Failure of the HD on Pavilion a1610n

Similar Questions

• Pavilion dv6t 7000: failure of the BIOS (Caps lock flashes twice a secone)

  My laptop model number is Pavilion dv6t 7000. In recent days, he had a problem. When I turned off my laptop and put it off, the next day I find that is not starting. A black screen, caps lock shift is blicking twice and f12 key is red (WIFI). Nothigs happen. Then, I searched and came to know that it is the failure of the bios. Then I tried some way and nothings worked. ATLAST when I remove the cmos battery it set again after 2 or 1 minute its starts fine. Then againg I turn off the computer and its power day following again the same problem. I was to solve this problem by removing cmos battery and put it again for 4 or 5 days. But today this tip does not work. I tried so many method like (Windows key + B), (byholding down the power button for 1 minute), (Flash UEFI) etc. to solve the problem of failure of the bios, nothing worked at all. What is the problem?  Is this really a failure of the bios? How can solve this problem? What is a dangerous problem? There the chances that my laptop is completely exhausted?

  Hello
  beep codes or led lights will Flash at the start of the system may indicate a hardware fault or BIOS you say you have tried all the troubleshooting steps
  
  I would like to run the hardware check to make sure it's all working please follow the guide below for instructions and report:
  
  http://support.HP.com/us-en/document/c03467259#AbT1
  
  Tests using UEFI diagnostics and run the quick test
  
  Thank you
  James

• I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I tried the holding of 'command-r' and 'option' to see if the problem can be resolved or try any boot from a boot disk, my old backup, USB function start - but after a slow long process it all just stops.

  There is software on my HD that I don't want to lose by simply reformatting the computer, because I am now in a different country, far from my house, which is another problem of the Apple Store, to reinstall my OS from Yosemite on the www.

  Hey AmnonMikeCohen,

  Thank you for being a part of the communities of Apple Support.

  I understand that your Mac is not start properly after the power went out.  Let's start with resetting the SMC and NVRAM on your Mac and see if he can start from there:

  Reset the management system (SCM) controller on your Mac.

  How to reset the NVRAM on your Mac.

  See you soon.

• Interesting solution of failure of the fans occasionally cold start?

  Interesting solution of failure of the fans occasionally cold start?

  Normally I do a reset of the SMC, sometimes it's the solution.

  When kick cooling fans as soon as I start my cold iMac, I just quickly swivel the iMac slowly from right to left and the cooling fans have stopped.

  Strange?

  All the answers?

  Note: I use an iMac 21 inch end 2013-2, 7 GHz Intel Core i5

  Thank you in advance for the answers.

  This sounds like a sensor loose or pinched wire.

  You may be able to see the problem of sensor or sensor wire with the diagnosis of Apple to test or a third party temp. followed by the application, but the best would be to book a service appointment at your local CENTRE.

  Apple Diagnostics using - Apple Support

  https://locate.Apple.com/

• failure of the SIM, why I this message all the time?

  failure of the SIM, why I this message all the time?

  This means that your SIM card is defective or otherwise expired

  Can you make and receive calls and texts?

  If so - go out the SIM card - wait about 45 seconds and re insert it back

  If not - contact your carrier for a new SIM card

  Remove or change the SIM card in your iPhone or iPad - Apple Support

• Qosmio X 70-B-10 t - failure of the graphics card

  Hello. I offen had failure that the graphics card driver hang up and recovered himself. But today, I got this failure to the course to watch live TV streams and it seemed to me that the laptop does not work correctly. I tried to restard and then I get this message: DRIVER_IRQL_NOT_LESS_OR_EQUAL (cmdhlp.sys). It must be the graphics card and I don't think it's a hd or RAM failure in this case.

  Any tips? Repair? New graphics card?

  Thank you!

  On this virtual path, it is not easy to say what can be the reason of this failure.
  Repair is always the last step. What you can do is to test the features using Notepad with "factory settings, without having to install additional software.

  What operating system do you use?
  Do you use the original display driver or some day?

• Failure of the audit on the iPhone, but works in iTunes

  Hello

  I had a strange problem:

  I can log on successfully to my desktop (Windows) by using my AppleID, can see my account balance and buy free apps.

  But I use the same AppleID on my iPhone 6Plus, it always shows: "failure of the audit, your Apple ID or password is incorrect."

  can anyone help?

  Thank you very much.

  Hi all

  After 2 hours of research and new attempts, I finally solved this problem.

  1. just to keep a new attempt on the iPhone, until the account is locked.

  (Note, only the account on the iPhone is locked, can I still use iTunes Windows and web to connect on the same Apple ID]

  2. then follow the instructions on the screen to unlock the account.

  (you will be asked 2 secret questions when the account is set up a few years ago)...

  Once the reset is OK, the same account is included to connect the iPhone and buy apps.  (Yes..!)

  Hope this will be useful.

  kpang1

• Failure of the Time machine backup could not save "My Passport"

  When I try to do a backup on my Passport using Time Machine, he used to work over the years, and now it is the message I get:

  Failure of the Time machine backup could not save "My Passport"

  
  

  Does anyone has an idea to help me with this problem?

  
  

  (Sorry for my English but I speak French in Switzerland...)
  

  Have you tried to run utilities disk to check/repair the external hard drive? Here is something you can try.  http://pondini.org/TM/A4.html

• HP PAVILION NOTEBOOK PC G7: How can I download the driver hp Pavilion notebook form g7 graphics radeon on processor intel

  someone can tell me, how can I download the driver hp Pavilion notebook form g7 graphics radeon on processor intel

  Hello

  What is your Pavilion G7? Please follow the instructions below to find the product/model of your machine:

  http://support.HP.com/us-en/document/c00033108

  Kind regards.

• Failure using the charger VxD (Code 19).

  Norton 360 detects the unusable device;

  Failure using the VxD (Code 19) charger

  F:\ G:\, H:\ and I:\

  Type Devives Protable

  Generic Manf

  Location: On UMBus Emunerator

  Device status Windows cannot start the device hardware information (in the registry)

  is incomplete or damaged (Code 19)

  What is - this and how I can fix it.

  My computer is a series of beeps 3 x 3 about 30-40 seconds after the connection.

  Thanks for any advice.    John

  Hi jcjohn

  Does not offer much help, but I picked this up in the Norton Community Forum

  http://community.Norton.com/forums/Code-19-failure-loading-using-VxD-loader

  With a possible solution from Microsoft:

  http://support.Microsoft.com/kb/314060

  If the problem is not resolved, try the Norton Forum:

  http://community.Norton.com/forums

• W510: How do I access my data from a failed hard drive after the failure of the motherboard

  I made a mistake and has paid for major .

  This error pouring a drink sweet on my laptop. I know, I know, my keyboard can and protect against damage caused by the spill, but it was a drink together. In any case, I panicked and shut down the system and it has upset and removed the keyboard. And be the impatient person that I am, I made what was probably the ultimate error. I do not give everything save a sufficient amount of time to dry and I tried to boot the system. There is my computer. Or at least I think.

  Symptoms: It began at the start, kept a beep, sometime just close and will start.

  In any case, I guess that my laptop went kaput. Now to the point of this thread. I had not been a recent backup and can't remember when the last backup was actually made. Assuming that my hard drive is ok, I want to get all my data, so I saw several options:

  -Send the system to a data recovery service where I will not pay less than $300, but probably 2 to 3 times what

  -buy an equivalent model laptop and put the HARD drive in there

  -by an external SATA hard drive enclosure and mount it via USB on another computer

  I bought a box external and assembled this evening. I had read about the data access of difficulty with a system non-Lenovo because of encryption of the data. I proved that by linking it to my work (a Dell) laptop and I couldn't access my data directories. If I have access to an another Lenovo Thinkpad, I'll be able to access the data if connected via USB? I had read that I can access the contents of disc hard if it is connected to an another Thinkpad, but I knew not that if it means that I have it connected via SATA connection or if there is work through the USB port.

  I'll appreciate any suggestions for accessing my data.

  Best regards!

  All,

  Thanks for the suggestions.

  I was able to recover my computer and all data on it.

  Just to describe what I have done, here are the details.

  Because of my concern about a failure of the motherboard, I bought a used/given new keyboard and an external SATA drive enclosure. I was not able to properly take possession of the car from my other laptop, but I was able to access the data in Mode without failure. With my data, I plugged the hard drive and the new keyboard in and started without problem.

  Thanks again,

  brent86

• Domain Services Active Directory could not create the ntds object due to dns settings look for failure on the specific domain controller

  Forest consist of 1 DC server 2003 with all fsmo and 2000 1 domain controller roles.

  Completed all questions of adprep and when I tried to promote server 2008 standard edition to a domain controller, had the error message stating that Active Directory could not create the NTDS settings for the domain active directory CN = NTDS controller

  Settings, cn is 2k8dc1, cn = servers, cn = Default First Site Name, c is Sites, cn = Configuration, dc is Marie-France, dc = com on the ad distance dc server2.amanua.com.

  To ensure that the provided network credentials have sufficient permissions

  "The DSA operation unable to act because of the failure of the dns lookup"

  The idea was to demote the 2000 machine when I completed the installation of 2008.

  Hello

  You can display the query in the link provided to improve assistance:
  http://social.technet.Microsoft.com/forums/en/categories/

• Could not start the automatic updates. Get an error that Windows cannot check the updates, D0000034 after the failure of the Java updates

  OP: Action Center... PC problem: 1 important message

  After the failure of the attempt to install the JAVA update, I received this message from Action Center... Windows cannot check the updates. So I was taken to the dialog box and retried to check the updates of windows fails again with the code D0000034. Also did a system restore to the place before the installation of JAVA update attempt, but was no help. Can you help me?

  Hello Irfan,

  Thanks again for your response. Since your last I discovered through my system status (Control Panel), I wrote that my product ID and the Windows 7 activation status not available. So I followed instuctions to help and microsoft support to activate.  Yet once, I got the error code D0000034 as before with the problem of update. However, I was given the opportunity to phone, but received no phone #. I bought the DVD of Windows 7 and installed on the PC that was custom built for me.  On the site Web microsoft help and support, I was asked for the product ID, which according to them is a # 20 numbers.  Not the only one, I have is the product key which is one 25-alpha-numeric.  I tried to enter only and does not pass.  This is why I say that I can pay for help since I did not ' have the product ID.  Maybe it isn't your area of expertise, Irfan, but I was hoping... I re - install windows on last April when I got in trouble and probably did not re - activate? What do you think?  If you can get back on track, I would be very grateful and thank you once again to be a big help!

  wandrinstar

  Please ignore above request. I have since re-activated Windows and the problem was solved with technical assistance telephone and thank you again for your help, Irfan. Also thanks to all the people answering the phone at microsoft. The experience I had was really a pleasure. I wasn't expecting such an attitude courteous and professional.

  Keep up the good work,

  wandrinstar

• Is windows update causes the failure of the system?

  I have windows XPsp2 and I've updated with XPsp3 and it takes place in a few errors and the failure of the system to my PC. Unlike my aunts PC she XPsp1 with a slow internet connection so she was not able to update, but it works for more than a year. then the causes updated a few problems in the future?

  No, do not keep your computer fully patched all the time causes more problems.

  4 steps to protect your computer
  http://www.Microsoft.com/security/pypc.aspx

  NB: If WinXP SP3 is not installed by April 12, 2010, your computer WinXP SP2 will not be offered as all other reviews of security updates and the Windows Update Web site will not be available.er

  The above has applied to WinXP SP1 computer your aunt since October 2006.

  For you and your aunt...

  HOW to get a computer WinXP SP1 or SP2 fully patched
  http://groups.Google.com/group/Microsoft.public.WindowsXP.General/MSG/a066ae41add7dd2b

  ~ Robear Dyer (PA bear); MS MVP (that is to say, mail, security, Windows & Update Services) since 2002. DISCLAIMER: I do not represent nor don't work for Microsoft

• HP6830: Failure of the print queue

  HP replaced my 6830 due to failure of the print head. New printer works proud desktop using Vista. Previuosly I could print from my laptop wireless as well, but it's time the print queue says printing, fails to print and return to errot impression. I know that thw laptop is connected to the printer thr and I even can it ping ipconfig without problem. I have been through software support, and to the low load options hear everything without any result. I am now confused.

  Hi @3391816Sablenip,.

  I read your post and see that the replacement printer is wireless print on the Windows Vista-based computer, but not the laptop running Windows 7. I will definitely do my best to help you.

  If you have a valid IP address for the printer, then try and access the Web built-in to the printer server.
  Type the IPv4 address in the address bar of your web browser. (Internet Explorer) It to load the page.

  You mentioned that you can test the printer, just to check a real contact, check the network IPv4 address on the computer to see if the first 3 sets of numbers match the IPv4 of the printer address.

  Press the Windows and R key at the same time, to show the command line run, type cmd, then type Ipconfig.
  Check the IPv4 address.
  Now, check the IPv4 address for the printer.
  If this isn't the case, then the printer and the computer are not on the same network.

  Do the first 3 sets of numbers match?

  Check the address IPv4 of the computer to verify that it matches the IPv4 of the printer address.
  Printers and devices, right click on the printer, on the left, click printer properties, select the Ports tab, click on Configure Port.
  If they do not match and then close the window configure the Port and click on create a port and follow the instructions in the wizard.

  Type the IPv4 address.
  Make sure the printer is online.

  Test the printer. If creating the new port doesn't work, run the Add Printer Wizard.

  If you're still having problems, download and run the print and Scan Doctor, he will diagnose the problem and could solve it automatically.

  What were the results when you ran the Print and Scan Doctor? (she print or scan, error messages)

  If the problem persists, try the following steps to see if it will be useful. HP printers - print jobs stuck in the print queue (Windows).

  If you appreciate my efforts, please click on the "Thumbs up" button below.

  If you have any questions, please let me know what steps you have taken and the results. Thank you.