (or can borrow) an installation disc Windows 7 at retail which is exactly the same version as your OEM installation - IE if your laptop comes with Windows 7 Home Premium 64-bit, it comes to the retail version accurate, you would need.

  If you do not access to the retail drives, you can create an installation disk yourself - just download good picture disc from the link below and use an app like ImgBurn to burn the ISO correctly on a blank DVD.

  http://www.mydigitallife.info/Download-Windows-7-ISO-official-32-bit-and-64-bit-direct-download-link...

  Use the disk to perform the installation, enter the Windows activation key located on the underside of your laptop when asked and once installation is complete, use the 'method of phone", described in detail in the link below to activate the operating system - this method supported by Microsoft and is popular with people who want to just have a new installation of Windows 7 without additional software load normally comes with OEM installations.

  http://www.kodyaz.com/articles/how-to-activate-Windows-7-by-phone.aspx

  Additional drivers, you may need to find from here.

  Kind regards

  DP - K

  

• Evanescent synchronization using the TTL trigger

  Hi all

  I work with the NI DAQ (PCIe 6363) set and uses a waveform as outputs analog to control a scanning unit.

  Now I want this output to synchronize with the rising edge of an external TTL signal (the * fire * out of a camera).

  To do this, I used [Cont Gen tension Wfm - Int Clk - analog Start] - model with minor changes (see attachment with a few comments included). In fact, it works, but only if the output signal is long finished when arrives the next TTL climbing aboard. What I want is a rising edge trigger that happens, say, 100 Hz, and a waveform near 10 ms-long that starts with this trigger. So far, I have to operate with a approx. 8 ms wavelength. It seems to me that the loop in Labview (see attachment) software takes the rest of the time. If I increase the wavelength to 9 ms or more, the loop is too slow and little miss the next rising edge trigger.

  Unfortunately, I can't use [continuous sampling] that there is too much instability in the external trigger.

  Is it possible to optimize this problem? For example, is it possible to tell la carte DAQ 'turn off this waveform whenever you receive the trigger"instead of"put on this waveform when you receive the trigger, then shut up? " Or is it possible to run two while loops in parallel that alternately hold the trigger signal and both use the same output channel? There is another, simpler solution?

  Thanks for the pointers,

  Peter

  You must use the property start.retriggerable, something like this:

  

  Best regards

• Error 39 cannot use the CD player.

  Original title: Qwest internet installed last week. now, I can't use the cd player.

  How can I fix my cd deive

  Hi Bonnie,.

  1. what happens when you try to use the CD player?

  2. you receive an error message or code?

  Please provide us with more information about the issue so that we can provide you with the necessary assistance.

• Compilation error when you use the NDK library

  Hello

  I am developing an application of cascades that uses a static library NDK to communicate with a bluetooth device. The NDK library compiles without problems, but when I then compile the application stunts I get errors with all bluetooth NDK functions:

  myBB10Lib.a(BluetoothDevice.o): In function `MyBB10Lib::BluetoothDevice::getAddress()':
  \src\Driver/BluetoothDevice.cpp:33: undefined reference to `bt_rdev_get_address'
  
  myBB10Lib.a(BluetoothDevice.o): In function `MyBB10Lib::BluetoothDevice::getName()':
  \src\Driver/BluetoothDevice.cpp:53: undefined reference to `bt_rdev_get_friendly_name'
  
  make[2]: *** [o.le-v7-g/MyCascadesProject] Error 1
  make[1]: *** [debug] Error 2
  make: *** [Device-Debug] Error 2
  

  (I create a static library as it will act as a driver for the bluetooth device in other applications of stunts in the future).

  I have good include (#include ) in the BluetoothDevice .cpp file, but the application of Cascades always gives me this error. It is one of the functions in question:

  /*!
   * Returns the MAC address of the remote device, terminated by a null character (\0).
   */
  char* BluetoothDevice::getAddress() {
  
      // Holder for results
      char address[18];
  
      // Perform the check
      int res = bt_rdev_get_address(mDevice, address);
      if(res != 0) {
  
          //TODO  Query failed, pass up error
      }
  
      return address;
  }
  

  Any suggestions?

  Hello!
  I suspect that the NDK functions can be linked only dynamically. Only the .so files are available.

  Try adding
  LIBS +=-lbtapi
  the file .pro of application using the library.

• Error occurred when using the compiler CAP

  I developed a J2ME MIDlet program that can run on the mobile phone. Now, I want to run it on the BlackBerry. I tried to use the compiler CAP to change the .jad and .jar format .cod files. However, he returned the following error message.

  Error! : offset of field too big for: cmdJobDetailGoToTop

  It should not be a java error.

  Someone has seen this before and how to solve?

  Thank you very much

  This error indicates that the class containing the data member cmdJobDetailGoToTop has too many data elements of members where the upper limit is 512 words.  It is worth noting that the number of double and long for two words in this upper limit.

  Finally, the members of the classes of database would contribute to this indictment as well.  To resolve this problem, you must reduce the number of data items in this member.

• Violation of page protection - error get by using the custom plugin

  https://Apex.Oracle.com/pls/Apex/f?p=63937:1:

  The app link.

  Identification information

  -TINO

  [email protected]

  -test123

  When I try to send a page using the normal text field, he's fine. But when I use my custom plugin it throws error PPV.

  You can see the plugin code in the shared components of the application.

  Application is called theme MDL.

  
  

  There also may be problems with my page template but I doubt since the ordinary questions works very well.

  
  

  I developed this on 4.2.6.
  

  Incredible.
  The problem is that the plugin was wrapped with

  As soon as I took it, it could submit its value.
  It's funny how I had no idea how fix it, but as soon as I saw you talking about form I knew what to look for.

  It would be cool to know why this happens.

  Thank you!

• 404 error when you use the button «see more»

  Since the beginning of Adobe Stock in August 2015, I never had the "Show more" button work properly when previewing of images. Can I use the options for most of this series, more of this model and similar images, but see button more still records a 404 error screen. At this point, I completely close my browser for Adobe Stock to reset.  Any suggestions?

  Hello

  Please see the links below for help:

  Error message 404 after the first page of every search. It's driving me crazy that I really need pictures!

  Has thrown two licenses-error 404 #92395577 kamimi

  Hope this helps!

• Error 16 while using the applications in the suite Adobe CC 2015...

  Error 16 while using all the apps in the Adobe CC 2015 suite, it is installed via drive Application Jukebox, I have administrator rights on my laptop and have tried the solutions of permissions on the Adobe support site.

  Completely blocked as to why he suddenly not working.

  1A tried to change permissions on folders of PCD SLstore as intructed.

  2 tried to run with administrator rights.

  3. I tried uninstalling and reinstalling.

  Other help would be great, thanks.

  Error 16 corresponds to the file permission issue and the steps mentioned in the link I provided are useful in some cases.

  In this case, we should try to assign permissions to all of the Adobe directory. Please follow the steps as mentioned below according to your operating system.

  Mac

  1) navigate to the following locations and assign all permissions to the adobe folders to the current user. To navigate, open finder and click on going in the bar on then click goto... type/library/application support of / and then click OK.

  (2) to assign the authorization right click on adobe folder and click on Get info... A window will open. Then click on the lock symbol to allow editing. Then click on sign + to add your user name. Then change read only to read and write. Then click gear icon on the bottom and click on apply to the elements included and click ok...

  Windows

  1) navigate to the following locations and assign all permissions to the adobe folders to the current user.  (Right click on adobe folder select properties then click on the Security tab, click on edit and select current user, that you are connected to, select full control, click on apply and then ok)

  C: / / program data (to view hidden files to see this folder)

  C: / / program files 86 x files / common

  C: / / program files x 86.

  C: / / program files common files

  C: //program files.

  (2) try to run the adobe application

  change to the authorisation should look like image below

  

• get the error when you use the TRIM method in the collections

  Hi Experts,

  When you use the TRIM method I get below error. I make any mistake here?

  DB: Oracle 11g

  SQL > declare

  2

  emp_tab of type 3 is the employee table % rowtype index directory.

  4 l_emp_tab emp_tab;
  5

  6 start

  7

  8 select * bulk collect into l_emp_tab of employees;

  9 l_emp_tab.trim (5);

  10 dbms_output.put_line (l_emp_tab.count);

  11

  12 end;

  13.

  l_emp_tab. Trim (5);

  *

  ERROR on line 9:

  ORA-06550: line 9, column 2:

  PLS-00306: wrong number or types of arguments in the call to 'TRIM '.

  ORA-06550: line 9, column 2:

  PL/SQL: Statement ignored

  Thanks in advance for your help.

  See you soon,.

  Suri

  For PL/SQL collections "index by" you cannot use the TRIM function. If your collection statement excludes the portion "index of...» ", then you can.

  Gerard

• Runtime error in workflow using the API Web service with a VC:VirtualMachine parameter

  Hello

  I took the example for the execution of a workflow using powershell via the site Web of Joerg Lew Web service API and changed to pass an input parameter to the name of the Virtual Machine.

  I have no error in powershell, but when I check the events for the workflow in Orchestrator I see it failed with the error "Validation error for the parameter"vm". It's using out of the box "Start virtual machine and wait" stream  Is a problem with a virtual machine name is paid as a string? I tried to use the full name of the virtual machines and the ID.  I have provided the code below.  Can someone help with how to get this working?

  $vcoWS = new-WebServiceProxy-VCO, VCO - Namespace - Uri of the class http://192.168.1.65:8280 / vmware-vmo-webcontrol/webservice? WSDL

  $workflows = $vcoWS.getWorkflowsWithName ("Start the virtual machine and wait", "vcoadmin", "vcoadmin")

  $workflow = $workflows [0]

  # print the input parameters

  $workflow.inParameters

  # generates the table with input parameters (WorkflowTokenAttribute - objects)

  $inparams = @)

  # fill in the table, an entry for each input parameter

  $inparams += new-Object - TypeName VCO. WorkflowTokenAttribute

  $inparams [0] .name = "VM".

  $inparams [0] .Guy = "VC:VirtualMachine."

  $inparams [0] .value = "vm-113.

  #... turns on and off (use $null on $inparams if the workflow has no input parameter

  #... und implement

  $workflowToken = $vcoWS.executeWorkflow ($workflow.id, $inparams, "vcoadmin", "vcoadmin")

  
  

  Thank you

  David

  Hi David,

  > game $inparams [0] = "VC:VirtualMachine".

  This means that the type of entry for this workflow is an object of type 'VC:VirtualMachine '. So, passing the name of the virtual machine would not work. The expected value for such an entry is the string representation of an object which, in the case of the vCO is a unique object identifier. The object id unique vCO looks like this:

  dunes://service.dunes.ch/CustomSDKObject?ID= "15.23.34.34/vm-590'&dunesName='VC:VirtualMachine".

  but you don't need to know this (technically, if you know the ip address of the vCenter and the id of the virtual machine can be built but is not a recommended practice).

  The right way to find the string representation of the object "VC:VirtualMachine" with the name you need to do a few more things. I'll do the example in java and it should be easy to turn into powershell.

  QueryResult result = vcoWS.find ("VC:VirtualMachine", "xpath:name = \" vm-113\ "", username, password);

  String stringObjectRepresentation = null;

  If (result.getTotalCount () > 0) {}

  FinderResult = result.getElements () FinderResult [0];

  stringObjectRepresentation = finderResult.getDunesUri ();

  }

  Thus, the stringValue should be attributed to the line:

  $inparams [0] .value = stringObjectRepresentation

  Hope it will help.

  Without doubt, Joerg would be able to illustrate this solution with powershell later ;-)