G580 turbo thrust does'nt work

Similar Questions

• X 230-Turbo Boost does not work when there is only the AC

  I changed the power manager in the State of Performance Max, but when he has only AC, Turbo Boost does not work. I need to install the battary simultaneously to do the Turbo Boost. If there is only battary, Turbo Boost can function normally.

  I googled this problem and it is said that Lenovo is doing this in order to avoid the lack of power when there is AC only.  How could I do Turbo Boost only works with AC (without battary on)?

  "evening.

  Welcome to the community!

  There are here some information that suggests that a 90 Watt power adapter will allow what you want, but I am mobile at the moment so my research capabilities are limited. Personally, I can't confirm that it works, however, I've never run without battery.

  Kind regards.

• Y580 Turbo Boost does not work except if hooked up

  While watching a youtube HD video, I noticed the processor did not work properly and that's why the video was stuttering. I checked and the intel turbo boost on a monitor version 2.6 and it showed that even on dynamic graphics Lenovo plan power than the processor was not using turbo boost. When running on the battery, the monitor displays also a leaf green and written below is "Energy Saver". If I plug the charger in the laptop, the problem goes away and I can see the Turbo works very well and with it the sheet and the "Energy Saver" will too.

  I've changed developed and even power settings made the processor state minimum 100% of battery, just as connected, so that it works just as well, but nothing helps. So I would like to know why the turbo boost function does not work then on the battery and only plugged him.

  yurajgill10,

  Intel's mode require more power that the battery can supply so it works only when the AC is plugged.

  Hope that helps.

• Turbo boost does not work when active hyperthreading - W520

  I have ignored this issue for a long time, until I've decided to try to understand and fix it. My W520 would never go beyond 2.40 GHz, I tried all the tests in the book. Manager power AC power, BIOS enabled, the max value performance in what concerns all, power settings windows too. stress tests, single thread, multi-threaded, has no importance, it has always been to 2.40 GHz or less (800 idling). After much trial and error, I found that this turbo would work properly if hyperthreading is disabled in the BIOS. The CPU module and then between 800 MHz to 3.5 GHz as it should with active turbo. Why can I not use hyperthreading AND turbo? Is this normal?

  I also noticed that in the BIOS there is no option for turbo-boost. Just hyperthreading, multi-core and speedstep.

  W520, i7-2760qm, BIOS 1.40, all the latest recommended updates.

  
  

• Tax Turbo installed but does not work on Windows Vista

  Tax Turbo installed but does not work. He says"this file does not have a program associated with it for performing this action. I don't know what the problem is. Exchanged the software still does not work.

  Sometimes, says "Application not found" program seemed to install and icon is on the screen, just at the moment where I got to run the program, it does not work and says it's "shutting down".  Any help?

  Have you ever successfully run this program on your machine?  So the system restore helps you, if if he was running very recently.

  How to repair the operating system and how to restore the configuration of the operating system to an earlier point in time in Windows Vista
  http://support.Microsoft.com/kb/936212/#appliesTo

  Which edition we talk to TurbTax, anything earlier than 2006 may not be not fully compatible with Vista?  64-bit versions may not be compatible at all?

  Have you tried right clicking on the shortcut to the program or the .exe and select "Run As Administrator"?

  The program will run in Mode safe?

  Vista advanced boot options
  http://Techblissonline.com/Vista-advanced-boot-options/

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7
  http://support.Microsoft.com/default.aspx/KB/929135

  Problems with the launch of other programs via shortcuts on your desktop?

  Try running ChkDsk to check your drive for errors. Right click on your drive icon / properties / tools / error checking.  Try first by checking do not each box (that it will run in read-only mode) to see if it reports any problems file or hard drive.  If so, restart it by checking both boxes and restart to allow him to attempt to fix any problems found.

• Here's a strange. I have a HTML page with this time a wmv video. It works perfectly from a USB stick or SD card, but does not work when they are copied to the hard drive

  I have an HTML page created with web expression 4. It contains only a wmv video. It works perfectly when it is called from a USB stick or SD card, but does not work when they are copied to the hard drive. The results are the same with IE and Firefox. It don't make no difference if I use Media Player V9 or V11. He has no control on the page Media Player. Video and html files are in the same directory. Here is the code snippet:

  LIFT, DRAG, THRUST and GRAVITY

  
  

  
  
  

  If I run it on a machine with Win 7 there is no problem.

  Richard Grosser

  Hi Richard c. Grosser,.

  Your question is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Microsoft Expression forums.

  http://social.expression.Microsoft.com/forums/en-us/categories

• Update of Vista 32 bit does not work after replacing the hard drive

  A month ago the hard drive of my computer (ACER Aspire 6920) had to be replaced. The disk image hard precedent (which includes the c: with Windows Vista Home Premium 32 bit, SP 2 build 6002) has been mirrored to the new hard drive. Everything seemed to work fine until I noticed that I don't have more updates from Microsoft. I tried a manual update and got the message that the update service was not working and I have to restart the computer. However, the Task Manager showed that the update service has been executed. Of course, I rebooted the computer, but nothing has changed.

  I found a whole bunch of recommendations for this issue in this forum, but nothing seems to work:

  • The Microsoft FixIT tool indicates a problem with the update of components, and then said that the problem had been solved successfully. However, the problem is still there and rerun the FixIt tool Gets the same message on a problem (yet) found and fixed.
  • I also stopped the update service, delete all content in Windows/C:\Windows\SoftwareDistribution and restarted the service. without success.
  • I've temporarily disabled my security suite (Eset Smart Security 6) and tried the update. I also have fittings the folder C:\Windows\SoftwareDistribution to the scope of the antivirus, without success. On the old hard drive, I used a different security suite so I thought that maybe the ESET (that I installed everything recently) could be the cause of the problem, but that doesn't seem to be the case.
  • I also followed the instructions provided by Microsoft at http://support.microsoft.com/kb/971058, but again, no change at all. However, it should be noted that registering some DLLs that Microsoft listed does not work (message that the DLL is not found or some server entry point (my translation, I'm using the German UI and don't know English good term; sorry) could not be found.)

  Http://support.microsoft.com/kb/947821 , I found another tool that supposedly can solve some problems of updating; I downloaded the version for Vista 32-bit, but it cannot install it on my computer (error code = 0xc8000247 during installation).

  So I'm really lost now what else to do. I would appreciate any suggestions. Please note that I am not technically very warned :)

  ARG, apologies.

  Was not aware that they had dropped support for Vista... (I myself have 'graduated' Vista earlier)

  The fact that you have not already installed TSRI is exactly your problem.

  Recent hard drives using 'Sectors 4 K', also known as 'Advanced Format Technology'.

  If the installed hard disk driver currently is not compatible with this specification,

  It will result in oddities like the status of the service Windows Update is not recognized correctly.

  Installation TSRI will fix this in most cases.

  Alternatively, if you are using Vista SP1 or later version (or 7 SP1), you can use the real driver.

  Since you are already updated to SP2, we will see if it is a viable solution.

  Go to: start-> Control Panel-> programs-> programs and features

  In the list of installed programs, locate and remove if found.

  -Intel Matrix Storage Manager

  -Intel Turbo Memory

  This should force your computer to go back to the real driver provided by Vista.

• Original image has disappeared I think off the hard drive and the BIOS password set up does not work?

  Someone please help me with this!

  I bought this laptop from a friend (have receipt) who sell it to me because the screen was cracked and spidered all out when you the activated. And everywhere he went to ask to get the screen fixed it is very expensive ($250 - $350) and he said that it would be just a newer laptop. So he sold me this which is a model Probook of HP4420s XT940UT #ABA. About a week after I bought this Probook friend who sold it to died me suddenly. It was sudden and terrible. Some time later, I had the time of the purchase of the LCD for this model, replace it myself (was very easy actually) and booted up the laptop with a new installation of Windows 7 Professional 64-bit Edition. After installing all my software and using the laptop for a while now, I wanted to get into the Bios that I've never done. So when I started the laptop, click ESC, then F10 to enter the BIOS, there were two places to enter a password is different then all Dell I've ever owned. One was mine I guees I put in place using HP protect tools and the other says BIOS/administrator. Well I can do most of the changes with the one I put in place with my password but my password does not work, nor can I get in some very significant changes that I wanted to do using Bios/administrator, as kindling the LoJack, namely the blocking of the hard drive etc. , turning on turbo boost, fan, etc. Well, since the person I bought is no longer with us, there is no one to turn to the answer to this question of administrator/BIOS password / problem.  I tried to take battery Rtype and restore that way, didn't work. Several times, I called HP and they sent me to a BIOS page to download the same BIOS, I have already, would not let me install it. When I bring up the command prompt and do not put anything in BiosConfigureUtility.exe happens, said just a wrong command. When I try to enter the BIOS through the C: file in the files of the SSM, I reach the BiosConfigUtility.exe file, click on it to open it and it just flashes a way small order page to fast to read what it says. I would like to have complete control over my laptop thinking I have a lot of time and money invested in it now. The problem would have something to do with installing the 64 bit version of Windows 7 instead of the 32 bits guess what it initially provided with?  Where can I find the UUID and what tech Department I would ask because if I have to call HP again and what other information should I have ready for them if you know? I have all the manuals and they say that this laptop is compatible with Windows 7 Ultimate 64 bit Pro is what I installed. I'm mixed responses from many different people on this and would like an answer from HP someone who has experience in dealing with the BIOS in the Probooks business models if possible please. I really like this Probook and have since become a big fan of most HP, Dell and Lenovo.  I intend to buy two probooks, one for my wife and one for my daughter because this one is like a MacBook, but better.  Thank you for reading this and I hope someone can help with more than one answer then GET AHOLD OF HP TECHNICAL TEAM. As I said, I did it.

  Model: HP Probook 4420 s

  Type: XT940UT #ABA

  Operating system: Windows 7 Ultimate

  BIOS version: 68AHHH Ver.F.20

  SM BIOS Version: 2.6

  Hardware Extraction layer: Version 6.1.7601.17514

  Jason,

  Sorry to hear about your friend and your problem.  The BIOS password cannot be reset without the help of HP.  They will need some information from your PC and increase your case.  I recommend you give them a call.

  -wes

• Administrator Bios password does not work on HP 4420 s XT940UT #ABA Windows 7 64-bit

  Someone please help me with this!

  I bought this laptop from a friend (have receipt) who sell it to me because the screen was cracked and spidered all out when you the activated. And everywhere he went to ask to get the screen fixed it is very expensive ($250 - $350) and he said that it would be just a newer laptop. So he sold me this which is a model Probook of HP4420s XT940UT #ABA. About a week after I bought this Probook friend who sold it to died me suddenly. It was sudden and terrible. Some time later, I had the time of the purchase of the LCD for this model, replace it myself (was very easy actually) and booted up the laptop with a new installation of Windows 7 Professional 64-bit Edition. After installing all my software and using the laptop for a while now, I wanted to get into the Bios that I've never done. So when I started the laptop, click ESC, then F10 to enter the BIOS, there were two places to enter a password is different then all Dell I've ever owned. One was mine I guees I put in place using HP protect tools and the other says BIOS/administrator. Well I can do most of the changes with the one I put in place with my password but my password does not work, nor can I get in some very significant changes that I wanted to do using Bios/administrator, as kindling the LoJack, namely the blocking of the hard drive etc. , turning on turbo boost, fan, etc. Well, since the person I bought is no longer with us, there is no one to turn to the answer to this question of administrator/BIOS password / problem.  I tried to take battery Rtype and restore that way, didn't work. Several times, I called HP and they sent me to a BIOS page to download the same BIOS, I have already, would not let me install it. When I bring up the command prompt and do not put anything in BiosConfigureUtility.exe happens, said just a wrong command. When I try to enter the BIOS through the C: file in the files of the SSM, I reach the BiosConfigUtility.exe file, click on it to open it and it just flashes a way small order page to fast to read what it says. I would like to have complete control over my laptop thinking I have a lot of time and money invested in it now. The problem would have something to do with installing the 64 bit version of Windows 7 instead of the 32 bits I suppose initially that he came with? I have all the manuals and they say that this laptop is compatible with Windows 7 Ultimate 64 bit Pro is what I installed. I'm mixed responses from many different people on this and would like an answer from HP someone who has experience in dealing with the BIOS in the Probooks business models if possible please. I really like this Probook and have since become big fan of most HP, Dell and Lenovo.  I intend to buy two probooks, one for my wife and one for my daughter because this one is like a MacBook, but better.  Thank you for reading this and I hope someone can help.

  Model: HP Probook 4420 s

  Type: XT940UT #ABA

  Operating system: Windows 7 Ultimate

  BIOS version: 68AHHH Ver.F.20

  SM BIOS Version: 2.6

  Hardware Extraction layer: Version 6.1.7601.17514

  Once you open a session with the service the customer of HP one case of pension, they will provide once the utility you and steps to execute it. who can capture the UUID. BTW - UUID is a unique ID for each machine (16 digits or more) stored in the BIOS itself.

  Once the results of the utility (UUID and other info) in the log file, shared with HP, they can generate a key file (SMC) to reset.

  Well, depertment of technical support can help you in it, no need to ask for anyone in particular or the Department.

  It will be useful.

• Safari does not work after installing macOS Sierra

  Safari and apple store does not work after installing macOS Sierra

  Alas, my crystal ball is in the shop for cleaning, so you will need to provide more details on what "doesn't work" and above all error messages. First of all, let's start the App Store. Provide as much information as possible for those of us who do not sit on your shoulder.

• My iPad Apple 3rd generation wifi + his cell phone does not work

  MY 3rd generation Apple iPad, wifi + cell

  model number MD408LL/a

  Serial number DM * VGL

  THE SOUND DOES NOT WORK

  < personal information under the direction of the host >

  All sounds, or simply notification and sounds apps (for example do music and videos app still have sound)? If notifications and apps you have notifications on mute: on the iPad side switch - Apple Support ? If the sounds in all applications which have tried for example soft-reset/reboot of the iPad, insert/remove the headphones?

• After recent, iPhone, 6, update, Windows, Explorer, does not work, see, iPhone

  I installed the latest update required for my iphone ios 6 a few days ago, and now when I try to download pictures from my iphone to my PC (via USB connection), the PC does not see the iphone.   iTunes sees it yet, but windows Explorer does not work.  It seems that some setting has been broken through the update of ios.  A way to solve this problem?

  Restart the computer and the iPhone. Unlock the iPhone before connecting it to the computer. Any change?

  TT2

• Open the link behind Mail does not work

  Sierra using my link opened behind Mail does not work. The link opens on the top of the window.

  This option works for me in Sierra... is working for you with your previous version of the OS?

• iPhone 5 home button does not work after ios 10

  My 5 Iphone Home button does not work after update final IOS version of 10.

  The home button works on the first push to wake the phone but it will not open the phone the second button.

  I activated the assist button, which does not work either. But what I discover is if I open device for assistance then touch and lock screen click on the button home will work once to open the phone. If I open any app I can't close it unless I go through the same routine.

  You attempted to restart your phone?

  You can do so by holding the sleep/wake button and the Home button simultaneously until the Apple logo appears

• Do not disturb (on request) does not work

  I have an iPhone 7 more with iOS 10.0.2. I had set up as NEW when I got it. I use the function do not disturb I SLEEP every night to block the incoming notifications apps and emails (including work with the application Outlook email). I leave the phone won't cut not so I can make sure my alarm wakes me up the morning. But it does not work. I still wake up emails and notifications of the app. It worked on my old iPhone with iOS 6, 8, 9 or even 10.

  I see a lot of old messages and questions about DND not work, but they were more specific to older phones and ' iOS.

  Anyone else having this problem?

  Any ideas for help?

  Thank you.

  I'm sure that I understood this.

  I had "only when locked" checked and not 'always' in settings do not disturb.

  I leave my iPhone unlocked all night using the bedside table Central app as my alarm clock.

  There we go.