For Windows vista: Startup Repair couln t repair problem

Similar Questions

• Windows Vista startup repair cannot repair this computer automatically

  The issue takes place at the start.  The computer go directly into Startup Repair, which finally returns the message above.  It allows me to report the problem or not and then proceeds to close.  What can I do?

  Problem event name: Startup Repair V2

  Problem 1 of Signatures to 10 below:
  Automatic failover
  6.0.6000.16386.6.0.6000.16386
  6
  1048591
  CorruptFile
  CorruptFile
  322122587
  1
  WrpRepair
  0

  OS version: 6.0.6000.2.0.0.256.1

  Locale ID: 1033

  You can try this:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  How to get Vista recovery Media and/or to use the Vista recovery Partition on your computer.

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  Ask them if you can also make recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their way of doing recovery disk/s.

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1^st in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon.
  Mick Murphy - Microsoft partner

• Error Windows Vista Startup Repair

  My HP PC was working great until yesterday.  My son worked on Microsoft word and trying to launch Mozilla Firefox when the PC froze on him.  He tried to restart but failed to start.  He tried to use the system to repair, but it failed.  Attempts to mulitple system restore function have not as well.  Trying to avoid wiping the hard drive, so I thought I'd post the error here and see if he had any suggestions.  Repairing the system fails with the search for the following bugs:

  Unknown error checking: f4 error checking.  Parameters = 0 x 3, 0x88d1a2e0, 0x88d1a42c, 0 x 82232650
  Unknown error checking: f4 error checking.  Parameters = 0 x 3, 0x88ce4d90, 0x88ce4edc, 0 x 82270650

  The operating system is Windows Vista Home Edition.  I can't get into the PC via the mode without failure or any other means.  The only options seems to be via the command prompt, although I have not yet tried.

  All appreciated the thought...

  ·        Do a startup repair, boot from the disk Installation of Windows Vista genuine (or one that you can borrow from someone) or a recovery disc.  Here is the procedure: http://www.bleepingcomputer.com/tutorials/tutorial148.html.  You may need to change the BIOS to do first the CD drive in the boot sequence to boot from the CD.  To do this, hold the screen that tells you the key F to push to enter the menu start or start of installation.  Push it quickly. Make the changes, save your work and exit.  Put the CD in the drive and reboot.  When you are prompted, press any key to boot from the CD.

  If you do not have a floppy disk, you can make a bootable recovery disk by using http://neosmart.net/blog/2008/windows-vista-recovery-disc-download/ with burning software like: http://www.snapfiles.com/get/active-isoburner.html and, of course, a blank CD.

  If this does not resolve the problem, try the following:

  To run the Bootrec.exe tool, you must start Windows RE. To do this, proceed as follows (some does not apply if you use the recovery disk - but to be honest I don't know if it will work with only a recovery disc):

  1 put the Windows Vista installation disc (or the recovery disk) in the disk drive, and then start the computer.

  2. press a key when you are prompted.

  3. Select a language, a time, a currency, a keyboard or an input method, and then click Next.

  4. click on repair your computer.

  5. click on the operating system that you want to repair, and then click Next.

  6. in the System Recovery Options dialog box, click command prompt.

  7. type Bootrec.exe, and then press ENTER.

  Note If rebuilding the BCD does not resolve the startup problem, you can export and delete the BCD, and then run this option again. In doing so, you ensure that the BCD is completely rebuilt. To do this, type the following commands at the command prompt Windows RE:

  ·        bcdedit/export C:\BCD_Backup

  ·        c:

  ·        Boot CD

  ·        BCD attrib s h - r

  ·        Ren c:\boot\bcd BCD.old

  ·        Bootrec /RebuildBcd

  If this does not work, try to start in safe mode (repeatedly, click the F8 key during the boot and go into safe mode with network - or do it from the command prompt on the drive).  Then we will check some of your system files:

  Go to start / all programs / accessories / command prompt and right click on command prompt, and then click Run as administrator (skip this step if you are using the disk)...

  Type sfc/scannow, go and let it run.  It will scan and try to correct some of your system files.  If all goes well he comes complete with no corruption, it could not repair (if it has these post of corruption here or try to analyze it to find the problem or files using http://support.microsoft.com/kb/928228.

  While in the command prompt, type chkdsk /f /r and enter and let it run.  It will scan and try to solve any corruption or bad sectors on your hard drive and remove especially as a cause.

  If it does not, then thanks for posting any repetitive error message in Event Viewer on startup (Start / Control Panel / administrative tools / Event Viewer - if you use the command line, type eventvwr and enter).  Here's how to use Event Viewer: http://www.bleepingcomputer.com/forums/topic40108.html

  Good luck and I hope this helps!

  Lorien - a - MCSE/MCSA/network + / A +.

• Windows vista Startup Repair will not stop running

  Hi hope someone can help

  When I boot computer it goes to startup repair and custom automatically stops running same thing that happens when I use safe mode. Recently, we used the system restore, it worked fine until we used the Startup Repair
  Thanks for any help you can give

  Hi, Gretaevan2,

  Thank you for visiting the Microsoft Vista answers Forum!

  * If this happens even in safe mode, then it is possible that the hard drive is the source of the problem.

  You can try the following steps:

  STEP 1: Try to perform the disk check and see if there are errors.

  See the following knowledge base to perform the disk check: http://support.microsoft.com/kb/315265

  STEP 2: Try the SFC Scan now.

  See the following knowledge base to run SFC Scannow: http://support.microsoft.com/kb/310747

  If, in case, the step above does not help, try to perform the system restore to an earlier date when everything was working well.

  We can't wait to hear back on your part.

  Best regards, Vishal B. Microsoft Support Engineer answers visit our Microsoft answers feedback Forum and let us know what you think.

• Windows Vista startup repair cannot repair the computer

  event: startuprepairv2
  SIG 01: autofailover
  GIS 02:6.0.6000.16386.6.0.6001.18000
  SIG 03:6
  GIS 04:1114132
  SIG 05: 0x9f
  SIG 06: corruptfile
  GIS 07:3221225624
  GIS 08:3
  SIG 09: wrprepair
  GIS 10: 6.6000.2.0.0.256.1
  locale ID: 1033

  Hello

  Follow the steps in the KB article below and check if this solves the problem.

  Windows Vista or Windows 7 unbootable, and the Startup Repair tool does not resolve the problem
  
  http://support.Microsoft.com/kb/934540

• I need help for Windows Vista black screen during the connection, even with the login screen removed

  Hey, I have a problem in Windows Vista:

  I've been updating / updated my graphics card and it is the graphics card, I'm updating, after a while, a black screen will appear (PITCH BLACK) and I there is no cursor and I tried Ctrl + Alt + Delete, but nothing seems to work, after I turned off my laptop, starts to load then it was the new dark night! (NO LOGIN SCREEN). Then I turned off my laptop then I constantly pressed f8, then I pressed "Computer repair" then it loads then my screen showed "Another user", then I clicked it then I had to type my ID but I have no details of connection, I pressed on enter with no connection details, but this still does not work because I had to type in my login information. I tried everything, then I went to safe mode and fact a password and changed my admin account type, then I rebooted my laptop, then I have constantly pressed f8 and pressed "Computer repair" then it loads and then my screen showed 'Another user' again... .
  
  PLEASE I NEED HELP! I WANT TO PLAY MY GAMES!

  Hello

  Follow the steps below:

   

  Method 1: Do the Startup Repair to fix the problem.

  See the following article for more information on the Startup Repair:

  Startup Repair: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions

   

  Method 2: Use the Bootrec.exe tool in the Windows recovery environment to troubleshoot and repair startup issues in Windows

  For instructions, see the following article:

  How to use the Bootrec.exe tool in the Windows recovery environment to troubleshoot and repair startup issues in Windows

  http://support.Microsoft.com/kb/927392

  Let us know if that helps.

• MS Vista startup repair couldn't fix the problem automatically

  Hello

  A little history - MS Vista was trying to install updates when the delivered system running. He failed. So I rebooted and it worked very well.

  When I re-started again after using it, even once, he tried to install updates. He failed. So I rebooted and it worked fine again. I went through the whole process several times in recent weeks.

  Then the other day, I got this screen start that says "Windows cannot repair this computer automatically. Since then, I can't get the computer started.

  The details of the problem are shown as:
  Problem event name: StartupRepairV2
  Signature of the problem 01: AutoFailover
  Signature of the problem 02: 6.0.6000.16386.6.0.6000.16386
  03:6 problem signature
  Signature of the 04:524296 problem
  Signature of the problem 05: CorruptFile
  Signature of the problem 06: CorruptFile
  Signature of the 07:3221225624 problem
  Signature problem 08:3
  Signature of the problem 09: WrpRepair
  Signature of the 10:10 problem
  OS version: 6.0.6000.2.0.0.256.1
  Locale ID: 1033

  In addition, all tests have been completed successfully, with the same error code = 0x0

  First cause is to the states that "Startup Repair tried several times but still not determine the cause of the problem."

  If I have to re - install the operating system again... I was not given a CDROM as a HP laptop... How can I actually re - install, when I do not have the CDROM?

  Also, I have some very important folders on the hard drive and I want to recover the files first before reinstalling the operating system...

  Any advice on how I can get before I have to destroy it by reinstalling the operating system would be greatly appreciated.

  Thanks to you all.

  As you don't have a Vista DVD, try this:

  Download the ISO on the provided link and do a repair of the disc.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  For recovery disk/s and/or the use of the recovery Partition:

  http://h10025.www1.HP.com/ewfrf/wc/siteHome?lc=en&DLC=en&cc=au

  Online 24/7 support for home and individual HP products

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  You can also make recovery disk/s since the Partition of recovery in case of hard drive failure or System Crash, when you are in service again.

  They will tell you how to do this.

  Every computer manufacturer has their way of doing recovery disk/s.

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  Save all data, because it will be lost during a clean installation.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1 in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon.

  Mick Murphy - Microsoft partner

• I will not let me connect to my main, connect you to where I put my password in and then logs on just continuous vista startup repair in time ever I start my computer

  I will not let me connect to my main, connect you to where I put my password in and then logs on just continuous vista startup repair in time ever I start my computer

  Follow these steps to try to solve your problems of boot.

   

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If the system or Mode restore safe work not and you do not have a Microsoft Vista DVD, make a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• Windows 7 - Startup Repair

  Separated from this thread.

  Well, the computer had problems in the past as not having spent my home screen, but it was not too bad before. After some few downloads, the computer suddenly stopped working or has worked very slowly. Then, I turned it off. I turned on her and I couldn't get past the Windows logo without error message popping up and automatically restart my computer. I tried to run the Startup Repair tool, but there is no that get stuck on a screen. I tried the mode without failure, boot, logging, and the last known good configuration, but the same error message popped up. I even tried the option to restore memory and he has not been able to pick up something wrong. My computer is a Windows 7. Now, you will be able to help me, or is my computer gone for good?

  Hello

  Startup Repair works often from an Installation of Windows 7 or Windows 7 disc
  ERD when it does not value or a recovery disc. If necessary
  How a Windows 7 repair disk is below. An ERD can be made
  on any computer with a CD burner running Windows 7, Vista or XP because it uses
  No files from the host computer.

  You can try some of them in Mode safe - tap F8 repeatedly that you start.

  If you do not have a Windows 7 disc, you can borrow a friends who are not
  protected against copying. The manufacturer of your system will also sell cheap since physical DVD
  you already have windows. You can also do an ERD on another computer.

  Try the Startup Repair - (if at ANY time benefit you from some, but not full access to the Windows)
  Go back and try again to startup repair.)

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  What are the system recovery options in Windows 7?
   http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  Try the disk Options recovery or Windows 7 startup repair.

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  Also from the command PROMPT on the Console (if possible) recovery or a Windows 7 disc

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  Retry After Chkdsk startup repair.

  If after those you try Safe Mode restore or system recovery
  or the Windows 7 disc.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  --------------------------------------------------------------------

  If you need to repair disks - these help repair Windows not re-install.
  Often, these records will help when the OEM recovery disk does not work.

  Download Windows 7 system recovery discs - charge now $9.75 for ISO
  images to make the discs. (It can be done on any computer running XP,
  Vista or Windows 7 which has a CD/DVD burner).
  http://NeoSmart.net/blog/2009/Windows-7-system-repair-discs/

  How create a Windows 7 system - free repair disc (must be made on a
  Windows 7 computer running the same 32-bit or 64-bit).
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  
  An installation disc is possible also to use for repair. Of course you would
  Use your own COST (product key).

  How to: What are my options for Windows 7 reinstall media?
  http://answers.Microsoft.com/en-us/Windows/wiki/Windows_7-system/how-to-what-are-my-options-for-obtaining-Windows-7/528163c1-0b2e-4AD2-a26d-7112851d1dc2

  Welcome to the recovery of Microsoft software
  http://www.Microsoft.com/en-us/software-recovery

  See MVP Andre Da Costa message in this thread.
  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-windows_install/how-can-i-download-gatewaywindows7recovery-disc/3c0ecd74-CFC1-4188-89c7-a6bbe8113ee1

  ======================================

  If necessary:

  What to do if Windows does not start correctly (applies to Windows 7 as well)
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-to-do-if-Windows-wont-start-correctly

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  What are the system recovery options in Windows 7?
  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  A repair Installation allows to keep the programs and data, even if redundant backups are always a good idea.

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  I hope this helps.
  --------------------------------------------------------------------------------------------
  Rob Brown - Microsoft MVP<- profile="" -="" windows="" and="" devices="" for="" it :="" bicycle="" -="" mark="" twain="" said="" it="">

• SP2 for Windows Vista will not install. Receive error 800b0100 code. Windows Update has encountered an unknown error.

  SP2 for Windows Vista will not install. Receive error 800b0100 code. I already tried all possible solutions - disabled and even uninstalled McAfee Firewall disabled, ran the CheckSUR repeatedly (see below for the final analysis), tried to install from windows update, also downloaded the stand-alone MS pack, tried selective startup and hidden States of services, still nothing. It has been 2 days work on this. Help, please!

  =================================
  Preparation of control system was updated.
  Binary version 6.0.6002.22202
  Package Version 6.0
  2009-10-24 12:36

  Checking Windows Service Packages

  Checking of manifests package and catalogs

  Checking package Watchlist

  Watchlist checking

  Checking packages
  (f) MOTHER of CBS missing 0 x 00000002 servicing\packages\Package_2_for_KB975467~31bf3856ad364e35~x86~~6.0.1.0.mum
  (f) MOTHER of CBS missing 0 x 00000002 servicing\packages\Package_for_KB975467_client_1~31bf3856ad364e35~x86~~6.0.1.0.mum
  (f) MOTHER of CBS missing 0 x 00000002 servicing\packages\Package_for_KB975467_client~31bf3856ad364e35~x86~~6.0.1.0.mum
  (f) MOTHER of CBS missing 0 x 00000002 servicing\packages\Package_for_KB975467~31bf3856ad364e35~x86~~6.0.1.0.mum

  Control components store

  Summary:
  Seconds executed: 1241
  Found 4 errors
  CBS MUM lack count: 4

  Unavailable repair files:
  servicing\packages\Package_2_for_KB975467~31bf3856ad364e35~x86~~6.0.1.0.mum
  servicing\packages\Package_for_KB975467_client_1~31bf3856ad364e35~x86~~6.0.1.0.mum
  servicing\packages\Package_for_KB975467_client~31bf3856ad364e35~x86~~6.0.1.0.mum
  servicing\packages\Package_for_KB975467~31bf3856ad364e35~x86~~6.0.1.0.mum
  servicing\packages\Package_2_for_KB975467~31bf3856ad364e35~x86~~6.0.1.0.cat
  servicing\packages\Package_for_KB975467_client_1~31bf3856ad364e35~x86~~6.0.1.0.cat
  servicing\packages\Package_for_KB975467_client~31bf3856ad364e35~x86~~6.0.1.0.cat
  servicing\packages\Package_for_KB975467~31bf3856ad364e35~x86~~6.0.1.0.cat

  Hello Yiratr,

  Thank you for using the Microsoft answers Forums.

  Solution:

  Follow the steps in the web link below.

  http://support.Microsoft.com/kb/956702

  That should do the trick for you.

  Thank you.

  Kind regards

  Augustine.

  "URGO".

  UDAY $012 please let me know that whether the solution worked or not, I thank you and appreciate your comments. URGO

• problems with windows vista startup

  2 days ago, that my computer was running an update. the computer has been accidentally disabled during the upgrade. the next day I got tired of the laptop start but I couldn't access it. When I turn on the laptop it says ""windows is not stopped successfully", then it gives me the opportunity to start in"safe mode","course with the command' or 'normal startup'.» When I click on one of these options, it takes me to the screen where I choose which user to log as long as. After I click on the user, I want to open a session on a black screen appears and it does not change. I see the cursor and I am able to move, but that's all I can do. in 'normal' mode, I try ctrl + alt + delete, but nothing happens (no window opens). in safe mode, I do ctrl + alt + delete and the window but when I click on restart, closed, logoff, or one of the options, nothing happens. I end up having to close the cpu by holding down the power button. I have no cd startup/recovery. I tried the F8 option but nothing happens. Please help me!

  Hello

  In Safe Mode does not allow to do something, try a startup repair and / or a system restore using a DVD of Vista from Microsoft

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  ___________________________________

  There are several methods to reinstall Vista.

  This can help you (download files and make your own DVDs):

  http://www.heidoc.NET/Joomla/technology-science/Microsoft/57-Windows-Vista-direct-download-links

  You can contact your computer manufacturer and ask them to send you a set of recovery disks.

  They should do this for a small fee.

  To reinstall Vista using their recovery disk/s, you start from the 1st recovery disk they provide and follow the manufacturer's instructions to reinstall:

  You need to change the Boot order to make the DVD/CD drive 1st in the boot order:

  How to change the Boot order in BIOS:

  http://pcsupport.about.com/od/fixtheproblem/SS/bootorderchange.htm

  "How to replace Microsoft software or hardware, order service packs and replace product manuals.

  http://support.Microsoft.com/kb/326246

  And if you have never received a recovery disk when you bought your computer, there should be a recovery on the drive Partition hard reinstall Windows how much you bought your computer.

  The recovery process can be started by pressing a particular combination of the key or keys at startup. (Power on / start)

  Maybe it's F10, F11, Alt + F10, etc., depending on the manufacturer.

  Ask them to the proper key sequence.

  Some manufacturers have more available Vista recovery disks.

  If this happens, you may need to try this instead:

  You can also borrow and use a Microsoft Vista DVD, which contains the files for the different editions of Vista (Home Basic, Home Premium, Business and Ultimate) must be installed. The product key on your computer / Laptop box determines what Edition is installed.

  Other manufacturers recovery DVDs are should not be used for this purpose.

  And you need to know the version of 'bit' for Vista, as 32-bit and 64-bit editions come on different DVDs

  Here's how to do a clean install of Vista using a DVD of Vista from Microsoft:

  "How to do a clean install and configure with a full Version of Vista '

  http://www.Vistax64.com/tutorials/117366-clean-install-full-version-Vista.html

  And once the operating system is installed, go to your computer manufacturer's website and get the latest drivers for your particular model or laptop computer.

  And phone Activation may be necessary when you use the above installation method.

  "How to activate Vista normally and by Activation of the phone '

  http://www.Vistax64.com/tutorials/84488-activate-Vista-phone.html

  See you soon

• I have a serial number valid for windows Vista Home Basic, but my hard drive crashed and I have no way to re - install vista on my computer. I am looking for a download so I can do it.

  Basically, I installed windows 2000 on my machine and I can't find a download for windows vista home basic that doesn't have some kind of crack or keygen. I want a legal copy not a hack. I have the serial number supplied with my computer. where can I find this download or get a drive.

  Here are all LEGAL for Vista:

  How to get Vista recovery Media or the Vista recovery Partition on your computer back to factory settings.

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  Ask them if you can also make recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their own way of making recovery disk/s.

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  Save all data, because it will be lost during a clean installation.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://support.Microsoft.com/default.aspx/KB/326246

  'How to replace Microsoft software or hardware, order service packs and upgrades, and replace product manuals'

  See you soon.

  Mick Murphy - Microsoft partner

• Why Microsoft did remove the ability for Windows Vista to install on herself from one location other than being inside the BONE you want to fix it?

  No Option to install repair - SAD

  Hello

  Why Microsoft removed the ability for Windows Vista to install on herself from one location other than being inside the BONE you want to repair.

  I recently had a problem where Vista Business 64-bit would only boot to a black screen with a mobile cursor - KSOD.   Who, in searching the Web I found is a fairly common problem with Vista.  I discovered that my only option was about to reinstall Vista CLEAN and all the other programs I had installed under it.  I can't believe that Microsoft released the 'repair installation option"similar to that of Windows XP, where you can hit the"R"key during installation and we left with nothing but the"System Restore"options and"Startup Repair ".  Neither of which has helped in my situation.  Since then, this was a dual system boot with XP Pro, then any restore point has been removed from the partition to Vista anytime, I started another recognized problem, by Microsoft, which Microsoft has made no significant effort to fix, in addition to recommending that you hide the partion Vista in XP - a whole of XP.  That beats a little the entire purpose of dual boot.

  As I tried to start in safe mode, it left me at the same point as a normal boot - black screen with a cursor.  I tried ctrl + alt + delete and nothing. Two Windows RE options did not help me.  This left me no option but to the completely reinstall Vista.   Why Microsoft did remove the ability for Windows Vista to install on herself from one location other than being inside the BONE you want to repair.. Please don't tell me that it is because Vista uses an image file instead of an installation as XP system.   I see no other reason for not allowing the upgrade of outside BONE in addition to Microsofts greed and paranoia that he can transform the operating system easier to install illegally.  I hope that some third party has actually changed the Vista installation routine to allow you to install Vista on itself, because as it is, it's really hard for me to even recommend Vista as the operating system or install any where else, if not the only recourse after loading OS, is to reinstall completely.

  Adobe, Autodesk, and almost all other software publishers... allow you to perform a "REPAIR" of their software installation, if something prevents you to load after installation.  Even MS Office has a routine repair.  Ms has an internal version of the Setup routine which allows outside the OS upgrade option that you want to "Upgrade" / repair? ".  If not, why?

  -Todd w.

  "Why Microsoft removed the ability for Windows Vista to install on herself from one location other than being inside the BONE you want to repair."

  «.. . After using XP's repair function, the operating system itself would become less stable and frankly not in a good state of repair. »

  As Todd, is the answer.

  "This response does not hold water as on one of my computers I've been running Windows XP for about four years now, after a repair install.

  Then, you were lucky.  Try to replace the system files on a computer that does not start even at a desk or safe mode usually will get a return to office, but will probably repeat the same problem in a few weeks.  Tech professional would only use this function to retrieve the data before a complete reinstallation.

  "I thought that this area was a place to really get answers instead of the ole same"answers of bs that are on all the other forums."

  It is a place that will try to help you fix your computer if you have problems.  It has technicians in computing, no decision-makers, developers or executives.  We will try to answer technical questions about problems you might have with Windows Vista.

  If you want to have input on the future of Microsoft operating systems, then help you beta-test and provide feedback to the developers.  Windows 7 and IE 8 are currently in beta.

  Another possible place you could make suggestions which could see the developers would be:

  https://connect.Microsoft.com/default.aspx

  Brent
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• my wireless does not work when I download the update for Windows Vista (KB2753842) security

  After an automatic download of Windows security update my wireless card did not work. He could not find a wireless networks that she normally

  the fact. When I used a LAN cable I internet connection.
  When I did a system restore to exclude the update of Windows my wireless card security worked perfectly.
  The same thing has just happened and once again had to do a system restore to get a wireless internet network connection. I can only assume that the Windows Security Update for Windows Vista (KB2753842) is the problem.
  Please indicate if this update is critical and if this is the case, what can I do to make sure my wireless card working?
  Thank you.
  Roy

  Thank you very much for your answer.

  I have now solved the problem by using the network connection software to diagnose and repair the problem. My wireless network now works with the update in question.

  Kind regards

  Roy.

  Hi royhorrobin,

  Please report the problem to the Microsoft Community Forum.

  We will help you solve the problem.

   

  1. What is the brand and model of the computer?

  2. do you get an error message?

   

   

  We would like to tell you that this is a critical update...

  Find information here:

  http://support.Microsoft.com/kb/2753842

  Here are some steps that you can follow:

   

  Method 1:

  Step 1: Restore the system to the United Nations-isntall the software update.

  Refer

  What is system restore?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-system-restore

   

  Step 2: Put the computer to boot, with warning...

  From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".
  Follow the steps provide in the article below to perform the clean boot. http://support.Microsoft.com/kb/929135

   

  Step 3: Download and install the update manually to the clean boot.

  Method 2:

  Try to update the Wireless driver and check to see if the same problem happens.

  a. click on start
  b. right click on computer
  c. click Properties
  d. click on Device Manager on the left hand side

  e. in the list of hardware categories, find the device you want to update, and then double-click the device name.
  f. click on the driver tab, click Update driver and then follow the instructions. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  For more information, see:

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly
   

  
  Method 3:
  Also, try the steps from the link below:
  http://Windows.Microsoft.com/en-us/Windows/help/wireless-network-connection-problems-in-Windows
   
  Hope above methods solves the problem. If the problem persists, you can write back to us and we will be happy to help you further.

• After you install service pack 2 for windows vista

  After installing service pack 2 for windows vista on my HP laptop, I started having a few problems. First off the computer would not go beyond the Welcome screen because he showed that an update was the installation (step 1 of 3:0 % etc.) and the computer reboots before finish. It kept the case whenever I started upward, even on safe mode. I tried to restore, but it would never be completed and nothing else would work. Now I can't go beyond the microsoft loading screen because it shows a black flat screen with no cursor. I can't enter safe mode. Help, please. Safe mode only shows the start screen but won't start so I can't access the control panel and tried to boot to the last known successful startup but it failed.

  Hello

  Try a startup repair and / or a system restore using a DVD of Vista from Microsoft

  Manufacturers recovery disks normally do not have Service Options; they are normally a relocation to the factory only settings option.

  Here is the guide to repair Options using a Vista DVD from Microsoft.

  If a friend or a work acquantance of yours has one, you can borrow and use it for repairs.

  http://www.bleepingcomputer.com/tutorials/repair-Windows-with-Windows-Startup-Repair/

  Table of contents

  1. Overview of Windows Vista repair options
  2. How to perform an automatic repair of Windows Vista using Startup Repair
  3. Advanced Tools Overview
  4. Conclusion

  If you do not or can not borrow a Microsoft DVD there is a download of a file ISO of Vista Startup Repair available that you can put on a Bootable floppy to make the above startup repair and that the method is recommended by a large number of posters in these Forums.

  Unfortunately, you have to buy it.

  Here is a link to it:

  http://NeoSmart.net/blog/2011/Windows-Recovery-discs-updated-reinstated/

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  This Information Microsoft can help you resolve problems that you encounter during the installation of Service Packs for Vista.

  http://support.Microsoft.com/kb/947366

  And there is a Forum that Microsoft has put in place for problems with Vista Service Packs. If repost you the Forum they will definitely try to help you here...

  http://social.technet.Microsoft.com/forums/en/itprovistasp/threads

  Or you can repost you this link in the Windows Update Forum.

  http://answers.Microsoft.com/en-us/Windows/Forum/windows_vista-windows_update?page=1&tab=all

  See you soon.