File copy error

Similar Questions

• large file copy error: specified network is no longer available

  Hi, I can not copy the files from large as data 1 GB, 2 GB or so on my network xp but I can copy files of 100 MB to 50 MB with no problems, I got an error, can not copy the file, or the specified network folder is no longer available or some trail time is too deep (in the case that a single file is available on the root)

  Hello

  • What were the changes made before the show?

  You can view the steps that are provided in this link:

  Advanced Troubleshooting for Windows workstations network card

  http://support.Microsoft.com/kb/325487

  Also see this article to update the network adapter drivers:

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

• DOCUMANAGE error #2002 (file copy error)

  Hello
  I get this error "Error #2002 Documanage (copy file error)" during the process of Genarc. I am not able to understand the problem. Can you get it someone please let me know about this error.
  
  Also is there documentation on documanage errors, please let me know.
  
  Thank you in Advace

  Put your debugging options in INI Documaker and see what you get.

  < dbhandler:dmia="">
  DEBUG = YES
  < dbhandler:odbc="">
  Debug = YES

  You can also introduce you to your record in the poffice.ini and check the logs as well. It's been a while since I've seen it, but if I remember correctly it occurs usually when you try to check a transaction from Genarc at Documanage and the connection is interrupted or does not correspond to the category of document.

• Upgrading ISE file copy error

  According to the upgrade to 1.2:

  Copy the Upgrade Pack towards the local disk using the copy of the ISE Cisco's CLI command: disk of ise-upgradebundle - 1.1.x - to-1.2.0.899.i386.tar.gz copyftp-filepath: / again, after copying the package to upgrade to the local drive, check that the size of the package upgrade from your local disk is the same as it is in the repository. Use the dir command to check the size of the entire upgrade in the local drive.

  When I try to run this command, I get the error message:

  ' % long command detected at ' ^ "marker".

  using the following command:

  ' copy the repository FTPDPZ ise-patchbundle - 1.2.0.899 - 1 - 82500.x86_64.tar.gz.

  I also tried to replace the repository + name with an IP address, with just the name of the repository and 100 other things.

  I tried to look at until a 'long command' is, but I come up with nothing.

  What is the good verbage to use this command?

  Hey David,

  It seems that you have been a little too long watching it, and accidentally hurt interpreted the guide! The "copy" command uses no configuration repositories currently in the running-config, so you must type it out as follows

  copy [email protected] / * //ise-patchbundle.etc.etc.etc.tar.gz drive: \.

  When you type out, there are more arguments to the command he knows he has to manage, then it throws the error '' long command. ''

  1               2               3                                                      4                                                            5

  copy of repository disk FTPDPZ ise-patchbundle - 1.2.0.899 - 1 - 82500.x86_64.tar.gz:.

  vs

  1                                                                     2                                                                                 3

  copy [email protected] / * /\ise-patchbundle.etc.etc.etc.tar.gz drive: \.

• Get a 'file corrupted' error while trying to copy files to the flash drive mp3

  * Original title: corruption of copy error

  I am trying to copy mp3 files to my music on a flash drive folder and I get an error "damaged file".  Only files is not corrupt, he plays very well on my system so WHY not copy?  I had dealing with "disc is dirty" and "file is corrupt" questions for THREE DAYS and, if that is what is happening with Windows 7 (the upgrade of Windows 7 is relatively new) so I'm going back to Vista!  Someone please help me with this.

  Hello

  I suggest you to go from the following link and check if that helps.

  Convert a hard disk or partition to NTFS format

  http://Windows.Microsoft.com/en-us/Windows7/convert-a-hard-disk-or-partition-to-NTFS-format

  I hope that helps!

• the installer doesn't Hum NOT file copied / directory Important install o once again error code 43

  the installer doesn't Hum NOT file copied / directory Important install o once again error code 43

  Hi dayanec84407565,

  Please see the following links:

  Error 43 - I can't download any adobe apps CC or creative cloud Manager

  Creative cloud, re-install-Dungeon error 43

  Error in downloading, installing or updating Adobe Creative Cloud applications

  Let us know if that helps.

• An internal software error occurred. Error code 8. LabVIEW: File permission error.

  I just changed a few contasts to controls in an FPGA core program, so there need to be recompiled.

  but it after compiling the program showed the error.

  An internal software error occurred. Please contact National Instruments technical support on ni.com/support with the following information:

  Error 8 has occurred to copy in nicrio_StockOutputVhdlAndInstantiation.vi-> nirviGetInstantiation___cRioStock_io.vi-> nirviGetInstantiation___nirviEIOImplementation_modGen.vi-> nirviGetInstantiation___nirviEIOImplementation_modGen.vi.ProxyCaller

  Possible reasons:

  LabVIEW: File permission error. You do not have the correct permissions for the file.
  =========================
  NOR-488: Error detected DMA hardware.

  C:\NIFPGA86\clntTmp\TensionCo~65_FPGATarg~A7_FPGABase~A1_eogs1jH0~18\Crio9426IoNode.vhd

  Ca person the reasons for which he showed an error.

  

  Hello

  I have a few questions,

  1. If you redefine your controls with constants, that you always get the same behavior?

  2. what equipment you try to deploy to? If it's a cRIO, have you formatted your controller and reinstalled the software for it?

  3. I did a little research and it looks like a potential problem may be with firewall/antivirus. Here is the document that explains that:
  http://digital.NI.com/public.nsf/allkb/D8D46FD4DBD1015786257540003B2DC6

  You have an antivirus installed on the computer? You can try to disable it and rebuild the bitfile?

  Kind regards

• Get copy errors whenever he asks the XP CD

  When I did a repair installation I got many errors of copy, but I made another with a freshly burned disc and this time only had a copy ICWCONN1 error. Ex_ or ICWCONN2. Ex_, one of the two.

  I have many components missing so I try to install via appwiz.cpl to install accessories and utilities that are missing, but it retains point out errors of various file copying, files randomly on the CD. I copied the CD to a folder on the HARD drive, but he refused to accept. What is going on? The files are not corrupt.

  The problem is resolved. Secedit.sdb is damaged.

  Running

  Esentutl /p %windir% \security\database\secedit.sdb

  cmd fixed the problem and got ran appwiz.cpl copy error-free. I am really annoyed with the fact that a repair installation has not set this property. In fact, the repair facility has been hampered by errors in copy because of this corrupt file. I hope and pray I made an installation repair is much more efficient on Windows 7.

• Volume shadow copy error after moving to MSATA SSD on R7 - 572

  A while back I cloned the value default 1 TB SATA drive on an MSATA SSD plugged into the slot unit MSATA.

  At the time I had been unable to conceive the MSATA as boot drive, while the original (also bootable drive) was in the system such that it does not appear in the BIOS from startup list.

  http://community.Acer.com/T5/S-and-R-series-laptops/cloned-SSD-in-Boot-Manager-but-not-boot-priority...

  As I did not need the 1 TB, I just removed and have used the system very well with just the MSATA SSD.

  Today, I tried to make an Image of Windows backup system and ran a (below) Volume shadow copy error

  Volume shadow copy service operation failed. (0x807800A1)

  Writer has encountered a transient error... (0x800423F3)

  I check all the main remedy online by ensuring that all VOlume shadow copy served are running, but without success. I feel that the fact that I'm on the SSD MSATA which was not visible in the list of the BIOS boot maybe being tied to the backup crashing.

  Anyone running the R7-572 on the MSATA port that is able to make a system image backup?

  Thanks for your comments

  It took me awhile, but I finally understood what was preventing the creation of the image of the system.

  Looking at the event viewer, he had a lot of mistakes, the first mistake we a CAPI2 with event 513, then it was a VSS error with event ID 8228 stating an invalid character in an XML file.

  Error says:
  Do not parse the XML file.
  Reason, an invalid character was found in text content.
  Line 0x000003c0
  Position 0x000009c8, the file below is damaged.
  0xc00ce508 error code
  Text problem<>

  Search through dozens of threads and try a number of bugs without success, I finally found one who mentioned their question came from bad characters in the names of partition after cloning with EaseUs Todo backup.

  It's the tool that I used to clone my drive to a SSD, I decide to check it out.

  The thread mentioned using GPT fdisk utility found on sourceforge, so I downloaded the tool.

  You just run the executable in administrator mode. Find how to use it was a little hard, but basically the commands below does the job

  0:-enabled disk 0, which is my drive.

  I - to view the information on each partition

  It will ask you the number. This allows you to see the names. Some of my partitions had some very strange names did not, we had a quote.

  I checked what names when used on another laptop and decided to appoint mine as follows (I think you can use any name)

  first 600 MB partion: database partition

  Second partition of 300 MB: EFI system partition

  Thrid 128 MB partion: Microsoft Reserved partition

  Fourth 205GB partition: partition database

  Fifth 17 GB partition: partition recovery

  To change the name of the partition, use the command

  c ask for the number of the partition, then the name

  Then save with

  w - written revisions and outputs

  I rebooted, tried the system image backup and no problem this time.

  I lost a full day on this topic, so I hope it can help someone else in the future

• Can not read the word file copied as a shortcut on a disc

  Format microsoft word copied as a shocut on a disk is not able to be read. An error message appears that the network connection or the driver that the shortcut refers to is unavailable.

  Please excuse my rudeness and gaiety that, but everything that you copied is the shortcut, not the file. If you attach the drive to your PC, it will find the file because the shortcut will direct you to the source file, but if you try to play the file on another PC the source isn't there.

  If you do not know where the file is stored pass on the original PC, right click the shortcut and go to properties and it displays the path of the target, because it is a Word file, the entire file is probably in the Documents. In the same box, you should be able to target location or find to open the file. When you locate the file copy on the external drive.

• The error message is im like error: 0xC004D401 Description: the security processor reported a system file mismatch error. After doing the update of windows Vista.

  There is a problem with your license so notifications will no longer appear
  You will no longer receive communications, including those concerning your license or activation.
  To try and fix this problem click on one of the links below.
  Error: 0xC004D401
  Description:
  The security processor reported a system file mismatch error.

  Vista Service Pack 2 (SP2) is installed?

  ==========================

  1. Download this diagnostic tool, save it to your desktop, then right click on the saved file and select run as administrator to run the utility: http://go.microsoft.com/fwlink/?linkid=56062

  2. once the race completed, click the continue button, and then click the copy button (on the Clipboard).

  Note: You can open a new file in Notepad, paste the contents of the Clipboard in it & keep for future reference.

  3. start your own, new thread in the following Microsoft Genuine Advantage forum and paste the results of the diagnosis of MGA tool in your post, and a clear description of your problem:

  http://social.Microsoft.com/forums/en-us/genuinevista/threads

  4 Troubleshooting specialist will analyze the data and recommend an appropriate solution.

• Files copied to external devices (USB/PHONE/CD-ROM) damaged when displayed

  Computer desktop running W7 SP1 with 64-bit system.  Files copied from the desktop to external devices are damaged when displayed.  Files can be JPEGs (photos) and or (e, g. XLS) data files.   Similar files copied from a laptop under W7 Service Pack One with a 32-bit system correctly screen.  Errors occur on the USB ports and CD-ROM drives used to copy the data.  This is potentially a problem of HD or something related to the operating system?

  Hi David,

  Thanks for posting your query on the Microsoft Community.

  As you mentioned that the files that you copy from desktop to external devices are damaged when displayed.

  This issue would have occurred due to a virus on your computer.

  I need some information to move forward.

  1. That you get an message\code error when you try to access these files?

  Maybe your computer got infected with a virus.

  So I suggest you view the Microsoft Help article and try the steps to find out if your system has a virus.

  http://Windows.Microsoft.com/en-us/Windows/does-computer-have-virus#1TC=Windows-7

  If you find that your computer has a virus please refer to the link below and follow the steps on how to remove computer virus.

  http://Windows.Microsoft.com/en-us/Windows/how-remove-computer-virus#how-remove-computer-virus=Windows-7

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  I hope this helps. Please let us know the status of the updates of your question. We will be happy to help you further.

• Who installed Procomm Plus - error message: file transfer error general error 119

  Anyone tried to install ProComm Plus more. Just could not get it to load fails on an iswinapi.dll of the GET the error message:
  Error - 119 target general file transfer error-check

  Hello

  It seems that the Symantec has designed this ProComm Plus application
  Why n t ask the company to Symantec for advice and support.
  The support guys generally have more experience with clean products

• File: \BCD error code: 0xc000000d ThinkPad S540

  Hello, I have a now 6 months and yestrday S540 when I restart the laptop, because to slow down, I got this error message:

  ------

  Recovery
  You are the PC needs to be repaired.
  Boot configuration data is missing some information required.
  File: \BCD
  Error code: 0xc000000d
  You will need to use the tools of recovery on your installation media. If you does not have any facility (such as a disc or USB device) support, contact your system administrator or the computer manufacturer.

  ---

  If youo knows how to solve this problem, let me know.

  Also in retail, computer laptop didn't strt, can't do anything.

  Thanks in advace.

  I have been using on the laptop's recovery partition.

  Whan starting press f11, you can try to fix it, or there is another solution, I have chousl check what it was.

  But check where it is mentioned that he keep your data.

• FTP .txt file copied correctly the cRio

  I use the 'FTP Get File.vi"to retrieve a .txt file of my CRio, which is then copied on my host.  The file is a delimited data tab.  The file copied all the data a except that the copy has a blank line between each set of data.  These additional lines take me to read the incorrect lines when the file is read in my program later with the "reading a spreadsheet file.  These additional lines come  I checked the original on the cRio file transfer via MAX and these lines do not exist.  Can someone tell me how to solve this problem?  Thank you

  If you look at the entries for the File.vi FTP Get, you will notice that there is one that says binary:

  

  By default, this is false, which means that it copies the data in an ASCII format.  Try a real constant of wiring to this entry.  It's the need for VxWorks and Windows use different end of windowing.  This difference is probably the reason that it is adding lines to it.