Expires on simulated device timer

Similar Questions

• DAQ - mx Simulation devices

  Hello. I just reinstall Labview 8.2 and I do not see simulation devices in Max MAX is 4.2. All I can see cable RTSI. I used to have simulation devices, but I also installed LAbview 2010 before eval. After the complete reinstalled I can't get it back. I tried several times. When I install new DAQmx (I think than 9.1), it installs simulation devices, but then I lose my vi.lib DAQ - mx directory (don't know why).

  Based on the info from NI Labview 7.4 and above should have simulation devices. Any suggestions?

  I use Win 7 64 bit.

  Thank you

  Thank you.  I think that we get no warning because 8.2 supported by Vista, and that's probably just enough good pass install Win7.

• NI 6509 simulation device

  Hello

  My question should be simple enough, but I have not found the answer.

  I have a NOR-6509 card and it should be possible, according to the different tutorial nor helper I've read, to simulate the device using MAX, without being connected to my laptop. The thing that would be very useful to develop portable applications c# on my computer when traveling away from the office.

  "Now with NOR-DAQmx 7.4 or higher, using simulated devices, you can develop, run, and troubleshoot data acquisition applications without going through the applicable material installed [...] A simulated NEITHER-DAQmx device is a replica of a device created by using the option OR-DAQmx Device simulated in the menu create new from MAX to a function or program without equipment. A device OR-DAQmx simulated behavior similar to a real device. Its driver is loaded, and use programs are fully verified... »

  The fact is that I can't do work at the same time, my request - for example, the application of WriteDigPort.exe provided with examples of dotnet 2.0 - and a device of NOR-6509 simulated by a task generated to simulate an output port Dev1/port 0 for example. I have a conflict error.

  I don't really see not how to simply check that my request goes to the value '1', for example, every bit of my virtual Dev1/port port 0 MAX and seeing the lights 'virtual '?

  Ditto for reading: how e chech with a simultaed device that my request is properly read a port that I set to a specific value?

  Thanks much for the reply!

  Hello

  You can read output simulated. The simulated device aims to offer the possibility to start the program without hardware; also with a simulation device, you can check if the syntax of your program is correct and check if the data you write meets the specifications for your motherboard.

  You might find some useful information here:

  http://zone.NI.com/DevZone/CDA/tut/p/ID/3698#toc3

  Kind regards

• drivers for simulated devices of NOR-DAQmx (NI9211 etc.) in cDAQ9174

  I'm trying to understand the three methods of calculating the maximum analog input sampling rate below NI CompactDAQ system

  http://zone.NI.com/DevZone/CDA/tut/p/ID/4320

  Problem 1

  In method 1. Build your physical hardware system or simulate your configuration able & Automation Explorer (MAX) using NOR-DAQmx simulated devices

  Buy using my MAX, I was able to build a simulated chassis cDAQ7192, but the NI 9233 modules or 9215, and NI 9211 is not found in the MAX. do I need special disks for them?

  My MAX is verson 4.6.2f1 and LABVIEW2009.

  Problem 2

  Following the method 2 to use the NI CompactDAQ Advisor, 'Performance of analog to calculate' does not appear upward after you set up the chassis.

  Thanks a lot for your help

  Concerning

  Bing

  Your version of MAX and LabVIEW is not relevant. What is your version of DAQmx?

  After you add the chassis, you right click on it to select "set up simulated cDAQ chassis? I did this and was able to select all the devices you mentioned.

• Is it possible to change the sine wave 'exit' a simulation device?

  I work on a LV collection and analysis VI in LabView that interfaces with a CDAQ-9178 loaded with 9215 modules/a. chassis.  In the Measurement & Automation Explorer, I was able to set up simulated devices that work with my code and I get the sinewave / 5 (?) standard signal noise %.

  However, to really test my application, I need a slightly different sine wave with high frequency (1-10 Hz vs the)<1hz sent="" by="" the="" simulated="" device). ="" is="" there="" anyway="" to="" modify="" or="" get="" the="" simulated="" device="" to="" output="" a="" different="" wave? ="" if="" not, ="" are="" there="" any="" other="" simple="" ways="" to="" simulate="" the="" device? ="" i="" could="" write="" another="" vi="" to="" send="" out="" a="" sinewave="" but="" was="" looking="" for="" a="" more="" obvious="" or="" simpler="" solution="">

  Thank you

  # You need to do is call an of the generating functions of waveform instead of the DAQmx Read. Place inside a case, the declaration or the conditional structure disable is fairly simple.

• Can I automate the creation of a simulated device?

  I see I can create simulated devices OR Max is it possible to automatically create devices of simulations? I want software unit as part of an automated deployment process testing

  Hi Chris,

  Sorry, I thought that the System Configuration OR > LabWindows/CVI function appeared when you install OR-DAQmx (after selecting "Custom"), but it doesn't.

  Here's what you need to do:

  • Configuration of system OR download: http://joule.ni.com/nidu/cds/view/p/id/2613/lang/en (or select from the Driver DVD NOR)
  • Select LabWindows/CVI:
    
  • nisyscfg.h must be installed in %ProgramFiles%\National Instruments\Shared\CVI\include.
  • nisyscfg.lib must be installed in %ProgramFiles%\National Instruments\Shared\CVI\ExtLib\msvc. Note that it need to link against user32.lib as well.

  Brad

• No NOR-DAQmx eligible simulation device

  Hi all

  I am developing an application for a PXI-6132, but I don't have the equipment yet, so I would like to start this with a simulated device, unfortunately when I'm at MAX, I see no device at all to choose, so I was wondering what I can do and I can't wait for material to arrive.

  I don't want to spoil my installations OR so this is the reason why I ask through this support.

  I have attached a few photos on this problem.

  Any ideas?

  I have:
  -LabVIEW 8.6

  NOR-DAQmx 8.7.2

  Thank you very much in advance

  Gozto

  The real is to solve it (I realize) comes to update MAX, I was working with the MAX which was included with LabVIEW 8.6, so I downloaded NIDAQ930f2.exe and it worked.

  Now I am able to virtualize my devices.

  I hope this might help someone with the same question/problem.

  Good day.

• Feature Request - Show client device time zone

  Hello

  I had a few problems recently where knowing what time zone the client machine has the value would have been useful. Is it not possible to show the client device time zone when viewing current user Sessions?

  Thank you

  Scott.

  Hi Scott,.

  The application has now entered in the feature with id request system, TFS 275400. https://support.quest.com/SolutionDetail.aspx?ID=SOL106385&PR=vWorkspace

  David

• How to change the ID of the simulator device?

  You will need to change the ID of the simulator device... anyone can guide me?

  in eclipse, open the configuration to run or debug and select the simulator that you can enter the PIN to use it

• A pack of component allows the simulator device to another?

  I have several packs of component installed in Eclipse. Is it possible to compile a project for, say, 4.2.1 and debugging on a simulator device that comes with, say, the 4.7.0 pack component? Or install a separate 4.7.0 simulator package the only way to do it?

  Enter debug configurations, create a new BlackBerry Simulator. The tab JRE choose JRE Alternative so that you can have different sims for different environments JRE.

• CQI RTD sample.vi with simulation device

  Hi all

  I am student on samples DAQ in labview 2009, I have no DAQ hardware, but I faked 9188 NI and NI 9214 (thermocouple). I want to run 'acq RDT sample.vi' devices with these simulated, but when I run the program it displays error "possible reasons: device to which is attached the sensor doesn't have a source of available internal excitement." Select another device with a source of available internal excitation or provide external excitement. ». However, in the web, it is said that NEITHER 9188 and NI 9214 are available for real-time measurements. What is the problem with that?

  What Jacob said, is that the 9214 is not designed to work with the RTD sensors.  An RTD is a resistance that changes the value with temperature.  A thermocouple produces a voltage proportional to the difference in temperature between the junctions.  A measurement system for thermocouples need measure the voltage and often compensates for cold junction temperature.  A measurement system for RTD must measure the resistance which is generally to provide a current, and then measure the voltage drop.  The 9214 is not a supply for RTD current circuit.

  The specificatioons for the 9214, it seems that it will work with the real time operating system.

  Lynn

• Is it possible to add a simulated device NI DAQmx device or modular Instrument?

  Hello

  I want to simulate SMU 8115 module without hardware. Is this possible? If so can I add the device in simulated NI DAQmx device or modular Instrument?

  HM, these are several very basic questions...

  The controller (8115) is a "full" computer other than housing, power and cooling. At least three components are the chassis, in your case the SMU-1062 q.

  The controller can be managed by a Windows base OS (e.g. Windows 7) or in time real ("RT"). So what you have installed on the 8115?

  In both cases, communication with this additional controller by an external, laptop or PC is best done by Ethernet. You can use different protocols over Ethernet as a TCP/IP protocol based on measurement or using shared Variables OR.

  NEITHER DAQmx is a hardware device driver. The purpose of this is to use a National Instrument based measurement device in a computer. If you want to use a hardware OR your SMU system, it is very likely that you need to have installed on the controller of 8115 DAQmx. DAQmx is available for Windows, as well as regards to the RT

  DAQmx in this case of use don't gives you direct access to the devices in the SMU over Ethernet chassis by * all * external computer. You write an application that will run on the DC 8115 interface (or 'relay) data to your external computer.

  hope this clears things up,

  Norbert

  PS: You should ask your branch to send someone to you... I think a direct discussion with an employee OR should be beneficial to you. Normally, a sales representative is sufficient as a VRP NOR is quite technical.

• USB-6341 not on the list of simulation devices

  I want to create a USB-6341 siumulated, but this model is not in the list of available under devices simulated in MAX X series devices. I don't see in the devices of series X available for the simulation are PCIe devices. I have MAX 4.7, 9.1.5 DAQmx and LabVIEW 2010. I did this on other computers running older versions of the software and saw this device on the list, so there must be a software component that I have installed, but I can't understand what it is. Any suggestions?

  Richard

  Material of the series X USB were not released before DAQmx 9.2; you need at least this version in order to use a simulated.

• Simulator Device.xml file has a tag with an attribute of memory, what are the optional values for this attribute of the os?

  In the Device.xml file, it starts with the tags of the os. Each os has a memory attribute. What are the optional values for the attribute memory?

  Can we really control the memory for the simulators?

  0x85000F03
  0x8C000F03
  0x87000F03
  0x84001503
  0x86001503
  0x04001507
  0x0F001507
  0x0C001404
  0x0D001404
  0x0E001404
  0x0D000D04
  0x16000D04
  0x05001504
  0x07001504
  

  These values refer to specific hardware configurations are simulated.  They should not be changed.

• Can I connect to the internet via the simulated device

  Hi all, sorry for the newbie question - can I use the "Device Simulator" in the 4.6 JDE to develop and test the network management, for example to get HTML page, browsing the internet etc.

  Thank you!

  Udik

  Check the icon 'Manage connections' on your home screen and make sure that all connections are enabled.