FPGA 2012 training: exercise fails '4-Wire Protocol' 7-2: not supported in single-cycle Timed loop

Similar Questions

• Acquisition of data using the single cycle timed loop in labview fpga (7833R target)

  Hi all

  I want to acquire data of input analog of a generator using the loop of the timed cycle and DMA FIFO funtion. I want to use the acquired data to act as a process for my PID control variable. Can the attached code perform the goal? I'm skeptical about its features. Advice or suggestions please.

  Kind regards

  Opuk

  The SCTL does nothing for you here.  Just remove it and write directly from your analog read the DMA write.

  And on the side of the host, you must move the Run method for before the loop.

  You should also consider to the PID in the FPGA.  PIDs work best in a deterministic environment, and you get more deterministic than on an FPGA.

• FPGA: Vs timed loop Timer?

  Hello

  I would like to create a FPGA loop that runs at a fixed rate. Whatever if I use a timed loop structure or a timer loop express VI into a regular while loop? Under what circumstances should I choose one over the other?

  I understand that the timer loop approach can cause the code in the loop run twice before calendar is established (but this isn't a problem for me here). Are there other differences in the two approaches?

  Thanks in advance.

  JKSH wrote:

  But my question was about the differences between the use of "multi-cycle" Timed loops and VI express loop timer.

  In a targeted FPGA VI, all call loops are single cycle timed loops (SCTL).  This means that all the code in a SCTL must run in a clock cycle, so there are a few types of nodes cannot be used in such a loop.  In a used while loop with a timer, you can use a wider range of features, but the loop will generally run much more slowly.

  These documents may be useful to learn how to use loops clocked on FPGA:

  Using loops of Cycle time unique to optimize the FPGA VIs

  Optimization of your screws of LabVIEW FPGA: running in parallel and Pipelining

• Failed installing Photoshop Elements: Installer does not install on a 64-bit operating system

  Bought 13 elements Photoshop from Adobe by Amazon for download.  He said one of the requirements is a 64-bit operating system. Very well. Downloaded correctly. I have a Dell Inspiron 15 with 64-bit processor. Initialized Adobe install, put n serial, you tap on install.  Failed installation: error msg - installer does not support installation on a 64-bit system. Please download the 64-bit version of Photoshop Elements. Help.

  Download the 64-bit Installer

  Downloads available:

  • Suites and programs: CC 2014 | CC | CS6 | CS5.5 | CS5 | CS4 | CS3
  • Acrobat: XI, X | 9,8 | 9 standard
  • First Elements: 13 | 12 | 11, 10 | 9, 8, 7 win | 8 mac | 7 mac
  • Photoshop Elements: 13 | 12 | 11, 10 | 9,8,7 win | 8 mac | 7 mac
  • Lightroom: 5.6| 5 | 4 | 3
  • Captivate: 8 | 7 | 6 | 5
  • Contribute: CS5 | CS4, CS3

  Download and installation help links Adobe

  Help download and installation to Prodesigntools links can be found on the most linked pages.  They are essential; especially steps 1, 2 and 3.  If you click on a link that does not have these listed steps, open a second window by using the link to Lightroom 3 to see these "important Instructions".

• Windows Server 2012 with EFI fails to start after reset of HA

  The purpose of this thread:
  1. a solution, if anyone else has this problem.
  2. If someone has a better knowledge of why this happens or how avoid feel free to explain it please.

  The scenario:

  I was a new analysis a HBA via the Web Client (something I've done many times before in the non-Web client without any problem...) and loses connectivity to the ESXi host. No response from the ESXi at all and I've noticed a GROUP... That's fine for now...

  The biggest problem is that the VM on the failed host installs via HA to my other ESXi in the cluster, each of them has started normally except my 2012 server s. Just the Automatic Startup Repair Wizard has started, and I couldn't do much from there... I tried a few things auto repair, but they could not fill...

  So, I entered the command line tools and ran from diskpart. Discs not presented at all. That's where he hit that I use PVSCSI drivers for my 2012 s server so I was trying to understand how I could inject the command line, but I tried something else first...
  I started the virtual machine on the ISO 2012 server. Tried the option repair, no OS not found to fix, so I chose a new installation and loaded drivers PVSCSI pvscsi-floppy, interrupted the installation and tried the repair option again. He said something like "Continue to start Windows Server 2012" and viola! The VM rebooted successfully and started successfully in the operating system.

  All 3 2012 Server virtual machines on failure that esxi is affected. No Server 2008 or linux where affected machines but they do not use the pilot PVSCSI.

  
  Anyone has a solution alter or maybe an explanation why this happened? This will happen if HA into action on my server 2012 s?

  Is it possible to test or confirm without killing an ESXi host?

  I am running vSphere 5.5 and I don't think that I had this problem with 5.0 or 5.1, but I'm not 100% sure that cause I don't remember no matter which GROUP or another that are running older versions of the failure.

  Hardware version is 9, EFI boot.

  Thank you!

  Finally, I solved this... Looks like a mistake to the EFI initialization after reset of a HA. I know EFI is not supported by FT but I'm only using HA I can't find anywhere that it says that it should not work.

  This is how I fixed the corrupt WS2012 boots:

  1 boot WS2012 ISO, select new installation, load drivers PVSCSI, interrupt installation and choose repair. (Only needed if PVSCI-pilot helps you bootdisk)
  2. choose Help and then command Promt
  3. Run diskpart
  flight type list
  Locate the number of the partition-small FAT32 EFI, in my case nr 3
  Salt type flight 3

  type assign

  flight type list

  Choose the letter assigned, in my case E:
  Type exit

  4 cd /d e:\efi\microsoft\boot

  5 ren BCD BCD.bak

  6 bcdboot c:\windows/l en-us/s E: /f ALL

  7 bootrec /fixmbr

  Bootrec /fixboot

  Bootrec /scanos

  Bootrec /rebuildbcd

  Don't know if all these are necessary... However, it works. Note that the scanos and rebuildbcd show 0 found BONES.

  8 exit the command prompt and click on "Continue starting the server 2012" after that recharge should work properly again.

• wire protocol driver

  Hi guru am new on hyperion looking for help on hyperon, what do you mean by pilot wire protocol pls tell me in brief

  Cameron, have a link? I don't have google... ;-)

• Application of air using URLLoader w/HTTPS fails on some Win7 computers, but not others

  We have an Air (SDK 4.5) application, we are ready to deploy, but fails to connect via the HTTPS URL with error #2032 on some Win7 computers, but not others.

  For troubleshooting, I can reproduce the problem by using the example of app simple test given in the AS3 URLLoader documentaton.

  The problem is that when you run the application on some Win7 boxes, trying to connect to various servers via https and download a simple document, the request fails with "Error #2032".

  The version of the Air runtime is 3.0, and we have updated to 3.1 with the same result. The problem is related to the HTTPS only: the same URLS work fine with HTTP.

  Now for the fun: an application exact air works fine on another Win7 box, of the area of XP, OSX 10.6 and 10.7, pointing to the same URL HTTPS OSX.

  More fun: on Win7 boxes that in case of failure, it only fails with some https URL and not others, and URLS that fail with this Air app on these some win7 boxes work perfectly with the same air application on several others mentioned computers (XP, OSX and other win7).

  I know that #2032 Error is a very generic error "io" and could be the result of many things, but in this case, I did some research to isolate what could happen;

  on win7 boxes where the air application fails:

  If we point the air application on a virtual host on our setup of server apache with a self signed SSL certificate, the air application appears a sign saying the cert isn't trused, and if we click on 'continue', we get the error 2032 and a 0 http status code. Apache never logs on demand. This tells me that the application of air attempts to negotiate an SSL session with the apache server, but never succeeds.

  If we indicate the air even application a virtual host on the same configuration of Apache Web server with a REAL SSL cert, the air application never appears unreliable Panel, but still does not work, 2032 and the http status code returned 0.

  If we indicate the air even application a virtual host on the same server apache but HTTP instead of HTTPS, there is no failure and demand ends with an http 200 status code.

  Interestingly, if we note the same air application various other HTTPS URLS on different hosts, our servers and others on the internet that we know work, some fail the same way and some work very well.

  Now: If we run the same tests with the same air app, using the same URL HTTPS on other computers mentioned (XP, OSx and other win7), there is no failure and demand always ends well.

  Another finding: you could theorize that there is something wrong with those boxes of win7, but the HTTPS URLS that fail with the air app, nice job on these boxes in IE and Chrome, also the same test app compiled as a Flex application and executed in the browser on computers that fail to work fine with the same HTTPS URLS that fails and the application of air , for the air runtime of problems on some win7 boxes.

  It is a BIG problem for us, our Air application is a consumer application and will be widely deployed, and we cannot have it not be performed only on some computers and have no idea why.

  Any help would be apprechiated.

  Thank you

  Bob Reynolds

  Software engineer

  EDT

  PROBLEM SOLVED (mostly), however I end up with big problems in this...

  The problem was on the failure both Win7 boxes were sigficantly off the coast. Their synchronization solved the problem. I assume that others who have similar problems check the time on the computers/servers.

  This raises the question of why the AIR runtime cannot negotiate an SSL connection under this condition, but each browser we tested on those same computers could?

  I can buy that maybe the SSL protocol must by definition fail under these conditions, however for use by consumers, where it can not be controlled, the implementation must be loose to allow upward, and indeed all commercial browsers can negotiate SSL under these conditions connections (time synchronization offset) - ecommerce would be in trouble if consumers can probably not to connect to a service secured via Internet simply because the time is out of their computer.

  Can anyone in the Group Air address Adobe this concern on the use of AIR for applications of consumer under this condition where you can't rely on your application to install or run on who knows how many computers to consumers?  And to make things worse, AIR doesent provide revised, detailed error information so it is VERY tedious or impossible to even troubleshoot a comply with instructions like that--on the ground, it would be rather impossible.

  Thank you

  Bob Reynolds

• How I can corect the following protocols (rtsp) is not associated with any program or is not allowed in this context

  The address was not included

  Firefox doesn't know how to open this address, because one of the following protocols (rtsp) is not associated with any program or is not allowed in this context.

     You might need to install other software to open this address.
  

  I'm not a Curmudgeon, so please keep it simple.

  Thank you

  Firefox 32.0.3 has this security update.
  You can check the version in "> about".

• I try to get Firefox to open Vuze when I click on a magnet link, I get the following message: Firefox doesn't know how to open this address, because the Protocol (loving) is not associated with any program. tell me the solution

  When I try to open a torrent using magnet, I get the following message. Firefox doesn't know how to open this address because the Protocol (loving) is not binding to any program.

  I had this problem and just reinstalled Firefox. Problem solved. In my case, I believe that it is through the installation of FlashGet. Although I uninstalled FlashGet, it had outstripped the Magnet links / Protocol. I hope this helps you with your instance. Fortunately, I had Setup for my version of Firefox (7.0.1) registered and used that but you might need to search for your current version or install a later version

• I try to connect my apple TV.  I've been up to signature in ITunes but got the message that the connection failed because the network time has not been set.  I don't know what I should do.  Thanks in advance.

  I try to connect my apple TV.  I've been up to signature in ITunes but got the message that the connection failed because the network time has not been set.  I don't know what I should do.  Thanks in advance.

  Date and me are dealt with by the network. Try restarting your router/modem...

  Verify that DNS is set to auto

  Make sure port 123 is open on the router (refer to the manual of the router to you)

• Problem of the intranet: "Firefox doesn't know how to open this address, because the Protocol (k) is not associated with any program."

  Creation of an intranet to a collection of security videos and am linking to a video through a picture icon in the form of:
  < a href = "K: \'link to the movie" > ""
  < /a >

  Overview on the works of IE9, the movie starts when the splash screen is clicked, but in Firefox, I get the alert "Firefox doesn't know how to open this address, because the Protocol (k) is not associated with any program."

  InterLan VLC is the video player by default on the PC. I don't want to put video controls anywhere in the page.

  I code for XHTML 1.1 strict with CSS 2.1, and Firefox 5 handles all of my eccentric styles while IE9 has a few issues, while Firefox is my browser of choice.

  Looking at my Options in Firefox, 'File Windows Media audio/video' is configured to use VLC.exe, so I'm always looking to solve this problem.

  Any Suggestions?

  You must use the Protocol file:// (file:///k:/link_to_movie).
  Easier to see the links to use are to open a file via file > open a file

  • http://KB.mozillazine.org/Links_to_local_pages_do_not_work

• [Solved] Message "Firefox can't open this address, because the Protocol (icyx) is not associated with any program. icyx://stream-16.streamsolutions.co.UK:9102

  Hello
  Firefox doesn't know how to open this address because the Protocol
  (icyx) is not associated with any program.
  This happens when I open a radio station - lmradio.net / and then try to
  play with my Windows media player. All of a sudden, it happened that I had no problem before yesterday.
  My OS is Windows 7 Pro.
  Concerning
  David Rennie

  You install the Orban/Coding Technologies AAC/HE-AAC Player plugin.

  This solves the problem.

• I have updated and now when I try to log on to Web sites with fingerprint reader, I get "Firefox doesn't know how to open this address, because the Protocol (dpql) is not associated with any program."

  I have updated and now when I try to log on to Web sites with fingerprint reader, I get "Firefox doesn't know how to open this address, because the Protocol (dpql) is not associated with any program."

  What is the Digital Persona fingerprint scanner? If it's that they have abandoned, for more details, see https://support.mozilla.com/en-US/questions/799388

• Impossible to download music - error message reads "Firefox doesn't know how to open this address, because the Protocol (wmms) is not associated with any program."

  I bought a song to download from Wal - Mart.com and received the error message when I tried to download the song. "Firefox doesn't know how to open this address, because the Protocol (wmms) is not associated with any program." I've never had a problem before. I paid for this download & even I can't access it.

  The site of Wal-Mart offer a plugin or program (Walmart MP3 music downloads) to manage this Protocol?

  See:

  • http://MP3.Walmart.com/store/help/help.htm
  • http://MP3.Walmart.com/store/help/downloading.htm

  On a protocol must be enrolled in a program for Windows that supports this Protocol.

  See also http://kb.mozillazine.org/Register_protocol

• the boot selection failed because a required device is not accessible

  Hello

  I give my 15 years old nephew an old laptop so I am trying to run a system recovery and restore it to its original state factory.

  As soon as I clicked on Recovery Manager > System Recovery > restore to their original factory condition, I get a screen with this message Windows Boot Manager:

  Windows could not start. A recent hardware or software change might be the cause. To solve the problem:

  1. Insert your windows installation disc and restart your computer. (don't have)

  2. choose your language settings, and then click "next".

  3. click on "Repair your computer."

  If you do not have this disc contact the Adminitrator's manufacturer or a computer in your system.

  Status: Oxc0000225

  Info: The boot selection failed because a required device is not accessible.

  Is there a way to get around this. I would get to it as soon as possible, but I want to wipe all my info beforehand.

  Thank you!

  Karen

  try to perform the recovery by using the partition.  boot f11 and recovery manager must take over. If not, or if the process does not finish successfully, perform a large hard drive. If the test successfully you will need to order a copy of your HP recovery disk.

  as an alternative, you can create a new admin account and simply delete your existing account after.

  hope this helps