Similar Questions

• Problem reading the PXI-2503 channels above 23 in mode 1 wire 48 x 1 Mux on Linux

  I can't get the above relay stations 23 in mode 1 wire 48 x 1

  % nilsdev | grep 2503
  OR PXI-2503: "Dev1".

  The topology is set on "2503/1-Wire 48 x 1 Mux ' via the following API, using the 'Dev1 '.

  DAQmxSwitchSetTopologyAndReset (device, topology)

  In theory this means there are 48 relay individual that can be read, however, fails the following:

  SwitchName = "/ Dev1/ch47.

  DAQmxSwitchGetSingleRelayPos (switchName, & pos)

  The error returned is:

  DAQmx error: relay name is not valid.
  Relay name: ch47

  State code:-200202

  who is

  #define DAQmxErrorInvalidRelayName (-200202)

  I can't get the relay station for foregoing relay 23 (/ Dev1/ch23)

  Which is the expected behavior, or is there a hardware or driver problem?

  When you use this switch in "1-wire" mode, we break essentially each (+) / (-) pair in their own channels.  Since this topology uses switches bipolar, only throw which individual terminals cannot be activated independently, another switch is introduced in order to decide which side of the switch is consulted at this very moment, (+) or (-).

  Instead of having 48 simple jet unipolar or bipolar, we have 24 bipolar single jet and two-way to decide what polarity we are referencing a single pole.  You can still use this topology in mode 1 wire 48 x 1.

  To switch manually using relay DAQmx controls, you need to specify the channel switch and polarity as Maggie mentioned.  When you call ' DAQmxSwitchConnect/Dev1/ch47/Dev1/com0', the driver knows that he has to close the relay 24 ch in more 'HLSELECT' AND "1WIRE" route only positive (effectively ch.47).

  The document NOR switches help contains a more detailed explanation of the topology if you access devices > NI PXI-2501/2503 >

  1 wire 48 × 1 Multiplexer topology.

• Problem with installing Laserjet P1102W - Ad-Hoc - can't change mode of Communication of Ad Hoc

  I have a printer HP Laserjet P-1102W which was installed in Ad - Hoc mode for a short time.  The unit can, however, connect via USB and works very well in this mode, but I want to use it as a Wifi unit with my router and the APs. The unit has a 20130703 firmware datecode. I need to reset the mode of communication out of the "Ad Hoc" mode.

  With the printer is NOT connected through the USB port and holding down the 'X' button to print the "Self Test / Configuration of the device"sheet shows that the status = not connected. " The MAC address displays address 12 characters, the IP address is 0.0.0.0, as is the subnet mask and the gateway. The "IP configured by Hand with the server DHCP/BOOTP = 0.0.0.0 =. The 802.1 b / g Wireless Status = Enabled and the Communication mode = Ad Hoc, SSID = HP4FA96D with authentication = None (open).

  I tried to reset the unit by pressing down the wireless and 'X' buttons located on the top of the machine, but this action does not change the mode of further Ad Hoc communication. I looked through the USB print driver in Windows 7 Pro, but can find no access to wireless settings, and as the camera doesn't have an IP address, I can't access the built in web server.

  Any suggestions on how to completely reset the unit so the Mode of Communication is NOT "Ad Hoc"?

  Concerning

  IT IS FIXED - READ BELOW:

  After trying the patches recommended by other users, download the latest firmware, the driver more current and also help in the HPPSdr.exe of the HP program, making a unit restart by pressing both buttons when the device has been propelled to the top (this is only a partial and not completely reset reset) the unit would not clear the AD - Hoc mode and return to the wireless infrastructure mode.

  The last step, I tried (without the help of HP or the community) was to find the original disc of 2009 and first install it like a USB connected printer. If successful, then a second set with USB cable attached as a wireless printer. It helped me finally change the settings DHCP wireless, assuming, SSID, etc.. Once completed, and unplugged the USB cable, the printer now works as a printer wireless assuming with my router and access points.

  We have NOT ALLEGED on HP support pages for this printer trying to use older software install the disc and make a several step installation - shame on HP!

  The community of HP came with some good ideas, suggestions did not fix of unfortuantely this problem. The printer is out of warranty, so HP Corp. would NOT  provide any help (by e-mail or otherwise) unless I used either the HP community or pay them $24.95 for once call phone support. It seemed stupid to pay 25% of the new value of the printer four years ago.

  Given this bad experience with the lack of support for current HP products which exceeded their warranty period, I can't recommend HP products to my clients or friends. Shame on HP for this contempt for their customers!

  Peter

• Cover my 600EX-RT flash LINK is still red in slave mode

  Hi everyone, I hope someone can help me here.

  I got my Flash Canon & T5i recently, these two works great when the flash is mounted on the camera, but when Iam using the flash in the mood of the slave with the camera the cover link turns red indicating no connection between both & do not come to green at all, here are my settings:

  T5i camera:

  Flash shooting Enabled

  E - TTL II measuring device to assess

  Built in flash set to Cust wireless

  Wirless Func value for the two flash fires (on camera & external)

  Shooting defined group at ALL

  using Channel 4 for communication with flash

  Flash 600EX-RT:

  Wireless Radio slave

  ETTL

  Channel 4

  Group A

  How can I get both to work via the wireless radio signal, please help thank you.

  600EX-RT can work wireless or via radio - or - optical trigger.

  The native ability to the _only_ T5i is to trigger an external flash via optical... not radio.  To do radio, you must either add the camera ST-E3-RT trigger... or put another 600EX-RT flash camera to act as the master of the radio.

  You can, however, pass the 600EX-RT in 'optics' slave mode  To do this, hold the link button until the screen backlight is yellow (not green) and the symbol in the upper right corner shows lightning (not the antenna of the radio).  The link light goes out in optical mode (since there is no radio activity).  Also the Red accent-assistance LED beam will be impulse/Flash on the front of the Flash to tell you it is active (you can turn off if it's distracting.)

  Note that perspective requires line of sight.  Support of the 600 who hides behind the red lens on half lower 600EX-RT.  You may need to rotate the lower part of the 600EX-RT to face the flash on the camera so that it can 'see' the flashover on the device; the flash head rotates so you can always point it where you need - independent how half lower faces.

  Note that (and it's confusing) even if you "disable" the on-camera flash because you don't want there light in your pictures... you will ALWAYS see it fire.  But he fires the flash instructions for the remote control while the shutter is always closed.  The shutter opens, and only off-camera flash goes off (if you have disabled the on-camera flash).  All this happens so fast that you would think that both flashes have been used for shooting.  Thorough image will reveal that the light of the camera was not present in the shot when the shutter is open.

• Fail to implement channel ports in cisco 3750 and ESXi 4u1

  I have set up a vswitch with a rising and electric connection for multiple VLANs. Everything works fine, when the network admin replicate the configuration in a second network port and set up a port with two interfaces channel all my communication with my network management interface is lost, but the test of the esxi management network is successful.

  The vswitch using ip hash and the use of the pswitch political of the src-dst-ip.

  Thanks in advance for any help you can provide.

  F.F.: This is the configuration of the switch:

  interface
  GigabitEthernet1/0/17
  switchport trunk encapsulation dot1q
  switchport
  trunk mode
  switchport nonegotiate
  channel-group mode 3 on
  spanning tree
  PortFast trunk
  spanning tree enable bpduguard
  
  interface
  GigabitEthernet1/0/7
  switchport trunk encapsulation dot1q
  switchport
  trunk mode
  switchport nonegotiate
  channel-group mode 3 on
  spanning tree
  PortFast trunk
  spanning tree enable bpduguard
  
  interface
  Port-canal3
  switchport trunk encapsulation dot1q
  switchport
  trunk mode
  switchport nonegotiate
  spanning tree portfast trunk
  spanning tree
  bpduguard enable
  
  port-channel-src-dst-ip load balancing

  Take-off of VLANs allowed 4094... the native should not be part of the traffic that will flow on the link...

• Grouping of external midi channels

  Hello

  I'm trying to combine two external midi channels, but it does not work.

  I can put them in the same group, I have check the volume, but it still moves only a fader when I'm not touching her.

  I tried to stack them, but the created VCA group does not send the midi volume information

  Is there a way to do this?

  Thank you

  Be careful with the external MIDI in general channel strips. In the mixer, they resemble other Types of Channel Strip, but they are not. External MIDI channel strips don't "carry" any audio signal, the only signal of MIDI. I guess that's maybe the reason why the Faders group.

  It's a bit of a (misleading) confused situation, because there is no indication in this regard. The other grouping settings, however, work on all the channel strips: editing, automation Mode, Record, color, Zoom, track to hide track.

  Don't use Solo and Mute for groups or external MIDI channel strips, they are incompatible between buttons on the tracks and channel strips.

  Here's the group settings that you can use on external channel strip

  

  Hope that helps

  Edgar Rothermich - LogicProGEM.com

  (Author of "Graphically improved manuals")

  http://DingDingMusic.com/manuals/

  "I could receive some form of compensation, financial or otherwise, my recommendation or link."

• Capsule - save the channel selection

  Hi guys.

  I have Time Capsule 3 to with 7.7.3 firmware.

  If I change 'Radio channel Selection' to 'manual' mode and adjust the channels that I need and press the "Update" button - after devices it still restarts use automatic channel selection. Is a way to fix it?

  Thank you!

  Where do you stand in the world? It is Europe that has this problem.

  And I need to the right of the box model number, as that will include your area code.

  There are tougher laws to prevent people setting illegal channels in your area... so if you put a country with different laws of yours and set a wireless channel that is not legal in your area, the TC will close without applying the changes.

  Apple seems to have anticipated this rule change and still 2 years ago put in work in the 7.7.3 firmware.

  Test it using only 2.4 ghz, then set it to channel 8 as a channel that is legal everywhere... let alone 5 GHz for now... it works?

• Extract single channel DAQmx task

  Hello

  I created a task DAQmx output, which contains two channels.  Is it possible to extract the individual virtual channels of the task to be dealt with by two parallel processes?  I tried to bring out the ownership of channels using a task property node, but then I get the error that the channel is not part of an active task (see excerpt)

  Could someone advise on a better approach, or how to obtain this feature - if that's possible?

  Concerning

  Dave

  Sorry, that VI does not have much sense. You must use a unique DAQmx writing for both channels and 1 sample mode, simply build an array of signals as shown below.

  

• Channel-group is not working (via LACP) between 6624 and 6224F

  Hi everyone, I need help.

  aggregation of links is not working. The following example uses the 6224 switches and 6224f

  6224

  interface ethernet 1/g23
  Auto mode channel-group 1
  Description "Ether_Conection".
  Disable spanning tree
  switchport mode trunk
  switchport trunk allowed vlan add 3
  switchport trunk allowed vlan add 4
  switchport trunk allowed vlan add 5
  switchport trunk allowed vlan add 6
  switchport trunk allowed vlan add 8
  Add a trunk switchport vlan permit 9
  switchport trunk allowed vlan add 10
  switchport trunk allowed vlan add 11
  switchport trunk allowed vlan add 12
  switchport trunk allowed vlan add 50

  interface ethernet 1/g23
  Auto mode channel-group 1
  Description "Ether_Conection".
  Disable spanning tree
  switchport mode trunk
  switchport trunk allowed vlan add 3
  switchport trunk allowed vlan add 4
  switchport trunk allowed vlan add 5
  switchport trunk allowed vlan add 6
  switchport trunk allowed vlan add 8
  Add a trunk switchport vlan permit 9
  switchport trunk allowed vlan add 10
  switchport trunk allowed vlan add 11
  switchport trunk allowed vlan add 12
  switchport trunk allowed vlan add 50

  and

  6224F
  interface ethernet 1/g4
  Description "Ether_Conection".
  Disable spanning tree
  switchport mode trunk
  switchport trunk allowed vlan add 3-6, 8-12, 50-51
  output
  !
  interface ethernet 1/g5
  Description "Ether_Conection".
  Disable spanning tree
  switchport mode trunk
  switchport trunk allowed vlan add 3-6, 8-12, 50-51
  output
  !

  I appreciate your help

  Thank you

  Here are some good articles to read on the GAL.

  http://www.Dell.com/downloads/global/products/PWCNT/en/pwcnt_link_aggregation.PDF

  http://www.Dell.com/downloads/global/products/PWCNT/en/app_note_2.PDF

  Once you place a port in a SHIFT, configuration commands must do to SHIFT and not the port interface.

  Console (config) # interface ethernet g4-5 series

  Console # channel - group 1 automatic mode

  output console #.

  Console (config) # interface channel-group 1

  Console # switchport mode general

  Console # switchport General allowed vlan add 3-6, 8-12, 50-51 the tag

  Console # switchport pvid General 1

  Keep us updated

• Port of WLC 5508 and 4510 - channels

  LACP and PAgP are not based on the controller and it seems that the 4500 series will use no LAG.

  Interface Port-channel10
  Description Port-Channel WLC
  switchport
  switchport mode trunk
  service-policy input AutoQos - 4.0 - entry-policy
  service-policy output OUTPUT-PRIORITY-POLICE-ETHERCHANNEL

  interface GigabitEthernet3/1

  Cisco 5508 wireless controller description
  switchport mode trunk
  active in mode channel-group 10
  point to point spanning tree-type of link
  !
  interface GigabitEthernet3/2
  Cisco 5508 wireless controller description
  switchport mode trunk
  active in mode channel-group 10
  point to point spanning tree-type of link

  I get the error message "lacp not enabled on the remote port..". I removed the 2nd fiber cable and removed the channel group so I can get the WLC online. Any help would be greatly appreciated.

  In order to get the channel of ether to work with the WLC, you must change your configuration of:

  !

  interface GigabitEthernet3/1
  active in mode channel-group 10
  !
  interface GigabitEthernet3/2
  active in mode channel-group 10
  !

  Mode it

  !

  interface GigabitEthernet3/1
  channel-group 10 mode on
  !
  interface GigabitEthernet3/2
  channel-group 10 mode on
  !

  Mode IT is said the switch to Link Aggregation Protocol try and negotiate by using one of two LACP or PAgP control protocols.

  using ONE fits in the configuration guide when you enable the option Cisco WLC LAG.

• Voice App Adobe community

  Is there a channel on these community boards for Adobe Mobile Voice app? The web page declares asks questions on the advice of the community, but I don't see one here.

  When scrolling down there is a text box to enter your question, so that recently answered questions and a link to see all the questions.

  

• Channel used in Rman

  Hello
  
  What is the channel in the RMAN backup. What is the use of the channel in the RMAN?
  
  
  Thanks in advance
  ASIT

  A RMAN channel is a communication pipeline between an RMAN executable and a target or auxiliary database. An RMAN channel consists of a server on the target or auxiliary database session and a stream of data to the unit of backup or vice versa. RMAN console sends commands to the database using this channel, and the session running on the database server executes the command on behalf of the RMAN Recovery Manager.

• Encrypted communication of VIX

  I had a fundamental question on the VIX api.  Is communication between the caller of the API and the encrypted virtual machine?  By example, if I call LoginInGuest will be sent encrypted login?  We use vix on an internal network, but I'm curious nonetheless.

  Mark

  Yes, by default it is encrypted using an SSL session *. However, the certificate that comes with the host is self-signed, so if you care about the man-in-the-middle attacks, you'll want to replace it with something of a signatory of confidence.

  =======

  • It's a little more complicated, based on what VMware product you use with VIX. If Workstation or Player, then no, we just use a domain socket local pipe/UNIX. If it is 2.0 or vSphere Server, then there are two channels (a SOAP communication with the host country, and a TCP connection by open virtual machine), that use SSL.

• HP Photosmart C4780 connects not (wireless) on Mac or wireless network

  Sorry for the long post, but please someone help me!

  I bought my new printer a few days (actually 14th) and began to implement on my MacBook Pro with my Wi - Fi, which is routed through a Linksys router and mainly through my desktop computer (a PC with Windows XP). I used the CD that came with the printer to set it up on my Mac and it has set up the fine by USB, but when I try to set up the wireless, I get the following message:

  "Device not connected: to configure the network settings for the selected device, please connect via USB temporarily." The device can be disconnected from the USB once the network settings are transferred. »

  I reconnected and got the same message over and over again, so I decided to set up on my desktop computer instead. This does not work either and I got the same message on my desk I have on my laptop. Uninstalled on both computers, reinstalled and I STILL got the same message. At this point, I'm about to throw all the electronics in my bath tub and be done with them but on the contrary, I checked (and double checked - and triple checked) my router via my browser settings, fact that I know the SSID and the password and reconnected to the network through my laptop... Once again, the same message. I tried the network installation of push, the installation of the network PIN, I feel I have tried everything! Probably miss me something small, but eyes fresh is always an asset.

  Can someone help me? I printed a Test report of the network so that a Page Network Configuration and settings I received both... if need be, I can post the information from my router, in order to verify to implement, but after two days of trying to implement something that should have taken ten minutes (sometimes) I'm at my wits end.

  Network Test report:

  "Your HP printer cannot find your wireless router. Check our wireless router has power. Make sure that your network (SSID) HP printer name exactly matches your router (SSID) wireless network name. If they do not exactly match, run the installation of the wireless network to set up your HP printer. »

  How to change the network name of the printer to match?

  Summary of diagnosis:

  Wireless on: PASS

  Wireless work: PASS

  Find the network name (SSID): FAILURE

  Security: PASS

  The printer settings compatible with the wireless router settings: does not work

  No filtering: does not work

  Related: Does not work

  Signal strength: does not work

  Other networks detected matching your network name (SSID): does not work

  Detected wireless networks: 1

  Downlink Count: 0

  Channel: Does not work

  Although I was given my SSID (which does not match my home network - but how can I change this?) and my MAC address (I guess for the printer), so I didn't have the IP address of my printer has no way for me to get online to check all the settings! Is there another way to get this IP address?

  Summary of configuration:

  Communication mode: Infrastructure

  Authentication type: open

  Encryption: no

  ______________________________________________________________

  Network Setup page:

  General information:

  Network status: offline

  Type of connection: no

  URL to Web server integrated: http://0.0.0.0

  Firmware Version/Hostname/serial number were all given

  Admin password: not set

  802.11 wireless

  Hardware address (MAC): data

  Status: disconnected

  Port 9100

  Status: enabled

  mDNS

  Status: enabled

  Service name: Photosmart C4700 Series [6 last digits of my MAC address]

  SLP

  Status: enabled

  Microsoft Web Services

  WS discovery

  Status: enabled

  WS Print

  Status: enabled

  PC connected (s)

  Address IP/hostname: (nothing is here) Time since last access (mm: SS): (nothing is here)      

  Number of 802.11 networks discovered: 1

  (my correct information of wireless network is here, including the SSID, Mode (Infrastructure), BSSID, Channel, privacy (RSN), Auth (WPA - PSK), Encrypt (TKIP-AES), Signal and WPS (no))

  Help!

  Did you read this on your Verizon FIOS router? : http://h30434.www3.hp.com/t5/Printer-networking-and-wireless/Connection-problems-with-Verizon-FIOS-Actiontec-routers/td-p/892967

• Device series problems

  Hey everybody,

  I am quite new to labview

  I plugged a device series 232 rs to my computer and installed the drivers for it and all that good stuff. I open hyperterminal and had no problem of communication with the module.

  When I open one of the example screw series in labview, I tried to send commands and I kept getting an error message saying that it had expired.

  BUT

  When I sent the same command 5 or 6 times at the same time IE

  VM 1-0

  VM 1-0

  VM 1-0

  VM 1-0

  VM 1-0

  my module receives the command and functions very well.

  What hurts?

  Hello

  You typed the \r \n characters in "------"Codes display "mode?

  Right click on the channel and select this mode before you type \r \n