ExpressCard for 1394 for D830

Similar Questions

• Best analog input for portable computer device

  I have a Sager laptop and CS5.  When on the road, I would have the ability to import the VHS and other legacy formats.  Any suggestions?

  As long as your willing Sager of a FireWire connector (my other more ancient the fact), or has an ExpressCard for a FW controller card, I strongly suggest the Canopus/Grass Valley ACDV-110, or the big brother of the 300.

  Good luck

  Hunt

• DV4T-1400: IEEE-1394 Firewire

  My Sony camera will only download using IEEE-1394 Firewire

  Is it possible to make the DV4T-1400 accept the Firewire cable?

  There is a white card push. Under hardware it is said: slot ExpressCard/54 card (also supports ExpressCard/34)

  Can I do with it?

  Thank you

  Hello

  Please try a card which is similar to the following map:

  http://www.StarTech.com/cards-adapters/FireWire/2-port-ExpressCard-IEEE-1394-FireWire-card~EC13942

  Kind regards.

• EliteBook 8770w firewire

  Hello, I recently bought an elitebook 8770w (LY562ET #ABU) and use it to write music. I was think Purchasing UAD 2 satellite firewire to use with my DAW, but do not know if it is compatible with my Elitebook. The satellite UAD2 has 400 and firewire 1394 slots in the rear that are compatible with Firewire 800. I was wondering if you could tell me whether or not my Elitebook would be able to connect to the satellite? because I read somewhere that a similar Elitebook model wasn't compatible 800 firewire.

  It has a port... ieee1394a firewire. See the datasheet here:

  http://h10010.www1.HP.com/wwpc/pscmisc/VAC/us/product_pdfs/HP_Elitebook_8770w_Datasheet.PDF

  

  The firewire port is on the right of this photo, and it looks like standard firewire400 for me. There is an Expresscard 54 expansion slot, and you can use an ExpressCard firewire800 to establish the connection. In other words, if you have firewire 800. I gather firewire 400 will also work and there is cable adapter to connect any type of firewire 400 buses to a firewire 800 connection. In other words, I think you can connect the camera to the laptop with a cable. If you can post a photo of the FireWire on your device, I can find you an adapter cable. Here is an ExpressCard for you give a 800 firewire if you absolutely must have that:

  http://www.Amazon.com/Belkin-FireWire-ExpressCard-external-F5U514/DP/B000I20QSQ/ref=sr_1_1?ie=UTF8&QID=1379685573&SR=8-1&keywords=ExpressCard+54+FireWire+800

  It is an Expresscard 34 element, but most Expresscard54 slots can also accommodate an Expresscard34 device. Let us know if you have any other questions.

  If this answers your question, please click the button "Accept as Solution" gray so that others with the same question may easily find it later.

• Satellite Pro L300 - cannot install software for USB 3.0 Expresscard

  I try to install AKE USB 3.0 expresscard to a Toshiba L300 Pro running Windows 7. The laptop recognises the ExpressCard but the software does not correctly install if the unit will not operate.

  Tried the drivers NEC & fresco provided with the unit and also tried other drivers for AKE downloaded fron internet but still no joy.

  Has anyone ever loaded into the software for a USB3.0 expresscard successfully? The laptop will have USB 3.0?

  Any help would be appreciated.

  If the software doesn't install correctly, try to contact the manufacturer of the card and ask for help.

• Satellite P200-1BA - specification for Expresscard

  I want to buy an Express card for my laptop, but I don't see all my specifications of it.

  I think that if I buy expresscard/34pin that fit for her even if I have expresscard/54type in my installed book. Fix?

  Take a look in the user manual, you will find the answer:
  The expansion card slot Express can accommodate two standard module formats; an Express Card/34 and an Express Card/54 module.

  If both types are supported.

• Question about satellite for MAC via IEEE 1394 connection

  Hello

  I have a laptop Equium I have connected to a box of OS x via Firewire to transfer files and use the functionality of the Macintosh to share Internet via IEEE 1394. Someone can tell me why, when I plug the Firewire cable, WinXP detects a new device that doesn't have a driver for the laptop?

  The Firewire device is already installed and seems to be working properly before plugging in the cable.
  Thank you!

  Hello

  Sorry, but I have never tried to connect a Mac with a Windows unit.
  As I know the Mac operation use another file as units of Windows mode.

  Usually, the best way is to use a LAN cable and not a firewire cable to connect the two computers. Firwwire does not support the IP or / and TCP protocols.
  In this case I don't know how the conection it works without all the protocols.
  However try to connect the devices via a LAN cable.

  Please also see this page:
  http://developer.Apple.com/

• Need network adapter 1394 for Portege M500

  Hi people,

  I'm looking for a driver for adapter Net 1394 to one Toshiba M500 running Windows 7 as evaluation, I can't find it anywhere.

  Any help will be appreciated.

  Support Win7 is not always started and maybe you should wait a bit until that Microsoft it out on the market and all laptop manufacturers begin the official support of Win7.
  Until then, you are on your own.

  By the way: Toshiba U.S. offers some BETA drivers. You might find something there.
  See its page for assistance under the http://www.csd.toshiba.com/cgi-bin/tais/su/su_sc_modSel.jsp

  Good luck!

• Drivers for card ExpressCard

  Which driver is necessary to use the ExpressCard slot? I can't find. My Belkin docking station (that I just bought) running on EC does not work (it is not detected).

  slot: 54mm, map: 34mm.

  Lenovo R61i, 8943-DSG, WinXP (downgraded from Vista).

  Thanks in advance for your answers

  My problem is solved. I had never used to express cards and I made the mistake of base. I didn't add it at the end. I felt a bit tough, but I have to press a little harder. What a shame!

  Séverine, thank you very much for your help.

• Thunderbolt ExpressCard adapter for ExpressCard-8360 card

  Hello

  ExpressCard card slots become rare on laptops these days... so I was thinking about an option of plan B... like having to assume OR have nothing until their marketing announce something exists (which is fair enough on R & D / Marketing / strategic plans etc.)

  If someone has already tried a bolt of lightning to ExpressCard adapter for example https://secure1.sonnettech.com/product_info.php?cPath=139_140&products_id=483&osCsid=4fcf0e26d322d5b...

  More info here: http://www.sonnettech.com/product/echoexpresscard34thunderbolt.html

  The price seems resonable too at $170.

  I understand that it does not replicate the PCI Express 2.0 x 1 to 2.5Gbs in contrast to USB adapters discussed in this thread (which of course will not work):

  http://forums.NI.com/T5/PXI/MXI-over-USB-3-0/TD-p/3105557

  I don't have a laptop with crush to try myself as its still quite old (4 years) to have ExpressCard.  But I am concered that when I update I will have very limited choices in laptops ExpressCard. It suits me to do development on my laptop and then to the PC to get it into production.

  Concerning

  Nick

  Nick,

  I tried this at some point.  It works at least nominally.  I don't know the nuances with connection hot and things of that sort, but it is quite functional.

  -Robert

• Problem of lack of resources for IEEE 1394

  We currently have a CVS-1454 with two cameras inspections.  Due to circumstances with the inspection and machine, we try to move the inspections to the computer that communicates with the RESUME.  We get the error "the IEEE 1394 camera could not be initialized because of the lack of resources on the IEEE-1394 bus".  This error occurs only in Vision Builder.  This is not the case in MAX.

  The specific features of the system are: the PC is under XP SP3 with a card PCI-8252.  There are two cameras from Basler scA1390-17fm of the inspection.  The cameras are using the 7 Format, Mode 0, 1392 x 1040.  The PCI card is new out of the box, the cameras are a couple of years.  VBAI version 3.5, LabView 8.6, MAX is version 4.6.2.

  I found the articles on NI.com addressing this issue, but the recommendations have had no effect.

  1. Package size & framerate: in MAX speed can be set on a 100Mbs.  Reduce the size of the package has no effect.  It has been set to the default value to 1024, but we lowered it to 200 without effect.
  2. We installed the driver of Bus AVT Package, but when we went to the driver of the TRA, the bus went to the MAX and then Windows through the new hardware wizard found and we couldn't get the cameras is displayed correctly in the Windows Device Manager, nor did they ever appear in MAX.  All of the documentation I've seen looks that we should not need to install additional drivers for the Basler cameras.
  3. The machine does not have hotfix 885222 installed, but I contemplated trying to run this update anyway: http://support.microsoft.com/kb/955408
  4. Alternate video modes: we have tried to put the cameras to any other video mode.  We can put a camera in an incredibly small resolution, but then the camera still does not work regardless of the video mode.

  I hope that I put all the details there.  Any thoughts?  Should we need to install anything else after the passage in the AVT bus driver?  I was full of hope that would solve the problem.

  Thank you

  Paul

  I agree with Brad, your question is probably the famous issue of Microsoft that XP SP2 and SP3 downgraded a potential to S100 speed, requiring to be restore the driver 1394 SP1 of Microsoft, or switch to Win7 where they finally solved the problem.

  Or by using a substitute 1394 Microsoft compatible spare driver, such as the one offered by AVT.

  But I differ respectfully with Brad that re. If the driver AVT 'worked right' or not... as it was only designed to work with AVT cameras - and will not work with Basler cameras.  This is a deliberate design feature.  Or constraint,'s point of view.  ;-)

  Scott

• Interface not found error when using Snap example for Firewire (IEEE 1394)

  Recently, I installed a SONY XCD-SX910 in interface with Labview 8.2.  When you choose the driver, only the Legacy driver would work for the installation of Firewire (R) (or IEEE 1394).  After installing the driver, I have images of the inteface to MAX.  However, when you attempt to trace through the example of Snap 1394 legacy since the document installation IEEE 1394, I get the error "Interface not found".  I tried a few iterations to try to name the camera as "cam0' (the name given to the camera to the MAX) and" cam0: SONY XCD-SX910.  However, the error continues.

  What should I name my camera so he could find the interface?  Will there be another underlying problem that is not obvious?

  Control of IO is not something that will be filled when you use the Legacy 1394 driver. If you use IMAQdx as your driver, it will fill. Thus, when you use the Legacy 1394 driver, you have control of the chain on your façade. When you use control of the chain, you must set the name of the camera as "cam0" as you did before. As long as this corresponds to what is able & Automation Explorer, you should be good as long as MAX uses the same driver that you are trying to use.

• Remove client services for Netware to connect 1394

  How can I remove the Client for Netware a 1394 connection?

  Hello

  Your question of Windows is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the public on the TechNet site. Please post your question in the below link:

  http://social.technet.Microsoft.com/forums/en-us/winserverNIS/threads

• IEEE 1394 Port SL500 - does not work for me

  Hello. This is my first time.

  I tried to connect my SL500 to a recorder Digital hard disk using entrance to DVI of the recorder and the port IEEE 1394 of the laptop on the left side near the front. The goal is to save a slide show of pictures, or other photo folders, with music from Windows Media Player, on a recorder to external hard drive (made by LiteOn) where I can make a copy on a DVD-R. However, there is no signal coming out of the port IEEE 1394 laptop. When I plugged everything together there was a message saying that the 1394 connection has been recognized and ready to use. But still no signal. With no other connected external monitor, I tried Fn + F7 to display on an external monitor, but which was not allowed.

  I used the same IEEE 1394 cable in the past to copy the DVI output on my digital video camcorder on the recorder's DVI input Digital hard disk to make the DVD. So, I know that's not the problem.

  The website of Lenovo and Lenovo Care online help doesn't give any idea on how to make the IEEE 1394 port. Someone out there has a suggestion? My warranty expired about 1 month ago and support won't talk with me about this, unless I have buy a new guarantee $ 500 (approximately).

  I really like the SL500. It does everything I need and does it well, except for this problem.

  First check to see if your external recorder is displayed in Device Manager. If this isn't the case, drivers must be found either MSoft LiteON.

  For the port IEEE1394 SL500 transfer the data on your device external HARD drive you will need to walk manually assign a drive letter, if its not automatically on connection. That could be your second problem.

  Hope this helps

• interface for Windows 7 1394

  I have an old model number The of digital camera Panasonic's PV-DV900. I have a DV - USB interface IEEE 1394 PC connection cable... I have Windows 7 Home Premium on an HP PAVILION laptop. I looked for a driver to connect these two systems. No luck. What are my options... Brad Gale * address email is removed from the privacy *

  Hello

  I suggest you to see link and check.

  A compatible IEEE 1394 device does not communicate with a Windows Server 2008 R2 or Windows 7-based computer that is not the Manager of IEEE 1394 bus

  http://support.Microsoft.com/kb/2599521

  Tips for solving common driver problems

  http://Windows.Microsoft.com/en-us/Windows7/tips-for-fixing-common-driver-problems

  I also suggest you to contact Panasonic support and check.

  http://shop.Panasonic.com/support/