Event when the image is evaluated or beating Pavilion

Similar Questions

• Hallo why? When I update ios. When the image has finished error itunes and usb

  Hallo why? When I update ios. When the image has finished error itunes and usb

  Connect the iPhone to the computer that you are synchronizing usually with

  and follow the prompts to iTunes on this computer. If you

  do not generally in sync with a computer, you should always use

  iTunes on a computer to complete the update.

• Acquisition of CL crashes when the image is too light?

  I have a strange problem and I can't be sure either the camera or the Board of Directors: basically, in any method of execution, when the image is too light, the acquisition stops and I get a timeout in MAX. It is with a PCIe-1433 and Point grey Gazelle. Blockage of the camera and restarting acquisition works very well. This occurs at any time, that the majority of the image gets to 80% brightness.

  To make things more confusing, this can sometimes be corrected by the passage of cable (the same 5 meters OR cable model, but just another); now, however, I have a couple of cameras that show that all cable and so I need to get it figured out. It would certainly be a problem of camera or a combination and so I contact PMP as well. Anyone has any ideas on this? Thanks in advance for any info!

  I would suspect that your CameraLink cables cannot meet performance requirements for speed of clock and the distance, that you are running. Unlike most new buses at high speed, the underlying mechanism of encoding on the wire for CameraLink has a characteristic resistance to noise (even among his own peers) depends somewhat on the actual data values are transmitted. Since the frame control signals are passed in the same channel as the content of the image itself, if there is some noise/interaction between them on the wire, they could cause problems of behavior on the side of the acquisition.

  If your camera supports the lowering of the frequenency of the clock, you might be able to check that helps the behavior. If it does, I recommend trying to replace the cables with superior quality-those. The CameraLink Committee now has a test of official certification of cables which is very comprehensive. I would say in ensuring that the cables you are using are actually tested for these certification tests.

  Eric

• Intercept touch green application event when the device is locked

  Hi, I'm new to blackberry. What I want is I want to take a key event (green or red button) when the device is locked and do specific tasks in my application that runs in the background if this button is pressed. Is this possible? How can I do?

  Just to be 100% accurate, it is possible for a keyListener (look to the top of the class) to pick up some events even when running in the background.  It can be different events when the device is locked.  Indeed, the events may be different depending on whether the "locked" screen is currently displayed or not. And the entire lot is dependent on operating system level, in other words, the same device running two different levels of OS will possess differently in terms of what keys can detect a listener in the background.

  So if you have a BONE and a specific device, so it might be something you can do, especially if it is an older operating system.  However if you try to create something that works generically, then know that I've tried and failed!.

• How to register for an event when the device is connected to the PC in USB mode or sync

  I develop application on blackberry with phonegap.

  I want to hear event when the BlackBerry device is connected to the PC by USB MODE or sync.
  I saw mediagallery and applications Filemanager showing the dialogue that the application cannot be used when connected to the PC in USB mode.
  I want to display dialog similar to my request.
  Can anyone please help on how to do it.

  I saw blackberry webworks API

  public static Boolean blackberry.system.isMassStorageActive)

  who says if massstorage is active or not.

  But I can't keep on request this API every time. I'm looking for an API that gives me the reminder.

  Can you please help.

  On the side of Java, this can be done by implementing a FileSystemListener and the rootChanged method:

  public void rootChanged(final int state, String rootName) {
      if (rootName.equalsIgnoreCase("sdcard/")) {
          if (state == FileSystemListener.ROOT_ADDED) {
              /* SD Card is available. */
          } else if (state == FileSystemListener.ROOT_REMOVED) {
              /* SD Card is not available. */
          }
      }
  }
  

  I was not able to find a corresponding WebWorks API or API community well, so I think you need to create your own custom extension to implement this feature of the listener.
  https://developer.BlackBerry.com/HTML5/documentation/using_javascript_extensions_1866976_11.html

• Event when the application closes

  Hi *.

  is there an event when the PlayBook application is about to close? I would like to save at this time where the configuration etc.

  Not that I know of.  It will be an event at the level of the AIR that is triggered when this problem occurs, and I do not think that such an event is currently on the Tablet OS.

• How to load something when the image appears

  Hello. I have a load_swf button that does this:

  swf_path = "sample.swf"

  load_swf.onRelease = function() {}

  loadListener.onLoadProgress = {function(target_mc:MovieClip,_bytesLoaded:Number,_bytesTotal:Number):Void}

  info.text = Math.round ((bytesLoaded/bytesTotal) * 100) + "%";

  };

  loadListener.onLoadInit = {function(target_mc:MovieClip):Void}

  info.text = "";

  };

  var mcLoader:MovieClipLoader = new MovieClipLoader();

  mcLoader.addListener (loadListener);

  mcLoader.loadClip (swf_path, swf_loader);

  };

  I want to do without having to press the button. I want to do when the image appears on the screen. Something like OnClipEvent (load) the problem is that I do not know how to convert this code works with OnClipEvent (load), can you help me?

  use:

  swf_path = "sample.swf"

  loadListener.onLoadProgress = {function(target_mc:MovieClip,_bytesLoaded:Number,_bytesTotal:Number):Void}

  info. Text = Math.round ((bytesLoaded/bytesTotal) * 100) + "%";

  };

  loadListener.onLoadInit = {function(target_mc:MovieClip):Void}

  info. Text = "";

  };

  var mcLoader:MovieClipLoader = new MovieClipLoader();

  mcLoader.addListener (loadListener);

  mcLoader.loadClip (swf_path, swf_loader);

• Avoid the display of the Red Cross when the image is absent

  The images from loading user on my web site.
  He can enter 3 images; but sometimes it does that 2.
  When an image is missing, the browser try to find and display a small red cross in the left corner. My concern was to avoid the display of this small red cross when the image is not there?
  I tried nested HTML and PHP code, but it does not work.
  Y at - there someone who can help me?
  Thank you very much.

  Gary,
  Finally, I solved the problem by setting the value of the border to 0. Now everything is OK.
  Thanks again.

• Generate the event when the focus lost

  Hello

  is there a way to capture an event when a textbox control lose focus?

  Thank you.

  Yes there is, just create an event filter button on this control of the chain and when a tab is entered you trigger your (re) load event. Or you can set a keyboard shortcut for this field (such as ctrl-D) to define a group of controls to a default state.

  What are the complications that would keep a button 'Load' of work? Maybe things are too complicated and we need to simplify things a bit.

  Mike...

• Event when the time changes?

  I want to be able to perform a function at an exact time specified by the user. The time will always be an exact hour and minute, so I think that I just need to check once per minute. But, I want it to be just at the point where the minute changes. For example, if a user sets time for '04:30 ' I want the function to run when the clock on the PlayBook goes at 04:30 (preferably as close as possible). But if my timer runs a function listening every minute and it starts between the minutes for example "2:00:30" then he know what "02:01" until he has "2:01:30", exactly one minute after it starts.

  I could run a function on each picture, but I didn't it would be the best way to do it.

  EDIT: I guess the obvious solution for some could be just check once a second, but this really the most effective way?

  Is there some sort of time, or in some other way event listener to do?

  This is not tested, but it might do what you want:

  import flash.events.TimerEvent;
  import flash.utils.Timer;
  
  ...
  
  var secondsTimer:Timer = new Timer(1000);   // 1000 milliseconds or a second delay
  secondsTimer.addEventListener(TimerEvent.TIMER, onSecondsTimer);
  secondsTimer.start();   // start timer
  
  ...
  
  secondsTimer.stop();    // stop timer
  
  private function onSecondsTimer(e:TimerEvent):void
  {
      var currentTime:Date = new Date();  // get current date/time
  
      if(currentTime.getHours() == userSetHour && currentTime.getMinutes() == userSetMinute)
      {
          do something
      }
  
  }
  

• Is there an event when the mobile connections are changed

  Hi, expert,

  I'm looking for an auditor check the following:

  1. when the phone is connected to a mobile network not connected

  2. when the phone is connected to another mobile network (another carrier or wifi) from current network

  3. the current mobile network connection is dropped.

  I found of initailly than ConnectionAttemptLIstener (http://www.blackberry.com/developers/docs/5.0.0api/net/rim/device/api/io/transport/ConnectionAttempt...). I thought I could use it to change mobile network connection. It turns out that I just couldn't. He listens to the event on ConnectionFactory which really is a connection on the connected mobile network.

  Did some research and I could not find any related information.

  So is it possible for me to achieve what I said at the outset?

  You can use a combination of CoverageStatusListener and RadioStatusListener to have access to these events.

  CoverageStatusListener will let you know what type of network access you have access from your coverage (by cell phone connectivity, etc.) WLAN network and which network transports are available).

  RadioStatusListener will let you know when the changes on the cellular network occur as signal changes, changes the base station etc.

  RadioInfo class can also be used to receive information on the current mobile network too.

  Kind regards

• CS6 AIR flash device emulator throws off events when the sensors are changing

  I'm developing an application in Flash CS6 targeting AIR 21.0.0.176 for Android.  I've implemented the NativeApplication.nativeApplication Event.ACTIVATE Event.DEACTIVATE listeners.  These work as expected when the Android device is running standalone or if I am debugging via the interface to CS6 USB. However if I have a deployment on the simulator of premises, whenever I use the Simulator interface to generate a change in the accelerometer or location, the application then receives a DEACTIVATE event.

  It's difficult troubleshooting because on my manager to DEACTIVATE event by stop all the interactive features in the application.

  Any ideas please?

  I guess only the two ways to work with the configuration of the listener. It is not a bug, however, the window of the Simulator is a different application, when you select you have disabled your app, it did the right thing. But in this case, you don't want him to do the right thing, then use the work around.

• Using 5.7 LR on a Mac, how do I file to display when the image import?

  Something has changes on my Mac using Lightroom 5.7. When the import images the file management section does not appear in the right column. Show the other sections (change file name, of the apply during import and Destination). What can I do to recover the management of files, which is necessary to create a backup copy of my images on another hard drive.

  Right click on one of the other section headers. In the context menu that appears, make sure that there is a check mark in the management of files.

• Why size folio remains even when the images are sized down?

  In the constant battle to reduce the size of folio, I found and removed an image of print size wandering (40 MB) and replaced with a 2 MB file but my folio always claims the same size when I see the next update. Any idea out there, why a folio will hang on its size in this case.

  Thanks in advance

  Because we automatically resize the images to 108ppi in the dimensions in pixels of the image container. A 40 MB print image does not pass through to the folio as 40 MB. He'll get sampled down.

  Neil

• Kill the MouseEven.CLICK event when the mouse is held down?

  I studied games on Facebook and trying to emulate mouse events management. For example, in ChefVille, you can click on the objects and drag them around. But if you hold the mouse down you pan all the game environment and when you release the mouse button a click is NOT on the object under the mouse. In my tinkering the click event will be triggered by the release of the mouse button, no matter how many time keep the button pressed. How can I keep the trigger CLICK event if the mouse is held down for a certain period of time?

  I don't know that you can cancel a CLICK event in the middle of what is happening (click = MOUSE_DOWN followed MOUSE_UP), but you can start a timer on the MOUSE_DOWN event and its event handler to set a Boolean variable that can make your event HANDLER function used to decide or not to treat a CLICK event.