Generator Adobe - default output folder / subfolder output does not support the scaling

Similar Questions

• Physical channel selected does not support the type of output required by virtual channel

  I use a box USB-6251.  Inside of MAX, I can set the device to Dev1 / ao1 sine wave generation and if he have output a sine wave.  When I use DAQmx DAQmxCreateAOFuncGenChan function I get error: selected physical channel does not support the type of output required by virtual channel.  The pilot DAQmx does FuncGen on the box USB-6251 or MAX out a set of tensions?

  Hi Paul,.

  Welcome to the Forums EITHER!  The DAQmxCreateAOFuncGenChan is supported only on products Elvis II.  For other devices, including the 6251, you must use the ordinary DAQmxCreateAOVoltageChan and create your own data buffer.  I would recommend looking in the following example:

  Start > all programs > National Instruments > NOR-DAQ > textual Code > ANSI C examples...

  Analog on > generate voltage > Cont Gen Volt Wfm - Int Clk

  In MAX the Sinewave output is used as a test signal - in this case MAX is a period of the wave sine values to write to the buffer and generate these data.  Again, you can produce a sine wave (or any other function) using the AOVoltageChan, but the AOFunctionGenChan is used only with Elvis II.  Just generate data points for the sine wave that will produce DAQ hardware.

  -John

• I can't download lightroom cc because "adobe does not support the system" I use. How the hell am I supposed to know what system he supports and how do I get the system that God Adobe says that I have? Googling lightroom cc requirements made n

  I can't download lightroom cc because "adobe does not support the system" I use. How the hell am I supposed to know what system he supports and how do I get the system that God Adobe says that I have? Googling lightroom cc requirements does not help.

  System requirements | Creative cloud

  The system requirements (lightroom)

• I have Adobe CS5 Extended. Recently bought a Canon 7 d MK II. Camera Raw does not support the 7 d MK II. Can I switch to 6 CS? That will solve my problem? I'm going to lose my plug ins

  I have Adobe CS 5 Extended. Recently bought a Canon 7 d MK II. The 5 CS camera raw does not support the MK II. Can I upgrade Photoshop CS 6? This will solve my problem? I lose my plug-ins?

  Yes you can upgrade: $400 for the scope. Creative Suite 6

  CS6 supports Adobe Camera Raw to 9.1 present however, your operating system must be Windows 7 or superior and OSX 10.7

  You will not lose your plugins, but you will need to reinstall on CS6. Check with the manufacturer of plugin for specific updates CS6.

• Unable to show a WMV file, because Windows 7 does not support the G2M4 codec

  I use windows 7 and I got a file wmv of my employer.  When I try to see I hear it but I can't.  The message I get is:

  "No decoder module appropriate:

  VLC does not support the audio or video format "G2M4". Unfortunately it is impossible for you to solve this problem. »

  Try to open in Windows Media Player and get this message "Windows Media Center cannot play the file because the required video codec is not installed on your computer."

  Tried to download the current codec installation package and I got the message "the program is blocked due to compatibility issues".

  Run the fixit from Microsoft to search for any missing codec and the report that came back that no codec is missing.

  Please tell me there is a way that this can be corrected.

  It might be worth a try to re - encode the. WMV file.

  In many cases, I found that convert a. WMV file
  to the. WMV format could produce a new version of the
  compatible file. Sounds redundant, I know, but it
  can work.

  Microsoft Expression Encoder 4 can perform the conversion.

  (FWIW... it's always a good idea to create a system)
  Restore point before installing software or updates)

  Download Microsoft Expression Encoder 4 with Service Pack 1 (SP1) (freeware)
  http://www.Microsoft.com/download/en/details.aspx?displaylang=en&ID=24601

  +++

  If you want to try Expression Encoder 4 following
  info can be useful:

  Start Microsoft Expression Encoder 4
  (Start / programs / Microsoft Expression /)
  Microsoft Expression Encoder 4)

  On the "Load a new project" screen...
  Left click... "Transcoding project '...

  When the program opens, click on... File / import...

  Left click (highlight) the. Left and WMV file, click the Open button.

  You will see the file in the "Multimedia content" pane

  In the right column... left click on the tab "Output"...

  Open the drop directory window and choose an output folder.
  (This is where you will find your converted file)

  On the left, click on the button "encode".

  Wait... video encoding CPU intensive and can
  be a slow process. It is always best if you do not have
  multi-task while files are encoded.

• No sound in 3g 2 files, error "Windows Media Player cannot play the file. The player does not support the format you are trying to play. »

  Original title: cannot get audio from video .3g2 (Windows 7)

  I have a number of videos that were recorded on a Motorola phone to format .3g2, when I played against them in windows XP Pro using what was the most recent media player, they played very well and the audio was present.

  I've since upgraded to Windows 7 Ultimate and have found that videos will play with media player sound is not output.

  I tried different players like VLC (same result, no sound) and came across one called SUPER from erightsoft which indeed works and allows me to re - encode to .wmv BUT when I do and you try to read the .wmv I encounter an error:

  "Windows Media Player cannot play the file. The player does not support the format you are trying to play. »

  When I clikc on help, I am led to a page with links on THIS forum.

  So here I am.

  Can someone explain what is happening, why it happens and how / if I can convert them into a playable (with audio) .wmv friendly format?

  Thank you

  Hi UbinTook,
  
  You found this message from Windows Media Player due to one of the following reasons.
   
  a. you try to play a file that is not supported by the player.
  b. you are trying to play a file that the player does not support, but the file was compressed by using a codec that is not supported by the player.
   
  Step 1:
   
  Confirm that you are trying to play a supported file type. The following article lists the types of files (formats) supported by Windows Media Player.
   
  Information on the types of media files that supports Windows Media Player
  http://support.Microsoft.com/kb/316992
   
  Note: if you have tried to play the file type is included in this table, the file might have been encoded with a codec that is not supported by Windows Media Player. If this is the case, Windows Media Player cannot play the file.
   
  Step 2:
   
  Download the necessary codec to play the file.
   
  For more information of Codec, see: Codec: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/codecs-frequently-asked-questions 

  Thank you, and in what concerns:
  I. Suuresh Kumar - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  

• Storage Array Type Config path: ATAS VMW_SATP_SVC does not support the configuration of the path on ESXi 5.0 u1

  Hello

  Below for the output of my blade IBM HS22., are there any problems with the configuration of the path.

  List of paths esxcli storage nmp
  SAS.5005076b08b7aaa4 - sas.a9501097faba7a - naa.600508e0000000007abafa971050a900
  The Runtime name: vmhba0:C1:T1:L0
  Feature: naa.600508e0000000007abafa971050a900
  Full device name: FREE Serial Attached SCSI (naa.600508e0000000007abafa971050a900) drive
  Group status: Active
  Table priority: 0
  Storage Array Type Config path: ATAS VMW_SATP_LOCAL does not support the configuration of the path.
  Path selection policy path Config: {current: Yes; favorite: Yes}

  FC.2fff0000c900009f:2ffd0000c900009f - fc.500507680100 b b 680 680:500507680130 - naa.60050768018105afc000000000000df0
  The Runtime name: vmhba2:C0:T3:L2
  Feature: naa.60050768018105afc000000000000df0
  Full device name: disk of IBM Fibre Channel (naa.60050768018105afc000000000000df0)
  Group status: Active
  Table priority: 0
  Storage Array Type Config path: ATAS VMW_SATP_SVC does not support the configuration of the path.
  Path selection policy path Config: {current: Yes; favorite: Yes}

  Kind regards

  Surya

  Hi Surya,

  No, it's not any problem with the configuration of your path.

  It only means that this policy does not allow additional configuration.

  I.e. with fixed NMP, you would be able to configure a preferred path allowing you to manually distribute the i/o load.

  Your current configuration does not offer this option.

  Kind regards

  Ralf

• What does that mean? -This problem occurred because your graphics card does not support the required version of DirectX. This version of Windows requires a DirectX 9.0 compatible video card or newer.

  I tried viewing a presentation power point and got to page 2 and my computer crashed.  Thought on... what he did previously trying to display a PPP file, but I thought that it was not my computer to the actual file.  now I have my doubts and also this time an error message came that said... This problem occurred because your graphics card does not support the required version of DirectX. This version of Windows requires a DirectX 9.0 compatible video card or newer.  can someone tell me what I should do next?

  You left out which version of DirectX has been shown.

  As far as I know, your Intel 945GM should support DirectX 9 and because you have XP sp3, you must have at least DirectX 9 installed.

  I met the following, but it shouldn't apply to Powerpoint:

  Some such as the Intel 945 GM Intel video cards have a design limitation which may cause problems when you try to run the Source Engine games. 3D graphics kernel does not support transformation of material, light and the vertex shader to similar technologies, which is an important part of the pipeline of 3D acceleration. Instead, this functionality is emulated in software that can reduce the compatibility and performance with 3D games.

  I don't have a solution for you (assuming that DXDIAG, in fact, reports to have DirectX 9 or higher).  You can see if you install a new driver support, but if it were me, I would be first contact Acer technical support or ask your question in another forum as one of the following conditions:

  Intel graphics Forum: http://communities.intel.com/community/tech/graphics
  Forum PowerPoint: http://answers.microsoft.com/en-us/office/forum/powerpoint (select the corresponding forum for your version of Powerpoint).  Include the results of DxDiag, including the version of DirectX.  If there is something unusual about the image that causes the crash, include this info as well.

  Normally, for notebook/laptop computer, it is better to get the drivers of the mfr of computer rather than the manufacturer of the device.

  Acer drivers for your computer are here: http://support.acer.com/us/en/product/default.aspx?tab=1&modelId=535 (you want the Intel VGA for XP driver)

  Intel has a newer driver: http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Internet+Devices&ProductLine=Netbooks&ProductProduct=Mobile+Intel%C2%AE+945GM+Express+Chipset+Family
  It's the main Intel support page: http://www.intel.com/p/en_US/support/highlights/graphics/945gm

• Error when you try to modify or to open a video (WLMP) using Windows Live Movie Maker: Movie maker does not support the selected file

  WLMP does not open on windows live movie maker?

  Well I made a video Windows live Director and saved it but when I try to open it to change some more it is said "Movie maker does not support the selected file" but he should not let me because I did in windows live Director please help!

  I'm having the same problem, but if I double click on the Window media player file appears help!

  ================================================
  Right-click the. WLMP file and try... Open with / Windows Live Movie Maker...

  See the following article

  Windows 7 - changing the programs that Windows uses by default
  http://Windows.Microsoft.com/en-us/Windows7/change-which-programs-Windows-uses-by-default

  Volunteer - MS - MVP - Digital Media Experience J - Notice_This is not tech support_I'm volunteer - Solutions that work for me may not work for you - * proceed at your own risk *.

• Photoshop CC 2015 does not support the import of videos in my version of Windows

  I have 8.1 Windows Pro installed on my PC and the trial version of Photoshop CC 2015 run but if I try to import and edit a video supposedly supported by the software I get the message "Could not complete your request because PS does not support the video in this version of Windows" edition of videos was one of the reasons I want to use Photoshop.  I can upload a video for editing in Adobe Premiere elements 13 then why he can't edit in Photoshop CC 2015

  What is the video format?   CC 2015 will certainly support video editing point 8.1 of Windows, but not with all formats.  If you have a format that is not supported, then convert to MP4 with brake hand.   It is practically an essential for video editors anyway, as it may low size of the video completed without loss of quality.

  https://handbrake.fr/

  It's free, btw.

• How can I load my photoshop CS6 cd to a new Macbook that has no cd slot and does not support the cd drive external mac.

  How can I load photoshop CS6 on a new macbook, which doesn't have a cd slot and does not support the cd drive external mac? I have the original cd of the program.

  Jake

  Download & install instructions https://forums.adobe.com/thread/2003339 can help

  -includes a link to access a page to download the Adobe programs if you do not have a disk or drive

  -you will need to enter your original serial number during the installation for non-Cloud programs

  - or kglad links in response to #1 here can help https://forums.adobe.com/thread/2081216

  Also go to https://forums.adobe.com/community/creative_cloud/creative_cloud_faq

  - and also read https://forums.adobe.com/thread/1146459

• Hi, I have 4 of Lightroom, but it does not support the new objective of pd 10-30 for my Nikon 1. It is supported in LR5. Can I download the profile of this lens and install in LR4?

  Hi, I have 4 of Lightroom, but it does not support the new objective of pd 10-30 for my Nikon 1. It is supported in LR5. Can I download the profile of this lens and install in LR4?

  Wow! It worked! Thank you very much! You just saved me buying a new verion of Lightroom (which is of course why Adobe does not update these profiles automatically).

  Thank you very much!

• Safe fonts Web does not support the Norwegian letters æ, o and a. when published. We do not want to use the fonts listed, because the quality is not good published wen.  Any tips?

  Safe fonts Web does not support the Norwegian letters æ, o and a. when published. We do not want to use the fonts listed, because the quality is not good published wen.  Any tips?

  Hello

  Please try to use the glyphs Panel available with Muse.

  Adobe help Muse | Use of text

  It will be useful,

  Sonam

• Extensions Manager CC does not support the hybrid group of extensions?

  Document adobe® Extension Builder 3.0 release notes ( http://download.macromedia.com/pub/labs/extensionbuilder3/extensionbuilder_releasenotes_06 2413.pdf ) which says " " Extension Manager does not support the hybrid group of extensions"(issue #3549187).  Hmm... Really? Extensions of the hybrid is no longer supported?

  Extension Manager supports hybrid extensions. But we define hybrid as extension: an extension that contains the file mxi, zero, one or more ordinary files and one or more CSXS extensions incorporated. In other words, only CSXS extensions can be incorporated in hybrid extension. If you embed another extension extension or regular hybrid in an extension of the hybrid, it is an invalid extension from the point of view of the extensions Manager.

• The document _ is on a volume that does not support the permanent version storage.  You will not be able to access older versions of this document once you close.

  I recently started getting this strange message, usually when a Pages document is closed:

  «The document _ is on a volume that does not support the permanent version storage.»  You can access older versions of this document once you close. »

  All my research (apple.com and on the internet) have not enabled all the information on this message.

  Hi Larry,

  The 'volume' is a hard disk, a partition on a hard drive or a storage as a USB device.

  OS X automatically saves your document frequent while you work on it. If the volume of the device / it records on a summer formatted to allow 'versioning', you will be able to use Time Machine to open previous versions of your document. If it has not been formatted like that, you get the message see you, and only the current version of the document will be saved.

  Kind regards

  Barry