From AnyConnect VPN through an RDP Session
Hello
We have AnyConnect (ver. 3.1.01065) set up on our ASA5520 boxes. VPN works well from the office, but I also need the ability to establish a VPN connection through a RDP connection (i.e. I use RDP to connect to a PC that has installed AnyConnect, then try to establish a VPN connection).
I downloaded the Cisco VPN profile editor, chaned the option
However, I can't yet start VPN through an RDP connection. (Error is "the ability to set up VPN for remote desktop is disabled.) A VPN connection cannot be established.") I checked the file XML on the local PC to confirm the profile was downloaded (and is, and I do not see the option AllowRemoteUsers.) This has also happened with the previous AnyConnect version (3.0.xxxx). Local routing tables of the PC look good, and I don't see any conflicts that would cause the RDP session to drop. Also - if I connect the VPN, then RDP on the PC, the VPN and the RDP sessions work fine. Any ideas would be appreciated! Thank you Tony Hi Tony,. To do this both the ASA and the client must have the same XML profile. I just tested this with AC 3.1 and ASA 8.4 and it works beautifully. I included the XML file. * BTW, make sure that the profile is assigned to the appropriate group strategy. HTH. Portu. Please note all useful posts Tags: Cisco Security Peer AnyConnect VPN cannot ping, RDP each other I have an ASA5505 running ASA 8.3 (1) and ASDM 7.1 (1). I have a remote access VPN set up and remote access users are able to connect and access to network resources. I can ping the VPN peers between the Remote LAN. My problem counterparts VPN cannot ping (RDP, CDR) between them. Ping a VPN peer of reveals another the following error in the log of the SAA. Asymmetrical NAT rules matched for flows forward and backward; Connection for icmp outside CBC: 10.10.10.8 outside dst: 10.10.10.9 (type 8, code 0) rejected due to the failure of reverse NAT. Here's my ASA running-config: ASA Version 8.3 (1) ! ciscoasa hostname domain dental.local activate 9ddwXcOYB3k84G8Q encrypted password 2KFQnbNIdI.2KYOU encrypted passwd names of ! interface Vlan1 nameif inside security-level 100 IP 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 IP address dhcp setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! passive FTP mode clock timezone CST - 6 clock to summer time recurring CDT DNS lookup field inside DNS server-group DefaultDNS 192.168.1.128 server name domain dental.local permit same-security-traffic inter-interface permit same-security-traffic intra-interface network obj_any object subnet 0.0.0.0 0.0.0.0 network of the RAVPN object 10.10.10.0 subnet 255.255.255.0 network of the NETWORK_OBJ_10.10.10.0_28 object subnet 10.10.10.0 255.255.255.240 network of the NETWORK_OBJ_192.168.1.0_24 object subnet 192.168.1.0 255.255.255.0 access-list Local_LAN_Access note VPN Customer local LAN access Local_LAN_Access list standard access allowed host 0.0.0.0 DefaultRAGroup_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0 Note VpnPeers access list allow peer vpn ping on the other permit access list extended ip object NETWORK_OBJ_10.10.10.0_28 object NETWORK_OBJ_10.10.10.0_28 VpnPeers pager lines 24 Enable logging asdm of logging of information logging of information letter address record [email protected] / * / exploitation forest-address recipient [email protected] / * / level of information record level of 1 600 6 rate-limit Outside 1500 MTU Within 1500 MTU mask 10.10.10.5 - 10.10.10.10 255.255.255.0 IP local pool VPNPool ICMP unreachable rate-limit 1 burst-size 1 ASDM image disk0: / asdm - 711.bin don't allow no asdm history ARP timeout 14400 NAT (inside, all) static source all electricity static destination RAVPN RAVPN NAT (inside, outside) static static source NETWORK_OBJ_10.10.10.0_28 destination NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_10.10.10.0_28 NAT (inside, outside) static source all all NETWORK_OBJ_10.10.10.0_28 of NETWORK_OBJ_10.10.10.0_28 static destination ! network obj_any object NAT dynamic interface (indoor, outdoor) network of the RAVPN object dynamic NAT (all, outside) interface Timeout xlate 03:00 Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00 Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00 Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-registration DfltAccessPolicy Enable http server http 192.168.1.0 255.255.255.0 inside No snmp server location No snmp Server contact Community SNMP-server
Server enable SNMP traps snmp authentication linkup, linkdown cold start Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac Crypto ipsec transform-set ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac Crypto ipsec transform-set ESP-AES-128-SHA-TRANS mode transit Crypto ipsec transform-set ESP-DES-SHA-TRANS esp - esp-sha-hmac Crypto ipsec transform-set ESP-DES-SHA-TRANS mode transit Crypto ipsec transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac Crypto ipsec transform-set ESP-AES-192-SHA-TRANS mode transit Crypto ipsec transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac Crypto ipsec transform-set ESP-AES-256-SHA-TRANS mode transit Crypto ipsec transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac Crypto ipsec transform-set ESP-3DES-SHA-TRANS mode transit life crypto ipsec security association seconds 28800 Crypto ipsec kilobytes of life - safety 4608000 association Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP ESP-AES-128-SHA ESP - AES - 192 - SHA ESP - AES - 256 - SHA ESP - 3DES - SHA - OF - SHA ESP - AES - 128 - SHA - TRANS ESP - AES - 192 - SHA - TRANS ESP - AES - 256 - SHA - ESP ESP - 3DES - SHA - TRANS TRANS-DES - SHA - TRANS outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP outside_map interface card crypto outside trustpoint crypto ca-CA-SERVER ROOM LOCAL-CA-SERVER key pair Configure CRL Crypto ca trustpoint ASDM_TrustPoint0 registration auto name of the object CN = ciscoasa billvpnkey key pair Proxy-loc-transmitter Configure CRL crypto ca server CDP - url http://ciscoasa/+CSCOCA+/asa_ca.crl name of the issuer CN = ciscoasa SMTP address [email protected] / * / crypto certificate chain ca-CA-SERVER ROOM certificate ca 01 * hidden *. quit smoking string encryption ca ASDM_TrustPoint0 certificates certificate 10bdec50 * hidden *. quit smoking crypto ISAKMP allow outside crypto ISAKMP policy 10 authentication crack aes-256 encryption sha hash Group 2 life 86400 crypto ISAKMP policy 20 authentication rsa - sig aes-256 encryption sha hash Group 2 life 86400 crypto ISAKMP policy 30 preshared authentication aes-256 encryption sha hash Group 2 life 86400 crypto ISAKMP policy 40 authentication crack aes-192 encryption sha hash Group 2 life 86400 crypto ISAKMP policy 50 authentication rsa - sig aes-192 encryption sha hash Group 2 life 86400 crypto ISAKMP policy 60 preshared authentication aes-192 encryption sha hash Group 2 life 86400 crypto ISAKMP policy 70 authentication crack aes encryption sha hash Group 2 life 86400 crypto ISAKMP policy 80 authentication rsa - sig aes encryption sha hash Group 2 life 86400 crypto ISAKMP policy 90 preshared authentication aes encryption sha hash Group 2 life 86400 crypto ISAKMP policy 100 authentication crack 3des encryption sha hash Group 2 life 86400 crypto ISAKMP policy 110 authentication rsa - sig 3des encryption sha hash Group 2 life 86400 crypto ISAKMP policy 120 preshared authentication 3des encryption sha hash Group 2 life 86400 crypto ISAKMP policy 130 authentication crack the Encryption sha hash
Group 2 life 86400 crypto ISAKMP policy 140 authentication rsa - sig the Encryption sha hash Group 2 life 86400 crypto ISAKMP policy 150 preshared authentication the Encryption sha hash Group 2 life 86400 enable client-implementation to date Telnet 192.168.1.1 255.255.255.255 inside Telnet timeout 5 SSH timeout 5 Console timeout 0 management-access inside dhcpd outside auto_config ! dhcpd address 192.168.1.50 - 192.168.1.99 inside dhcpd allow inside ! a basic threat threat detection threat detection statistics a statistical threat detection tcp-interception rate-interval 30 burst-400-rate average rate 200 SSL-trust outside ASDM_TrustPoint0 point WebVPN allow outside SVC disk0:/anyconnect-win-3.1.04072-k9.pkg 1 image SVC profiles DellStudioClientProfile disk0: / dellstudioclientprofile.xml enable SVC
tunnel-group-list activate internal-password enable chip-tunnel list SmartTunnelList RDP mstsc.exe windows platform internal DefaultRAGroup group strategy attributes of Group Policy DefaultRAGroup Server DNS 192.168.1.128 value Protocol-tunnel-VPN l2tp ipsec Split-tunnel-policy tunnelspecified value of Split-tunnel-network-list DefaultRAGroup_splitTunnelAcl Dental.local value by default-field WebVPN SVC value vpngina modules internal DefaultRAGroup_1 group strategy attributes of Group Policy DefaultRAGroup_1 Server DNS 192.168.1.128 value Protocol-tunnel-VPN l2tp ipsec Dental.local value by default-field attributes of Group Policy DfltGrpPolicy Server DNS 192.168.1.128 value VPN - 4 concurrent connections Protocol-tunnel-VPN IPSec l2tp ipsec svc webvpn value of group-lock RAVPN value of Split-tunnel-network-list Local_LAN_Access Dental.local value by default-field WebVPN the value of the URL - list DentalMarks SVC value vpngina modules SVC value dellstudio type user profiles SVC request to enable default webvpn chip-tunnel enable SmartTunnelList wketchel1 5c5OoeNtCiX6lGih encrypted password username username wketchel1 attributes VPN-group-policy DfltGrpPolicy WebVPN SVC value DellStudioClientProfile type user profiles username privilege 15 encrypted password 5c5OoeNtCiX6lGih wketchel username wketchel attributes VPN-group-policy DfltGrpPolicy WebVPN modules of SVC no SVC value DellStudioClientProfile type user profiles jenniferk 5.TcqIFN/4yw0Vq1 of encrypted password privilege 0 username jenniferk username attributes VPN-group-policy DfltGrpPolicy WebVPN SVC value DellStudioClientProfile type user profiles attributes global-tunnel-group DefaultRAGroup address pool VPNPool LOCAL authority-server-group IPSec-attributes tunnel-group DefaultRAGroup pre-shared key *. tunnel-group DefaultRAGroup ppp-attributes PAP Authentication ms-chap-v2 authentication eap-proxy authentication type tunnel-group RAVPN remote access attributes global-tunnel-group RAVPN address pool VPNPool LOCAL authority-server-group tunnel-group RAVPN webvpn-attributes enable RAVPN group-alias IPSec-attributes tunnel-group RAVPN pre-shared key *. tunnel-group RAVPN ppp-attributes PAP Authentication ms-chap-v2 authentication eap-proxy authentication type tunnel-group WebSSLVPN remote access tunnel-group WebSSLVPN webvpn-attributes enable WebSSLVPN group-alias ! class-map inspection_default match default-inspection-traffic ! ! type of policy-card inspect dns preset_dns_map parameters maximum message length automatic of customer message-length maximum 512 Policy-map global_policy class inspection_default inspect the preset_dns_map dns inspect the ftp inspect h323 h225 inspect the h323 ras inspect the rsh inspect the rtsp inspect esmtp inspect sqlnet inspect the skinny inspect sunrpc inspect xdmcp
inspect the sip inspect the netbios inspect the tftp Review the ip options ! global service-policy global_policy 173.194.64.108 SMTP server context of prompt hostname HPM topN enable Cryptochecksum:3304bf6dcf6af5804a21e9024da3a6f8 : end Hello Seems to me that you can clean the current NAT configuration a bit and make it a little clearer. I suggest the following changes network of the VPN-POOL object 10.10.10.0 subnet 255.255.255.0 the object of the LAN network subnet 192.168.1.0 255.255.255.0 PAT-SOURCE network object-group object-network 192.168.1.0 255.255.255.0 object-network 10.10.10.0 255.255.255.0 NAT static destination LAN LAN (indoor, outdoor) static source VPN-VPN-POOL destination VPN VPN-POOL POOL static NAT (outside, outside) 1 static source VPN-VPN-POOL NAT interface (it is, outside) the after-service automatic PAT-SOURCE dynamic source The above should allow You can then delete the previous NAT configurations. Naturally, please save the configuration before you make the change, if you want to revert to the original configuration. no static source nat (inside, everything) all electricity static destination RAVPN RAVPN
No source (indoor, outdoor) nat static static NETWORK_OBJ_10.10.10.0_28 destination NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_10.10.10.0_28 No source (indoor, outdoor) nat static everything all NETWORK_OBJ_10.10.10.0_28 of NETWORK_OBJ_10.10.10.0_28 static destination No network obj_any object No network object RAVPN In case you do not want to change the settings a lot you might be right by adding this network of the VPN-POOL object 10.10.10.0 subnet 255.255.255.0 destination VPN VPN-POOL POOL static NAT (outside, outside) 1 static source VPN-VPN-POOL But the other above configurations changes would make NAT configurations currently simpler and clearer to see every goal of "nat" configurations. -Jouni AnyConnect VPN session disconnect and reconnect I have a firewall cisco ASA 5525-X set up to accept the AnyConnect VPN client (IKEv2) connection. AnyConnect VPN client can successfully connect. During the 1st 10 minutes after logging in, will the client Anyconnect VPN lost VPN connection for a few seconds (ranging from 3 seconds to 10 seconds), then it automatically reconnect back. After that, no more lost connection times. The lost connection happened at all multiple. So far, all at least 4 show the same problem. It does not affect the operation of the network, but it gives an unpleasant impression for users. I tried to surveillance of the ASDM firewall logs, no newspaper of no errors. I use Wireshark to capture traffic on the client side, also no errors detected. Can idea how I can continue to troubleshoot this problem? Hi Limlayhin, You can go ahead and capture logs of dart. You can download the Pack of dart for the anyconnect version you use and that you run after you experience this problem. Please make sure that everything you clear observer logs event before you launch you the Anyconnect client. To clear the observer event logs, follow these steps: 1. start > run > Eventvwr 2. it will then open Event Viewer Window 3 maximize the application logs and services and that you will find an option "Cisco Anyconnect Secure Mobility Client" 4. right click on the Cisco Anyconnect Secure Mobility Client and select clear logs. Select clear after that. Once you are done with this, launch the anyconnect connection and allow the problem to happen. Once the problem occurs, unplug the anyconnect client and run newspapers dart. It will create a Zip file on your desktop (by default) and you can go through the logs of connection Anyconnect to look for the root cause. Let me know if it helps. Vishnu AnyConnect SSL VPN through IPSEC Tunnel Everyone was able to set up and connect using Cisco anyconnect vpn ssl on a Cisco IPSEC's tunnel. I used this in the past from a Windows XP system in the past but its not working now. None of my users are able to cooect using the Anyconnect on IPSEC. IPSEC on its own works very well. The Anyconnect is also able to create the connection to its ASA firewall however its not able to route all traffic through. Do you have any suggestions? Thanks for the update. My first time using this service, please be gentle. I have installed recently an anyconnect vpn for a specific application. My question, if I use the command "see the conn." VPN01 # sh conn | I have 172.18.7.36 UDP outside 172.18.7.36:1123 DMZ_ADM 10.7.16.57:81, idle 0:00:00, bytes 73324, flags. UDP outside 172.18.7.36:1123 DMZ_ADM 10.7.32.107:81, idle 0:00:00, bytes 73232, flags. UDP outside 172.18.7.36:1123 DMZ_ADM 10.7.32.41:81, idle 0:00:00, bytes 73232, flags. UDP outside 172.18.7.36:81 DMZ_ADM 10.7.32.41:3765, idle 0:00:02, 5075905 bytes, flags. UDP outside outside 172.18.7.30:81 172.18.7.36:1123, idle 0:00:00, bytes 73186, flags. UDP outside outside 172.18.7.37:81 172.18.7.36:1123, idle 0:00:00, 16744 bytes, flags. VPN01 #. In the list above, I know this 172.18.7.30 device is not connected (at least 3 hours). Why do I see a UDP session between 172.18.7.30 and 172.18.7.36? My interpretation of a UDP session is incorrect? Notice that I use the version Cisco Adaptive Security Appliance Software Version 8.3 (1) AnyConnect-victory - 2.4.1012 - k9.pkg Thanks for your help. Sergio Great observation and thanks for the update. Please kindly marks the message as response while others may learn from your post and thank you for the update of the majority with the description complete. The anyconnect vpn easy vpn Remote communication problem Hi team, I have a problem of communication of the anyconnect vpn easy vpn Remote I´ll explain better below and see the attachment (1) VPN Tunnel between branch HQ - That´s OK The idea is that the Anyconnect Client is reaching the local Branch Office network, but has not reached. Could you help me? ASA5505 Version 8.4 (7) 23 (Headquarters) Configuration of the server easy VPN (HQ) *. Crypto dynamic-map DYNAMIC - map 5 set transform-set ESP-AES-256-SHA ikev1 ACL_EZVPN list standard access allowed 10.0.0.0 255.255.255.0 internal EZVPN_GP group policy object-group network Obj_VPN_anyconnect-local Remote AnyConnect VPN - Obj anyconnect-remote non-proxy-arp-search to itinerary NAT_EZVPN_Destination no-proxy-arp-search to itinerary NAT_EZVPN_Destination NAT_EZVPN_Destination non-proxy-arp-search route Configuration VPN AnyConnect (HQ) *. WebVPN tunnel of splitting allowed access list standard 192.168.1.0 255.255.255.0 internal clientgroup group policy type tunnel-group sslgroup remote access object-group network Obj_VPN_anyconnect-local
Remote AnyConnect VPN - Obj anyconnect-remote non-proxy-arp-search to itinerary NAT_EZVPN_Destination no-proxy-arp-search to itinerary NAT_EZVPN_Destination NAT_EZVPN_Destination non-proxy-arp-search route Hello communication works when you send the traffic of easyvpn derivation because it froms the IPSEC SA to pool local subnet and anyconnect HQ. The SA formed only when the branch initiates the connection as it's dynamic peer connection to HQ ASA. When there no SA between branch and HQ for this traffic, HQ ASA has no idea on where to send the anyconnect to network traffic. I hope this explains the cause. Kind regards Averroès. Hello I have configured AnyConnect VPN with split tunneling, so my internal networks is in the tunnel and get internet directly (not via an internal network). But we want to access one of the public IP (8.8.8.8) through AnyConnect VPN tunnel. When we check the capture of packets on an external interface, trying to ping 8.8.8.8 showing the icmp-request package but not get icmp-response packages. Additional configuration required to access the ip address above by tunnel? We have activated the below configuration as well. permit same-security-traffic intra-interface permit same-security-traffic inter-interface Please find details of the capture below: 192.168.18.71 is my ip from the pool AnyConnect VPN system. 114 extended access-list allow ip host 192.168.18.71 8.8.8.8 output interface of capture within the list of access-114 See the capture of xxx - ASA (config) # outgoing 1: 22:13:24.001800 192.168.18.71 > 8.8.8.8: icmp: echo request 0 packets captured 0 illustrated package 0 packets captured 0 illustrated package Kindly help us solve the problem. Thank you and best regards, Ashok I like to use the notation NAT object instead. So maybe try: Hello people! I would like to know how I can see the story of anyconnect VPN. See current webvpn or ssl vpn client session, I now this command can be using, but I Don t know about history. Thank you Marcio Hi Marcio, To do this you must configure a syslog server. Please visit this link: http://www.Cisco.com/c/en/us/support/docs/security/PIX-500-series-Securi... You would be able to extract the information from the Anyconnect users who have a link in the past. It will be useful. Kind regards Aditya Please evaluate the useful messages. ASA Anyconnect VPN do not work or download the VPN client I have a Cisco ASA 5505 that I try to configure anyconnect VPN and thought, I've changed my setup several times but trying to access my static public IP address of the external IP address to download the image, I am not able to. Also when I do a package tracer I see he has been ignored through the acl when the packets from side to the ASA via port 443, it drops because of the ACL. My DMZ so will he look like something trying to access the ASA via the VPN's going to port 443. Here is my config XXXX # sh run
DHCP-client update dns
XXXX #. You do not have this configuration: Try and take (or delete): Hi all, I'm going to have bad configure anyconnect VPN on my router. I'm CCENT pre level and especially followed a tutorial, but feel I'm missing something simple here. It's a fairly simple installation on a Cisco No. 2851 - faces of a single interface my LAN 192.168.1.0/24, the other has a public IP address. I created a network 192.168.2.0/24 VPN users, mainly to have phones Android connection of their mobile phone networks, and have access to the servers/security cameras/etc by using their local IP addresses. When my phone connects, it gets an IP address and is connected, but is not communicating with my LAN correctly. The VPN client can ping 192.168.1.254 (the router's LAN IP) - but not the other devices on the network. However, the devices on my LAN can ping the VPN clients to their address 192.168.2.x. Here's a copy of my current config, I have reorganized some elements with #s. Also pasted my ip sh road under him. Do not forget that I am a novice, please forgive the hack :) Router (config) #do sh run Current configuration: 5782 bytes #########################
Gateway of last resort is #. ###. ###. # network 0.0.0.0 S * 0.0.0.0/0 [254/0] via #. ###. ###.1 can you try to disable the FW on your internal lan hosts and then try and ping from users of vpn client Anyconnect VPN migration issues Hi, I do Anyconnect VPN from an ASA ASA migration another. I need your suggestion. Migration must transfer customization and anyconnect vpn configuration. After that I reviewed some documents, looks like the configuration and customization are not the only thing that needs to be transferred. Everything can give some suggestion exactly what needs to be transferred in addition to customization and configuration vpn? Thank you Hello Although the copy of the configuration of one firewall to another will get all the anyconnect rules and the installation program completed, but the flash content (IE anyconnect programs, profiles anyconnect, customizations anyconnect, bookmarks, and dap profiles) is not transferred to the other ASA. They must be downloaded manually to the ASA again. Another way to do this is through ASDM, Go to tools > configuration backup: Select the components of the VPN you want to create a backup for. NOTE *. Otherwise, you can go the ususal path, the anyconnect first configuration copy and then manually transfer components anyconnect flash of one ASA to another. ********** Kind regards PS Please rate helpful messages. Would become Anyconnect essentials Premium AnyConnect vpn on asa Dear team, We have a pair of cisco ASA 5520 with version 8.2 (5) works well with active mode / standby. As the situation requires, we intend to change the SSL vpn to clientless SSL VPN (AnyConnect Premium) to anyconnect vpn with mobile clients (IOS & Android) Please specify below (1) I have read, we cannot have two Anyconnect Essentials & AnyConnect Premium on the same system time. We need to disable accordingly to our need-pl correct me? (2) what is the best way to have the device for end-user client deployment? pushing of ASA or install individually on the system? Can I have the best, I mean the latest version of windows, client MAC e.t.c I shud get? While pushing ASA LU that much memory cache will be used, since we have IPS (AIP - SSM) modules has also installed on ASA who shud method I adopt here? (3) what is the exact product for license Anyconnect Essentials & customer name mobile (IOS & Android) we get from cisco? (4) once I get the correct license how do I active in systems? should I remove the failover command and install the license in two devices separately? (5) Finally, I need to authenticate vpn anyconnect essentials with LDAP that is already configured for clientless SSL VPN(AnyConnect Premium). any suggestions here? Below the version Sh emitted by the devices, it seems essential Anyconnect is already active... Please correct me? Active Firewall System image file is "disk0: / asa825 - k8.bin. Material: ASA5520, 2048 MB RAM, Pentium 4 Celeron 2000 MHz processor Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0) 0: Ext: GigabitEthernet0/0: the address is a493.4ca3.ce0a, irq 9 The devices allowed for this platform: This platform includes an ASA 5520 VPN Plus license. ===================================================== Firewall standby Updated Saturday, May 20, 11 16:00 by manufacturers Material: ASA5520, 2048 MB RAM, Pentium 4 Celeron 2000 MHz processor Hardware encryption device: edge Cisco ASA - 55 x 0 Accelerator (revision 0 x 0) 0: Ext: GigabitEthernet0/0: the address is 6073.5cab.3fae, irq 9
The devices allowed for this platform: This platform includes an ASA 5520 VPN Plus license. Thank you 1 correct. You can run one or the other, but not both. 2 since you have the upgrade memory to 2 GB, you should be fine perform web deployment via the pkg file method. 3. for a 5520, you need: L-ASA-AC-E-5520 = .. .to the Essentials and Mobile licenses respectively. 4. on ASA 8.2, you need licenses for both units. If you upgrade to 8.3 + (8.4 (7) recommend at least), you can share licenses between members of a pair of HA. If you choose not to upgrade, just apply the key of activation on the rescue unit, then on the unit activates. You don't need to move on and in the failover configuration. Failover of the rescue unit status will show as ineligible briefly while he holds the new license is not the case of the active unit. Which will be resolved after you have applied the same license on the main unit. (If you were on 8.3 + would not happen at all). 5. simply create a new connection profile for customers of Essentials by using the same AAA server group. ASA 5512 Anyconnect VPN cannot connect inside the network 9.1 x Hello I'm new to ASA, can I please help with this. I managed to connect to the vpn through the mobility cisco anyconnect client, but I am unable to connect to the Internet. the allocated ip address was 172.16.1.60 and it seems OK, I thought my acl and nat is configured to allow and translate the given vpn ip pool but I'm not able to ping anything on the inside. If anyone can share some light... There's got to be something escapes me... Here's my sh run Thank you Raul ------------------------------------------------------------------------------- DLSYD - ASA # sh run : Saved Hello Add just to be sure, the following configurations related to ICMP traffic Policy-map global_policy
Your NAT0 configurations for traffic between LAN and VPN users seem to. Your Split Tunnel ACL seems fine too because it has included 192.168.0.0/16. I don't know what are the other. I wonder if this is a test installation since you don't seem to have a dynamic PAT configured for your local network at all. Just a few static PAT and the NAT0 for VPN configurations. If it is a test configuration yet then confirmed that the device behind the ASA in the internal network has a default route pointing to the ASAs interface and if so is it properly configured? Can you same ICMP the directly behind the ASA which is the gateway to LANs?
If you want to try ICMP interface internal to the VPN ASA then you can add this command and then try ICMP to the internal interface of the ASA Int Management-access As the post is a little confusing in the sense that the subject talk on the traffic doesn't work not internal to the network, while the message mentions the traffic to the Internet? I guess you meant only traffic to the local network because you use Split Tunnel VPN, which means that Internet traffic should use the VPN local Internet users while traffic to the networks specified in the ACL Tunnel Split list should be sent to the VPN. -Jouni AnyConnect VPN full tunnel could not access the site to site VPN I have a set of AnyConnect VPN upward with no split tunneling (U-turning/crossed traffic), running 8.2.5 code. It works fine, but I want to allow customers to AnyConnect VPN site to site, which I was unable to access. I checked the IP addresses of network anyconnect are part of the tunnel on both sides. My logic tells me that I must not turn back traffic from the network anyconnect for the site to site VPN, but I don't know how to do this. Any help would be appreciated. Here are the relevant parts of my config: (Domestic network is 192.168.0.0/24, the AnyConnect network is 192.168.10.0/24, site to site VPN network is 192.168.2.0/24) -------------------------------------------------------------------------------------- permit same-security-traffic inter-interface the DM_INLINE_NETWORK_1 object-group network outside_1_cryptomap list extended access allowed object-group ip DM_INLINE_NETWORK_1 192.168.2.0 255.255.255.0 mask 192.168.10.2 - 192.168.10.254 255.255.255.0 IP local pool AnyConnectPool Your dial-up VPN traffic as originating apears on the external interface, so I think you need to exonerate NAT pool PN traffic directed to the site to site VPN. Something like this: ASA checks AnyConnect VPN computer name Hi all I have searched the Forum and documentation, but have not found a solution to my problem. I'm guessing it happens sometimes, but maybe I'm looking for the wrong thing. We AnyConnect deployed across our cell phones, but have trouble with employees who do get the software from other sources AnyConnect and install on personal computers. We are an agency, although relatively small, but we have policies in place and I need to lock for users unable to connect to the VPN unless you're a book PC connected to our AD domain. I found a possible solution is to use dynamic access within the ASA policies to check the Windows computer name. So I set up LDAP and has created a policy to check an AAA attribute. It lets me select "MemberOf", which I assume it is the Group of users, but I need to check the name of the computer on the client before allowing access. Step by step of what I did, does anyone know of a more logical or easier way to lock on what AnyConnect VPN client computers can be used? Or if I go about this common sense with dynamic access policies, anyone have any suggestions or knowledge of documentation that helps to configure things properly when you check the computer name LDAP attribute? Thank you! JD Hey Joe, You do not need LDAP to do this, what you need is CSD (Cisco Secure Desktop) combined with DAP. Once you enable SSC, edit your DAP strategy and instead of an IPN to attribute you to try, add an attribute of endpoint (on the right hand side). To verify the host name, select the type of the attribute "peripheral". Alternatively, you can also activate the sweep of host (under Contract) and let the CSD to check the presence of a file with a certain file name, or a registry entry or a process name. CSD passes the result of this verification to the PAD, so you can use it in a policy (attributes of endpoint of type process, registry and files). Another alternative is to use the CSD with a policy before opening session - that you cannot check the host name, but it does not have control over the IP, OS type, certificate as well as the presence of a process, the registry key, the file. In this case you need not to DAP. HTH Herbert How to increase the size of the fonts in the Inbox subject, From, Date, etc. About the image below, I don't see a way in the settings to increase the sizes of police in this area. For loop runs with the value of N unwired In this case will be a loop run connected to the loop N worthless? I have seen a few examples of the loop for run without a certain number of times set to be ran wired or for example a size of table or something like that. A210 will not be upgraded to Jelly Bean I am trying to upgrade my new A210 to Jelly Bean but impossible to get the upgrade to work. I downloaded the file JB OS on Acer website but when I extract it (on a laptop Win 8) as described in the instructions, but several folders full of files and No audio device installed-HP Pavilion dv6000 No audio device installed! Help, please! No sound! I've tried EVERYTHING! If the new version of Itunes is out, version 10, and I decided to upgrade. After the upgrade, however, I have lost all sound. The low speaker has that a x I googled this proble Hi everyone, I have a little problem. In my application, I have 3 VerticalFieldManager (value for money): | Value for money: a few buttons/labels | | | ------------------------------------------------ | VFM2:here, I'm a | | TableLayoutManager * | | |Similar Questions
Version 6.3 Device Manager (1)
topology:
(2) VPN Tunnel between Client AnyConnect to HQ - that s OK
Communication is established just when I begin a session (icmp or rdp) branch to the AnyConnect Client,.
in this way, the communication is OK, but just for a few minutes.
Below the IOS version and configurations
ASA5505 Version 7.0000 23 (branch)
Crypto card outside-link-2_map 1 ipsec-isakmp DYNAMIC-map Dynamics
Crypto map link-outside-2_map-65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
Crypto map interface outside-link-2_map outside-link-2
ACL_EZVPN list standard access allowed 192.168.1.0 255.255.255.0
ACL_EZVPN list standard access allowed 192.168.50.0 255.255.255.0
ACL_EZVPN list standard access allowed 10.10.0.0 255.255.255.0
EZVPN_GP group policy attributes
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list ACL_EZVPN
allow to NEM
type tunnel-group EZVPN_TG remote access
attributes global-tunnel-group EZVPN_TG
Group Policy - by default-EZVPN_GP
IPSec-attributes tunnel-group EZVPN_TG
IKEv1 pre-shared-key *.
object-network 192.168.1.0 255.255.255.0
object-network 192.168.15.0 255.255.255.0
object-group network Obj-VPN-anyconnect-remote
object-network 192.168.50.0 255.255.255.0
the NAT_EZVPN_Source object-group network
object-network 192.168.1.0 255.255.255.0
object-network 10.10.0.0 255.255.255.0
the NAT_EZVPN_Destination object-group network
object-network 10.0.0.0 255.255.255.0
destination of Obj_VPN_anyconnect local Obj_VPN_anyconnect-local static NAT (inside, outside-link-2) Obj - VPN static source -.
destination NAT (inside, outside-link-2) static source NAT_EZVPN_Source NAT_EZVPN_Source NAT_EZVPN_Destination static
NAT (outside-link-2, outside-link-2) static source Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote static destination
Select the outside link 2
by default-idle-timeout 60
AnyConnect essentials
AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
AnyConnect profiles Remote_Connection_for_TS_Users disk0: / remote_connection_for_ts_users.xml
AnyConnect enable
tunnel-group-list activate
tunnel of splitting allowed access list standard 192.168.15.0 255.255.255.0
tunnel of splitting allowed access list standard 10.0.0.0 255.255.255.0
attributes of the strategy of group clientgroup
WINS server no
value of server DNS 192.168.1.41
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value split tunnel
ipconnection.com.br value by default-field
WebVPN
AnyConnect Dungeon-Installer installed
time to generate a new key 30 AnyConnect ssl
AnyConnect ssl generate a new method ssl key
AnyConnect value Remote_Connection_for_TS_Users type user profiles
AnyConnect ask flawless anyconnect
tunnel-group sslgroup General-attributes
address vpnpool pool
authentication-server-group DC03
Group Policy - by default-clientgroup
tunnel-group sslgroup webvpn-attributes
enable IPConnection-vpn-anyconnect group-alias
object-network 192.168.1.0 255.255.255.0
object-network 192.168.15.0 255.255.255.0
object-group network Obj-VPN-anyconnect-remote
object-network 192.168.50.0 255.255.255.0
the NAT_EZVPN_Source object-group network
object-network 192.168.1.0 255.255.255.0
object-network 10.10.0.0 255.255.255.0
the NAT_EZVPN_Destination object-group network
object-network 10.0.0.0 255.255.255.0
destination of Obj_VPN_anyconnect local Obj_VPN_anyconnect-local static NAT (inside, outside-link-2) Obj - VPN static source -.
destination NAT (inside, outside-link-2) static source NAT_EZVPN_Source NAT_EZVPN_Source NAT_EZVPN_Destination static
NAT (outside-link-2, outside-link-2) static source Obj-VPN-anyconnect-remote Obj-VPN-anyconnect-remote static destination
115 extended access-list allow host 8.8.8.8 ip 192.168.18.71
Capture interface entering inside the access-list 115
2: 22:13:28.986139 192.168.18.71 > 8.8.8.8: icmp: echo request
3: 22:13:33.970561 192.168.18.71 > 8.8.8.8: icmp: echo request
4: 22:13:38.971156 192.168.18.71 > 8.8.8.8: icmp: echo request
5: 22:13:44.080058 192.168.18.71 > 8.8.8.8: icmp: echo request
5 packs shown
XXX - ASA (config) #.
XXX - ASA (config) #.
XXX - ASA (config) # display incoming capture
XXX - ASA (config) # display incoming capture
object network obj-192.168.18.0 nat (outside,outside) dynamic interface
ASA # display webvpn vpn-sessiondb
or ASA # display vpn-sessiondb svc
: Saved
:
ASA Version 8.4 (3)
!
hostname XXXX
search for domain name
activate pFTzVNrKdD9x5rhT encrypted password
zPBAmb8krxlXh.CH encrypted passwd
names of
!
interface Ethernet0/0
Outside-interface description
switchport access vlan 20
!
interface Ethernet0/1
Uplink DMZ description
switchport access vlan 30
!
interface Ethernet0/2
switchport access vlan 10
!
interface Ethernet0/3
switchport access vlan 10
!
interface Ethernet0/4
Ganymede + ID description
switchport access vlan 10
switchport monitor Ethernet0/0
!
interface Ethernet0/5
switchport access vlan 10
!
interface Ethernet0/6
switchport access vlan 10
!
interface Ethernet0/7
Description Wireless_AP_Loft
switchport access vlan 10
!
interface Vlan10
nameif inside
security-level 100
IP 192.168.10.1 255.255.255.0
!
interface Vlan20
nameif outside
security-level 0
IP address x.x.x.249 255.255.255.248
!
Vlan30 interface
no interface before Vlan10
nameif dmz
security-level 50
IP 172.16.30.1 255.255.255.0
!
boot system Disk0: / asa843 - k8.bin
passive FTP mode
DNS lookup field inside
DNS domain-lookup outside
DNS domain-lookup dmz
DNS server-group DefaultDNS
Name-Server 8.8.8.8
Server name 8.8.4.4
search for domain name
network obj_any1 object
subnet 0.0.0.0 0.0.0.0
network of the Webserver_DMZ object
Home 172.16.30.8
network of the Mailserver_DMZ object
Home 172.16.30.7
the object DMZ network
172.16.30.0 subnet 255.255.255.0
network of the FTPserver_DMZ object
Home 172.16.30.9
network of the Public-IP-subnet object
subnet x.x.x.248 255.255.255.248
network of the FTPserver object
Home 172.16.30.8
network of the object inside
192.168.10.0 subnet 255.255.255.0
network of the VPN_SSL object
10.101.4.0 subnet 255.255.255.0
outside_in list extended access permit tcp any newspaper object Mailserver_DMZ eq www
outside_in list extended access permit tcp any newspaper EQ 587 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper SMTP object Mailserver_DMZ eq
outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq pop3 object
outside_in list extended access permit tcp any newspaper EQ 2525 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper of the Mailserver_DMZ eq imap4 object
outside_in list extended access permit tcp any newspaper EQ 465 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper EQ 993 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper EQ 995 object Mailserver_DMZ
outside_in list extended access permit tcp any newspaper EQ 5901 Mailserver_DMZ object
outside_in list extended access permit tcp any newspaper Mailserver_DMZ eq https object
Note access list ACL for VPN Tunnel from Split vpn_SplitTunnel
vpn_SplitTunnel list standard access allowed 192.168.10.0 255.255.255.0
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer to 8192
logging trap warnings
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
MTU 1500 dmz
local pool VPN_SSL 10.101.4.1 - 10.101.4.4 255.255.255.0 IP mask
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 647.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source inside inside static destination VPN_SSL VPN_SSL
NAT (exterior, Interior) static source VPN_SSL VPN_SSL
!
network obj_any1 object
NAT static interface (indoor, outdoor)
network of the Webserver_DMZ object
NAT (dmz, outside) static x.x.x.250
network of the Mailserver_DMZ object
NAT (dmz, outside) static x.x.x.. 251
the object DMZ network
NAT (dmz, outside) static interface
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 x.x.x.254 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol Ganymede HNIC +.
AAA-server host 192.168.10.2 HNIC (inside)
Timeout 60
key *.
identity of the user by default-domain LOCAL
Console HTTP authentication AAA HNIC
AAA console HNIC ssh authentication
Console AAA authentication telnet HNIC
AAA authentication secure-http-client
http 192.168.10.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ca trustpoint localtrust
registration auto
Configure CRL
Crypto ca trustpoint VPN_Articulate2day
registration auto
name of the object CN = vpn.articulate2day.com
sslvpnkey key pair
Configure CRL
Telnet 192.168.10.0 255.255.255.0 inside
Telnet timeout 30
SSH 192.168.10.0 255.255.255.0 inside
SSH timeout 15
SSH version 2
Console timeout 0
No vpn-addr-assign aaa
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd outside auto_config
!
dhcpd address 192.168.10.100 - 192.168.10.150 inside
dhcpd allow inside
!
dhcpd address dmz 172.16.30.20 - 172.16.30.23
dhcpd enable dmz
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
authenticate the NTP
NTP server 192.168.10.2
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-linux-64-3.1.06079-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
internal VPN_SSL group policy
VPN_SSL group policy attributes
value of server DNS 8.8.8.8
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list vpn_SplitTunnel
the address value VPN_SSL pools
WebVPN
activate AnyConnect ssl dtls
AnyConnect Dungeon-Installer installed
AnyConnect ssl keepalive 15
AnyConnect ssl deflate compression
AnyConnect ask enable
ronmitch50 spn1SehCw8TvCzu7 encrypted password username
username ronmitch50 attributes
type of remote access service
type tunnel-group VPN_SSL_Clients remote access
attributes global-tunnel-group VPN_SSL_Clients
address VPN_SSL pool
Group Policy - by default-VPN_SSL
tunnel-group VPN_SSL_Clients webvpn-attributes
enable VPNSSL_GNS3 group-alias
type tunnel-group VPN_SSL remote access
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect esmtp
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:d41d8cd98f00b204e9800998ecf8427e
: end object network DMZ nat (dmz,outside) static interface
object network DMZ nat (dmz,outside) dynamic interface
Building configuration...
!
! Last modification of the configuration at 02:24:24 UTC Sat Sep 5 2015 by #.
!
version 15.1
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
host name #.
!
boot-start-marker
boot-end-marker
!
!
enable secret $5 1$ 0 #.
!
AAA new-model
!
!
AAA authentication login default local
AAA authentication login local sslvpn
AAA authorization exec default local
!
!
!
!
!
AAA - the id of the joint session
!
!
dot11 syslog
no ip source route
!
!
IP cef
!
DHCP excluded-address 192.168.1.200 IP 192.168.1.254
DHCP excluded-address 192.168.1.1 IP 192.168.1.10
!
pool of dhcp IP LAN
network 192.168.1.0 255.255.255.0
Server DNS 192.168.1.254
by default-router 192.168.1.254
!
!
IP domain name # '.com'
host IP Switch 192.168.1.253
8.8.8.8 IP name-server
block connection-for 2000 tent 4 within 60
connection access silencer-class SSH_MGMT
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
!
!
!
!
!
!
!
!
!
voice-card 0
!
Crypto pki token removal timeout default 0
!
Crypto pki trustpoint TRUSTPOINT-MY
enrollment selfsigned
Serial number
name of the object CN = 117-certificate
crl revocation checking
rsakeypair my-rsa-keys
!
!
MY-TRUSTPOINT crypto pki certificate chain
certificate self-signed 01
##########################
quit smoking
!
!
license udi pid CISCO2851 sn FTX1026A54Y
# 5 secret username $1$ yv # E9.
# 5 secret username $1$ X0nL ###kO.
!
redundancy
!
!
property intellectual ssh version 2
!
!
!
!
!
!
!
!
interface GigabitEthernet0/0
LAN description
IP 192.168.1.254 255.255.255.0
IP nat inside
No virtual-reassembly in ip
automatic duplex
automatic speed
!
interface GigabitEthernet0/1
WAN description
No dhcp client ip asks tftp-server-address
No dhcp ip client application-domain name
DHCP IP address
IP access-group ACL-WAN_INTERFACE in
no ip redirection
no ip proxy-arp
NAT outside IP
No virtual-reassembly in ip
automatic duplex
automatic speed
No cdp enable
!
interface Serial0/0/0
no ip address
Shutdown
!
interface virtual-Template1
!
local IP 192.168.2.100 WEBVPN-POOL pool 192.168.2.110
IP forward-Protocol ND
no ip address of the http server
no ip http secure server
!
!
The dns server IP
IP nat inside source list INSIDE_NAT_ADDRESSES interface GigabitEthernet0/1 overload
!
IP access-list standard INSIDE_NAT_ADDRESSES
permit 192.168.1.0 0.0.0.255
permit 192.168.2.0 0.0.0.255
IP access-list standard SSH_MGMT
permit 192.168.1.0 0.0.0.255
permit 207.210.0.0 0.0.255.255
!
IP extended ACL-WAN_INTERFACE access list
deny udp any any eq snmp
TCP refuse any any eq field
TCP refuse any any eq echo
TCP refuse any any day eq
TCP refuse any any eq chargen
TCP refuse any any eq telnet
TCP refuse any any eq finger
deny udp any any eq field
deny ip 127.0.0.0 0.255.255.255 everything
deny ip 192.168.0.0 0.0.255.255 everything
permit any any eq 443 tcp
allow an ip
!
exploitation forest esm config
NLS RESP-timeout 1
CPD cr id 1
!
!
!
!
!
!
!
control plan
!
!
!
!
profile MGCP default
!
!
!
!
!
access controller
Shutdown
!
!
!
Line con 0
exec-timeout 0 0
Synchronous recording
line to 0
exec-timeout 0 0
Synchronous recording
line vty 0 4
exec-timeout 0 0
Synchronous recording
entry ssh transport
line vty 5 15
exec-timeout 0 0
Synchronous recording
entry ssh transport
!
Scheduler allocate 20000 1000
!
Gateway Gateway-WebVPN-Cisco WebVPN
IP interface GigabitEthernet0/1 port 443
SSL rc4 - md5 encryption
SSL trustpoint TRUSTPOINT-MY
development
!
WebVPN install svc flash:/webvpn/anyconnect-linux-3.1.03103-k9.pkg sequence 1
!
WebVPN context Cisco WebVPN
title "Firewall.cx WebVPN - powered by Cisco"
SSL authentication check all
!
list of URLS "rewrite".
!
ACL "ssl - acl.
ip permit 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
permit ip 192.168.2.0 255.255.255.0 192.168.1.0 255.255.255.0
Licensing ip 192.168.0.0 255.255.0.0 192.168.0.0 255.255.0.0
!
login message "Cisco Secure WebVPN"
!
webvpnpolicy political group
functions required svc
filter tunnel ssl - acl
SVC-pool of addresses 'WEBVPN-POOL' netmask 255.255.255.0
generate a new key SVC new-tunnel method
SVC split include 192.168.1.0 255.255.255.0
Group Policy - by default-webvpnpolicy
AAA authentication list sslvpn
Gateway Cisco WebVPN bridge
Max-users 5
development
!
end
(###ISP))) is divided into subnets, subnets 1
S (# #ISP #) [254/0] via (# publicgateway #) GigabitEthernet0/1
###.###.0.0/16 is variably divided into subnets, 2 subnets, 2 masks
C ###.###.###.0/23 is directly connected, GigabitEthernet0/1
The ###.###.###.###/32 is directly connected, GigabitEthernet0/1
192.168.1.0/24 is variably divided into subnets, 2 subnets, 2 masks
C 192.168.1.0/24 is directly connected, GigabitEthernet0/0
The 192.168.1.254/32 is directly connected, GigabitEthernet0/0
192.168.2.0/32 is divided into subnets, subnets 1
S 192.168.2.100 [0/0] via 0.0.0.0, Virtual Network1
This backup will be restored as a whole via ASDM and substitute another configuration.
So, you might want to restore the backup to a fresh firewall and then import the configuration and the images of the SAA.
Dinesh Moudgil
===============
The configuration file to the startup was "startup-config '.
Internal ATA Compact Flash, 256 MB
BIOS Flash Firmware Hub @ 0xffe00000, 1024 KB
Start firmware: CN1000-MC-BOOT - 2.00
SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03
Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.05
1: Ext: GigabitEthernet0/1: the address is a493.4ca3.ce0b, irq 9
2: Ext: GigabitEthernet0/2: the address is a493.4ca3.ce0c, irq 9
3: Ext: GigabitEthernet0/3: the address is a493.4ca3.ce0d, irq 9
4: Ext: Management0/0: the address is a493.4ca3.ce09, irq 11
5: Int: internal-Data0/0: the address is 0000.0001.0002, irq 11
6: Int: internal-Control0/0: the address is 0000.0001.0001, irq 5
The maximum physical Interfaces: unlimited
VLAN maximum: 150
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
SSL VPN peers: 2
Total of the VPN peers: 750
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect Cisco VPN phone: disabled
AnyConnect Essentials: enabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabled
================
System image file is "disk0: / asa825 - k8.bin.
The configuration file to the startup was "startup-config '.
Internal ATA Compact Flash, 256 MB
BIOS Flash Firmware Hub @ 0xffe00000, 1024 KB
Start firmware: CN1000-MC-BOOT - 2.00
SSL/IKE firmware: CNLite-MC-Smls-PLUS - 2.03
Microcode IPSec:-CNlite-MC-IPSECm-HAND - 2.05
1: Ext: GigabitEthernet0/1: the address is 6073.5cab.3faf, irq 9
2: Ext: GigabitEthernet0/2: the address is 6073.5cab.3fb0, irq 9
3: Ext: GigabitEthernet0/3: the address is 6073.5cab.3fb1, irq 9
4: Ext: Management0/0: the address is 6073.5cab.3fb2, irq 11
5: Int: internal-Data0/0: the address is 0000.0001.0002, irq 11
6: Int: internal-Control0/0: the address is 0000.0001.0001, irq 5
The maximum physical Interfaces: unlimited
VLAN maximum: 150
Internal hosts: unlimited
Failover: Active/active
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 2
GTP/GPRS: disabled
SSL VPN peers: 2
Total of the VPN peers: 750
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect Cisco VPN phone: disabled
AnyConnect Essentials: enabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabled
L-ASA-AC-M-5520
:
ASA 9.1 Version 2
!
hostname DLSYD - ASA
domain delo.local
activate the encrypted password of UszxwHyGcg.e6o4z
names of
mask 172.16.1.60 - 172.16.1.70 255.255.255.0 IP local pool DLVPN_Pool
!
interface GigabitEthernet0/0
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/1
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/2
Post description
10 speed
full duplex
nameif Ext
security-level 0
IP 125.255.160.54 255.255.255.252
!
interface GigabitEthernet0/3
Description Int
10 speed
full duplex
nameif Int
security-level 100
IP 192.168.255.2 255.255.255.252
!
interface GigabitEthernet0/4
Shutdown
No nameif
no level of security
no ip address
!
interface GigabitEthernet0/5
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
management only
nameif management
security-level 100
IP 192.168.1.1 255.255.255.0
!
boot system Disk0: / asa912-smp - k8.bin
passive FTP mode
clock timezone IS 10
clock daylight saving time EDT recurring last Sun Oct 02:00 last Sun Mar 03:00
DNS lookup field inside
DNS domain-lookup Int
DNS server-group DefaultDNS
192.168.1.90 server name
192.168.1.202 server name
domain delo.local
permit same-security-traffic intra-interface
network dlau40 object
Home 192.168.1.209
network dlausyd02 object
host 192.168.1.202
network of the object 192.168.1.42
host 192.168.1.42
dlau-utm network object
host 192.168.1.50
network dlauxa6 object
Home 192.168.1.62
network of the 192.168.1.93 object
host 192.168.1.93
network dlau-ftp01 object
Home 192.168.1.112
dlau-dlau-ftp01 network object
network dlvpn_network object
subnet 172.16.1.0 255.255.255.0
the object-group Good-ICMP ICMP-type
echo ICMP-object
response to echo ICMP-object
ICMP-object has exceeded the time
Object-ICMP traceroute
ICMP-unreachable object
DLVPN_STAcl list standard access allowed 192.168.0.0 255.255.0.0
Standard access list DLVPN_STAcl allow 196.1.1.0 255.255.255.0
DLVPN_STAcl list standard access allowed 126.0.0.0 255.255.0.0
Ext_access_in access list extended icmp permitted any object-group Good-ICMP
Ext_access_in list extended access permitted tcp dlau-ftp01 eq ftp objects
Ext_access_in list extended access permit tcp any object dlausyd02 eq https
Ext_access_in list extended access permit tcp any object dlau-utm eq smtp
Ext_access_in list extended access permit tcp any object dlauxa6 eq 444
Ext_access_in access-list extended permitted ip object annete-home everything
pager lines 24
Enable logging
asdm of logging of information
MTU 1500 Ext
MTU 1500 Int
management of MTU 1500
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 713.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (Int, Ext) static source any any destination static dlvpn_network dlvpn_network non-proxy-arp
!
network dlausyd02 object
NAT (Int, Ext) interface static tcp https https service
dlau-utm network object
NAT (Int, Ext) interface static tcp smtp smtp service
network dlauxa6 object
NAT (Int, Ext) interface static tcp 444 444 service
network dlau-ftp01 object
NAT (Int, Ext) interface static tcp ftp ftp service
Access-group Ext_access_in in Ext interface
Route Ext 0.0.0.0 0.0.0.0 125.255.160.53 1
Route Int 192.168.0.0 255.255.0.0 192.168.255.1 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
AAA authentication enable LOCAL console
AAA authentication LOCAL telnet console
AAA authentication http LOCAL console
LOCAL AAA authentication serial console
the ssh LOCAL console AAA authentication
http server enable 44310
http server idle-timeout 30
http 192.168.0.0 255.255.0.0 Int
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec pmtu aging infinite - the security association
trustpool crypto ca policy
Telnet 192.168.1.0 255.255.255.0 management
Telnet timeout 30
SSH 192.168.0.0 255.255.0.0 Int
SSH timeout 30
SSH group dh-Group1-sha1 key exchange
Console timeout 0
No ipv6-vpn-addr-assign aaa
no local ipv6-vpn-addr-assign
management of 192.168.1.2 - dhcpd address 192.168.1.254
enable dhcpd management
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
NTP server 61.8.0.89 prefer external source
SSL encryption rc4-aes128-sha1 aes256-3des-sha1 sha1 sha1
WebVPN
port 44320
allow outside
Select Ext
AnyConnect essentials
AnyConnect image disk0:/anyconnect-win-3.1.05170-k9.pkg 1
AnyConnect enable
tunnel-group-list activate
internal GroupPolicy_DLVPN group strategy
attributes of Group Policy GroupPolicy_DLVPN
WINS server no
value of server DNS 192.168.1.90 192.168.1.202
client ssl-VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list DLVPN_STAcl
delonghi.local value by default-field
WebVPN
AnyConnect Dungeon-Installer installed
time to generate a new key 30 AnyConnect ssl
AnyConnect ssl generate a new method ssl key
AnyConnect ask flawless anyconnect
encrypted vendor_ipfx pb6/6ZHhaPgDKSHn password username
vendor_pacnet mIHuYi1jcf9OqVN9 encrypted password username
username admin password encrypted tFU2y7Uo15ahFyt4
type tunnel-group DLVPN remote access
attributes global-tunnel-group DLVPN
address pool DLVPN_Pool
Group Policy - by default-GroupPolicy_DLVPN
tunnel-group DLVPN webvpn-attributes
enable DLVPN group-alias
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the netbios
Review the ip options
inspect the ftp
inspect the tftp
!
global service-policy global_policy
SMTPS
Server 192.168.1.50
Group Policy - by default-DfltGrpPolicy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:67aa840d5cfff989bc045172b2d06212
: end
DLSYD - ASA #.
class inspection_default
inspect the icmp
inspect the icmp error
permit same-security-traffic intra-interface
object-network 192.168.0.0 255.255.255.0
object-network 192.168.10.0 255.255.255.0
inside_nat0_outbound list extended access allowed object-group ip DM_INLINE_NETWORK_1 192.168.2.0 255.255.255.0
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.10.0 255.255.255.0
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound
NAT (inside) 1 0.0.0.0 0.0.0.0
NAT (outside) 1 192.168.10.0 255.255.255.0
access-outside group access component software snap-in interface outside
Route outside 0.0.0.0 0.0.0.0 (the gateway IP) 1
WebVPN
allow outside
AnyConnect essentials
SVC disk0:/anyconnect-win-3.1.05152-k9.pkg 1 image
SVC profiles AnyConnectProfile disk0: / anyconnect_client.xml
enable SVC
tunnel-group-list activate
internal AnyConnectGrpPolicy group strategy
attributes of Group Policy AnyConnectGrpPolicy
WINS server no
value of 192.168.0.33 DNS server 192.168.2.33
VPN-session-timeout no
Protocol-tunnel-VPN l2tp ipsec svc
Split-tunnel-policy tunnelall
the address value AnyConnectPool pools
type tunnel-group AnyConnectGroup remote access
attributes global-tunnel-group AnyConnectGroup
address pool AnyConnectPool
authentication-server-group SERVER1_AD
Group Policy - by default-AnyConnectGrpPolicy
tunnel-group AnyConnectGroup webvpn-attributes
the aaa authentication certificate
activation of the Group _AnyConnect alias global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 nat (outside) 0 access-list outside_nat0 nat (outside) 1 192.168.10.0 255.255.255.0 access-list outside_nat0 extended permit ip any 192.168.10.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip 192.168.0.0 255.255.255.0 192.168.10.0 255.255.255.0
Maybe you are looking for