ERROR: Windows could implement < name > (ad hoc)... error saying '"windows could not configure wifi'

Similar Questions

• I get an error message saying 'installation of Windows could not configure Windows to run on hardware on this computer.

  I get an error message saying 'installation of Windows could not configure Windows to run on hardware on this computer.

  Installed the new hard drive on my Toshiba laptop and when I ran my recovery disk, Windows Vista installed, but when I restarted computer I get an error message saying 'installation of Windows could not configure Windows to run on hardware on this computer.

  Help, please.

  Hello
   
  
  Your error message, the problem is probably caused by BIOS or DVD settings or bad cabling to SATA hard drive. Please do the following to narrow down because of the problem.
   
  (a) ensure that all laptops the same hardware, the same manufacturer and the same model.
   
  (b) upgrade the BIOS to the latest version; go into the BIOS and enable "Load Fail - Safe Defaults".
  http://Windows.Microsoft.com/en-us/Windows-Vista/BIOS-frequently-asked-questions
   
  Warning of the BIOS:
  BIOS change / oxide of additional metal (CMOS) semiconductor parameters incorrectly can causeserious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.
  
  (c) If you connect the SATA drives, please configure the SATA controller in compatible mode in the BIOS.

• Windows Setup could not configure Windows on hardware of this computer Installation error on the new hard drive

  Okay so if please bear with me and be patient.  I'm not tech savvy.  I know enough to be able to remove an old hard drive and put another one, but when there are errors, I don't know what to do.

  Here's the situation.

  I have a Dell Studio XPS with Windows 7 installed.  I started having these notifications that my hard drive could be a failure.  I tried everything that I could find to fix it without having to buy a new HARD drive without success.  The current system has a 1 TB Seagate hard drive.  I installed a memory additional bar thingie right after that I got the computer about 4 years ago.  (If someone tells me how to find the properties of real system, I post them if necessary).  Anyway, I bought a new WD 1 TB black disk hard to install before my old dies and loses all my photos and documents, etc...

  I took the old drive yesterday and installed the new hard drive.  I put back the case and turned on the machine.  I put in my Windows 7 installation disc.  He began installing Windows 7... It's completely past the initial screen where it says it to load it and the other... I had accepted the license agreement, but did not have to make a profile and do the work and the reader.  I hope all this makes sense.  Then it pops up this message "installing Windows could not set up Windows on hardware on this computer."  I couldn't figure out what to do from there.  I got the new drive and put the old one back to and here I am. I tried to find solutions to this problem, but I either don't can't make heads or tails out of the responses on the internet or the solution is not exactly my problem.

  Please help if you can!  And if you have any suggestions, please dumb them down so I can understand what to do.  I CAN do if loaded, you just have to not talk too irritable.  Laughing out loud

  Thank you in advance!

  Maybe not...

  The Windows installation is not happy about something, and since it gets at least started which is a good thing, but your installation problem can not really be with Windows - perhaps something about Dell hardware or your 1 TB HARD drive.

  I looked at your system and found this article that you can read to see if it sounds like your original question:

  Windows Setup could not configure Windows on hardware on this computer.

  http://www.Dell.com/support/article/us/en/19/SLN293812/en

  Since Dell has written an article for help on this subject, it means they've met enough times to take the time to compose the article and put it on their WWW site (but, they say, it is a possible resolution).

  Could you take the issue in the Dell online community where experts hang out (especially your amber light).

  Another good place for support is www.bleepingcomputer.com where there is a similar topic as your question (except Vista) on a Dell and a new disk of 1 TB (also a Seagate) and Dell ideas did not work, but someone else has found a way to fix it:

  http://www.bleepingcomputer.com/forums/t/453378/installation-fails-to-complete-on-new-HDD/

  The bleepingcomputer for your error message search reveals other areas and people who have got things to work in different ways, then it is perhaps another place to look for ideas.

  If the installation still fails it would not hurt to do the BIOS setting and see if things are getting longer, and since you are going to write the current settings before proceeding with the adjustment you can always cancel the adjustment if things get worse.

• Replacing hard drive, made restoration of the factory, get the message error "installing windows could not configure windows to run on a hardware on this computer."

  OS = Windows 7

  Computer = Gateway FX6840
  Media = gateway recovery media
  Hard drive is set to AHCI in BIOS

  I started meeting with S.M.A.R.T. errors.

  I backed up my data.

  I replaced 1 TB Seagate original with a new 2 hard drive to Seagate Barracuda SATA STBD2000101. Computer is equipped also is from the factory... no additional or modified facilities.

  I tried to restore Windows 7 from the rescue of the disks created with the "Gateway Recovery Management"

  Windows copying files over, the machine restarts, it installs the devices, then it stops at the "installation program starts services" and a window opens with the message "windows Setup could not configure windows to run on a hardware on this computer.

  I can't apply the Article ID: 2466753 because the process of restoration of the plant seems not provide an option to load a driver .

  Any help would be appreciated... Gateway is only interested to collect money.  They have no interest in serving the poor suckers who buy their products (computer is 2 years old so it is out of warranty).

  Thanks for the reply.

  Fortunately, I solved the problem myself (after 19 hours of stress).
  The problem is that the recent hard disk has something different that no longer ages and makes pre-service pack 1 (SP1 solves the problem) versions of Windows 7 incompatible. My set of recovery disks have been created the day I bought the computer, which had no windows updates installed at the time.

  There is an "easy solution" on the Microsoft support site: http://support.microsoft.com/kb/2466753/en-us

  Unfortunately, their method works only if you have a Windows 7 installation disc, which does most of the people who buy computers pre-built manufacturers. Essentially, the solution is to install SP1 from a disc when don't give you the possibility to load drivers during installation, an option that the gateway recovery disks.

  So I thought that, theoretically, if I use my recovery discs to get a clean install on a hard drive that works, then use windows update to get updated (or at least to get SP1), and then make a set of NEW recovery disks (using windows backup: start > all programs > maintenance > Backup and Restore), I should be able to use these discs to install the new hard disk.

  It worked.

  So for someone else who has this same problem with new hard disks, I hope that the above is easy to understand. If not, ask someone else more savvy and show them this thread. Do not forget that at the end to create new recovery disks, it will ask you if you also want to create a 'system' repair disc. DO THIS! This is the disk that you need to start from when you are ready to install.

  Also: If your new hard drive is bigger than the one that you have created the new recovery disks, the partition on your new hard drive (once everything is installed) will be the same size as the one that you have created the records on. You will need to use a kind of editor of score for re - size. I recommend Gnome Partition Editor. http://www.gparted.org

  Burn gparted Live CD and him, resize your partition, and you're done (google for more in-depth instructions).

  Thank you, theloungelizardK, for the offer on the ISO, but I don't need. :)

  Eastan - ITF

• Windows Setup could not configure windows to run on a hardware on this computer

  HP Pavilion Sleekbook 15-b023cl

  I tried to install Windows 7 on my computer for the last day and after several attempts the same error message. It is said: "Windows Setup could not configure windows to run on a hardware on this computer." How would I go about fixing this problem?

  Thank you

  Hello:

  I'm not sure that there is a 'one size fits all' answer to this problem, if you google the error.

  The most common solution is to try to install the SATA driver.

  Here is the link to the SATA drivers you need for your model. Download and extract to a usb flash drive.

  First file listed is for 64-bit operating systems.

  https://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&DwnldID=22194&ProdId=2101&lang=eng&OSVersion... =

  Use the Drive Options - Advanced method to install and then select the option load a driver.

  If you check the box, only the compatible SATA driver is selected.

  See if it works.

• Pavilion dv7: Windows Setup could not configure?

  Hi guys,.

  while trying to re install Windows 7 on my laptop recently cleared after the installation an error appeared with "installation of windows could not configure windows to run on a hardware on this computer" If someone could help that would be great

  See you soon

  You are the very welcome.

• Windows could not configure one or two components of the system.

  I get this message after completing my update, Vista Home Premium 64 Vista Ultimate 64. All solutions?

  Hello

  1 you have a Windows Ultimate Upgrade disc, a complete edition of the full Windows disk or a Windows Anytime Upgrade disc?

  2 - is Windows XP or Windows Vista already exist on the computer before you install Windows Vista Ultimate?

  Currently, I suggest referring to the following troubleshooting article and thread:

  Windows could not configure one or more system components

  http://forums.Microsoft.com/technet/ShowPost.aspx?PostID=2409427&siteid=17

  Error message when you try to upgrade Windows Vista to a more advanced version of Windows Vista: "Windows cannot configure one or more system components to install Windows, restart the computer, and restart the installation.

  http://support.Microsoft.com/kb/946078/en-us

• 8024A 000 - Windows Update code does not work and "installing Windows could not configure Windows to run on a hardware on this computer" for Vista64 reinstall

  I have a HP Pavilion Elite e9180t PC comes with Vista Home Premium 64-bit.  I had the hard drive (Seagate/Barracuda 7200, 750GB) SATA to go over me (after the expiration of the warranty of course) so I replaced it with a WD Caviar Green 1 TB drive.  When I rebooted the news of recovery disk to the new disk, VIsta worked but Windows Update does not work and I get A 8024, 000 error Code.  To worked with Microsoft to try to resolve that (never made), I am frustrated and all saved just reinstall Vista.  When I try to reinstall Vista, I now get the message "installing Windows could not configure Windows to run on a hardware on this computer."  The installation progresses up to the stage of upgrade (a final) then I get error and it puts everything back the way I started.

  The only thing I changed hardware wise is the hard drive, so this error message seems silly because Windows runs on this material.  I even double checked that Vista is always enabled.  Anyone out there have any ideas?

  I have a HP Pavilion Elite e9180t PC comes with Vista Home Premium 64-bit.  I had the hard drive (Seagate/Barracuda 7200, 750GB) SATA to go over me (after the expiration of the warranty of course) so I replaced it with a WD Caviar Green 1 TB drive.  When I rebooted the news of recovery disk to the new disk, VIsta worked but Windows Update does not work and I get A 8024, 000 error Code.  To worked with Microsoft to try to resolve that (never made), I am frustrated and all saved just reinstall Vista.  When I try to reinstall Vista, I now get the message "installing Windows could not configure Windows to run on a hardware on this computer."  The installation progresses up to the stage of upgrade (a final) then I get error and it puts everything back the way I started.

  The only thing I changed hardware wise is the hard drive, so this error message seems silly because Windows runs on this material.  I even double checked that Vista is always enabled.  Anyone out there have any ideas?

  Hey GMPete

  some posters have reported problems when replacing a drive hp etc. with a hp motherboard not provided player etc.

  I suggest tha contact you hp because it's their recovery process you use

  at the below link HP support forums

  http://h30434.www3.HP.com/

  link below is for direct hp support contact us

  http://welcome.HP.com/country/us/en/contact_us.html

  Walter, the time zone traveller

• Windows Setup could not configure windows to run on this hardware

  I am trying to install Win 7 on a HP Pavilion dv6-7012tx laptop. He brings Win 7 by default. I installed win8 once. Now I can't reinstall win7 on laptop in May. He tried to install Windows 7, but when the computer restarts and tries to complete the installation, I get the following error: "Windows Setup could not configure Windows to run on hardware of Cet_Ordinateur."

  

  My laptop configuration:

  By default the operating system: Win7

  Processor: Intel 2nd generation Core i5

  GPU: NVIDIA GeForce 630 M

  Hard disk: 640 GB (SATA II)

  RAM: 6 GB DDR3

  Hello:

  If you use an ordinary W7 installation DVD and use no recovery disc, the most common cause of this error is the lack of SATA drivers.

  Download and extract these files on a usb flash drive. First file listed is for W7 64 bit.

  https://downloadcenter.Intel.com/Detail_Desc.aspx?agr=Y&ProdId=2101&DwnldID=23060&Keyword=Intel+Rapid+Storage+Technology+(Intel+RST) & lang = fra

  Plug the flash drive into your laptop and start your installation of W7 DVD.

  When you get to install it now click on that and click the option advanced player options.

  Then choose load a driver.  You should now see all the sata on your USB drivers.

  You can check a box and it will include the compatible sata driver to install.

  Proceed from there, and I hope that will install W7.

• "Installation of Windows could not configure windows to run on a hardware on this computer."

  I recently released and bought 4 hard to present itself as a raid 10 disks, now I use my motherboards onboard fakeraid an ihc10r. The cables are fine and when I try and install windows 7 (64 x pro) on each disk with raid and ahci disabled in the bios, windows installs fine. Now when I raid raid 10 disks windows install can see the drive and even then, I load the drivers just to be sure that iastor.sys etc. (I tried with and without) is the same every time after the first reboot, I get about 10 minutes and 2 minutes after the resolution of the screen is adjusted BOOM "installation of windows could not configure windows to run on a hardware on this computer."

  First of all, then someone please help me get windows installed on my raid?

  Second, microsoft, your error messages leave much to be desired, it does not yet add a message in the Setup error log.

  EDIT: Forgot to add that I did a memtest and it happened, I also have the piece of garbage jmicron on my MB off the power. In addition, the facility produces when the SATA controller is in AHCI mode, BUT not in raid mode.

  Seems to me that if the software/driver is not compatible Windows 7. Also if any of the readers have reminants of your installation for each individual unit, Windows 7 may not be able to deal with formatting during the installation process. Try to download CD bootable diagnostic of the manufacture in car and do two things.

  (1) check each drive individually for issues.

  (2) wipe the drive (WD can for example remove the first and last part of the training which completely removes the MBR and other reminants for the final result is the drive looks like you just removed from the box and plugged in for the first time.)

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.

• I uninstalled flash on my mac now youtube videos will not play. the error says safari does not recognize the video formats available.

  I uninstalled flash on my mac now youtube videos will not play.

  the error says safari does not recognize the video formats available.

  Reinstall the Flash Player... Why did you remove it?

  Barry

• HP dv6 7214tx: windows Setup could not configure windows to run on this hardware

  Hello

  I know it has been posted similar problems before, but I still can't get on my instalation.

  I came to this point: during installation PROCESS, almost at the end of this message pop up "'WINDOWS Setup COULD NOT CONFIGURE WINDOWS TO RUN on THIS COMPUTER HARDWARE".

  My PC is: ENVY dv6 7214tx

  3rd gener. Intel Core i7-3630qm

  processor 2.4 GHz

  1 TB HARD DRIVE

  8192 MB DDR3 SDRAM

  Blu - ray optical drive

  Windows 8

  NVIDIA GeForce graphics card

  WLAN & Bluetooth

  I changed boot to the DVD - ROM option, SUPPORT of LEGACY enabled, disabled SECURE BOOT.

  What it might useful to you guys, it's the actual installation takes apx. 5 hours, then he came to the point of pop up window mentioned above.

  Do you have any suggestions please?

  Thank you very much

  .. .also even if this driver has been loaded to the top, another window pops up and says smth like "the driver is not signed, and it might not work.

  However, I let it install... I'll see

• HP Pavilion dv6-7028tx Enterta: Windows Setup could not configure windows to run on this hardware

  As I tried to reinstall win 7 on my laptop HP Pavilion dv6-7028tx, the competition, Enterta I received this message by win7 saying that «windows Setup could not configure windows on this computer hardwear»

  

  I did some research on this issue, it seems to be the lack of SATA drivers on my computer.

  Could you please tell me which intel SATA driver should I install to fix the problem?

  If this method does not work, then please can you me how to change the hard drive in AHCI or IDE BIOS setting?

  Thank you very much

  Hello:

  You cannot change the drive controller setting in the BIOS on any HP laptop consumers made in the last 5-6 years.

  See if it works...

  Download the drivers from this link below (first listed file - 64-bit).

  https://Downloadcenter.Intel.com/Detail_Desc.aspx? AGR = Y & ProdId = 2101 & DwnldID = 23060 & keyword = Intel + Rapi...

  Extract (copy) the files on a USB FlashDrive without all records.

  With the flash player and support installation of W7 in the machine, boot from the installation of W7 media.

  After selecting the install now option, select the training - Advanced menu, Options and select the option load a driver.

  You should now see the storage driver files listed.

  If you check the box, it only includes the compatible driver.

  Follow the prompts and I hope, will install W7.

• Windows 7 cannot complete installation, halfway, it stops and gives me the message "windows Setup could not configure windows for the hardware on this computer.

  Windows 7 cannot complete installation, halfway, it stops and gives me the message

  "windows Setup could not configure windows to run on a hardware on this computer.

  If you have compatible hardware and your computer still stops responding, disable any unnecessary material. Remove (USB) universal serial bus devices. Remove or disable network cards, sound cards and cards of the series; and then restart the installation.

• Windows will not configure my computer from recovery disks...

  I have a HP desktop computer and my hard drive failed.  I bought a new hard drive.  I tried to reinstall windows on the new drive using the recovery discs, I did when I first bought my computer.  It goes through the process of formatting and installation. Start Windows configure my computer.  After a few minutes, I get a message box saying "Windows can not configure your equipment for this computer."  When I click on the 'OK' button, my computer restarts and the process begins again. What should I do to make this work?

  Hello

  This problem occurs because Windows Vista cannot distinguish between ambiguous hard disks.

  In versions of Microsoft Windows Setup that are prior to the installation of Windows Vista, the hard disks are marked with distinct values to distinguish them. However, this method of distinction between the drives is no longer supported due to the risk of corruption of data on hard disks.

  • You have more than one hard drive connected to your computer?

  You can check this link:

  Error message when you try to install Windows Vista on a computer that has initialized the hard drives: "this computer's hardware can not supported booting from this drive.

  http://support.Microsoft.com/kb/925481

  Please post back and let us know if it helped to solve your problem.