Flash Builder on Mac 4.6 will not start

Similar Questions

• Illustrator for Mac trial CC will not start

  I downloaded and installed the trial version of the CC for Mac Illustrator. When I try to launch it. the icon flashes for a few seconds, then disappears. The application will not start.

  Install fonts Verdana and Tahoma from Microsoft.

  Mylenium

• Mac Pro 2009 will not start, no edge

  On Thursday, June 16, I sat to use my Mac Pro early 2009. I noticed that my Mac would not wake up by mouse click or the SPACEBAR on the keyboard. The led on my Mac, so I immediately thought that it was a problem with the graphics card.

  I force shut down the Mac by holding the power button. I waited 10 seconds and turned on my Mac back, everything was fine and I worked on my Mac for 3 hours.

  Last night 18 June I sat watching television when I heard the ringtone on my Mac Pro, I realized was a reboot. I went to the wire and connected and everything seemed fine. However later in the evening, I noticed a flashing LED on one of my two monitors. Once the Mac was on (fans spinning) but no signal to the monitor.

  I made another force off now the power button on Mac, but now when turn on the Mac there is no boot chime or control signal.

  I upgraded the graphics card to an AMD Radeon Sapphire HD 7950 in April 2013.

  Any advice would be much appreciated as I'm in the middle of a big project.

  Could also be a Mac Pro RAM chip inyour failure, sounds almost identical to a question I've had recently, I found the missing question when I removed the memory card.

  If one of the pair of cards, you will need to remove two cards.

  Try taking the memory OUT n test each module one at a time. Also check RAM editing maps, if none of the four lights on the two cards is turned on it idicates a defective module.

• I nned to know the procedure I use to get can Mac 2008 Desk top that will not start. I don't know how to connect two computers, my portable Mac Air 2013 on my desk, now I need to know how get the workstation files in order to appear on my mac air so I can

  Does anyone know how after I connect to my office 2008 Mac (which will not start.) to my computer laptop (2013 Mac Air). What are the steps that I need to know to get the Desktop files is displayed on my mac air so I can copy files to your laptop, especially my Itunes folder.

  Thanks Jerri

  If you can't get the iMac began and ongoing implementation, you will not be able to use the target disk Mode:

  https://support.Apple.com/en-us/HT201462

  Then the option is to take the iMac HARD drive, install it in an enclosed, and connect the HARD drive to the MBA via the USB port.  If the HARD drive is recognized, you can copy the data out of it.

  Ciao.

• Computers button just flashes and the computer will not start

  Computer on button just flashes continually and the computer will not start.  I unplugged everything and put it back together.  Same thing.  Nothing.  Monitor is on, but nothing on the screen, of course, because the computer does not start at the top.

  Computer on button just flashes continually and the computer will not start.  I unplugged everything and put it back together.  Same thing.  Nothing.  Monitor is on, but nothing on the screen, of course, because the computer does not start at the top.

  Hey Bowers

  you get a splash screen on startup with an acer for hp dell etc. or the logo of the motherboard

  otherwise, it would seem that you have a hardware problem

  Contact the manufacturer of the computer or a local reputable computer repair workshop

  Walter, the time zone traveller

• I have LR 6 (upgrade LR 5and4) installed on Windows PC and switch to Mac. It will not install on Mac since the earlier version is installed. Is there a solution?

  I have LR 6 (upgrade LR 5and4) installed on Windows PC and switch to Mac. It will not install on Mac since the earlier version is installed. Is there a solution?

  Update should allow you to enter the serial number of the previous version during the installation

  If this does not work, you must communicate directly with Adobe

  Chat/phone: Mon - Fri 05:00-19:00 (US Pacific Time)<=== note="" days="" and="">

  Don't forget to stay signed with your Adobe ID before accessing the link below

  Creative cloud support (all creative cloud customer service problems)

  http://helpx.Adobe.com/x-productkb/global/service-CCM.html

• 12 elements will not start on Mac

  Hi I used Photoshop elements 12 on my Mac OS X El Capitan for many years, but today it will not start. I get an error message "Photoshop elements 12 editor quit unexpectedly" and told me to click on resume to start again... but by clicking reopen comes back to the same error message?

  Frank

  Hi, Frank. What is the version of the App Store?

  You probably need to reinstall. Your download should always be available in the Mac App Store under "purchases".

  Apple has had problems with security certificate expired affecting all applications downloaded from the Mac App Store. Here's a solution that worked. Give it a try by following each step:

  I had the same problem on the Mavericks and your suggestion worked for me.  FYI, I deleted the items, empty trash, disconnected from the App Store, restarted the computer, signed in to the App Store, then downloaded items.  I use OS x 10.9.5 and 11 elements.  Hope this helps!

• G5 will not start. LED light on. Fans before working.

  Early 2005 G5. running 10.5.8.

  G5 will not start. LED light (no flashes not but solid). Fans before working. Rear fans blowing not. Cleaned up the dust. A exploded during a down and will not restart. Any thoughts? Is that a bad diet? What I would do. Thanks for any help. I love this old computer and hope to keep fixed and working.

  Sam

  Some of the fundamental things include the pram/clock battery replacement

  since they may be dead; then with a power failure, sometimes the Mac

  do not restart. Usual power management unit & reset NVRAM/PRAM are

  methods that sometimes also used as a troubleshooting measure.

  • Reset the Mac chip power management: (see SMU)

  http://www.thexlab.com/FAQs/resetpmchip.html

  • How to reset NVRAM-LANDAU on your Mac - Apple Support

  A hard reset can sometimes be used, where the power is disconnected

  the logic board and power removed from grill; Then push the Start button / stop.

  (But maybe not. Several PowerMac computers, I had, some people found this helpful)

  You may also remove and reposition cards and other items

  the inside of the case, to be sure they are connected properly. Be sure to not

  In short anything, due to the static load or residual power in the circuits.

  The hour is late here, so I'm not going offline; If all goes well a battery original or novel, etc.

  can help to put it on again. Also sometimes the power supply has some faulty fans,

  circuits or capacitors, so they can be troublesome to repair or replace.

  Good luck in this case!

• Printer HP Photosmart will not start

  I am not necessarily in a hurry for an answer.

  I use a HP Photosmart 7260, S/N CN38Q2B0ZQ, Q3005A printer, model # SDGOA - 0372, with a Mac OS 10.5.8.  Printer blinking red and will not start.  There is no driver for the printer.  I had for a long time, never had a problem.  What should I do?

  Red flashing red in the light, I think that your machine has no status. If it flashes in the light of memory card, then there is an error with the memory card. Unfortunately, the machine is 7 years old and has lived a long life that printers are concerned. It would not be surprising if it has passed. This doesn't seem to be a hardware problem.

• Photoshop CC 2015 (Norwegian version) will not start. The following message: Adobe Photoshop CC has stopped working.  A problem caused the program stopped fungeresom correctly. The program will be closed and you will be notified if a solution is av

  Photoshop CC 2015 (Norwegian version) will not start. The following message: Adobe Photoshop CC has stopped working.  A problem caused the program stopped fungeresom correctly. The program will be closed and you will be notified if a solution is available.

  reset your preferences-

  Acrobat: http://help.adobe.com/en_US/acrobat/X/pro/using/WS58a04a822e3e50102bd615109794195ff-7feb.w .html

  Adobe media encoder: https://forums.adobe.com/thread/1713540

  Legacy: http://helpx.adobe.com/after-effects/using/preferences.html

  Bridge: https://helpx.adobe.com/bridge/kb/troubleshoot-errors-freezes-bridge-windows.html

  Dreamweaver: https://helpx.adobe.com/dreamweaver/kb/restore-preferences-dreamweaver-cs6-cc.html

  Flash: http://helpx.adobe.com/flash/kb/re-create-preferences-flash-professional.html

  Illustrator: http://helpx.adobe.com/illustrator/using/setting-preferences.html

  InDesign: https://forums.adobe.com/thread/526990

  Lightroom: https://helpx.adobe.com/lightroom/help/setting-preferences-lightroom.html

  Muse (mac): https://forums.adobe.com/thread/1246022?tstart=0

  Photoshop: https://forums.adobe.com/thread/375776

  Photoshop elements: https://helpx.adobe.com/photoshop-elements/kb/preference-file-locations-photoshop-elements .html, http://www.photokaboom.com/photography/learn/Photoshop_Elements/troubleshooting/1_delete_p references_file.htm

  elements of first: https://helpx.adobe.com/photoshop-elements/kb/preference-file-locations-photoshop-elements .html

  First pro: http://www.mediacollege.com/adobe/premiere/pro/troubleshooter/trash-preferences.html

  If that fails, uninstall, clean (http://www.adobe.com/support/contact/cscleanertool.html) and reinstall

• Updated the macbook pro of el capitan and now will not start. Instead, I get the error message "your computer restarted due to a problem". Someone at - it suggestions on how to solve this problem?

  Updated macbook pro today for the latest version of el capitan and now will not start. Instead, I get the error message "your computer restarted due to a problem". Someone at - it suggestions on how to solve this problem?

  It would be helpful to post what the screen says.

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  https://support.Apple.com/en-us/HT201295

  Subject of memory NVRAM and PRAM

  https://support.Apple.com/en-us/HT204063

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  https://support.Apple.com/en-us/HT201262

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  https://support.Apple.com/en-us/HT201314

  -If it is repairable reinstall the OSX

  How to reinstall OS X on your Mac - Apple Support

  https://support.Apple.com/en-us/HT204904

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

• Satellite A500 will not start

  I have an A500 on 12 months old that will not start.

  The battery light shows white and power on AC light is on as well.
  When button "power on" is pressed and released the laptop IT flashes briefly then the battery lights up orange briefly and the light goes out.

  Battery has been divested of the case and it was completely discharged and it still will not with or without the battery. He has been connected to a different power of toshiba with the same results.

  The difficulty feeding saw two days ago. After that about 10 minutes to load then turned on.

  I saw a post where the guy was acquitted of the internal cmos memory and he ends up - which would have something to do with it?

  Any clues anyone?

  Hello

  I think that it s something wrong with the motherboard or a part of the motherboard.
  The point is this laptop should turns on even if the battery is empty and the power adapter is plugged so maybe it s something wrong with the memory supply or electronic power on the motherboard.

  I recommend you check the parts of memory first. Remove a module and try to start the device using that one module.

  Of course this can not help you too... so in this case, it could be a severe motherboard issue...

• Nine NB100 will not start

  Hello

  I just bought a Netbook NB100.
  After unpacking, I tried to turn it on, but it will not start

  When I put the charger in it gives a rattling sound very rapid for a few seconds and then stops, and also the sign of the battery flashes for 5 seconds and then turns off.
  When I press the button start nothing happens.

  Any help appreciated. So was lookiing forward to this

  Thank you

  Hello

  Remove the battery, connect the AC adapter and try to turn it ON.
  I didn't understand exactly what happened. But I hope you didn t turn it on for the first time without adapter.
  It is logical that the laptop must be put in power supply and after short time you can run it for the first time.

• Re: Satellite L300-1AS will not start

  Hi all

  Now my L300 will not start not (windows (Vista).
  It shows a blue screen saying that windows has been shut down and to check the installation of new hardware or software.
  There is no new hardware or software. He suggested to disable the bios memory options (I don't know how to do this) and suggests to start in safe mode to remove or disable components.

  The laptop does NOT start in any mode not to mention safe mode, repair mode that brings back me to the blue screen as described.
  I bought a Toshiba Recovery disk (a single disc happened?) that begins its process then two locks of "select a language to move forward" or detects an error and request I have "press any key to continue' what I'm doing, it then displays X:\windows\system32 > with the cursor flashing at the end of > and does nothing more , its been like that for 5 hours now... I'm supposed to type something in or I am looking at a new hard drive?

  Suggestions for a greatly appreciated numpty (outside to let computers alone numpty you of course!)

  Thanks

  Colin

  Hello

  Yes, the recovery disc's one disc it s DVD ;)

  Return to be issued;
  I think that it s material related since the recovery disk should work for sure.
  The blinking cursor can be related to a faulty memory or HARD drive.
  Both should be checked.

  You could remove a memory module and might try to power the device using a single memory module in a slot.
  Of course, the best would be a use of two new modules

  The HARD drive can be checked using a tool called Drive Fitness Test (it of free use google to find it)

• Equium L10 will not start

  Please help - my Equium L10 will not start.

  Power supply is OK. When the power is connected the orange battery light comes on. I press the power button the green power light turns on momentarily (literally a Flash), then both the Green and orange lights out with orange alone returning it on about 2 seconds later.

  Else does nothing - no fan activity, no hard disk, no activity of the screen activity, no other light - you get the picture!

  I tried the following:
  Removed battery and tried to start with AC power not only - no joy
  Removed AC power and I tried booting with battery only - no joy
  Barrette of RAM removed and reinstall - no joy

  Does anyone have ideas before considering a tech? Suggestions (with the exception where to paste!) would be welcome.

  Kind regards

  Gary C

  Hmm .He doesn't sound good. For me, it looks like a motherboard problem. It is maybe something wrong with electronic power to the Board of Directors of s. But not for sure.

  What you can do is to remove the battery and unplug the power adapter for a while.
  Wait about 20 minutes and connect the battery and adapter for the laptop. Then try turning on the laptop computer.
  If this does not help I recommend contact the ASP technician, because I don t think you will be able to know what's exactly wrong.

  So I hope that the technician can find the fault quickly and can solve this problem.

  Good luck