Fret is disabled for this virtual machine

Similar Questions

• ESXi 5 - Longmode is disabled for this virtual machine.

  Hello

  I installed ESXi 5.0.0 469512 on a Dell Optiplex 755 with Intel Core 2 Duo E8400 processor @ 3 .00GHz with 4 GB of RAM. In the BIOS (version A21), I have the following options enabled:

  Performance-

  Virtualization: on

  VT for direct i/o: on

  Execution of trust: on

  Security-

  TPM security: on

  Activation of the TPM secure: assets

  Execute Disable: on

  I am unable to run any 64-bit OSs. For example, when I try to start vMA VM 5.0, I get the following Message from the Virtual Machine:

  "This virtual machine is configured for 64-bit operating systems. However, the 64-bit mode is not possible.

  Longmode is disabled for this virtual machine.
  For more information, see http://VMware.com/info?id=152 .
  Continue without 64 bit support? »

  I ran the "processor check for 64-bit compatibility ' and if confirmed I can run 64-bit guest OS.

  I tried to add vhv.allow = "TRUE" to/etc/vmware/config, but it made no difference.

  In the vmware.log file is that it makes meantion 'virtualization software is incompatible with the long mode on this platform. Disabling longmode. "I have attached the full logfile for details.

  Any help will be greatly appreciated.

  Thank you Paul.

  According to the log file

  Frequent: MSR 0x3a = 0x3--> currently '0011', should be 'x 1 x 1 "'.

  VT - x is not enabled (bit 0 + 2 required)

  There were other debates, where that allows "Trusted execution" cause problems. I "suggest that you configure the settings of the BIOS as follows:"

  Performance-

  Virtualization: on (assuming it's VT - x)

  VT for direct i/o: Off (unless you need it)

  Execution of trust: Off

  Security-

  The TPM secure security: Off

  Activation of the TPM secure: inactive

  Execute Disable: on

  After you change the settings, you will need to power cycle the system.

  André

• Change tracking (CTK) block is supported for this virtual machine, but was refused. This will increase the CPU proxy and consumption of IOP.

  I have problems with a client of VMware image-level in an EMC Avamar backup.  So far, we have not been able to find information about this message in the backup log file.  It is originally the backup to take a very long period of time (on average 10-11 hours).

  2014-02-28 14:20:57 avvcbimage < 14681 > Info: change tracking (CTK) block is supported for this virtual machine, but was refused. This will increase the CPU proxy and consumption of IOP.

  We cannot determine why CBT is "denied".  Has anyone here run across this issue before or seen any other type of backup VMware image have denied CBT?

  Everything I checked watch that CBT is successfully activated since the file vmx for the customer to the Avamar config.

  ESXi host is Enterprise Plus 4.1.0 260247

  After spending some time on this issue, the ultimate resolution withdrew the Avamar vm and then add it again.  After that, CBT began to work properly.  It seems that there is a parameter that has been 'stuck' pertaining to this virtual machine that wasn't behaving properly.

• The State of Transition (VM_STATE_ON-&gt; VM_STATE_CREATE_SNAPSHOT) not allowed for this virtual machine

  Can't figure this one out and search Google is not come with much.

  I have 13 virtual machines in my environment.  They all use the same data store.  11 of them have no problems, but 2 of them fail with this error when you try to make a snapshot.

  I tried to reboot the hypervisor and vmware vsphere services.  I tried to remove and add the virtual machines of the inventory.  None of the VMs directories have snapshot of the files already.

  This usually means that you have material non-quiescable, as a tape device connected, or you have a persistence of defined virtual disk.  I recomment you latter by default and try again, because this is the typical cause.  Otherwise, other suspects are raw disk mappings (a fibre channel LUN) sent directly to your virtual machine, which cannot be suspended or IO DirectPath devices (USB or PCI cards series you will cross TSE of the VM).  If this is the case, you're probably SOL.

  I strongly suspect that you're a mode not supported on the persistence on a virtual disk to your virtual machine.

• WAIT % - % IDLE, what is the average for a virtual machine?

  I did some research on performance of VM problems and worked with the media to see that there is maybe a bottle neck IO that occur with a virtual VMware machine I have performance problems on. The technician found that the WAITING % - % IDLE on average for this virtual machine is around 200%. The tech said it was abnormally high. I forgot to ask her what was normal but wanted to put a post to see if some people out there know what they are on average. What is an average number of see? I have the system done nothing right now and I see 579% waiting and 372% IDLE. The technology has been able to confirm that no IO queue was occurring in the VMkernel or on the HBA controller.

  Some average % positions would be useful. Thank you.

  gdewulf18480 wrote:

  Supposibly the amount of time in a State of waiting for I/O is the WAIT - IDLE % difference. I was wondering if anyone had the numbers for this feeling. Is there anyone with some of them?

  Q: How will I know the VCPU world waiting for I/O events?

  A: WAIT - % IDLE % can give you an estimate on how much time processor is spent waiting for I/O events. It is an estimate only, because the world wait perhaps for other than the i/o resources. Note that we should do it only for the worlds of the WWW, not the other kind of worlds. Because the VMM worlds represent the best guest behavior. For the disk i/o, another alternative is to read the disk latency stats that we explain in the drive section.

  WAIT % by itself cannot be used, you must develop and examine the individual vCPU % EXPECTATION values and subtract their idle time.  You can't do it on the initial view of a single line by VM CPU in esxtop.  If technology that you mentioned did not explain it, he doesn't know what it takes.

  I have lots of virtual machines that are never less than 300% when I wait - % idle and I have no problems.

  It is an example, I caught NimSoft server:

  DHSNMS1 100 100 5 192.63 193,80 0.24 0.03 291,44 1.04

  %EST USED (s) 192 - in other words, almost two processors are used 100%

  The %Idle is 1.04% WAIT 291.44 - according to the calculation of waiting idle, I have a super serious problems of e/s past  But this isn't the case, and expanding, I can see that.

  5665 vmware-vmx 100 1 0.09 0.11 100.00 0.00 0.00 0.01

  5667 100 vmassistant.566 1 0.62 0.65 99,63 0.00 0.00 0.00

  5703 100 mks:DHSNMS1 1 0.01 0.01-100.00 0.00 0.00 0.00

  5704 vcpu 100 - 0:DHSNMS1 1 32,35 32.88 67,28 0.28 0.11 67,14

  5705 vcpu 100 - 1:DHSNMS1 1 31,58 32.05 68.11 0.00 67.85 0.12

  So the changed values unfortunately because of ESXTOP bike when you develop... which is annoying, but anyway.  In this you see % waiting is 67 and 68 with another respectively being 3 to 100% (which is normal) and the idle being %, 0, 0, 0, 67 and 67.8.  Doing the calculation on the processors shows a wait - slowed virtually 0 - or very little IO wait past with processors.  But if you add up all the expectations of % and % is idling, you have 434ish, and the 134ish and do the calculation is the difference of 300 - which is the 3 who are always 100%.

  So there is no way we can answer your question, we can only help you to understand how the values should be interpreted.

  Waiting for i/o States almost always go on the disc anyway, it is unlikely, therefore, the network or the user entered, looking at the stats of disc ESXTOP is a much better way to determine if there is a problem of e/s.

• Damaged Restore points/images for a virtual machine only

  I have a vDR 1.2 with sharing CIFS 490 GB attached to it as a backup destination.

  Whenever I save one of my VM TI-error on this issue of restoration of VM and brands it damaged when you run integrity checks the next day.

  It is only on this one (Windows 200 SP4) virtual machine. I can select for deletion, then restart the integrity check that it will remove.

  But then, once I created a new backup of the VM (which always succeeds for this virtual machine) the integrity check will mark it damaged, I do not know why, always the same VM.

  It has 3 hard drives, 5, 8 and 11 GB. I have an another win 2000 SP4 virtual machine that has no problem, the touch is the only one.

  Is it possible to create another CIFS share on the same destination and then create a one-time job that comes only backup a VM?  Then see if you still get the restore points damaged.

• Affinity processor for a virtual machine

  I have a lot of CPU 8 on which I have installed ESX 3.5 U3. I also created a virtual machine Windows 2003 Server SP2 with 2 CPU is assigned to the.

  I'm trying to set the processor affinity for this virtual machine to use 2 of my physical processors. I see now on the tab Advanced CPU, I am able to select all available 8 physics of the processor. So now I'm a bit confused regarding if VMware allows scaling of my machine virtual to use all 8 CPU when my virtual machine is only 2 CPU?

  Now if the above is true, and I am to be allowed to set the affinity of the virtual machine to the all 8 CPU, then why is this maximum limit of the processor for a virtual machine is only 4? A stupid question probably but I'm really confused?  :|

  Hi confused,

  Yes, the user interface is a bit confusing. As RParker said, basically what you are doing when you assign the processor affinity are to identify the nuclei on which the vCPU is eligible to run on. At no time will be the VM scheduled to be run on carrots than what there vCPUs, so he will never have access to a capacity more than expected.

  The processor affinity is one of those features that's been around since 'the beginning' and its utility is really a bit blurred. I've heard of cases where users were running Citrix workloads configured with 2 vCPU and assigned the processor affinity for each virtual computer with the result of improving the performance. I wonder this because I never saw myself, and have a decent knowledge of how works the vmkernel Scheduler, it make much sense.

  I would encourage you (and anyone else reading this) essentially forget that the processor affinity is an option. Use it can cause significant performance degradation (if, for example, you pin a VM through two nodes NUMA, rather than keep vCPUs all in the same node) and break features (VMotion, DRS and who knows what else in the future).

  Ken Cline

  VMware vExpert 2009

  VMware communities user moderator

  Blogs about: http://KensVirtualReality.wordpress.com/

• 'Disable the alarm action' for a virtual machine

  Hello

  I want to disable all actions for a virtual machine alarm, while I have to disable FT to clone a virtual machine. My script are ready for cloning but I have a solution to disable the actions of alarm for a virtual machine via PowerCLI to can´t. Someone knows a solution for PowerCLI 5.1R1?

  Thank you

  Michael

  -Entity parameter requires an inventory of PowerCLI as value object and does not have the names. You can try it like this:

  Get-AlarmActionState-entity (Get-VM-name VMTEST1) - Recurse: $false

• Disable the clichés for individual virtual machines?

  Hi all

  Is it possible to disable support for snapshot for individual virtual machines, perhaps via a parameter for it?  Or is the closest answer you to put all its virtual disks in independent mode?  Try to see how to better meet the requirements that certain suppliers impose that the VM/device does not catch instant and thought that the best solution is to disable the feature for the specific VM (s) only.  Thank you!

  You can watch the snapshot.maxSnapshots configuration setting. See KB 1031280 for more information.

• A suspended snapshot could not be created for the virtual machine (DC) ha-data center (DC) \vm\VMware vCenter Server Appliance.

  Hello gentlemen,

  I can not only save this virtual machine with Backup Exec 2014 for a long time.

  They are there was no snapshot in snapshot Manager.

  Could you help me?

  A suspended snapshot could not be created for the virtual machine (DC) ha-data center (DC) \vm\VMware vCenter Server Appliance.

  V-79-57344-38260 - failed to create a snapshot of the virtual machine. The virtual machine is no longer exist, or may be too busy to pause to take the snap.

  A suspended snapshot could not be created for the virtual machine (DC) ha-data center (DC) \vm\FRPA111PRIM01.

  V-79-57344-38299-\vm\FRPA111PRIM01 ha-data center (DC) VMVCB::\\192.168.204.42\VCGuestVm\ (DC). To try to take a snapshot of a virtual machine failed because it could not be suspended in a file system.

  Hello

  I found the solution.

  I disabled the JOB BE general relativity.

  and the host where the virtual machine belong was not the right time. No Ntp server has been configured.

  I did and now there works.

  I think that the problem can come from this.

• DRS disabled on a virtual machine storage

  All,

  I wanted to ask what was the impact of a deactivation of DTS for an individual VM.  It always includes this virtual machine in the calculation of the space used for the SDR rules?  So I guess, and it would be just to rebalance the VM who have enabled it?

  Yes, as I said earlier, i/o and the space used by the virtual machine with DTS configured to disabled will appear in the statistics of DTS.

• Message indicates, this program requires Windows 2000 or greater must be installed in this virtual machine.

  Trying to install a new program and keep this exact error message: "implemented cannot continue." This program requires Windows 2000 or higher installed in this virtual machine. "I have Windows XP, which is higher than 2000, and I do not know how to proceed.

  It is possible that you need XP Pro (not XP Home) installed on your home desktop. You should contact VMWare technical support for this issue. You might be interested in this forum, too:

  http://communities.VMware.com/community/VMTN/desktop/view?view=discussions

  Good luck.

• This virtual machine to become protected vsphere HA and HA can not try to restart after a power failure

  I got a 5.1 cluster with some problems HA.

  a few virtual machines are showing this

  This virtual machine to become protected vsphere HA and HA can not try to restart after a power failure.

  When I try to reconfigure HA on the host. It times out and fails.

  any idea?

  Instead of reconfiguring HA on the concerned host, have you tried to disable HA on the cluster and enable again? See: VMware KB: State of the virtual machine changes from protected to Unprotected

• SRM 5.5 - vSphere replication - error: impossible to reverse the replication for the Virtual Machine. A snapshot operation cannot be performed

  Hi all, we have just run a test DR failover of a couple of virtual machines in our protected our failover site and all site swung perfectly, two virtual machines came online and all applications work well. However when we cam to r-eprotect machines virtual, we get some errors.

  One of the virtual machines seems to have lived the reprotect end process, it is still running, but has not moved to 89% for some time. The virtual machine has a couple of grand (a little less than 2 TB) VMDK. slow progress is just a consequence of the large VMDK?

  More worrisome is the virtual machine which don't reprotect at all. It generates an error whenever I click on the "Restore" button (error: impossible to reverse the replication for the Virtual Machine.) A snapshot operation can not be performed).

  
  Does anyone have any ideas as to the cause?

  Thanks in advance for any help.

  Andy

  Finally got to the bottom of this. The issue was that reprotect SRM work was trying to dispel any snapshots that were taken on the computer object virtual destination in VMWare, but could not clean snapshots.

  The reason why snapshots would not consolidate was because it was snapshots of temporary VEEAM who in fact any snapshot file listed in the VSAN data store. So when we looked through the browser data store, no snapshot file existed in the virtual computers folder. Trying a manual removal also failed.

  To fix this, we created a snapshot of the virtual machine in the original data center (note is the engine to the bottom of the virtual machine), this effect was to get rid of the 'fade' snapshot that was visible in the Snapshot Manager that VEEAM backup had left behind. Once this had disappeared, the reprotect back to DCA worked perfectly.

• Definition of levels of booking for a virtual machine

  The vcloud usage meter says:

  NET points = (vGB hours X points per 1 GB reserved RAM) / hours per month

  
  

  A month calendar of 30 days, a service provider uses the vCloud package provider services - first Edition to configure its virtual machine with 16 vGB for 15 days and 48 vGB 15 days remaining. The level of booking for the virtual machine is set to 75 percent for the whole month.

  15 days x 24 hours x 16 vGB x 0.75 = 4 320 hours of vGB

  15 days x 24 hours x 24 vGB (vGB 48 x 0.75 but capped at 24 GB) = 8 640 hours of vGB

  Total number of hours of vGB = 12 960 hours of vGB

  Total points = 12 960 vGB hours ÷ 720 hours / month x 7 points (for Prime Minister) = 126 points

  Where "the level of booking' for a virtual machine?  Is - this talk on VM bookings each parameter in vCenter Server, or do something to the extent of consumption vCloud himself?

  Hello. The reservation level is set for each virtual machine, using a vSphere Client or API.