MS Vista startup repair couldn't fix the problem automatically

Similar Questions

• Computer freezing and startup repair does not solve the problem.

  fix my computer when windows start dump then launch startup, but does not solve the problem. Can you help me solve the problem

  Hi Wwiese,

  Thanks for posting your query in Microsoft Community.

  I understand from the description of the problem, the computer freezes in the commissioning on the Windows 7 computer.

  I would appreciate if you can help me with the following information.

  1 were there any hardware or software changes made on the computer before this problem?

  2. are you able to boot into office?

  3. you receive an error message/code?

  I suggest you try these methods and check if it helps.

  Method 1

  Disconnect all external devices (printers, scanner, USB (universal serial bus) drives, etc...) Except the keyboard and mouse and then start.

  If this solves the problem, then add back devices at a time until you discover the piece of hardware causing the issue. Then download drivers software updated for this particular device.

  Method 2

  Try to start in last good known Configuration and see if you can start very well.

  Using the last good known Configuration

  http://Windows.Microsoft.com/is-is/Windows7/using-last-known-good-configuration

  Method 3

  Start the computer in safe mode and check if the problem persists, if the question does not persist then perform the clean boot and check if the problem resolves.

  Step 1

  Safe mode starts Windows with a limited set of files and drivers. Startup programs do not work in safe mode, and only the basic drivers needed to start Windows are installed. Please click the below mentioned link.

  http://Windows.Microsoft.com/en-us/Windows7/start-your-computer-in-safe-mode

  Step 2

  Put the computer in a clean boot state to see if there is a software conflict as the clean boot helps eliminate software conflicts.

  http://support.Microsoft.com/kb/929135

  Note: After completing the steps in the clean boot troubleshooting, follow step 3 from the link to start the computer to a Normal startupmode.

  Method 4

  If the problem persists, I suggest you perform a startup repair and check if it makes a difference.

  Startup Repair: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/Startup-Repair-frequently-asked-questions

  What are the system recovery options in Windows 7?

  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  In addition, you can do a System Restore the Windows Recovery Console.

  It will be useful.

  Let us know if you encounter problems with Windows in the future. We will be happy to help you.

• Vista does not start, go straight to the Startup Repair / can not solve the problem

  5 month old Dell Inspiron 1440, Vista system unbootable, goes directly into the Startup Repair tool, tried F8, tried restoring, tried booting in the safe, he always comes back to the Startup Repair

  Message
  Prob event name StartupRepair V2
  Prob GIS 01 AutoFailover
  Prob GIS 02 6.0.6001.18000.6.0.6001.18000
  Prob GIS 03 0
  Prob 04 65537 GIS
  Prob GIS 05 unknown
  Prob GIS 06 NoOsinstalled
  Prob GIS 07 0
  Prob 08 1 GIS
  Prob GIS 09 FixPartitionTable
  Prob 10 1168 GIS
  OS version: 6.0.6001.2.1.0.256.1
  1003 locale ID

  Since this system is under warranty, call Dell, they tell me that it is a hard drive failure.  Is there anything I can try to fix?

  Thanks in advance

  Your Dell is 5 months old.

  It is under warranty.

  Dell will fix it.

  Do what Dell suggest regarding your warranty.
  Everything you do can void your warranty.

  http://support.Dell.com/

  Link above is Dell Suport.

  http://en.community.Dell.com/

  Communities of Dell at the link above.

  Here are the ways to back up your data:

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1^st in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon. Mick Murphy - Microsoft partner

• BSOD: "a process or thread crucial to system operation has unexpectedly released or ended." Startup Repair does not solve the problem-

  I recently had a serious viral infection on my laptop Windows Vista SP2 Gateway.  After you run the antivirus AVG cleaner, who seemed to have had to quarantine or delete some files infected, System I couldn't Boot Windows to the top on this machine - even in the (all flavors of) Safe Mode.  When you try to start, I'd get

  a Blue Screen of Death with the msg of error in the title of this thread.  Before turning off the crash dump, the system indicated:

  ' * STOP: 0X000000F4 (0 X 00000003 0X85F22848 0X85F22694 0X82A26AB0).

  Other messages in the BSOD said I might have new HW causing the BSOD (I did not - but nevertheless I removed all external HW and tried again - got the same result).

  So one of the first things I did was to capture the startup log, so I could see what the pilots were hang up / does not.  Here's what I found:

  (1) the last driver to load (as indicated in ntbtlog.txt) was monitor.sys.  My understanding is that this indicates that when this driver loaded, the system crashed at this place - suggesting that there is 'something wrong' with this particular driver.  However, it seems likely, that I can use the screen/monitor (built-in) to the laptop without problem.

  (2) several drivers do NOT load: they are:

  1 NDProxy.sys

  2 Kvhfjgcv.sys

  3 Kbdhid.sys

  4 i8042prt.sys

  QUESTION 1: "Monitor.sys" being the last driver to load, should I assume this is the driver the system hung up on (that is, which caused the BSOD)?  And if so, that means I should replace this driver?  If so, how do I do that (how and where can I get a copy of 'Clean/good' of monitor.sys)?

  QUESTION 2: Is it possible to get "good versions" of drivers I listed above which was NOT loaded (I guess they didn't not load because they have been corrupted by the virus or the virus cleaner, or maybe just deleted by the virus cleaner because they were infected) to put into the Windows\System32\Drivers folder?  How?

  Here are the steps I took to try to fix the "corrupt system".  I inserted my Windows Vista DVD into the DVD drive and loaded Windows using that.

  Once that came, I then tried the following (and here are the results for all that I tried):

  (1) I selected the option "Repair", then choose "Microsoft Windows Vista" OS and press "next".  He tried to 'attempt to repair' for 15 minutes about, then finally stopped with a message: "Startup Repair cannot repair this computer automatically.  "Details of problem indicated: (a) the problem event name: StartupRepairV2." Signature 01: ExternalMedia; Signature 02: 6.0.6000.16386.6.0.6001.18000; Signed 03:6; Signature 04:131074. Signature 05: 0xF4; Signature 06: 0xF4; Signature 07:0; Signature 08:2; Signature 09: WrpRepair; Signature 10:5; OS version: 6.0.60090.2.0.0.256.1

  (2) I selected the option 'display diagnostic and repair details '.  He said that all tests successful (error code = 0 x 0), and

  then indicated the 'cause': ' unknown error checking: bugcheck f4, parameters = 0x3, 0x88607b80, 0x88607ccc, 0x82a78ab0. "

  - AND -

  Repair action: repair and checking the integrity of system files.  Result: failed.  Error code = 0 x 5

  (3) I checked that the restoration of the system, and even though I know I had some Restore Points created at the origin of this system, System Restore has indicated that there was no restore points to go back, (leading me to believe that the virus must have killed)

  (4) so I chose the selection "Command Prompt", which opens by default "X:\Sources >".  I'm in C: and then typed: "sfc/scannow".  The system has responded with the following messages:

  "Start system analysis.  This process will take time. " follow up 30 seconds later by the message:

  "Windows resource protection could not perform the requested operation".

  MAIN QUESTION: any reflection on what other tools and options I try to repair the windows installation / driver set?

  Hello

  I suggest you follow the steps below:

  Method 1:

  Follow the steps in the link and check if the problem persists:

  http://support.Microsoft.com/kb/958233

  Method 2:

  Connect over winre and rename the driver files that he talked with *.old quick order. You can find these % system32%. Follow these steps:

  a. use the Windows 7 DVD to start the computer from Windows Recovery (WinRE).

  b. in WinRE, open a command prompt. To do this, follow these steps:

  On the screen to install Windows, select the appropriate language to install, time and

  currency format and keyboard or input method options and then click Next.

  c. click on repair your computer.

  d. click 7 installation you want to repair, and then click Next.

  e. click on command prompt.

  f. navigate to % system32% and rename old files 8.

  Method 3:

  After step above the computer restarts. Run the System File Checker tool to troubleshoot missing or corrupted system files. Follow the steps from the link:

  http://support.Microsoft.com/kb/929833

• Vista won't start and the startup repair can't find any problems

  Have a Dell Inspiron under Vista 64 bit, which does not start. I have inserted the re installation DVD and ran the Startup Repair which could not detect a problem.

  Diagnosis and repair are the following

  ----------------------

  Managed last start: 2010-10-23 21:12:44 (GMT)

  Number of repair attempts: 1

  Details of the session

  -------------------------------

  System disk = \Device\Harddisk0

  Windows directory = C:\Windows

  AutoChk run = 0

  Number of root causes = 1

  Test performed

  ------------------------------

  Name: Search for updates

  Result: Completed successfully. Error code = 0 x 0

  Take time = 0ms

  The test is performed:

  ------------------------------------

  Test the disc name: System

  Result: Completed successfully. Error code = 0 x 0

  Taking time = 0ms

  Name: Troubleshooting disk

  Result: Completed successfully. Error code = 0 x 0

  Time taken = 218ms

  The test is performed:

  ------------------------------------

  Name: Metadata for the drive Test

  Result: Completed successfully. Error code = 0 x 0

  Time taken = 62ms

  The test is performed:

  ------------------------------------

  Names OS test target

  Result:

  Completed successfully. Error code = 0 x 0

  Taking time = 188ms

  The test is performed:

  ------------------------------------

  Name: Checking content Volume

  Result: Completed successfully. Error code = 0 x 0

  Time taken = 140ms

  The test is performed:

  ------------------------------------

  Name: Diagnostic Boot manager

  Result: Completed successfully. Error code = 0 x 0

  Taking time = 78ms

  The test is performed:

  ------------------------------------

  Name: Diagnostic log for the system startup

  Result: Completed successfully. Error code = 0 x 0

  Taking time = 16ms

  The test is performed:

  ------------------------------------

  Name: event log diagnosis

  Result: Completed successfully. Error code = 0 x 0

  Time taken = 530ms

  The test is performed:

  ------------------------------------

  Rated: Internal audit of State

  Result: Completed successfully. Error code = 0 x 0

  Taking time = 0ms

  The test is performed:

  ------------------------------------

  Name: Start-up condition Test

  Result: Completed successfully. Error code = 0 x 0

  Taking time = 0ms

  Root cause found:

  -----------------------------

  State of the start indicates that the OS booted successfully

  But the laptop still wont start I tried to run chkdsk/r from the command line and was unable to do as he says Windows cannot run disk checking on this volume, because it is write protected. I don't know what to do now anyone no matter what ideas thanks in advance.

  Seems odd. Startup Repair should have solved the problem.

  Have you tried new reboot running?

  Give it a shot...

  Any chance that you have a "backup computer?

  Try to do a full restore of the PC.

  See how it goes...

  Man is the only animal that laughs and cries; because it is the only animal that is struck by the difference between what things are and what they should be.

• Vista will not solve, goes directly to the start of the repair/cannot fix the problem.

  It says wwindows faid load because the system registry file missisig or corrupted.lve tried everything, and he always comes back to the same tried message.even now the key f8 during the restart and no matter that l can't just back.can help you please and thankyou.also says status: 0xc000014c if this helps

  Hello
   
  1. don't you make changes before the show?
  2. who is the manufacturer of the system?
   
  We checked for error "status: 0xc000014c ' and the troubleshooting step for this problem is to perform the Startup Repair by using the Vista DVD. To do this, follow the steps mentioned below:
  1. Insert the installation disc into the CD/DVD ROM.
  2. restart your computer.
  3. If you are prompted, press any key to start Windows from the installation disc.
  Note: If your computer is not configured to start from a CD or a DVD, see the documentation provided with your computer. You may need to change your computer's BIOS settings. For more information, see BIOS: frequently asked questions.
  4. choose your language settings, and then click Next.
  5. click on repair your computer.
  6. Select the operating system you want to repair, and then click Next.
  7. in the System Recovery Options menu, click Startup Repair. Startup Repair can invite you to make choices as it tries to solve the problem, and if necessary, it may restart your computer, because it makes the repairs.
  8. once the Startup Repair tool is completed, remove the Vista DVD from the CD/DVD ROM and restart the computer as usual.
   
  For more information about the Startup Repair, see this link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/startup-repair-frequently-asked-questions
   
  IMPORTANT: If the startup repair does not resolve the problem, you can choose "System Restore" Windows recovery environment and check the result.
   
  If you do not have the Vista DVD, and then contact the manufacturer of the system for more support options.
   
  I hope this helps.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Windows Vista update will not install and causes cell phone restart. Laptop will not reboot and Startup Repair cannot fix the problem.

  Windows Update tried to install 4 days now. Every time he tries it tells me it failed and trying to install in manually. He said then the laptop restarts, but it does not start. Startup Repair tells me that it cannot solve the problems.
  I don't know how to go beyond this problem, can someone help me? I have no disk Vista as it came pre-installed on my laptop. Help, please!

  If your Vista is preinstalled, ANY support for your laptop is the manufacturer of the computer, not Microsoft.

  Try this:

  Restore point:

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If restore work not and you do not have a Vista DVD from Microsoft, do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  How to get Vista recovery Media or the Vista recovery Partition on your computer back to factory settings.

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not she, transfer your question in the appropriate Forum:

  Windows Update Forum:

  You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.

  In this way, you will receive the best help.

  See you soon.

  Mick Murphy - Microsoft partner

• For Windows vista: Startup Repair couln t repair problem

  I am trying to repair a laptop from a friend, but I'm new to this kind of thing and it's a problem starting. I don't think I have a hardware problem because I have the video but I can't load the operating system and I ranstartup repair, but he could not fix the problem. I received this message:

  Startup Repair cannot repair this computer automatically

  Signature of the problem:
  Problem event name: StartupRepairV2
  Signature of the problem 01: Auto failover
  "' 02: 6.0.6000.16386.6.0.6001.18000
  ""03: 6.
  ««04: 262148»»
  «' 05: Badpatch»»
  "" 06: Badpatch.
  ""07: 0"
  "" 08: 3
  «' 09: WrpRepair»»
  ""10: 0.

  The problem started when my friend has installed updates, unfortunately I do not know what they are, and she said that she did not bring any modification other than recently. If you need more info I can try to help, but I'm kinda at a loss of what to do something without possible srewing up.

  What is the startup problem?  Are there any error messages, and if so what is the EXACT text (including all codes)?  Which version of Vista is?

  Do you know when this problem started?  Try a system restore to a point in time BEFORE the problem started.  Here is the procedure: http://www.howtogeek.com/howto/windows-vista/using-windows-vista-system-restore/.  Don't forget to check the box to show more than 5 days of restore points.  If the first attempt fails, then try an earlier point or two.  NOTE: You will need to re - install any software and updates that you have installed between now and the restore point, but you can use Windows Update for updates.

  If this does not work, try to start in safe mode (repeatedly hit F8 key so that the start and go in safe mode with networking).  Then we will check some of your system files:

  Go to start / all programs / accessories / command prompt and right click on command prompt, and then click Run as administrator.

  Type sfc/scannow, go and let it run.  It will scan and try to correct some of your system files.  If all goes well he comes complete with no corruption, it could not repair (if it has these post of corruption here or try to analyze it to find the problem or files using http://support.microsoft.com/kb/928228.

  While in the command prompt, type chkdsk /f /r and enter and let it run.  It will scan and try to solve any corruption or bad sectors on your hard drive and remove especially as a cause.

  If it does not, then thanks for posting any repetitive error message in Event Viewer on startup (Start / Control Panel / administrative tools / Event Viewer).  Here's how to use Event Viewer: http://www.bleepingcomputer.com/forums/topic40108.html.

  If this does not work, you will need to do a repair/system upgrade using the Windows Vista Installation disc authentic (you own or that you can borrow from someone).  Here is the procedure: http://www.vistax64.com/tutorials/88236-repair-install-vista.html.  Although this will not affect your data, settings or programs, you should always back up your data before you start just be on the safe side. If other procedures do not work, it is almost certain to work.  You can have a lot of updates to re - install (including all you need to remove service packs).  If the version on system with SP1 or SP2 preinstalled cane and the disc is an earlier version, then you will need to do a slipstream drive as follows: http://www.vistax64.com/tutorials/151606-vista-sp1-slipstream-installation-dvd.html.

  I hope one of these procedures can solve your problem.  If this isn't the case, after return and we will try something else.  Return message anyway so we know how it turns out.

  Good luck!

  Lorien - a - MCSE/MCSA/network + / A +.

• Auto repair couldn't fix your PC

  I tried all the options in the menu options start and can't get Windows 8 to start. I just get "auto repair couldn't fix your PC." And later: "log file: D:\Windows\System32\Logfiles\Srt\SrtTrail.txt ' with the closure and the button advanced options, which takes me just on-screen startup options.

  I have no installation media because it is originally a machine win7 for which I downloaded Windows 8.

  I actually found a recovery disk, I had made 3.5 years ago and was able to use it. I also have a backup more recently I could use to recover most of the files.

• I will not let me connect to my main, connect you to where I put my password in and then logs on just continuous vista startup repair in time ever I start my computer

  I will not let me connect to my main, connect you to where I put my password in and then logs on just continuous vista startup repair in time ever I start my computer

  Follow these steps to try to solve your problems of boot.

   

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If the system or Mode restore safe work not and you do not have a Microsoft Vista DVD, make a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• Windows Vista startup repair cannot repair this computer automatically

  The issue takes place at the start.  The computer go directly into Startup Repair, which finally returns the message above.  It allows me to report the problem or not and then proceeds to close.  What can I do?

  Problem event name: Startup Repair V2

  Problem 1 of Signatures to 10 below:
  Automatic failover
  6.0.6000.16386.6.0.6000.16386
  6
  1048591
  CorruptFile
  CorruptFile
  322122587
  1
  WrpRepair
  0

  OS version: 6.0.6000.2.0.0.256.1

  Locale ID: 1033

  You can try this:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use it.

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner: http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  How to get Vista recovery Media and/or to use the Vista recovery Partition on your computer.

  There is no Vista free download legal available.

  Contact your computer manufacturer and ask them to send a recovery disk/s Vista set.

  Normally, they do this for a cost of $ small.

  In addition, ask them if you have a recovery Partition on your computer/laptop to restore it to factory settings.

  See if a manual provided with the computer or go to the manufacturer's website, email or you can call for information on how to make a recovery.

  Normally, you have to press F10 or F11 at startup to start the recovery process...

  Another way I've seen on some models is press F8 and go to a list of startup options, and launch a recovery of standards of plant with it, by selecting the repair option.

  Ask them if you can also make recovery disk/s for the recovery Partition in case of a system Crash or hard drive failure.

  They will tell you how to do this.

  Every computer manufacturer has their way of doing recovery disk/s.

  Or borrow a good Microsoft Vista DVD (not Dell, HP, etc).
  A good Vista DVD contains all versions of Vista.
  The product key determines which version of Vista is installed.

  There are 2 disks of Vista: one for 32-bit operating system, and one for 64-bit operating system.

  If install a cleaning is required with a good DVD of Vista (not HP, Dell recovery disks):

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  http://support.Microsoft.com/default.aspx/KB/918884

  MS advice on the conduct of clean install.

  http://www.theeldergeekvista.com/vista_clean_installation.htm

  A tutorial on the use of a clean install

  http://www.winsupersite.com/showcase/winvista_install_03.asp

  Super Guide Windows Vista Installation

  After installation > go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > get latest Vista drivers for it > download/install them.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Data recovery:

  1. slave of your hard drive in another computer and read/save your data out there.

  2. put your Hard drive in a USB hard drive case, plug it into another computer and read/save from there.

  3 Alternatively, use Knoppix Live CD to recover data:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1^st in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

  See you soon.
  Mick Murphy - Microsoft partner

• I get this error at startup: this application has failed to start because uncdms.dll was not found. Reinstalling the application may fix the problem

  I recently did a full recovery on my pc.  I'm running on Windows XP Pro.  Since the resumption, I get this error at startup: this application has failed to start because uncdms.dll was not found.  Reinstalling the application may fix the problem.  I don't find Windows Search in my Add/Remove programs.  How can I uninstall it?

  Hello
  The uncdms.dll file is associated with the Application of desktop search in Windows that is used to find and view an overview of the different types of files, such as documents, e-mail, photos and music files on a computer.

  Methods of resolution:
   
  I suggest you to download windows desktop search for additional and install.

   
  http://support.Microsoft.com/kb/940157

• I lost all the sound elements of the vista Media Center! How can I fix the problem?

  I have vista Home premium op sys and my media center windows lost audio output. Wheather read files from my hard drive or a DVD. mEDIA PLAYER has SOUND BUT NOT MEDIA CENTER. How can I fix the problem?

  Hello
  • What were the changes made before the problem occurred?
   
  You can check this link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-audio-problems-in-Windows-Media-Center

• ATI driver uninstalled and obtaining a black page says he needs the windows disc to fix the problem.

  Original title: Windows Vista Home Premium with upgrade

  I tried to update my ATI driver, and it got uninstalled. Now windows will not open. Black page says he needs the windows disc to fix the problem. The drive came with my computer. Download driver somewhere?                                                                                                                                                                         I am running windows Vista Home Premium with upgrade.

  Thanks Gene

  Hello Gene,

  You can try to perform a startup repair and see if it helps. You can check if your system has the integrated system recovery option to perform the Startup Repair. You can check in the advanced boot option to see if you have an option to fix the computer to perform the Startup Repair.

  You can read the following article to get started in the advanced boot options.

  Startup options (including safe mode)

  If this isn't the case, you have a Vista installation disk to perform the same.

  For more information, you can consult the following articles:

  What are the system recovery options in Windows Vista?

  Startup Repair: frequently asked questions

  Hope this information is useful.

• Error: "C:\Program Files/reviversoft\Registry Reviver\unins000.msg"is missing." "Fix the problem or get a new copy of the program.

  Original title: cannot start computer

  Cannot start computer

  This response comes and does not let me start the computer (Message missing file 'C:\Program Files/reviversoft\Registry Reviver\unins000.msg "is. Fix the problem or get a new copy of the program) what should I do to get the computer?

  Hi Dan Maarsman,.
   
  -Did you change on your computer before this problem?
  -Do you have any third party registry cleaner program installed on your computer?
   

  Start your computer Safe Mode and check if you can successfully start.

  Safe mode starts Windows with a limited set of files and drivers. Startup programs do not work in safe mode, and only the basic drivers needed to start Windows are installed.

  For more information, see:

  A description of the options to start in Windows XP Mode