Firefox crashes even after a clean install of Windows

Similar Questions

• After a clean install of Windows Vista, Intel Wifi card is installed and activated, but does not detect the network.

  Wireless card not working after a clean install of Windows Vista

  I did a clean install of Windows Vista Home Premium on my HP Pavilion of 32 bits. I've completely updated Windows via Service Pack 2. Given that the clean install, my wireless card, Intel (r) Wireless WiFi Link 4965AGN, was not able to detect all the networks. The Wifi card is listed under NICs as being installed and activated. the hardware on my laptop Wifi switch is set on "on" and the light is blue, indicating that the card is working.

  I can connect to the internet if I connect physically my computer to the modem with an ethernet cable wireless, so the modem isn't the problem. Other computers can connect to the wireless modem, so my Wifi modem functionality is not the problem. The problem with my computer.

  I tried to uninstall the Intel driver and reboot my computer with the generic driver. Install the driver generic, but my wireless card has not always worked. I then ran an update of windows, nothing helps.

  I tried to install the "Intel® PRO /? Wireless and WiFi Link"drivers for Windows Vista (32-bit 13.1.1.1 the latest version and the previous version 12.4.4.5 32-bit) for the Intel® Wireless WiFi Link 4965AGN directly from the Intel Web site at http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Wireless+Networking&ProductLine=Intel%C2%AE+WiFi+Products&ProductProduct=Intel%C2%AE+Wireless+WiFi+Link+4965AGN. The map didn't always work with a driver.

  In addition to the pilots, I also downloaded a tool of diagnosis of Intel (Intel® PROSet /?) Utility of WiFi wireless connection for Windows Vista 32 -? Bit). Said diagnostic tool the WiFi card is not installed or enabled, however, Device Manager maintains that he is also installed and active.

  Is there a problem that causes Device Manager to say that all is well with the card, but does not map to realize that they diminish the radio signals? Everything's fine, diagnostic, it just does not detect networks around him. Help, please.

  Hello

  The on/off switch actually works?

  Since it is an internal adapter to ensure it is enabled in the settings of configuration/F2 (BIOS/CMOS) often like you
  Start - so look at the screen.

  Have you tried the computer on other WiFi networks? You had a WiFi type problem before the
  Re-install of Vista?

  ---------------------------------------------------------------------------------------------------------------------

  Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
  Update your WiFi drivers on computers. How you are positioned in the router? Are there
  obstacles in the path?

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• HP Pavilion - 15-p264na: audio beats does not open after a clean install of windows 8.1

  Hello

  After a clean install of windows 8.1 the audio beats does not open.

  It appears in the control, but when I click on it nothing happens.

  I have sound, and everything seems to work ok, but I'm curious to know what happened.

  When I go to Device Manager and select audio, video controllers and game, there are 2 features 1 is AMD high definition audio and the other just says high definition audio device.both drivers are up-to-date.

  I look through the forums CIHI and I tried some of the links for the drivers of the itd, but they will not install.

  Any help would be appreciated

  Hello

  Download and reinstall the Realtek HD Audio software at the following link.

  http://ftp.HP.com/pub/SoftPaq/sp69001-69500/sp69164.exe

  When the installation is complete, restart the laptop.

  Kind regards

  DP - K

• Does not not on M6-1091se after a clean install of Windows 7 first 64-bit home for fingerprint reader

  Does not not on M6-1091se after a clean install of Windows 7 first 64-bit home for fingerprint reader

  Hello

  Please try:

  http://ftp.HP.com/pub/SoftPaq/sp59501-60000/sp59664.exe

  Another option: click on the following link and click Search now :

  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=4063&LC=en&cc=us&DLC=en&sw_lang=&product=5306751#N2316

  Kind regards.

• After the clean install of windows 7, it gives an error saying that there is a problem in the hard drive.

  * Original title: hard drive

  I have a lenovo laptop, processor Intel i3, 500 GB hard drive. After the clean install of windows 7, it gives an error saying that there is a problem in the hard drive. I ran chkdsk looking for bad sector and its display 6000 KB in bad sectors. After completing the audit when it began to restart its stuck when the windows logo appears. What should I do? Reinstall the windows help?

  Run the hard drive HD diagnosis extended CD scan manufacturer to know with certainty the State of the reader.  If your brand has no bootable diagnostics in the link, use Seagate Seatools burned onto CD or SeaTools for a USB key .  Follow this with a full check disk command from the installation media kicked prompt know with absolute certainty the State of the reader.  If he repeated the errors after you run the two tests twice, I replace it or at least keep everything backed up in real time.

  If by chance the drive past diagnosis then compares the steps you've done with the best possible Clean install Windows 10 in the link, you can do more if it varied too - especially if the partitions were not deleted during install.  If you do then I additonally run own Diskpart command command line of the punt media accessible to the first screen after startup by pressing SHIFT + F10 keys, or through the repair your computer on the second screen.

• Stuck at 0% - even after a clean install Windows Update

  Hi guys,.

  I am aware that there are various other posts on the same question, however, I think mine is unique.
  I have 144 updates to Windows that will not download and will remain at 0%. I did everything I could to try to resolve this issue - including making a refresh and a clean reset/install of windows 8, but none of it worked.

  I am aware that there may be files that are corrupt, but if this is the case, would not have done a clean install/reset windows to fix this?

  "I tried different methods including attempts to install the updates one at a time, but this does not work either, they all remain at 0% complete.

  I'll be very grateful if this has been resolved that it is forbidding me download windows 8.1 and reserving my copy of windows 10!

  Thank you very much
  :)

  Try this:

  1. open a command prompt

  2. type the following command and press ENTER: DISM.exe/online/Cleanup-image /Restorehealth

  3. once the order is completed, the results here and try to check the updates again

• After a clean install of Windows 8, I can't get three monitors to work

  I did a clean install of Windows 8 pro.  I have a Dell T1500 with over-pants V4800 graphics.  This machine previously had Windows 7 installed and works with the ATI driver.  With Windows 7, the three monitors worked without problem.  Now, with Windows 8 installed I can't get two monitors to work.  I use the more updated driver for Windows 8 for the map on the website of AMD.  The third monitor can be seen on the page of the screen resolution, but I cannot "extend desktop...". "the third arch.  When I try to do so it gives me a message saying

  "The display settings could not be saved.  Please try another combination of display settings. »

  All three monitors are the same, Dell P2210.  I tried different resolutions. I tried the driver I was using on Windows 7, I uninstalled the driver and adapter repeatedly.  I installed all the drivers from AMD with the extras (hydravision, etc.).  I used just the default Windows drivers. I have change the placement of the monitors on the video card, but few matter where I plug them in, only two works.  All monitors are operational.  I even tried different monitors.  All this with no result.  I tried to use the Catalyst Control Center.  He sees the third monitor but just shows it as being disabled with no way to enable that I see from in the Catalyst Control Center.

  It is the last obstacle for me to fully use this machine to Windows 8.  I'm puzzled.  I have read many other forums.  I've heard of this problem with Windows 7 as well so I don't know that it's specific to 8 but could very well be.  Yet once I had Windows 7 with three monitors with the same card.  Contribution to this issue would be greatly appreciated.

  I had this problem on a Lenovo three installation of the monitor using the integrated display laptop, a monitor outside the mini HDMI and a third follow out of the HDMI Port among Replicator.

  In the end, it's a simple solution.  When you go to display settings, all three monitors not reimbursed up to 1920 x 1080 and configuration could never be saved - however the 3rd monitor only supported by 1680 x 1050, which is the resolution (recommended).  After changing the 3rd monitor for the resolution recommended, I was able to save the configuration to display > screen without problem resolution.

  I don't know why the resolution not supported has been set default to-after selecting the right pair, there is now no option to go to the highest resolution not supported on this screen.

• After a clean install of Windows 7 pro on the Pavilion dv6-6147tx I have no access to the Universal USB po

  After a clean install of Win 7 pro on Pavillion DV6-6147tx I have more universal access to USB ports.  I can't find a driver to download HP downloads or disk 3 recovery disc. 3 USB ports o.k.

  I finally solved my problem of usb 2 with a NEC driver downloaded from HP believe it or not... He took a large sum oh hunting via other websites. My contact with the HP service is a waste of time.

  The pilot is SP47677. EXE from HP, it does wonders, but it does not appear on a search in the HP website.

  I solved my problem.

• Missing Ethernet, network controllers SM Bus and PCI device after a clean install of Windows 7 64 bit

  Hello friendly folk,

  I got a used HP Pavilion G6 - 1C40CA.

  There was a clean install of Windows 7 Home Premium 64-bit.

  After searching around online, got a hint of what to do.

  For Device Manager are missing or not that there is not (small yellow exclamation triangle):

  Ethernet controller (Hardware ID: PCI/VEN_10EC & DEV_8136)

  Network controller (Hareware ID: PCI/VEN_14E4 & DEV_4727)

  PCI device (Hareware ID: PCI/VEN_10EC & DEV_5209)

  SM Bus controller (Hardware ID: PCI/VEN_1022 & DEV_780B)

  As well as to find good downloads, I know not to order that I should be their installation (if there is a specific order at all), and if I have to restart every time that I have install something again.

  If someone could be kind enough to drive me very precisely by the process? Pretty please? ^_^

  Hello:

  The first pilot, you need to install is for the smbus controller.

  Download and install the amd chipset drivers and restart.  You want the first file on the Web page.

  http://support.AMD.com/en-us/download/chipset?OS=Windows%207%20-%2064

  Here's the rest of the drivers you need in the order you posted the material ID's, and you can install them in an order any that you like...

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-100084-1&cc=us&DLC=en&LC=en&OS=4063&product=5173139&sw_lang=

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-95652-1&cc=us&DLC=en&LC=en&OS=4063&product=5173139&sw_lang=

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-100083-1&cc=us&DLC=en&LC=en&OS=4063&product=5173139&sw_lang=

• No restore factory after a clean install of Windows 7

  Factory support key F11 RnR restores after a clean install of win7?

  I did a new install of win7 and installed a RnR last on my T410. When I tried F11 RnR, there is no option to restore with. My SYSTEM_DRV and Lenovo recovery xxxx exist and are suitable for all the files in them.

  I have recovery disks, but I just what to see if restore factory F11 works on this path.

  Fix. I had already understood what you were doing.

  I'll say it simple as I can:

  (1) installed at the factory

  The secret is windows 7 added windows re (recovery of win7 to the mix environment). Lenovo plant reorganizing this to factory support. This has created a hidden from the factory restore boot entry.

  (2) your installation "sideways", IE, cram lecteurC.

  This wax installation tips from lenovo. That is to say, no factory entry to move to the RNR standalone.

  (3) any property. do not delete anything. (such as SYSTEM_DRV).

  ==

  You have a dead now at the new disk space.  This works. Large.

  Use RNR and backup every week in a place (external). I know that it was not fun, but has been a learning experience.

  ==

  To clarify: (confusion)

  RNR is the main big daddy.  This is the main task is to rescue by using a backup RNR. Recovery (factory) is a subset, not exactly. This just transfers control to another entry for starting a recovery plant stuff. Thus, Rescue and Recovery.  I answer all the time about it. Yes, they look different, they are.

• Re-install Acrobat after a clean install of Windows 7

  I have a problem of software (Windows) on my PC that requires a clean install of Windows 7. What to I need to re-install Acrobat on the PC after the clean operating system installed? I have an Adobe account that lists the programs that I recorded as well as the serial numbers. What is the procedure to reinstall Acrobat?

  If you have access to the still of machine, disable the application by opening and by selecting help-> Deactivate.  Later, after the new system is in place, you can download and install.

  Acrobat XI, X - http://helpx.adobe.com/acrobat/kb/acrobat-downloads.html

• error message iTunes displays locked drive, itl locked files, or do not have administrative privileges on the PC after a clean install of Windows 10

  Yesterday I did a clean install of Windows 10 on my PC with a backup of the hard disk external. I downloaded iTunes, but get an error message that the drive is locked, the .itl files are locked, or I don't have administrative rights to these files. I deleted and reinstalled the PCI DSS several times correctly in the PCI slot hoping that would be a solution, but to no avail. I am the only user on this computer and do not have administrative rights. Any help you can offer will be appreciated. Thank you

  This can help (from turingtest2):

  Fix iTunes for Windows security permissions

• Satellite P305-S8820 - FN key not working after a clean install of Windows 7

  Hello

  I have a Toshiba Satellite P305-S8820. I recently did a clean install of Windows 7. I loaded the value Toshiba driver pack and the trackpad driver but still cannot get the trackpad or press FN to work.

  Any ideas?

  Hi taxwiz,.

  I think that the forum already contains hundreds of discussions about this so why you n t use the forum search?

  Anyway, you need the latest version of Toshiba Value added Package and utility Support Flash Cards.
  Try to also restart Toshiba Flash Cards (start > all programs > Toshiba) and repeatedly press the FN keys.

• Recovery Manager HP dv7-1130el after a clean install of windows 7

  I'll do a clean install of windows 7 32 bit from Vista Home premium 32-bit.

  I would like to know if the Recovery Manager will continue to work, or might have a problem.

  I found on the page of the HP software for windows 7 two patches for update Recovery Manager:

  sp45823.exe who makes an upgrade (but not a clean install) and update generic sp44455.exe.

  This second patch help me avoid problems later with Rec.Man when I do the clean install?

  How should I do?

  Could someone tell me a Board.

  Thanks in advance.

  Make your recovery Vista using Recovery Manager disk before installing 7. then it won't matter to have a functional recovery Manager since it is only to reinstall the original OS and programs. It has no function in windows 7 other than to go back to Vista, which can be done with your if necessary recovery discs.

• After a clean install of windows 7 Home premium 64-bit, dvd will play not [scrambled] and computer is crashes sometimes and I have to force the reboot.

  I have windows 7 Home premium 64-bit, which has totally collapsed.  By mistake, I installed my operating system 32-bit vista on it.  I bought a new windows 7 Home premium operating system and installed.  I did a clean install after formatting the hard drive [the did twice].  Now dvd will play not [scrambled] and computer is crashes sometimes and I have to force the reboot.  I saw the reference to System 32 on restart options.  Help?

  Original title: operating system 32 and 64 bit

  Have you installed Windows 7 device drivers for your make and model. If this is not the case, then go to the support web site factory and download Windows 7 drivers to a folder on your PC and then first install the drivers for the card mother/chipset, followed by USB, SATA, LAN, Audio and all other pilots.

  Find the website of your computer manufacturer support.
  http://Windows.Microsoft.com/en-us/Windows/help/contact-support/computer-manufacturers

  How do you know if you have a 32 bit or bit 6 vrsion of Windows installed:

  http://support.Microsoft.com/kb/827218

  BIOS updates: you should check to see if there was one, or sometimes several updates BIOS for the motherboard. Read (if provided) which solves the update. Sometimes a newer BIOS update will fix the problem. Read the instructions on how to your BIOS update/flash very carefully and be more you understand the process. There is a risk of a bad flash/update occurs which can make your system unbootable.

  Also check the download site of the manufacture of the graphics card for the latest Windows 7 drivers for your card.
  ATI: http://support.amd.com/us/gpudownload/Pages/index.aspx
  NVIDIA: http://www.nvidia.com/Download/index5.aspx?lang=en-us

  J W Stuart: http://www.pagestart.com