Similar Questions

• My ID apple has been disabled and I can't restore it because I forgot my security question, please help

  My ID apple has been disabled and I can't restore it because I forgot my security question, please help

  I can't update my iphone because it will need for my apple for activation ID. Please help me.

  Contact Apple for assistance with the security of the Apple ID - Apple Support accounts

• DELL INSPIRON N4010 WEBCAM QUESTIONS: PLEASE HELP... DELL CUSTOMER... AND ANYONE WHO HAS KNOWLEDGE REGARDING MY PROBLEMS...

  I have a Dell Inspiron N4010. Configuration: 1st generation i5 processor with windows 7 home basic 64-bit.

  3 months after the purchase of my laptop, I have updated my Dell webcam central through the applications update service... Shortly after the update, my integrated webcam has started to show problems.

  DESCRIPTION OF THE PROBLEM:

  Shortly after the update of my installed factory Dell webcam central, my integrated webcam has begun to show the problem. webcam was able to start with any application such as Skype or dell central webcam himself. Instead, webcam LED flashes for flicker of a second, and then goes away without any streaming video.  Trying to open it, an error message is displayed: "your webcam can be used by another application. Close the application to launch streaming video".» Initially, the problem was temporary, that is occasionally the webcam began video streaming without any problem, but as the time passed, webcam stopped working almost completely.

  TRIED SOLUTIONS:

  I tried all the solutions mentioned below:

  • I uninstalled the Dell webcam software and reinstalled with the version installed in the factory, supplied on CD with laptop. Uninstalled the webcam via the Device Manager and reinstalled, but without success.
  • I heard that there is a conflict between the Dell face recognition software and dell webcam central. So, I uninstalled the dell face recognition software. After that, the webcam worked for a few days, and there still rebooted problem.
  • I went through various forums online, dell community, customer service, etc. and everything suggested tried but without success. I heard several times that this is not a hardware fault but driver error. Even in a few forums, its says that Creative Technology Limited have not been able to supply webcam drivers compatible with windows 7 64-bit.
  • I even did factory restore my laptop twice, but could not do my webcam works.
  • Then, I decided to format my system and installed windows7 again with the disc that came with my laptop. During this process, I have kept the recovery drive and the untouched OEM disk untouched. I have reinstalled all the drivers in such order as advised by Dell. Despite puts everything in order, I couldn't do my built-in webcam work. More... now I can't even access the Dell factory restore option despite the fact that my recovery disk is intact and it is to have all the files into it!
  • I tried the utility dell online Diagnostics. He could not detect any error webcam!
  • Few days back, I used the dell startup screen diagnostic utility and scanned the built-in webcam to find errors, and my webcam failed in all tests! Here are the screenshots of the tests:

  

  

  

  

  

  

  

  

  

  

  

  

  

  

  I GUESS I GAVE ENOUGH INFORMATION THAT CAN HELP TO DIAGNOSE THE PROBLEM WITH MY DELL INTEGRATED WEBCAM... I ASKED DELL CUSTOMER SERVICE TO HELP ME SOLVE MY PROBLEM OF WEBCAM... AND ALSO THE FACTORY RESTORE INACCESSIBILITY PROBLEM... PLEASE HELP ME...

  AFTER AN ENTIRE WEEK OF UNINSTALLING - REINSTALLING VARIOUS DRIVERS & SOFTWARE FOUND IN THESE FORUMS, SUGGESTIONS INCLUDING REINSTALLING WINDOWS FROM DELL DATA SECURE BACKUP.  THIS IS WHAT I LEARNED.

  My problem was. No supported webcam not connected when I ran dell webcam central. No program could access the webcam. Device Manager showed SPECIFIC DEVICE. Camera suddenly stopped working! I had a little more hair when this problem started.

  I have Inspiron N4010 windows 7 Home premium. Are the drivers for the webcam in windows 7, there is no separate drivers available anywhere. with the exception of some XPS models.

  A post in these forums suggests to abolish the plastic around the display bezel. It's simple. Just carefully go around and remove. It is clipped without screws on my system. This gives access to the webcam hardware. I got dell webcam central on-board. (showing no supported webcam connected!). Gently, I tried to disconnect the connector of the webcam. My intention was to disconnect and reconnect. I barely touched and the fire came and windows immediately started to install device drivers. A beep and an icon in the notification bar popped up. A few minutes, I saw my beautiful mug on the screen to my absolute delight.

  Guys, if you have a problem where Device Manager does not recognize your webcam for most probably, this is a hardware problem. The small rectangular plate on which is mounted the webcam is not properly secured by DEll. It is a DESIGN PROBLEM. The Board is located in place on two small round plastic holders without any screws. It can move easily. The bezel plastic when it is installed itself that holds it in place, but not very effective. When you open and close the lid of the screen, especially if you are taking in the middle where the camera you finally loose connector. That's why some messages will tell you what they camera has stopped working suddenly and then started working by himself all of a sudden. When I put the bezel plastic, it snaps into place, I was able to move the camera, and it stopped working again. A little gentle jiggle got running again and its been since.

  It does not matter what version of central webcam you have in windows 7. It runs on windows Vista service pack 2 compatibility mode. (Find WEBCAMDELL2. EXE file under programs x 86-dellwebcam-dellwebcam Central-dell webcam central. Right-click on the file name. Select Properties. Select the Compatibility tab and run this program in compatibility select windows vista service pack 2).

  If in your case even though there might be a software problem. always try this simple 2 minute solution b4 safe spending frustrating days find the drivers and software. Hope this post helps someone. May work on other systems too! Good luck! and thank you to the guy who led me down this path and misery!

• Touch pad questions, please help.

  Laptop HP Pavilion

  Model: 15-n096sa

  Product: F4T58EA #ABU

  OS: Windows 8.1 Home Premium X 64

  I installed Windows 8.1 Home Premium X 64 on my laptop last week, he had originally version 8 is installed when I bought a month ago. Since the upgrade of the OS of my touchpad is no longer allows me to scroll with two fingers or enlarge the pages, use the right click function by tapping with two fingers & also bring up the options in a Sling. All I can do now is to move the pointer and click or double-click with the pad.

  Can someone please help me solve this problem because it drives me crazy?

  Thanks in advance.

  Hello EnergySyndicate,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I understand that you are having problems with certain features of the touch pad doesn't work does not correctly. I think it's a question of settings. I'm you provide a HP support document: use and troubleshooting of the TouchPad and ClickPad (Windows 8) that will guide you in how to adjust settings and ensure that the common gestures of the Touchpad is correctly configured.

  I think that this will solve your problem of Touchpad and allow you to go back to listening to your computer. Thanks for posting on the HP Forums. Have a great day!

• I'm fixing to the top of my old computers for poor children please help!

  I convinced my boss to difficult six old computers, we all either throw away or sell in bulk... I already fixed one of them and it loaded with interactive games for children, here at the Mexico there are many child care for poor children whose children have no idea of what a computer looks like. Please help me to set up!

  I turned on the PC "#2" today but first, he would not go to Windows, the black screen said it was a mistake Floppy... I went to Advanced BIOS Features and make the following settings: first Boot - FLOPPY, Second Boot Device device - CD-ROM, third boot device - disk HARD-0... after that, it took finally me in the Windows log in page, but after I click on the user name to log on, the computer stops :( Help!

  Hello

  You do a great job in helping children to learn the technology.

  · What do you get the exact error message was on black screen?

  · You have windows XP place the disc?

  · What is the number and the model of the computer?

  Change the boot sequence and set the hard drive as the fist boot device and also Devil the floppy drive and try to start the computer.

  Note: changes to the BIOS/complementary metal oxide semiconductor (CMOS) settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

• My laptop cannot read a CD/DVD. It is a challenge for everyone. Please help help help. ? __

  Hi friends!

  (It is not really a problem, it's a challenge).

  (Before responding, pls read the question carefully)
  First of all, my laptop description:
  Model: Lenovo Y410 7757 54Q
  Operating system: Windows Vista Home Basic

  I use this laptop for 2 years, but there is a problem with this, it is not able to read any CD or DVD, except a few bootable and driver CD/DVD provided by Lenovo and Microsoft at the time of the purchase of this laptop. I encountered this problem several times and I have concluded that this problem can be related to the following questions, as:
  1. Windows registry database
  2 CD/DVD-ROM driver (it is MATSHITA DVD - RAM UJ-85JS ATA Device)
  3. the system BIOS or CD/DVD-ROM Firmware
  4 Codecs
  5. hardware system (i.e. lens or CD/DVD drive itself) and
  6 operating system

  But, I think that this problem is not related to Codecs, operating system or hardware. In any case, it is more than enough for me. I can not be tolerated this problem more. Please, help me out of this problem, so my system can play all types of CD/DVD and I can work properly. This issue is open for anyone who thinks they are an expert in computer science.

  (Ask: answer this question if you could understand what underlying problem and please please don't make stupid as responses to install codecs or clean your lens etc..) Now I really want to get rid of this terrible problem.)

  1. create an of Linux Live USB key and start it. You must run Linux from a USB key because you want to keep the free CD player. This site will show you how.

  http://www.pendrivelinux.com/

  2. Once booted into Linux, test the drive trying to play multiple CDs / DVDs. try to burn something using any burning program is available in the Linux distribution you use. Knoppix, it's k3b.

  If the disk fails under Linux at any point, replace the disc. MS - MVP - Elephant Boy computers - don't panic!

• go mini questions please help!

  When I turn on my HP mini computer her talk me to "enter the current password" and after three trys it says "system error fatal vaulted password control failure" with code "CNU9475MH7" Please help me through this form as soon as POSSIBLE. I need the important information on this computer!

  Try to ally.

  e9lovxq4zx

  3rd letter tiny L.

  4th letter lowercase O.

  7th letter lowercase Q.

  Use this code to go into the BIOS.

  Disable all passwords that are enabled.

  IF demand for CURRENT password using this code.

  REQUEST NEW password just press ENTER.

  If asked to hit just to CHECK password to enter.

  Save and exit.

  REO

  I must inform you that these services are not endorsed by HP, and that HP is not responsible for any damages that may occur to your system using these services. Please be aware that you do so at your own risk.

• Wireless driver do not install for HP - D107TX, please help?

  Hello

  Recently I bought HP D107TX laptop and I tried to install the form of driver WLAN on your site. But it is not installed. When I click on the setup.exe it unpacks the pilots and shows a message "this program installed correctly" and "to Reinstall recommended setting using". So far, Wireless does not work on my knees. Please help me solve this problem.

  Thank you

  Concerning

  Andrée

  You are the very welcome.

  Here is the link for the driver for the usb controller 3, you must...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-127803-1&cc=us&DLC=en&LC=en&OS=4063&product=6521374&sw_lang=

• WRT150N questions, Please help!

  So I just moved into my new House and set up my internet. I used my router before without any problem so far. So my problem is that I have this linksys router and a motorola 2210 dsl modem AT & T Eh well, if I run the Ethernet directly from the modem to the computer internet works fine. But once I added the router I can not get a connection. With the connected router, I have all green in all areas on the modem and the router "I should be connected by saying" my wireless devices are showing my hense network I should be able to connect to it. But it always says connection failed... At one point, I even had my office that I was connected to 54 Mbps but still my home page would not load. I have no idea whats wrong. The internet is coming through, my wirelss peripheral are picking up that I have a network but I can not connect unless I'm jacked right at the source. Please help me understand this. (and Yes, everything is pluged in the right way)

  AT & T usually configures their Motorola 2210 to the PPPoE connection for you and use the 192.168.1.x subnet.   With its default settings, your WRT150N also tries to use the 192.168.1.x subnet.  But you can't put the same subnet on the Internet (WAN) and the ports LAN of the WRT150N.  It will be, or does not work at all it will not work properly.

  To fix the problem do the following:

  (1) put your entire network.

  (2) disconnect all other devices WRT150N.

  (3) use of an ethernet cable, the son a computer to one of the four ports LAN on the WRT150N.

  (4) turn on the WRT150N and your computer.

  (5) connect to WRT150N to 192.168.1.1

  (6) in the WRT150N, replace the "local IP address" 192.168.2.1

  7) click the 'Save Settings' button and then wait for the screen refresh (3 to 60 seconds).  You will be probably disconnected from the WRT150N.  Don't worry about this.

  Exit 8) your browser and put your entire network

  (9) with an ethernet cable, connect the ethernet port on the Motorola 2210 to the Internet of the WRT150N port.  Leave your computer connected to a LAN of the WRT150N port.

  (10) power of your network.  It should work.

• GANYMEDE + question: Please help

  Dear all,

  It is with regard to Ganymede +. I have configured Ganymede + on switch cisco, but it is local user name and password

  for authentication.

  With below configuration on the other switch, works very well with Ganymede + username and password, but not with

  This switch.

  AAA new-model

  AAA authentication login default group Ganymede + local

  AAA authentication login no_login local

  AAA accounting send stop-record an authentication failure

  AAA accounting exec default start-stop Ganymede group.

  orders accounting AAA 15 by default start-stop Ganymede group.

  Default connection accounting AAA power Ganymede group.

  AAA - the id of the joint session

  RADIUS-server host 10.0.2.193 touches 110A101614425A5E57 7

  RADIUS-server application made

  username admin privilege 15 password *.

  line vty 0 4

  transport input telnet ssh

  by default the authentication of connection

  Also, this switch is configured for intervlan routing, with the following configuration and I added 10.0.6.1 address IP Cisco ACS.

  interface Vlan5

  the IP 10.0.0.1 255.255.255.0

  !

  interface Vlan20

  IP 10.0.2.1 255.255.255.0

  IP helper 10.0.0.7

  !

  interface Vlan60

  IP 10.0.6.1 255.255.255.0

  REFLXIS_PUNCORE #show Ganymede

  GANYMEDE + server: 10.0.2.193/49

  Opening of socket: 33

  Firm grip: 33

  Write-offs of socket: 0

  Socket errors: 0

  Socket timeouts: 0

  Failed connection attempts: 0

  Total packets sent: 33

  Recv packets total: 0

  So please help on the same.

  Hello Eve,.

  the IP address of the server 10.0.2.193 is accessible in 20 Vlan.

  Therefore, the switch will try to connect to the server using the address IP of Vlan20, 10.0.2.1.

  You can fix this in two ways:

  1. change the configuration on the radius server to have an entry with 10.0.2.1 instead of 10.0.6.1.

  or

  2. change the configuration of the switch, adding "ip radius-server source interface vlan 60.

  Please indicate the so useful post

  Marco

• I just bought the app photoshop for a student, but when I go to open it in my application it says that I have to buy when you already took my payment for it. Please help me!

  I just bought the app photoshop for a student, but when I go to open it in my application it says that I have to buy, when adobe already had my payment for it. Pleas help me!

  Hi Charlotte,.

  Please check the help below document:

  Creative Cloud applications unexpectedly back in the test mode. CS6, CCM

  Kind regards

  Sheena

• Layer Mask question, please help.

  Hello

  My layer mask does not work, do not know what is happening. I use 4 CS. I want to use the blend effect so I put the photos on a white background. I click on the layer mask on each photo, select the tool brush on the picture but does not work, is either appear black or white when I use the brush paint on it. So not bad, the foreground color should be gray & white based on layer mask, but it appears black & white instead. Please see the screenshot below. Please help, thanks

  

  Hi, I'm going to try explain your problem.

  In your posted example we see that you have three layers in the layers panel.

  On each layer, we can see, on the left side, there is the thumbnail of the layer, it is a display of the actual image of your layer, then a thumbnail of the layer mask (the white rectangle on the right side).

  A layer mask works as follows: you tell Photoshop to show or hide the actual parts (pixels) of the layer with the grayscale values. Indicates a white pixel on the layer masks Photoshop to display the area of the image with a (non-transparent) full opacity, while tells a black pixel on the Photoshop layer mask to hide the layer completely (0% opacity.) Gray values will therefore partially show the image data.

  But you paint on the document, and you must specify Photoshop if you want to paint on the image (what you did in your example, and you don't want to) or if you want to paint on the layer mask (what you want to do). This indication is called targeting. It is simply done by clicking on the thumbnail of the layer or the layer of your layer mask thumbnail. (By clicking on different areas of a layer in the palette layers are different orders, you give to the program). For example, if you want to move the layer that you hide to another, in order to paint on his mask, sure to click on the layer of the other layer mask thumbnail in the layers panel.

  In Photoshop CS5.5 and earlier versions, you'll see that a layer or its mask is targeted because there will be three contours around her: a black, a white and a black once again, as the actual layer data in the highlight 0928 your image layer. You should see these three contours around the layer mask to paint over it.

  CS6 the target indicator is different, look in my image, we can see that the layer mask is targeted with white corners: I then have the part of the black layer mask by targeting the layer mask in the layer panel and then paint on the image where I want to hide the layer.

  

  If you want to change the layer (photos, in your case), just click on the thumbnail, and you're ready to go!

  I hope this helps.

  See these help documents: laquerbe Basics: http://help.adobe.com/en_US/photoshop/cs/using/WSfd1234e1c4b69f30ea53e41001031ab64-78e3a.h tml

  Layer masks: http://helpx.adobe.com/photoshop/using/masking-layers.html

  Some the search results for "Masks fundamental layer" in Photoshop help: http://community.adobe.com/help/search.html?q=layer+mask+basics&x=0&y=0&lbl=photoshop_prod uct_adobelr & hl = en_US & lr = en_US & auto = 0 & area = 0

  (It is one of the best ways to search for files of tutorials or help)

  Stone

• Sync for Apple missing, please help!

  I got this message after I've upgraded to IE9 on Vista, please help: SQLite3.dll  Applesyncnotifier.exe

  Hi lilmoose25rollwave,

  ·         Exactly when you get this message?

  ·         What is the exact error message?

  Perform a clean boot to see if there is a conflict of software like the clean boot helps eliminate software conflicts.

  Note: After the boot minimum troubleshooting steps, follow the link step 7 to return the computer to a Normal startupmode.

• I can't open choose front page, when I tried to open choose front page, he was just waiting for the download, please help me

  I can not connect to choose the plan window, sir. Please help me

  Sincere,.

  Hello

  If please try it on another browser, or click on the link below CC price and membership plans | Adobe Creative Cloud

  If you're still having problems, you can contact our sales support here http://www.adobe.com/products/request-consultation/marketing-cloud.html

  Let us know if this helps!

• fusion of forms in question please help

  
  I have a problem: when I tried to merge forms into one with pathfinder, I lost part of the mountain... Please help me. How can I merge without losing?

  Make transparent traces on the forms of mountain before using 'unit '.