Ethernet transfer does not-router E1200
Hello
I recently got a new ISP (single digits), they claim they use the service to transfer Ethernet (T1?). They have 1.5 mb upload and download speed.
They installed a 'box' in which I take an ethernet cable and connect directly to my computer and we have an internet connection. As soon as I try to plug the ethernet cable into my router E1200, internet no longer works. I can access the router, change the settings, but not the Internet.
For a short period of time (1 hour), I had internet to work by changing the static 1 8.8.8.8 DNS and DNS 2 to 4.4.4.4
I turned so the router work after the change of some port forwarding settings, and it never worked again. Even after reverse port forwarding.
Thanks in advance, any help is greatly appreciated!
Danny T
Hello
On the settings page, go to the status tab and check if the router has an IP address. If there is none, I would say to reset the router. Press and hold the reset button for 10-15 seconds using a pen or a paper clip. Then disconnect and reconnect the power cord to the router. Make sure that the modem is connected to the yellow port and the computer to one of the ports numbered or blue.
Log on to the configuration page and check again if your router already has the IP address. If there is nothing, go turn it on to Clone MAC address on the Configuration tab, and then click Clone MAC address before you save the changes. Reboot the router and check if you are online.
I hope this helps.
Tags: Linksys Routers
Similar Questions
-
Ethernet controller does not work on the Satellite L645D-S4030
Basically, I got my windows 7 reinstalled on my laptop due to virus... Now I have a problem with the Ethernet controller does not, I checked my device manager and there is a kind of yellow dash through the icon... Someone knows what is the problem and how can I solve this problem?
BTW, I have a SATELLITE L645D-S4030
Hey Buddy,
Hmm generally if you reinstall Toshiba Recovery disk Windows all drivers will be installed too because the disc contains a picture of the factory settings.
Or you used another drive?Yellow exclamation mark can mean that there is a driver problem and so it would be advisable to reinstall the LAN driver. Follow the link Timox. After the driver is installed, restart your computer and check again in Device Manager. The yellow exclamation point should normally be gone.
-
Easy transfer does not recongize. MIG file
I replaced the drive in my Dell d830. I gathered my files on the external hard drive. When I run easy transfer on "new computer", it does not recognize the file in the box go. I can see it on the disk, but it does not load. Help?
No, easy transfer does not have XP to XP.
Is the old hard drive available and functional?
Have you ever used Windows Easy Transfer to copy the files to your external drive?
If you used easy transfer AND your original drive is no longer available (or dead), you may be able to recover the data, but there is no guarantee.
Microsoft technical support may be able to help--for a fee. Alternatively, you can Google MigRecover Utility. However, I understand that there are different versions of the file creates MIG Windows Easy Transfer, but this requires different versions of the tool (I think USMT4 is for the version of Windows 7 to WET and USMT3 for the version of Vista, but I don't know for you).
Sorry, I have more new and good luck.
PS Si the old drive is not actually dead, your best bet is probably to buy a USB or FireWire external drive box and copy the data directly.
-
Ethernet driver does not work on Dell Dimension 8520 after Windows XP install.
Ethernet driver does not not on my Dell Dimension 8520. I reinstalled Windows XP and drivers, and everything works except drivers Ethernet and those. They have big yellow points to mark by them. Tried to delete and restart, but they come back and still do not work.
I don't see anything for 8520 dimension on the Dell web site. Windows XP for Dimension 8250 drivers are here .
-
Try using the simple transfer of transfer from old pc (XP) user profiles to their new pc (7). Easy transfer does not seem to see through switches. If I have 2 machines in different parts of the plant the application will not be the handshake. What I am doing wrong?
Nothing. The 'old' and 'new' computers must be on the same subnet. You can use the intermediate storage.
-
I horizontal mig easy transfer file and I keep getting a message to select a download file does not work. I recently used the file and had to reformat the hard drive and reinstall vista now easy file transfer does not use these files again
Hi pcanderson,
To better understand the issue, we need the following information:
(a) what is you receive the exact error message?
(b) how exactly you try to run easy transfer?
Please provide more details about the issue you are experiencing for understand us to better the issue and help you solve this problem.
You might want to know
The problems of file transfer
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-file-transfer-problems
Transferring files and settings: frequently asked questions
Thank you, and in what concerns:
Ajay K
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.
-
On Apple TV Ethernet port does not
Model: A1625 (64 GB) | tvOS 9.2.2 (13Y825)
The House has wired Cat5 taken and connects directly to the ISP router. I don't have any fancy network equipment.
I was away on vacation and had unplugged the TV and Apple TV surge protector. I went back home and plugged everything in and powered the TV and Apple TV on and Apple TV connect to the network via Ethernet. At the time the tvOS was 9.2.1. I have the following message:
"Error ".
Your device may not be connected to the Internet. Please make sure that your connection is working, and then try again. "Code:-1009"
I've tried unplugging, reboot, new cables, etc., nothing worked. Apple TV connects via Wi - Fi so I did the software update to bring the tvOS up to date with version 9.2.2 said Apple TV to forget the wireless network and all restarted and it still does not connect. Appreciate any ideas?
Test the specific Ethernet jack that you use with ATV on other equipment, such as a laptop computer.
-
Realtek fast ethernet card does not work on laptop with Vista
My realtek fast ethernet does not work with my windows, what can I do about it?
I have no internet access on my laptop
Go to the website of the manufacturer of your computer/laptop > drivers and downloads Section > key in your model number > look for the latest Vista drivers > download/install them.
The computer you are using now if you have an Internet connection with the other > download / save drivers > copy them into Flash Drive > transfer / install on another computer/laptop.
See you soon.
Mick Murphy - Microsoft partner
-
Ethernet still does not work after update 3.28.2
ElCapitan "Incompatible Kernel Extension... '. "update towards version 3.28.2, but Ethernet does not always work.
Any idea?
A reboot may be necessary.
-
We have 2 iMac and today ports Ethernet on every one of them stopped working. The cable into each of them works (tested with a Macbook Pro) and I still can not work for every iMac with a USB Ethernet adapter ethernet cable. How diagnose or reset these Ethernet ports and get them working again?
Tim
It's weird, we have the same problem, I have mac pro El capitan end 2013. The two Ethernet is no longer detected but seeing liaison is present... It was fine last night and after starting this morning, it does not work
-
Windows 2000 is the network via an ethernet connection does not work.
Windows 2000... CHANGED DIAL UPWARD... FOR ETHERNETI just installed a Lan card so I can connect an Ethernet cable to the router, as I had the OLD DIAL-UP CONNECTION to A TELEPHONE LINE...
but I am unable to connect to the Internet... I checked my device manager and it say's works well... I asked my Internet provider for help on the connection, BUT ILS DO NOT SUPPORT MY WINDOWS VERSION
Can someone please adviseHello
I suggest you to download and install the drivers for the network card and check if it helps.
You can try to get the drivers, go to the manufacturer's Web site and check the version of the windows 2000 drivers.
-
Marvell yukon 88e8040 pci - e fast ethernet controller does not
Hi I have a dell inspiron 1750 that I love to bits and recently put a new drive hard and files recovered, but the above problem keeps arising and does not allow me to connect by ethernet or wireless. Please help guys
If you have installed a new hard drive and reinstall vista, you need to reinstall your drivers. Many drivers may be missing. Go to Device Manager and see what drivers you need:
Access the Dell Support and enter your Service tag (drivers)
http://www.Dell.com/support/home/us/en/19?c=us&l=en&s=DHSMarvell Driver Downloads
http://www.Dell.com/support/home/us/en/19?c=us&l=en&s=DHSChoose your platform and enter the partnumber.
-
Downgrade from Windows 7 - driver interface (ethernet) NETWORK does not!
I bought the HP Envy 15-j030us portable and QUICKLY retired the suicidal call error Microsoft Windows 8. Everything is ok except my ethernet driver HP does not work.
The driver has been installed but there is a problem of access to materials or loading the driver, idk.
In Device Manager, it is recognized as a Realtek NIC but does not correctly install the software. When it is plugged in, two activity lights are flashing but there is no evidence of a network. The taskbar displays only the ORANGE icon wifi available.
I am quite frustrated to Macrosoft to put me there already, can someone please help?
http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?product=5395205&LC=en&cc=us&DLC=en&lang=en&cc=us
Hello:
You should be able to use all of the drivers W7 64 bit of this professional HP laptop except the audio.
If for any reason the realtek LAN driver does not work since the link above, you can get it directly from realtek to l'adresse--deuxieme file on the list.
Make sure you install the Intel Chipset Installation Utility driver first before moving on if you have not already done so.
-
Ethernet connection does not work after the decommissioning of 10 Windows 7
retruned to Windows Professional 7 of 10. everything seems to be OK except my connection Ethernet does not connect. I can connect wirelessly. Windows troubleshooting tool does not resolve the problem.
How can I get the adapter to work?
Go into Device Manager and uninstall your wired NIC. do not remove the drivers. Right-click on the name of your computer (above) and select "Search for hardware changes." This should re-install the drivers for the network card.
HTH
Ron
-
Blind transfer does not not for third-party phones
Hello
I use CUCM 10.5 and Cisco and Ascom MyCo phones third-party. I just stumbled across a problem where the immediate or blind transmission does not work on the third-party SIP devices. However, the transfer works very well on all Cisco phones. Against the workflow and no calls work but couldn't find anything wrong. Please help/tips.
Hi Anish,
Can check you for 'Calling rerouting space research' on the phone has access to the number you have transferred blind to.
JB
Maybe you are looking for
-
Retrieve the Satellite C50-A570
Hello I have a Toshiba Satellite C50-A570 month passes and the first thing I did was make a recovery disc and then after a few months, I had I have problem with the Windows 8.1-compatible so I decided to remove Windows 8.1 and install Windows 7 Profe
-
I have not used a front Source control provider. My hope is that I don't have to deal with a large learning curve in using the basic features of a source control provider. Also curious is the most popular provider used by LabVIEW developers. Thank y
-
You want to use the gamepad XBOX 360 on Windows 7?
The Xbox 360 controller install and work on the new version of Windows 7 Home Premium?I'm getting a new laptop ASUS G51J-A1 soon and want to know if it works?Kind regards Mariqua
-
I can get a walk through by phone please.
-
Adobe opens not in vista documents
Gentlemen. 1. I have family vista premium and adobe 9 installed in my computer. but my files won't open in adobe. 2. I tried the following, but it did not helpb---> default programs Panel---> associate a file type or Protocol(b) riht click on file go