For IPS 7120

Similar Questions

• The switch configuration of 6500 catalyst for IPS Inline the METHOD works

  I understand how to configure the switch Catalyst 6500 so that the monitoring of ports are access ports in two VLAN separate operation online.

  However, I don't see any document that describes how the desired VLAN traffic gets forced through the IPS.

  "Promiscuous" mode, you can use copy/capture VACL and forwards traffic wished the METHOD of analysis. I don't see how to get traffic desired through the IPS.

  Note that the 6500 host is running native SXE IOS 12.2 (18).

  Thanks for any help.

  A transparent firewall is a pretty good comparison.

  Say you have vlan 10 with 100 PCs and 1 router for the network.

  If you want to apply a transparent firewall on this vlan you can put not just the Firewall interface on vlan 10. Nothing would go through the firewall.

  Instead, you need to create a new vlan, say 1010. Now you place the Firewall interface on vlan 10 and the other on the vlan 1010. Nothing is still going through the firewall. So now move you that router from vlan 10 to vlan 1010. Everything you do is to change the vlan, IP address and the mask of the router remain the same.

  The firewall transparent bridge vlan 10 and vlan 1010. The SCP on the vlan 10 ae is able to communicate and through the router, but must go through the transparent firewall to do.

  The firewall is transparent because there no IP Route between 2 VLANS, instead, the same IP subnet is on the VLAN and the transparent firewall ensuring the beidges between the 2 VLANS.

  The transparent firewall can do firewall between the SCP on the vlan 10 and the router on vlan 1010. But PC has vlan 10 talks for PC B on vlan 10, then the transparent firewall does not see and cannot block this traffic.

  An InLine sensor is very similar to the transparent firewall and will fill between the 2 VLANS. And similarly an InLine sensor is able to monitor InLine between PCs traffic on vlan 10 and the router on vlan 1010, but will not be able to monitor the traffic between 2 PCs on vlan 10.

  Now the PC on the other vlan and the router on a virtual LAN is a classic deployment for the sensors online, but your VLAN need not be divided in this way. You can choose to place some servers in one vlan and desktop to another vlan. You subdivide them VLAN to whatever the logical method for your deployment.

  Now for the surveillance of several VLANs the same principle still applies. You can't control traffic between machines on the same vlan. So for each the VLAN that you want to analyze, you will need to create a new vlan and divide the machines between the 2 VLANS.

  In your case with Native IOS, you are limited to only 1 pair of VLAN for InLine followed, but your desired deployment would require 20 pairs of vlan.

  The IPS 5.1 software now has the ability to manage the 20 pairs, but the native IOS software doesn't have the ability to send the 40 VLAN (20 pairs) to the JOINT-2.

  Changes in native IOS are in testing right now, but I have not heard a release date for these changes.

  Now cat BONES has already made these changes. So here is a breakdown of basic of what you could do in the BONE of cat and you can use to prepare for a deployment native IOS when it came out.

  For VLAN 10-20 and 300-310, you want monitored, you will need to break each of those VLANs in VLAN 2.

  Let's say that keep us it simple and add 500 to each vlan in order to create the new VLAN for each pair.

  Therefore, the following pairs:

  10/510, 511/11, 12/512, etc...

  300/800, 801/301, 302/802, etc...

  You configure the port to probe trunk all 40 VLAN:

  set the trunk 5/7 10-20 300-310 510-520 800-810

  (And then clear all other vlans off this trunk to clean things up)

  In the configuration of JOINT-2 create the 20 pairs of vlan inline on interface GigabitEthernet0/7

  NW on each of VLAN original 20 leave the default router for each LAN virtual vlan original to the vlan 500 +.

  At this point, you should be good to go. The JOINT-2 will not track traffic that remains inside each of the 20 VLAN original, but would monitor the traffic is routed in and out of each of the 20 VLAN.

  Due to a bug of switch, you may need to have an extra PC moved to the same vlan as the router if the switch/MSFC is used as the router and that you deploy with a JOINT-2.

• Cisco asa 5585 syslog options for ips?

  We have CISCO ASA 5585 with a separate module for the IPS, I want to know what are the options for configuring syslog? Its almost impossible to find; and there are some forums on the internet that says cisco ips store the logs in native format / owner and cannot be exported.

  Please provide details

  Thank you.

  Click on the following link

  https://supportforums.Cisco.com/document/47881/SDEE-and-IPS

• How do a search for IPS inside a html tag for a string?

  I need to make the search for cisco IPS of the chain eb 03% 59% eb % 05% e8% f8% ff % ff % ff % 49% 49% 49 inside any *.html

  I tried the http service (ask Regex) and AIC http (Msg body Patten) but no luck

  Thank you

  Using IDM

  Configuration > definition Signature > Assistant personal than Signature

  Select TCP as the Protocol to inspect >

  Click on the single TCP connection option button >

  Select other as the type of service >

  Enter the parameters for signature >

  Select your action event

  String Regex class enter eb 03% 59% eb % 05% e8% f8% ff % ff ff 49% 49% 49%

  Enter 80 in the field of service Ports

  M.

• Release notes for IPS Signatures available via a direct URL?

  Is there some URL, I can refer to work colleagues, so they can review the current and any of the other IPS signature release note (s)? The only way I found to get there is through the slow multistep download section, and a few colleagues, I do not know who find acceptable. You know how some desktop environments can be, right?

  Thank you.

  The answer depends on what exactly you are willing to provide.

  If you are looking for just the main part of this file that lists the signatures of new and modified, then you can download the latest being and he has all the information for the latest sig updates several:

  Here is the link to the file Readme S407

  http://www.Cisco.com/Web/software/282549755/27019/IPS-SIG-S407.Readme.txt

  You can look down and find the GIS information all the way back to S339.

  If you are looking for a quick way to your colleagues see the list of updated signatures to the forthcoming GIS Day, then check out the Archive of Bulletins of Cisco IPS Active update on cisco.com:

  http://Tools.Cisco.com/Security/Center/bulletin.x?i=57

  Each ballot will list the signature changed or new in the update of the signature.

  They are marked instead of updating GIS marked this day.

  If you want files real readme for updates of signature, then you could also try to go to this page:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/ipsmc-ips5-sigup

  It's the page where signatures update files can be downloaded manually for virtual machine management tools or CSM.

  The readme in signature files posted here are also the same for the sensor.

  The advantage of this page, is that all files can be at least but a single page.

  NOTE: Older Readme files can be found in the archive for the above page location:

  http://www.Cisco.com/cgi-bin/tablebuild.pl/ipsmc-IPS-sigup-arch

  Hope one of these options will work for you.

• Latest package (pkg) for IPS signature

  Hello

  Really need a helping hand to understand what are the .pkg files?

  • I have download a last signature packet - IOS-S573 - CLI.pkg
  • I copied it to Flash on a router to test and I can access it via the SDM
  • I have setup my router and put in all the config for FPS

  Router with IOS-S573 - CLI.pkg as the basis of active signatures

  #sh ip ips signatures

  Builtin signatures are configured

  Signatures were last load of flash:/ips/IOS-S556-CLI.pkg

  Total active Signatures: 0

  Inactive Signatures total: 0

  But if I change the router to use the file 256MB.sdf from cisco, I see 537 signatures

  #sh ip ips signatures

  Builtin signatures are configured

  Signatures were last load of flash:/ips/256MB.sdf

  Total assets Signatures: 537

  Inactive Signatures total: 0

  Q. What is the best way to have the signatures up-to-date on the router? I would have thought that it would be to use the last file namely IOS-S573 - CLI.pkg

  Kevin,

  I answered a similar question from another user a minute ago. Please read the link below. It should dissipate most of your confusion. (Once you have read the link then keep reading below).

  In addition, if your router is able to use 5.x signatures, then you don't have user control"

  Flash:/IPS/iOS-S556-CLI.pkg. "It's for the signatures of version 4.x, which I think is using your router. You would load the signature by typing "copy flash:/ips/IOS-S556-CLI.pkg idconf." Which will cause the signature compile. You'd be off to the races after that. (Remember to read the link to the other post, I presented. This will give you exactly the way that everything is set up.)

  After the back if you have other questions. Nice day. Nice day.

  https://supportforums.Cisco.com/message/3418935#3418935

• HOW TO SET UP FOR IPS PROMISCOUS MODE 4270

  I have IPS4270 and I want to configure promiscous mode. I have configured my IPS, but he doesn't get any traffic to vlan. Please how can I configure my IPS to promiscous mode. What would be the ony my switch configuration?

  Thank you and best regards

  Edwin

  Assuming you want to collect the Gi01 intefaces across 20 traffic and send traffic to yoru 4270 on Gi0/21 intergace

  the source monitor session interface 1 Gi01 /-20 rx

  control interface of destination session 1 Gi0/21

  -Bob

• Syslog for ips configuration

  Is it possible to configure IP addresses to send messages to the syslog server. If yes then ask to share the steps you

  Yes, is possible to configure IP addresses to send syslog messages to a syslog server.

  Configure the command:

  Enable logging

  timestamp of the record

  asdm of logging of information

  forest management - ipaddress inside device id

  logging inside the 192.168.3.10 host

  Debugging trace record

  1st & 5th rom up-down control are necessary. rest depends on your condition to capture packets in the syslog server. all these commands are inserted automatically if you configure syslog Device Manager.

  rate if this can help...

• For ASA IPS modules

  Hello

  I would ask you to help learn p/n for the IPS/IDS modules in:

  -ASA 5510

  -ASA 5515 X

  I would like to buy our dealer, but he asks that no part numbers, that he can't find them...

  I know that for ASA5510 was AIP-SSM-10, but it currently is EOS. ASA 5515 X has software module, but I can't find this p/n.

  Concerning

  Hi Michal,

  IPS-ASA5515-SSP

  SSP ASA IPS 5515-X license

  SF-ASAIPS64 - 7.1 - K9

  ASA software IPS 5500-X 7.1 for IPS SSP

  You can always check through "https://apps.cisco.com/Commerce/home".

  It may be useful

  G1

• IME for version 6.0 of the IPS

  Hi, iam using the module AIP-SSM-10 in ASA 5510.

  my version of the ips is: 6.0 (6) and I want to use ips manager express (IME). I tried with version 6.1.1 and 7.0.2 IME, but both are not supported for the current version of ips.

  1. Please tell me which IME support for ips 6.0 (6) version.

  2. how to level my ips 6.0 version to the current version or higher.

  Please send me url links.

  1. the EMI version 7.0.2 supports IPS version 6.0.6 according file following IME 7.0.2 Readme:

  http://www.Cisco.com/Web/software/282829584/28797/IME-7.0-2.Readme.txt

  Only the new features of the EMI, including monitoring console, dashboard and integrated configuration, health are supported only on the sensors running IPS version 6.1 or later. However, all the other features on IPS 6.0.6 is supported on IME 7.0.2.

  2. you can update the IP addresses directly to version 7.0.2 (E4) using the upgrade package: IPS-K9-7, 0-2 - E4.pkg

  Hope that helps.

• The ASA for FW and IPS options with high availability

  Question 1:

  -----------

  I'm looking for IPS solution for the customer and the verification of the ASA next part number;

  ASA5540-AIP20-K9

  (ASA 5540 appliance w / AIP-SSM-20, SW, HA, 4GE + 1FE, 3DES/AES)

  What does AP mean here - what software?

  In this case you have to buy a second unit (at the same price) for the recovery of?

  (I wondered if ASA has also a cost - efficient as PIX failover solution-discounted price for the unit of failover).

  If I choose the ASA VPN edition is it possible to add IPS inside module?

  Hello

  Q: what does AP means here - what software? In this case you have to buy a second unit (at the same price) for the recovery of?

  The "ASA5540-AIP20-K9" is only for 1 unit of ASA, with function of software HA (active/active, active / standby). You can add/buy another unit to achieve HA/recundancy.

  I think that the price of a unit all them is always the same, ASA has no unit to voluntarily make the function FO.

  Q: if I choose the ASA VPN edition is it possible to add IPS inside module?

  Large malicious Intrusion Prevention & mitigation program is included, as mentioned in the 'picture' 3 Security of the network to the VPN gateway"in:

  http://www.Cisco.com/en/us/products/ps6120/products_data_sheet0900aecd80402e3f.html

  Rgds,

  AK

• IPS 4240 - additional card

  Hello

  Does anyone know, when will be available 4xFE cards for IPS-4240 (for total 8 interfaces)?

  Kind regards

  Krzysztof

  The option card for IPS-4240/4255 sensors will be a card 4GE to support copper (RJ45) and fiber (SX) connections. It will allow a total of 8 RJ45 interfaces or 4 SX fiber interfaces (and 4 RJ45 interfaces) on these platforms. Unfortunately, it will be probably available for another 9 months or more.

• ASA ips feature

  I want to ask you what the works of IPS on ASAs functionality.

  There all the signatures, or it is limited?

  Perfect me if Iam wrong if I say that I needed module AIM for ips work on the asa. If Iam right, so why AIM has only 1 ethernet interface. This means that I am not follow 1 vlan?

  Thank you very much.

  The ASA-SSM-AIP-10 or ASA-SSM-AIP-20 according to the ASA modules is required for full monitoring of IPS features. The IPS on the MSS software is the same as for devices and other modules IPS. It uses the same software and signature updates. (Except for the image of the main system which has a few extra things to allow installation on the SSM)

  Without the ASA-SSM-AIP, the Software ASA itself has a set of very limited signatures that can be monitored. The signatures set is the same as in the previous version of the Pix Firewall.

  As for the single port on the ASA - SSM. This port is not a monitoring port. The port is the port command and control and has an IP address so that you can telnet, ssh or web browse to the sensor, so you can manage. The real follow-up is done on an internal interface connected inside firewall basket. The ASA can be configured through its policy to send packets through the SSM for the analysis of the IPS. Politics on the SAA can be configured for the IPS to monitor packets histocompatibility or inline.

  The SAA can be configured to send all or part of the packets through the firewall to monitor by the IPS of code that runs on the MSS.

  Since the external port is not a monitoring port that DFS may not be configured to control packets that do not go through the ASA. Packets must pass through the ASA ASA copy these packages through internal backplane to the SSM for analysis.

• IPS of ASA journals collection

  Hello

  How can I collect newspapers of the IPS of the ASA? My firewall is ASA 5515 x, 9.1 (5) with module version IPS 4,0000 E4. Please let me know the commands to view the logs of IPS, also, how can I monitor these logs?

  Kind regards

  Martin

  You must use either:

  a. Device Manager IPS (basically ASDM pointed toward the IPS vs ASA address address and used real time connect to the visualization and the configuraiton)

  (b) IPS Manager Express (keeps newspapers even when not active GUI, allows to manage several IPS), or

  cisco Security Manager.

  The first two are free tools for IPS unique or small facilities, and the third is a licensed - the company-wide product.

• Cluster ASA with IPS

  Hello

  I intend to group 4 ASA firewall between 2 domain controllers.

  I would like to know if the ASA IPS device is also grouped with the ASAs 4 or I have to buy the hardware module ASA IPS?

  In the case where I will need to buy the module hardware IPS ASA it will work as a single module or it could also be clustered?

  Thank you very much for the help.

  Kind regards

  J

  The Documentation States that the IPS is managed individually by unit. So every unit will have it of own IPS and protects the traffic he sees. Without a config-replication available for IPS, you should plan to use a system management as MSC company to ensure that all units have the same configuration.