FTR 5.5.8.1 after FMS set 5.6.2 at level

Similar Questions

• The bad language displayed on the LCD after you set up the printer

  HP Photosmart C4450 all-in-one printer Solution Center keeps popping up the following:

  "The wrong language displayed on the LCD after you set up the printer.

  The printer has been upward and works well for months and all of a sudden it stopped working and refusing to speak English.

  It is totally insensitive to one of the buttons pressed. The LCD screen is white and gray just glowing.

  How can I solve this problem?

  Thanks in advance for any help.

  Hello

  I don't know how your printer got himself into this difficult situation, but I think a reset should back you on track.

  I think this could work to its original factory settings to install your printer.

  To do a complete reset follow these steps:

  1. disconnect the power cable from the back of the printer.

  2 do nothing for about 30 seconds.

  3 press and hold the Cancel & color copy, keep their detention now connect the power cord to the back of the printer.

  This should be left to the printer to the condition, it is in when you took it out of the box.

  I hope this helps.

• I have windows 8 in my computer toshiba laptop. After you set up windows for the updates it says «restoration of the changes...» Impossible to install the important updates'... What do I do?

  I have windows 8 in my computer toshiba laptop. After you set up windows for the updates it says «restoration of the changes...» Impossible to install the important updates'... What do I do?

  Hello

  Please, try the suggestions mentioned here and see if they help you:

  http://www.thewindowsclub.com/failure-configuring-Windows-updates

  Hope this helps, good luck :)

• After you set up the account on iPhone6 (iOS 9.1) all messages appeared: No sender; No subject; 31/12/69 the Assembly cannot be deleted. Messages can be sent ok.

  After setting up my account on iPhone6 (iOS 9.1) all messages appeared: No sender; No subject; 12/31/69. Editing does not have any message to delete. Messages can be sent ok. I sent a message from my office, on the phone, and while it was received, it was posted exactly as above. My e-mail account provider of Cableone and says that the problem is in the phone, and not with their system. Is there anything short of deleting the account and re-enter I can do?

  Do a forced restart: press and hold the home button and sleep, wait for the Apple logo, release the buttons.

• Axis changes after a set interval

  I have change my X axis range programmatically in various circumstances in my program. After the range changes, the method, and then calls another method to plot data. However, when I get the new method, the new range now has what I set the minimum or maximum. Why the range changing on me?

  Hello

  You set the mode to fixed axis?

  ScatterGraph1.XAxes.Item (0). Mode = AxisMode.Fixed
  
  ScatterGraph1.XAxes.Item (0). Range = new range (0, 10)

  Curt

• Internet does not work after you set up parental controls.

  I just create a new account and set up parental controls for it. Before I did the internet worked, but after you have configured parental controls, internet would not just work for my desktop which has a direct line.  I have a router and even after, the wifi signal and internet would always work however my line connection direct wouldn t.  I continued doing to solve the problem and start system restore, but every time I tried to set up the account with the internet parental control just doesn't work.

  Thanks in advance.

  
  

  Hello

  Maybe there's a settings problem.

  See this and the 'related links '.

  How to install and use Parental controls in Vista
  http://www.Vistax64.com/tutorials/95139-parental-controls-Setup-use.html

  and these:

  Setting up Windows Vista's Parental control
  http://www.bleepingcomputer.com/tutorials/tutorial139.html

  Set up Parental controls
  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-parental-controls

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• Cannot print after you set up the printer

  Original title: printer

  I thought that I just installed a HP Laserjet P1102w printer. I went through all the steps in my Windows 7 under "add a printer". I went to print a test page. Nothing. I get the notice to solve problems. I went through the troubleshooting process. No problem is listed as a problem. I try to print a test page once again, nothing happens.  I get the need to solve to find them again. ??? Can / will help you?

  Hi Clinton.

  I'll be happy to help you set up your printer and I appreciate your efforts to solve the problem.

  Many printing problems are caused by material which not is not set up quite right. Here are some ideas to solve common problems with the hardware of the printer.

  I would ask to refer to the article below which will help you to configure the printer from the start and you should be able to print it after.

  Solve printer problems

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

• ADF refresh page with page fragments jsff jsf after the set session variable

  Hello.

  I have a model that includes a button that allows you to select a profile, you push the button appear available profiles, choose one and press to accept. After that, I put a variable session successfully.

  I have a page of 'First' of jsf with two fragments of page jsff after seeing a link. The display link is composed by a headerView and detailView. The headerView had a variable binding. What I need, is that this parameter (bindVariableParameter) can be defined by the session of the model variable.

  That's what I get:

  I am in a homepage (separate Application Module), model button is pushed until I load "first" jsf page and after that, I go to the page jsf 'First', that information is loaded successfully. What I do in the Application Module is something like this:

  protected void prepareSession (one session) {}

  SessionScope card = ADFContext.getCurrent () .getSessionScope ();

  Company string = (String) sessionScope.get ("compId");

  System.out.println ("Default Comapny in British Colombia is:" + company);

  super.prepareSession (session);

  this.getSession () .getUserData () .put ("The company", company);

  System.out.println ("after the definition userData value card BC");

  }

  And in the variable binding expression of the headerView that I use:

  adf.userSession.userData.Company

  It works very well! But!

  When I press the button again and I chose another profile, the info is not updated. In the headerView or in the detailView.

  Also, when I go to the 'First' jsf page (without previously pressing the button model), I had no info, which is just, because I have no session variable. After I have press the model and select the profile, but the page is not refreshed.

  I tried many ways to this, but I'm lost.

  Could you help me?

  Kind regards.

  I'm not sure that understand your use case. What do I get, you set a parameter after that you press a button on the home page to pass this parameter to the first.jsf.

  Why don't you implement a method of the application module and call it directly with the parameter. The session of preparation will not be called whenever you browse but only init am.

  Do you need the parameter in the layer model or only in the display?

  Timo

• Satellite L - after that set BIOS to update the screen is black

  Hello

  I made an update of the BIOS on my Windows 7 64 bit, then the OS get frozen. After I restarted the laptop, ago just black and nothing appears on the laptop.

  What can I do?

  > What can I do?
  Time for boyfriend to ASP.

  It seems your BIOS did not complete successfully and the ROM module where the BIOS is stored has been damaged or has been flashed properly.

• Switch control Boolean to false automatically after a set time

  I'm trying to control when I register given by the presence of the user press a Boolean control on the front panel. I want the data to be saved for only 3 seconds and having the Boolean control automatically enabled to false so that the data will stop recording and control changes on the front but does not prevent the execution of the VI. The reason is that I want to have the user to create a settings file for a laser used outside of labview where entered the user through digital controls the current settings of laser and a wavelength of laser meter reading is found measured and saved in labview. So after that the data records for 3 seconds the user would input new parameters for the laser and then save the new configuration of the meter wavelength and repeat this operation several times.

  I tried a case hang as seen in the attached VI and you have also tried a state machine with control of ENUM. I can't get this thing to work. Any help would be appreciated.

  Thank you

  Hello

  Easier implementation is to have a state machine. You would have a State to collect data for a specific timer and another State to exit the VI.

• Problem with alert printer after you set up eprint

  I've just set up my HP eprint/connected to my printer HP Officejet 6700 account. I went through all the instructions and generated a code for me to record my printer. My printer came but I noticed that I have 2 alerts next to the printer which has been recorded. The alerts are:

  • Online
  • Problem with printer

  When I click on the message of the latter I get the following message

  • An unspecified problem was reported. Please check your printer.

  See the front panel of the printer for more information on the resolution of this condition

  I checked the printer, but it is not showing problems. I have however deleted the re-recorded new printer and web service. This time he seems to have solved the problem, but when I went back to the account later in the day the alert reappears.

  Could anyone help in this case.

  Hi BillyBoy59,

  Welcome to the HP Support forums.  I understand that you are getting a message "Problem with the printer" in connected HP.

  Connected HP sometimes gives a false report that there is a problem not specified with the printer. HP has been able to reproduce the error.  If there was a genuine mistake, the message would point to the problem (low on ink, paper, etc). Unspecified error message does not prevent you to use ePrint.

• error on a blue screen after you set new Athlon Proc and motherboard - Strop 0x0000007e (0xc0000005, 0xba2cb756, 0xba4c742c, 0xba4c7128)

  Original title: I need emergency with a blue screen error after new Athlon Proc and motherboard.!

  I had to fix my computer professional brothers due to its motherboard out. So, I advanced and ordered a motherboard latest and processor and also much more memory because the PC was about 6 years old. After installing, I he started and configured the BIOS and thought that it should start right up because it was working fine until the motherboard is out and also I left to himself, the hard drive that has XP installed, because he was also big enough for what he needs. But instead of cranking up XP, I get this error every time even when I try and boot in safe mode.

  I have also ordered him a new copy of Windows 7 to update his OS, but until I can get into XP and do an upgrade, I'm stuck. (I have to do an upgrade because of her inability to save his business files before exiting the motherboard.)

  * Without the [] error code: [stop: 0x0000007e (0xc0000005, 0xba2cb756, 0xba4c742c, 0xba4c7128)]

  Any help will be greatly appreciated, thank you.

  There is the old motherboard-specific drivers (for example, video, network, bridge, BIOS, etc.) in XP loads that are not compatible with the new motherboard. Conversely, you may need drivers specific to the new motherboard (see the disc that came with the motherboard for details). You might have to perform a repair installation on the existing XP. When you started on the XP installation disc, do not take into account the first mention of repair and then accept the option the second time, you are prompted to repair the existing installation.

  To be honest, you also get a new drive of 500 GB for Windows 7. A hard drive of six year, or approximately 80Gb (...?) and who will get eaten up real quickly by installation of Windows 7. In addition, I don't think you can update directly from XP to Windows 7. I'm sure that there must be a Vista installation in the meantime, but I was called incorrectly.

• wiil Windows does not recognize my existing scanner after that setting up a new printer, everything else works

  After having installed a new HP P1102w printer my computer says that my canon Quesqui is not actuvate. How can I solve the problem?

  Hi jburns44,

  Try the following.

  Method 1: Run automated troubleshooting and check if it helps.

  Hardware devices do not work or are not detected in Windows

  Method 2: Remove the scanner and install it again.

  a. click the Start button and then right click on my computer. Click on properties.

  b. click on the Hardware tab, and then click Device Manager.

  c. to see scanners that have been added to the computer, double-click imaging devices.

  d. right-click on the name of the scanner and then click Uninstall.

  See also:

  Microsoft Windows XP: install a scanner or digital camera

• After I set up windows mail through my provider I get a window that requires that me but a user name and pass word so I can connect to my e-mail of tpg

  I set up my windows mail through my provider which is proxad.net I put in place correctly, but when I want to receive emails there is a mistake. It requires
  I use a log on the user name and password, I used the same name and password on my windows account, you can surgess what I can do to find the problem.
  The respect of
  D. W. Ellison

  My answer is the same:

  Try to define under Tools | Accounts | Mail | Properties and if you still have this problem, make sure that there are no conflicting anti-virus (see www.oehelp.com/OETips.aspx#3) and try to compact and repair the database (see www.oehelp.com/WMUtil/).  If it still does not work, then see if you can connect using the web interface: https://postoffice.tpg.com.au/advanced/postoffice/login.php?TPG=9fq1mclnpfs3ohturt2red8bf3

  The parameters of Windows Mail (which is renamed in Vista OE) are the same for OE.  WMUtil is therefore exclusively for Windows Mail.  If your settings are incorrect then try and change them as indicated.  If the settings are correct and its doesn't work, then if it is not due to the antivirus or the database, and then its something on the server end and you can try and remedy the situation by contacting your provider.  If they put in place and its nothing does not work, then there's someone here can do to fix it.

  Steve

• Problems of Windows Mail after you set up Sky email on Android phone

  I had an account of Windows Messaging for many years. Computer uses Vista. My email account is with Sky.

  I just bought a phone Android (Samsung Galaxy S 2) and to allow emails sync with this I enabled IMAP in my sky email account, then made a new account in Windows Mail IMAP settings.

  The problem is that 10000 emails sent & received since 2008 trying to download. I continue to also invited to enter my username and password when I don't know the account entry is correct.

  Finally, when in Windows Mail, I see now 2 lost records, a related probably to my previous account POP (still alive but not by default) and the other put my new IMAP account (and by default).

  Can someone help me configure things properly? All I want is a set of folders in Windows Mail, and not that there are 10000 emails!

  Anyone knows if I can talk to a human being in this regard if necessary?

  Thank you

  Well, I did some research and was able to set up an IMAP account on my domain server.  There are some good instructions here: http://help.seattleserver.com/imap-setup-outlook-express that is specific to its installation, but you can see which screens, you will need to complete your details and options.

  With respect to the 10000 emails, I suggest that you perform the following steps at the server level, which is to move messages from the Inbox to a folder created by the user.  Then in OE, go to tools | Accounts | Mail | Properties | IMAP and uncheck the option to check messages in all folders.  When you synchronize it can ignore the folders created by the user rather then synchronize with it.

  See if that helps any.

  Steve