EU set date and time why?

Similar Questions

• ATV 4 cannot set date and time

  During Setup wi fi passes accepted. Activation of start and the message is - impossible to contact Apple support set Date and time.

  It is not correctly connected to your network

  Make sure that DNS is set to automatic (network - general - settings)

  Try Ethernet

  Make sure that the router has port 123 open (refer to the manual if in doubt)

• Evrytime I connect me, I have to reset my date and time, why?

  Why my date and time do not be saved? Why should I reset each time my date and time?

  Hi NarendraNP.

  Here are three possibilities about why this is happening to you.
  1. The time in the BIOS is not set correctly. Therefore, every time that you start the PC the incorrect time is displayed. To correct, shut down the computer, turn it on and immediately go into the BIOS settings. Check that the date and time is defined, save and exit, then start the computer normally.
  2. The CMOS battery is dead and needs to be replaced. To fix, you have to expose the motherboard and replace the small type CR2032 on motherboard. You can find many videos on YouTube that will show you how to replace a motherboard CMOS battery.
  3. You don't have administrator rights to the computer to change the date and time, or there is a program installed on the computer that locks the system setting changes (an example of a program that does this is Faronics DeepFreeze). The only solution for this is to temporarily disable the program that is to lock the Control Panel, or ask a system administrator set the date and time for you.

  One of these explanations\fixes help it?

• Calculator HP48SX setting Date and time do not work

  Hello

  I use a HP 48SX calculator.

  The date and time is wrong.

  When I put date and time following message comes:

  Catalogue of vacuum.

  I use to set the date and time after orders

  Blue arrow to the right

  TIME

  What's wrong?

  Please help.

  Using this calculator with 48GX it works well.

  Jochen

  Hi!, jochen2:

  Welcome to Forum!

  Example of time... 13.52-> TIME... and press the ENTER key

  

  You can change the shape, to see (A / h, 12/24, m/d).

  

  To change or set a DATE... 08.102015-> DATE... and press the ENTER key

  

• 'RT Set date and time' does not define the UTC seconds

  Hallo,

  I tried to set the time on my cRio 9012 with the function settimeUTC which is used by the vi "the Date and time value. But the second I get home are ADDED to the current time and not defined as the new value.

  Even the vi illustrates this behavior: I've set up a vi time where in a loop (100ms delay) and reread. When I put in local time stop the clock (as expected), but when I put the UTC time the Dungeon seconds on the run...

  Can someone help me with this problem?

  Thank you

  Florian

  Hi Florian.

  After posting your version of LabVIEW, I found an answer to your question:

  The behavior you're seeing is a known bug that has been fixed in LabVIEW 8.5.1. Workaround is to use set local time instead.

  Let me know if you have any other questions.

• Setting date and time for several photos

  Thank you for providing the space for new users and thank you in advance for your help.

  Currently, I'm moving across lightroom and apple aperture/iphoto 5.

  The part of OCD I like to have my library organized, and I noticed that when I transferred my library everywhere he is in a bit of a mess, so I'm currently putting together the library and it cleaning (around 18000 photos)

  Anyway, I almost settled on a folder structure (YYYY/MM - I for the number of photos I have try on the nut until days could be for many - happy to receive Advisor on it also)

  For the most part, the photos have the date and time of the beginning of the digital age (for me from 2006)

  Photos prior to 2006 are in the negative, and I am currently underway with these scanned and imported into the library, I have a lot each month.  Set the date and time from the date of creation, this is where I am running into trouble.

  I looked around the web and various forums without success.

  First of all, I organize the pictures in the correct order.  Then I select the first photo and then select it the remaining photos.  I then select the date/time setting in the menu and select the first option, ajuster to adjust to the new date and time, say on 01/01/1990 to 1200 hours.

  The result I get is the first photo (the photo so good term) 01/01/1990 @ 1200 as the date and time, others have 01/01/1990 Date (if I'm lucky), and the time of jumping around.  Sometimes it wont even change the date time for the remaining photos.

  What I want to achieve is the time even for all the photos when I select a lot, or increment in time by a lump (is to say 1 minute (1200/1201/1202) or 1 second (1200:00 / 1200:01 / 1200:02)) and I seem not to be able to work it to do this automatically, currently, I have to do this by adjusting each photo (some 200 at a time) which is really manual labor)) intensive

  Thanks in advance and hoping an easy solution

  Concerning

  
  Dean

  I have had success using EXIF change of Basepath.com, but is not

  free. There are other publishers had EXIF free that may be useful to

  you. Some are better than others, and all have a learning curve. I suggest

  make a copy of some files you want to change and make a test of some of

  the available candidates. Search for "EXIF editors" and you can see what is

  available.

• shared variables stops when I use RT Set date and time.vi

  Hi all

  I have a problem that I can't solve. I run a project of RT on a PXI-8106 module using LV8.5. I used shared Variables to transfer data to and from my host computer for about 6 months with no problems. Recently I neeeded to the synchronization time RT with my host PC of time (to collect time-stamped data of the target RT) and I decided to use the "RT set time and Date.vi ' both before the beginning of each synchronization test.

  As soon as I started using this vi, I noticed that my shared variables would either stop updating, or slow down considerably (this includes loss of data during the transfer of data between the PXI to host PC with shared variable). I do not receive any errors or warnings from any of my shared variables, and no errors are generated when using the RT set time and Date vi, so im at a loss for where to start. Ive disabled this feature for now and my system works well again, but I want to get this to work because the timestamps generated in the data by the RT system are out and I need a method to synchronize the time with the host pc.
  Any ideas would be appreciated,

  Thank you

  David

  Thanks for the info. I'll avoid upgrading to 8.5.1 at the moment so I'll just remove the VI. Instead, I create a 'elapsed time' timestamp which should do the job.

  See you soon,.

  David

• Setting Date and time HP 7610

  I cannot set the Date & time by using the printer HP printer Assistant homepage > settings > preferences > Date & time.  When I put the date in the calendar and update time, it returns an error "invalid entry" message X.   What else can I try?

  No, it's the new title IE 11 has... so you have two options.  Use a different browser, or you can open the integrated Web server and click on the top right you will see a gear on it and select compatibility settings and add the SAP address (should be there by default), you will then be able to save your settings in the SAP... Let me know if it works for you.

• Automatically set to the Date and time does not

  Date and time settings on my iPad Air set them automatically does not work? When I turn it out it will allow me to choose a city (Knoxville).

  When I turn it on with (location settings) it just turns and turns?

  Any ideas?

  Hello and welcome to Apple Support communities,

  This problem may be caused by a number of things, most often the cause is the device not being able to contact the time server. Here are the instructions from Apple supported for this problem, as well as a link to the appropriate article.

  Follow these steps, after each step:

  1. Make sure you have the latest version of iOS.
  2. Automatically turn on set in settings > general > Date & time. This will automatically put your date and time based on your time zone.
  3. Make sure that your time zone is set correctly. Tap Settings > general > Date & time > time zone.

  If you still have any questions affecting your date, time, or time zone, you can automatically disable in the settings > general > Date & time and manually set the time and time zone. Or contact your carrier.

  The option to enable the value automatically may not be available in all countries or all shells.

  If the time on your iOS device does not go after a sync with your computer, the computer may be time wrong. Check the time on your computer in system preferences > Date & time. You can select "Set date and time automatically."

  Support the Article HT203483

  Get help with the date and time on your iPhone, iPad and iPod touch - Apple Support

  Of course, if the time of your carrier server cannot connect the other option is to manually set the date and time until the carrier server are again available.

  Hope you helps out.

  Kind regards

  Peter.

• International date and time

  Last week, I was in the United States and took a lot of pictures.  Now that I'm back in Australia, Photos has automatically adjusted the time and date of the pictures to what was the time in Australia, not the time it was when I took the pictures.  It's incredibly annoying.  Does anyone know how to fix this please? Thank you very much.

  Hello! I had the same problem. I took photos in Asia, some on them without location data. I imported on my Mac at home in France. And then, something went wrong with the date and time. As I've learned here for photos without location data, Photos uses the time zone of the place where you perform the import. If had imported the photos in the same zone where I took them, everything would have been fine.

  The solution was to select all the photos and then manually set their time zone in Malaysia where I took them. You can do this with "setting date and time" to the 'Image' (or 'Photos' menu, or however, it is called in English).

• Photos do not sort by time when the Date and time are adjusted

  I'm the combination of images of my friends with those friends, using Mac Photo of OS X V10.11.4. Because the dates of our cameras vary, I used "Image, set Date and time" to change the dates of the imported pictures. When the dates and times are adjusted, the photos are sorted by date no time. Added photos changed the given date are sorted at the end, regardless of time stamp. The sort options in the pictures leave much to be desired.

  Where are you seeing this? All the photos are sorted by date/time, the photo has been added to the library - Photos (years/collections/moments) are sorted by date/time pictures

  You can select the photos of interest and create your own album of them and then sort but title ascending or descending or by date

  LN

• The adjustable BB10 Simulator it is date and time automatically?

  I have the installer of BB10 Simulator (10_2_1_2234) and works generally well on my Mac OSX (10.9.2 Maverics) system using VMWare Fusion 6.0.2 (1398658).  Everthing is in the latest versions as far as I can tell.

  However, even if in the settings / Date and time, the "Set Date and time automatically" switch to "On", whenever I start it, it displays the last time I used it.

  I need to manually enter settings / Date and time, turn the "Set Date and time" automatically to 'Off', set the date and time manually, then I turn the "Set Date and time automatically" button return to 'On '.

  My application itself is able to send and receive data over the network.  I can use the "Browser" application to see the web sites.

  How can I do set the date and time automatically?  Y at - it VMWare Fusion setting, I need to change?

  Thank you

  Ed Federmeyer

  If you resume your virtual machine session, the time that the virtual machine has been suspended is used.  If you "Power Off" the simulator it will update it's time to start.

• given the date and time not set when computer starts. also have a problem with typing

  by turning on my computer, sometimes it lights up at all, and then I try several times so that it lights up. When switching on the main screen, it says error due to the date and time not set and puts my computer starts in safe mode. When I am that I then have to set the date and time again. Why this keep happening?

  on my second question that I have is when I type an email or anything, my writing will just jump on another line and start typing in the middle of other sentences. Why is it jump around like that?

  You may have a failed in your motherboard CMOS battery.

  It's a battery power supply NET, size piece that keeps your system settings when your computer is off.

  They cost about $5 to replace.

  http://www.computerhope.com/issues/ch000239.htm

  How to replace the CMOS battery in the above link info.

  See you soon.

  Mick Murphy - Microsoft partner

• How long does take to set up the date and time

  How long does take to set up the date and time

  Less than a minute.

  Settings > general > time zone > set automatically

  If this does not work, try the help in this support article > If your Apple TV will stop to display date and time on startup - Apple Support

• As of the 31 version, why is there still no option of Thunderbird to insert the date and time in the message that you write?

  As of the 31 version, why is there still no option of Thunderbird to QUICKLY insert the date and time in the message that you write?

  Literally, saw this option very well needed - and opportunity-"promise" for three years now, and even if there are only one or two formats that could be used, at least the option is there.

  It seems that only is to bind a Macro, and the tool to Thunderbird and do it this way.

  Joe Rotello
  [email protected]
  Skype: joerotello

  If the installation of the add-on of TimeStamp is unacceptable for see you if there is a related add-on that you that you already might have managed to convince author to add your function. The Add on more for example has many variables that can enter the body of the message that get automatically replaced with the appropriate data when you merge a message.